A research report submitted to the faculty of Engineering and the Built Environment, University of the Witwatersrand, Johannesburg, in partial fulfilment of the requirements for the degree of Master of Science in Engineering. / The theory of Mine Call Factor (MCF) compares the sum of metal produced in recovery plus residue to the metal called for by the mines evaluation method expressed as a percentage. This MCF concept is well known in underground scenarios and therefore this report highlights the MCF issues and the variable components affecting it from a surface mine perspective. The MCF investigation established the relationship between actual measurements and reporting against measurement protocols. Such measurements include “tonnage, volume, relative density, reconciliation strategy, and truck tonnage determination, sampling and assay standards. This study investigated how these measurements are conducted on Iduapriem Mine according to the mine’s standard operating procedures (SOP). An improvement of documents towards a metal accounting protocol based on the AMIRA protocol is recommended. The mine’s current quality control protocol was further expanded to reflect current practices. The mine to mill reconciliation compared production estimates from various sources (resource model, grade control model, pit design, plant and stockpile, truck tally, stockpile and plant feed, plant feed and plant received) in the period 2009 and 2010. Reconciliation factors expressed as a percentage were statistically analysed for discrepancies for tonnages and grades. It was realised that there is more confidence in mass (tonnage) measurement compared to grade. A generic mine to mill reconciliation path was suggested to be used by the mine.

Thesis (MS)--University of Montana, 2009. / Contents viewed on January 15, 2010. Title from author supplied metadata.

The thesis starts by defining technological change, productivity and safety. Different definitions are discussed and their merits compared. A brief history of coal mining, together with a description of the state of the mining industry at present is given. Technological innovations recently adopted by the industry are discussed. The concept of productivity in relation to the coal industry of the U.K., and the deficiencies of the present measurement technique, are fully explained. Safety in the coal mining industry of the U.K. is investigated. A brief history is given, together with a full discussion of the consequences and costs of accidents. The concept of technical productivity is introduced and its relation to total productivity explained. The total productivity concept is then applied to longwall coal faces. A multi-variable non-linear model is devised which represents mean total productivity of all longwall faces to an accuracy of about J7G. The model is tested and a forecasting method suggested. Total productivity components are analysed and values for the productivity of various inputs during the period 1958-1980 given. Similarly, a model for representing safety, based on costs, is introduced, tested for accuracy and its components analysed. By applying marginal analysis to the total productivity and safety models, the influence of technological change on productivity and safety are quantified. It is concluded that a new method for measuring productivity should be adopted, in which case total productivity would be the most realistic and comprehensive choice. The models introduced can serve as useful tools in planning and forecasting, as well as being used to measure productivity and safety. Since this work has been in progress, work at the NCB has also led to consideration of improved measures of productivity.

No description available.

No description available.

Rocks of the South Island of New Zealand are locally enriched in metalloids, namely arsenic (As), antimony (Sb) and boron (B). Elevated levels of As and Sb can be found in sulphide minerals mostly in association with mesothermal gold deposits, whereas B enrichment occurs in marine influenced coal deposits. The mobility of these metalloids is important because they can be toxic at relatively low levels (e.g. for humans >0.01 mg/L of As). Their mobilisation occurs naturally from background weathering of the bedrock. However, mining and processing of coal and gold deposits, New Zealand's most economically important commodities, can significantly increase metalloid mobility. In particular, historic mines and associated industrial sites are known to generate elevated metalloid levels because of the lack of site remediation upon closure. This work defines and quantifies geological, mining, post-mining and regional processes with respect to metalloid, especially As, mobility. At the studied historic gold mines, the Blackwater and Bullendale mines, Sb levels in mineralised rocks were generally negligible (<14 ppm) compared to As (up to 10,000 ppm). Thus, Sb concentrations in solids and in water were too low to yield any meaningful information on Sb mobility. In contrast, dissolved As concentrations downstream from mine sites were found to be very high (up to 59 mg/L) (background = 10⁻� mg/L). In addition, very high As concentrations were found in residues (up to 40 wt%) and site substrate (up to 30 wt%) at the Blackwater processing sites (background < 0.05 wt%). Here, roasting of the gold ore converted the orginal As mineral, arsenopyrite, into the mineral arsenolite (As[III] trioxide polymorph) and volatilised the sulphur. The resultant sulphur-defficient chemical system is driven by arsenolite dissolution and differs significantly from mine sites where arsenopyrite is the main As source. Arsenolite is significantly more soluble than arsenopyrite. In the surficial environment, arsenolite dissolution is limited by kinetics only, which are slow enough to preserve exposed arsenolite over decades in a temperate, wet climate. This process results in surface waters with up to ca. 50 mg/L dissolved As. In reducing conditions, dissolved As concentrations are also controlled by the solubility of arsenolite producing As concentrations up to 330 mg/L. Field based cathodic stripping voltammetry showed that the As[III]/As[V] redox couple, in particular the oxidation of As[III], has a major control on system pH and Eh. Site acidification is mainly caused by the oxidation of As[III], resulting in a close link between As[V] concentrations and pH. Similarly, a strong correlation between calculated (Nernstian) and measured (electrode) Eh was found in the surface environment, suggesting that the overall Eh of the system is, indeed, defined by the As[III]/As[V] redox couple. Once the metalloid is mobilised from its original source, its mobility is controlled by at least one of the following attenuation processes: (a) precipitation of secondary metalloid minerals, (b) co-precipitation with - or adsorption to - iron oxyhydroxide (HFO), or (c) dilution with background waters. The precipitation of secondary minerals is most favoured in the case of As due to the relatively low solubility of iron arsenates, especially at low pH (~0.1 mg/L). Observations suggest that scorodite can be the precursor phase to more stable iron arsenates, such as kankite, zykaite, bukovskyite or pharmacosiderite and their stability is mainly controlled by pH, sulphur concentrations and moisture prevalence. Empirical evidence indicates that the sulphur-containing minerals zykaite and bukovskyite have a similar pH dependence to scorodite with solubilities slightly lower than scorodite and kankite. If dissolved As concentrations decline, iron arsenates potentially become unstable. Their dissolution maintains a pH between 2.5 and 3.5. This acidification process is pivotal with respect to As mobility, especially in the absence of other acidification processes, because iron arsenates are several orders of magnitude more soluble in circum-neutral pH regimes (~100 mg/L). From this, it becomes apparent that external pH modifications, for example as part of a remediation scheme, can significantly increase iron arsenate solubility and resultant As mobility. In contrast to As, the precipitation of secondary Sb and B minerals is limited by their high solubilities, which are several orders of magnitude higher than for iron arsenates. Thus, secondary Sb and B minerals are restricted to evaporative waters, from which they can easily re-mobilised during rain events. Metalloid adsorption to HFO is mainly controlled or limited by the extent of HFO formation, which in turn is governed by the availability of Fe and prevailing Eh-pH conditions. Thus, mineralisation styles and associated geochemical gradients, in particular pyrite abundance, can control the amount of HFO and consequent metalloid attenuation, and these can vary even within the same goldfleld. Furthermore, it was found that there is a mineralogical gradation between ferrihydrite with varying amounts of adsorbed As, amorphous iron arsenates and crystalline iron arsenates, suggesting that the maturity of mine waste is an important factor in As mineralogy. Once dissolved metalloids enter the hydrosphere, dilution is the main control on metalloid attenuation, which is especially pronounced at the inflow of tributaries. Dilution is, therefore, closely related to the size and frequency of these tributaries, which in turn are controlled by the regional topography and climate. Dilution is a considerably less effective attenuation mechanism and anomalous metalloid concentrations from mining related sites can persist for over 10 km downstream. The complex and often inter-dependent controls on metalloid mobility mean that management decisions should carefully consider the specific site geochemistry to minimize economic, health and environmental risks that can not be afforded. On a regional scale, background metalloid flux determines the downstream impact of an anomalous metalloid source upstream. For example, the Bullendale mine is located in a mountainous region, where rapidly eroding slopes expose fresh rock and limit the extent of soil cover and chemical weathering. Consequently, the background As flux is relatively low and As point sources, such as the Bullendale mine, present a significant contribution to the downstream As flux. In contrast, the bedrock at the Blackwater mine has undergone deep chemical weathering, resulting in an increased background mobilisation of As. Thus, the Prohibition mill site discharge, for example, contributes only about 10% to the downstream As flux. This information is relevant to site management decisions because the amount of natural background metalloid mobilisation determines whether site remediation will influence downstream metalloid chemistry on a regional scale.

