This thesis focuses on the effect of microstructural variation on the mechanical properties and deformation behavior of ductile iron. To research and determine these effects, two grades of ductile iron, (i) GJS-500-7 and (ii) high silicon GJS-500-14, were cast in a geometry containing several plates with different section thicknesses in order to produce microstructural variation. Microstructural investigations as well as tensile and hardness tests were performed on the casting plates. The results revealed higher ferrite fraction, graphite particle count, and yield strength in the high silicon GJS-500-14 grade compared to the GJS-500-7 grade. To study the relationship between the microstructural variation and tensile behavior on macroscale, tensile stress-strain response was characterized using the Ludwigson equation. The obtained tensile properties were modeled, based on the microstructural characteristics, using multiple linear regression and analysis of variance (ANOVA). The models showed that silicon content, graphite particle count, ferrite fraction, and fraction of porosity are the major contributing factors that influence tensile behavior. The models were entered into a casting process simulation software, and the simulated microstructure and tensile properties were validated using the experimental data. This enabled the opportunity to predict tensile properties of cast components with similar microstructural characteristics. To investigate deformation behavior on micro-scale, a method was developed to quantitatively measure strain in the microstructure, utilizing the digital image correlation (DIC) technique together with in-situ tensile testing. In this method, a pit-etching procedure was developed to generate a random speckle pattern, enabling DIC strain measurement to be conducted in the matrix and the area between the graphite particles. The method was validated by benchmarking the measured yield strength with the material’s standard yield strength. The microstructural deformation behavior under tensile loading was characterized. During elastic deformation, strain mapping revealed a heterogeneous strain distribution in the microstructure, as well as shear bands that formed between graphite particles. The crack was initiated at the stress ranges in which a kink occurred in the tensile curve, indicating the dissipation of energy during both plastic deformation and crack initiation. A large amount of strain localization was measured at the onset of the micro-cracks on the strain maps. The micro-cracks were initiated at local strain levels higher than 2%, suggesting a threshold level of strain required for micro-crack initiation. A continuum Finite Element (FE) model containing a physical length scale was developed to predict strain on the microstructure of ductile iron. The material parameters for this model were calculated by optimization, utilizing the Ramberg-Osgood equation. The predicted strain maps were compared to the strain maps measured by DIC, both qualitatively and quantitatively. To a large extent, the strain maps were in agreement, resulting in the validation of the model on micro-scale. In order to perform a micro-scale characterization of dynamic deformation behavior, local strain distribution on the microstructure was studied by performing in-situ cyclic tests using a scanning electron microscope (SEM). A novel method, based on the focused ion beam (FIB) milling, was developed to generate a speckle pattern on the microstructure of the ferritic ductile iron (GJS-500-14 grade) to enable quantitative DIC strain measurement to be performed. The results showed that the maximum strain concentration occurred in the vicinity of the micro-cracks, particularly ahead of the micro-crack tip. / Denna avhandling fokuserar på effekten av variationer i mikrostrukturen på mekaniska egenskaper och deformationsbeteende hos segjärn. För att undersöka dessa effekter, två olika sorter av segjärn, (i) GJS-500-7 och (ii) högkisellegerad GJS-500-14, gjutits till plattor av olika tjocklekar för att generera mikrostrukturvariationen. Mikrostrukturundersökning, samt drag- och hårdhetsprov gjordes på de gjutna plattorna. Resultaten visade att en högre ferritfraktion, grafitpartikelantal och sträckgräns i den högkisellegerade GJS-500-14-sorten jämfört med GJS-500-7. För att studera förhållandet mellan mikrostrukturell variation och spännings-töjningsbeteendet på makroskala, modellerades detta med hjälp av Ludwigson-ekvationen. De erhållna spännings-töjningsegenskaperna modellerades baserat på mikrostrukturell karaktäristika genom multipel linjärregression och variansanalys (ANOVA). Modellerna visade att kiselhalt, grafitpartikelantal, ferritfraktion och porfraktion var de viktigaste bidragande faktorerna. Modellerna implementerades i ett simuleringsprogram för gjutningsprocessen. Resultatet från simuleringen validerades med hjälp av experimentella data som inte ingick i underlaget för regressionsanalysen. Detta möjliggjorde att prediktera spännings-töjningsbeteendet och dess variation hos gjutna segjärns komponenter med liknande sammansättning och gjutna tjocklekar som användes i denna studie. För att kunna undersöka deformationsbeteendet på mikroskala utvecklades en metod för kvantitativ mätning av töjning i mikrostrukturen, genom DIC-tekniken (digital image correlation) tillsammans med in-situ dragprovning. I denna metod utvecklades en grop-etsningsprocess för att generera ett slumpvis prickmönster, vilket möjliggjorde DIC-töjningsmätning i matrisen och i området mellan grafitpartiklarna med tillräcklig upplösning. Metoden validerades genom benchmarking av den uppmätta sträckgränsen mot materialets makroskopiska sträckgräns mätt med konventionell dragprovning. Det mikrostrukturella deformationsbeteendet under dragbelastning karakteriserades. Under elastisk deformation avslöjade töjningsmönstret en heterogen töjningsfördelning i mikrostrukturen, och bildandet av skjuvband mellan grafitpartiklar. Sprickbildning initierades vid låg spänning och redan vid de spänningsnivåer som ligger vis ”knät” på dragprovningskurvan, vilket indikerar energidissipering genom både begynnande plastisk deformation och sprickbildning. Den lokala töjningen vis sprickinitiering skedde då den lokala töjningen översteg 2%, vilket indikerar att detta skulle kunna vara en tröskelnivå för den töjning som erfordras för initiering av mikro-sprickor. En kontinuum Finita Element (FE) modell utvecklades för att prediktera töjningen hos ett segjärn och dess fördelning i segjärns mikrostruktur. Materialparametrarna för denna modell optimerades genom att anpassa parametrarna i Ramberg-Osgood ekvationen. De predikterade töjningsfördelningarna jämfördes med de experimentell uppmätta töjningsmönstren uppmätta med DIC, både kvalitativt och kvantitativt. Töjningsmönstren överensstämde i stor utsträckning, vilket resulterade i att modellerna kunde anses vara validerade på mikronivå. För att kunna mäta töjningsmönster under dynamiska förlopp på mikronivå utvecklades en metod för att skapa prickmönster och att utföra in-situ CT provning i ett svepeletronmikroskop (SEM). Prickmönstret skapades genom avverkning med en fokuserad jonstråle (FIB), och provades på det ferritiska segjärnet (GJS-500-14 grad). Resultaten visade att maximal töjningskoncentration fanns i närheten av mikrosprickorna, framförallt framför sprickspetsen.

No presente trabalho foi avaliado o efeito da microestrutura e da capacidade de suportar carregamento de camadas nitretadas produzidas em aços ferramenta AISI H13 e AISI D2 sobre a aderência e a resistência ao desgaste microabrasivo de revestimentos de TiN-PVD. Em cada um desses aços, foram produzidas camadas nitretadas de diferentes estruturas e espessuras, e foram determinadas experimentalmente as curvas potencial início de formação de camada branca, para a nitretação a 520oC. Para o aço ferramenta AISI H13, o emprego de tempos de pré-tratamento de nitretação mais prolongados ( aproximadamente 11 h) foi necessário para aprofundar a camada nitretada e, conseqüentemente, aumentar a capacidade de suportar carregamento dos revestimentos, evitando a formação de bordas que provocam o lascamento e a escamação das camadas de TiN. Observou-se que esse tipo de falha persiste se a zona de endurecimento for pouco profunda, uma vez que a transição de propriedades mecânicas da camada de TiN para o núcleo não nitretado continua abrupta e a capacidade de suportar carregamento da camada nitretada ainda é baixa. Por outro lado, curtos tempos de nitretação (aproximadamente 42 min.) foram suficientes para aumentar a aderência das camadas de TiN ao aço ferramenta D2, pois o núcleo não nitretado desse aço possui uma capacidade de suportar carregamento razoável. Observou-se que a resistência ao desgaste microabrasivo e a aderência dos revestimentos são prejudicadas com a presença de uma camada preta na interface camada de TiN/camada nitretada. Quando a superfície dos revestimentos é carregada, falhas do tipo “casca de ovo" facilmente ocorrem. / In this work, the influence of both the microstructure and the load-bearing capacity of nitrided layers, formed on top of AISI D2 and AISI H13 tool steels, on adhesion and wear resistance of PVD-TiN coatings was studied. The threshold nitriding potential curves for the above mentioned steels and the optimum conditions of the pre-treatments which increased the adhesion as well as the wear resistance of the PVD-TiN were determined experimentally. By using longer nitriding times (about 11 h) and lower nitrogen contents in the gas mixture (about N2-5%vol.), it was possible to minimize the pile-up degree of the TiN/H13 nitrided substrates and, consequently, the occurrence of coatings chipping. This flaw persists when the nitrided layer is thin, due to an abrupt transition of mechanical properties at the TiN coating / steel core interface. Shorter nitriding times (about 42 min.) and lower nitrogen contents (about N2-5%vol.), on the other hand, are sufficient to guarantee a better adhesion of TiN coatings on AISI D2 tool steel, as the core of such steel possesses relatively better load-bearing capacity than the AISI H13 tool steel. The presence of a black layer at the TiN/nitrided layer interface was observed in all coatings deposited over nitrided layers produced above the threshold nitriding potential curves. This layer affects adversely the wear resistance and the adhesion of the TiN coatings. When higher loads are applied on the coated surface, “egg shell" type flaws easily occur.