Rocks of the South Island of New Zealand are locally enriched in metalloids, namely arsenic (As), antimony (Sb) and boron (B). Elevated levels of As and Sb can be found in sulphide minerals mostly in association with mesothermal gold deposits, whereas B enrichment occurs in marine influenced coal deposits. The mobility of these metalloids is important because they can be toxic at relatively low levels (e.g. for humans >0.01 mg/L of As). Their mobilisation occurs naturally from background weathering of the bedrock. However, mining and processing of coal and gold deposits, New Zealand's most economically important commodities, can significantly increase metalloid mobility. In particular, historic mines and associated industrial sites are known to generate elevated metalloid levels because of the lack of site remediation upon closure. This work defines and quantifies geological, mining, post-mining and regional processes with respect to metalloid, especially As, mobility. At the studied historic gold mines, the Blackwater and Bullendale mines, Sb levels in mineralised rocks were generally negligible (<14 ppm) compared to As (up to 10,000 ppm). Thus, Sb concentrations in solids and in water were too low to yield any meaningful information on Sb mobility. In contrast, dissolved As concentrations downstream from mine sites were found to be very high (up to 59 mg/L) (background = 10⁻� mg/L). In addition, very high As concentrations were found in residues (up to 40 wt%) and site substrate (up to 30 wt%) at the Blackwater processing sites (background < 0.05 wt%). Here, roasting of the gold ore converted the orginal As mineral, arsenopyrite, into the mineral arsenolite (As[III] trioxide polymorph) and volatilised the sulphur. The resultant sulphur-defficient chemical system is driven by arsenolite dissolution and differs significantly from mine sites where arsenopyrite is the main As source. Arsenolite is significantly more soluble than arsenopyrite. In the surficial environment, arsenolite dissolution is limited by kinetics only, which are slow enough to preserve exposed arsenolite over decades in a temperate, wet climate. This process results in surface waters with up to ca. 50 mg/L dissolved As. In reducing conditions, dissolved As concentrations are also controlled by the solubility of arsenolite producing As concentrations up to 330 mg/L. Field based cathodic stripping voltammetry showed that the As[III]/As[V] redox couple, in particular the oxidation of As[III], has a major control on system pH and Eh. Site acidification is mainly caused by the oxidation of As[III], resulting in a close link between As[V] concentrations and pH. Similarly, a strong correlation between calculated (Nernstian) and measured (electrode) Eh was found in the surface environment, suggesting that the overall Eh of the system is, indeed, defined by the As[III]/As[V] redox couple. Once the metalloid is mobilised from its original source, its mobility is controlled by at least one of the following attenuation processes: (a) precipitation of secondary metalloid minerals, (b) co-precipitation with - or adsorption to - iron oxyhydroxide (HFO), or (c) dilution with background waters. The precipitation of secondary minerals is most favoured in the case of As due to the relatively low solubility of iron arsenates, especially at low pH (~0.1 mg/L). Observations suggest that scorodite can be the precursor phase to more stable iron arsenates, such as kankite, zykaite, bukovskyite or pharmacosiderite and their stability is mainly controlled by pH, sulphur concentrations and moisture prevalence. Empirical evidence indicates that the sulphur-containing minerals zykaite and bukovskyite have a similar pH dependence to scorodite with solubilities slightly lower than scorodite and kankite. If dissolved As concentrations decline, iron arsenates potentially become unstable. Their dissolution maintains a pH between 2.5 and 3.5. This acidification process is pivotal with respect to As mobility, especially in the absence of other acidification processes, because iron arsenates are several orders of magnitude more soluble in circum-neutral pH regimes (~100 mg/L). From this, it becomes apparent that external pH modifications, for example as part of a remediation scheme, can significantly increase iron arsenate solubility and resultant As mobility. In contrast to As, the precipitation of secondary Sb and B minerals is limited by their high solubilities, which are several orders of magnitude higher than for iron arsenates. Thus, secondary Sb and B minerals are restricted to evaporative waters, from which they can easily re-mobilised during rain events. Metalloid adsorption to HFO is mainly controlled or limited by the extent of HFO formation, which in turn is governed by the availability of Fe and prevailing Eh-pH conditions. Thus, mineralisation styles and associated geochemical gradients, in particular pyrite abundance, can control the amount of HFO and consequent metalloid attenuation, and these can vary even within the same goldfleld. Furthermore, it was found that there is a mineralogical gradation between ferrihydrite with varying amounts of adsorbed As, amorphous iron arsenates and crystalline iron arsenates, suggesting that the maturity of mine waste is an important factor in As mineralogy. Once dissolved metalloids enter the hydrosphere, dilution is the main control on metalloid attenuation, which is especially pronounced at the inflow of tributaries. Dilution is, therefore, closely related to the size and frequency of these tributaries, which in turn are controlled by the regional topography and climate. Dilution is a considerably less effective attenuation mechanism and anomalous metalloid concentrations from mining related sites can persist for over 10 km downstream. The complex and often inter-dependent controls on metalloid mobility mean that management decisions should carefully consider the specific site geochemistry to minimize economic, health and environmental risks that can not be afforded. On a regional scale, background metalloid flux determines the downstream impact of an anomalous metalloid source upstream. For example, the Bullendale mine is located in a mountainous region, where rapidly eroding slopes expose fresh rock and limit the extent of soil cover and chemical weathering. Consequently, the background As flux is relatively low and As point sources, such as the Bullendale mine, present a significant contribution to the downstream As flux. In contrast, the bedrock at the Blackwater mine has undergone deep chemical weathering, resulting in an increased background mobilisation of As. Thus, the Prohibition mill site discharge, for example, contributes only about 10% to the downstream As flux. This information is relevant to site management decisions because the amount of natural background metalloid mobilisation determines whether site remediation will influence downstream metalloid chemistry on a regional scale.

Thesis (M.S.)--Northwest Missouri State University, 2006. / The full text of the thesis is included in the pdf file. Title from title screen of full text.pdf file (viewed on January 25, 2008) Includes bibliographical references.

Thesis (M. Sc.) (Hons.) -- University of Western Sydney, Nepean, 1998. / Thesis submitted for the degree of Master of Science (Honours) in the University of Western Sydney. Bibliography : p. 100-105.

Thesis(M.Eng.)--University of Wollongong, 2006. / Typescript. Includes bibliographical references: leaf 96-99.