No presente trabalho foi avaliado o efeito da microestrutura e da capacidade de suportar carregamento de camadas nitretadas produzidas em aços ferramenta AISI H13 e AISI D2 sobre a aderência e a resistência ao desgaste microabrasivo de revestimentos de TiN-PVD. Em cada um desses aços, foram produzidas camadas nitretadas de diferentes estruturas e espessuras, e foram determinadas experimentalmente as curvas potencial início de formação de camada branca, para a nitretação a 520oC. Para o aço ferramenta AISI H13, o emprego de tempos de pré-tratamento de nitretação mais prolongados ( aproximadamente 11 h) foi necessário para aprofundar a camada nitretada e, conseqüentemente, aumentar a capacidade de suportar carregamento dos revestimentos, evitando a formação de bordas que provocam o lascamento e a escamação das camadas de TiN. Observou-se que esse tipo de falha persiste se a zona de endurecimento for pouco profunda, uma vez que a transição de propriedades mecânicas da camada de TiN para o núcleo não nitretado continua abrupta e a capacidade de suportar carregamento da camada nitretada ainda é baixa. Por outro lado, curtos tempos de nitretação (aproximadamente 42 min.) foram suficientes para aumentar a aderência das camadas de TiN ao aço ferramenta D2, pois o núcleo não nitretado desse aço possui uma capacidade de suportar carregamento razoável. Observou-se que a resistência ao desgaste microabrasivo e a aderência dos revestimentos são prejudicadas com a presença de uma camada preta na interface camada de TiN/camada nitretada. Quando a superfície dos revestimentos é carregada, falhas do tipo “casca de ovo” facilmente ocorrem. / In this work, the influence of both the microstructure and the load-bearing capacity of nitrided layers, formed on top of AISI D2 and AISI H13 tool steels, on adhesion and wear resistance of PVD-TiN coatings was studied. The threshold nitriding potential curves for the above mentioned steels and the optimum conditions of the pre-treatments which increased the adhesion as well as the wear resistance of the PVD-TiN were determined experimentally. By using longer nitriding times (about 11 h) and lower nitrogen contents in the gas mixture (about N2-5%vol.), it was possible to minimize the pile-up degree of the TiN/H13 nitrided substrates and, consequently, the occurrence of coatings chipping. This flaw persists when the nitrided layer is thin, due to an abrupt transition of mechanical properties at the TiN coating / steel core interface. Shorter nitriding times (about 42 min.) and lower nitrogen contents (about N2-5%vol.), on the other hand, are sufficient to guarantee a better adhesion of TiN coatings on AISI D2 tool steel, as the core of such steel possesses relatively better load-bearing capacity than the AISI H13 tool steel. The presence of a black layer at the TiN/nitrided layer interface was observed in all coatings deposited over nitrided layers produced above the threshold nitriding potential curves. This layer affects adversely the wear resistance and the adhesion of the TiN coatings. When higher loads are applied on the coated surface, “egg shell” type flaws easily occur.