Neste trabalho, foram desenvolvidas antenas planares de micro-ondas multibandas para aplicação em terminais móveis de sistemas de comunicação sem fio. Foi realizado um estudo sobre antenas planares de micro-ondas, com ênfase em técnicas de projeto que possibilitam a operação das mesmas em bandas largas e em múltiplas bandas. A partir dos conhecimentos adquiridos com esse estudo, foram propostas configurações de antenas para terminais móveis de sistemas atuais de telefonia móvel, de WLAN e de WPAN, sistemas esses que têm experimentado nos últimos anos uma grande popularização mundial. Por meio de um procedimento de projeto auxiliado por simulação eletromagnética computacional, as configurações propostas de antenas foram analisadas e otimizadas, visando atender às especificações de projeto estabelecidas para operação nos sistemas mencionados. O desempenho que pode ser obtido com essas configurações de antenas depende de diversos parâmetros geométricos das mesmas, resultando em flexibilidade de projeto para obtenção das bandas de operação desejadas. Protótipos das antenas projetadas foram construídos e caracterizados para validar as configurações propostas de antenas e o procedimento de projeto empregado. Foram desenvolvidas quatro antenas para operação em sistemas de telefonia móvel, de WLAN e de WPAN empregados no Brasil, na Europa e nos EUA: uma antena planar em F-invertido tri-band com configuração original para operação nas bandas dos padrões GSM, DCS e PCS; uma antena planar em F-invertido penta-band com configuração original para operação nas bandas dos padrões GSM, DCS, PCS e UMTS e na banda ISM de 2.400 MHz; duas antenas quad-band, uma delas planar em F-invertido e a outra monopolo impresso com configuração original, para operação nas bandas ISM de 2.400 MHz e de 5.800 MHz e nas bandas de 5.200 MHz e de 5.600 MHz. Os resultados experimentais dos protótipos construídos apresentaram, de modo geral, boa concordância com os resultados fornecidos por simulação e mostraram que as antenas desenvolvidas atenderam às especificações de projeto para elas estabelecidas. Por meio de ambos os resultados experimentais e de simulação, o desempenho das antenas desenvolvidas pôde ser verificado, e demonstrou-se a efetividade do procedimento de projeto adotado. / In this work, multi-band microwave planar antennas for application in mobile terminals of wireless communication systems were developed. A study on microwave planar antennas was performed with emphasis on design techniques that enable their operation in wide bands and multiple bands. From the knowledge gained from this study, antenna configurations for mobile terminals of current mobile telephony, WLAN and WPAN systems, which have experienced in recent years great popularity worldwide, were proposed. By means of a design procedure aided by computer electromagnetic simulation, the proposed antenna configurations were analyzed and optimized in order to meet the design specifications established for operation in the afore mentioned systems. The performance that can be obtained with these antenna configurations depends on their several geometric parameters, resulting in design flexibility for obtaining the desired operation bands. Prototypes of the designed antennas were fabricated and characterized to validate the proposed antenna configurations and the design procedure employed. Four antennas were developed for operation in mobile telephony, WLAN and WPAN systems employed in Brazil, Europe and USA: a tri-band planar inverted-F antenna with novel configuration for operation in GSM, DCS and PCS standard bands; a penta-band planar inverted-F antenna with novel configuration for operation in GSM, DCS, PCS and UMTS standard bands and 2,400 MHz ISM band; two quad-band antennas, one of them planar inverted-F and the other printed monopole with novel configuration, for operation in 2,400 MHz and 5,800 MHz ISM bands and 5,200 MHz and 5,600 MHz bands. The experimental results from the fabricated prototypes exhibited, in general, good agreement with the results provided by simulation and showed that the developed antennas met the specifications established for them. By means of both simulation and experimental results, the performance of the developed antennas could be verified, and the effectiveness of the design procedure adopted was demonstrated.

Neste trabalho, foram desenvolvidas antenas planares de micro-ondas multibandas para aplicação em terminais móveis de sistemas de comunicação sem fio. Foi realizado um estudo sobre antenas planares de micro-ondas, com ênfase em técnicas de projeto que possibilitam a operação das mesmas em bandas largas e em múltiplas bandas. A partir dos conhecimentos adquiridos com esse estudo, foram propostas configurações de antenas para terminais móveis de sistemas atuais de telefonia móvel, de WLAN e de WPAN, sistemas esses que têm experimentado nos últimos anos uma grande popularização mundial. Por meio de um procedimento de projeto auxiliado por simulação eletromagnética computacional, as configurações propostas de antenas foram analisadas e otimizadas, visando atender às especificações de projeto estabelecidas para operação nos sistemas mencionados. O desempenho que pode ser obtido com essas configurações de antenas depende de diversos parâmetros geométricos das mesmas, resultando em flexibilidade de projeto para obtenção das bandas de operação desejadas. Protótipos das antenas projetadas foram construídos e caracterizados para validar as configurações propostas de antenas e o procedimento de projeto empregado. Foram desenvolvidas quatro antenas para operação em sistemas de telefonia móvel, de WLAN e de WPAN empregados no Brasil, na Europa e nos EUA: uma antena planar em F-invertido tri-band com configuração original para operação nas bandas dos padrões GSM, DCS e PCS; uma antena planar em F-invertido penta-band com configuração original para operação nas bandas dos padrões GSM, DCS, PCS e UMTS e na banda ISM de 2.400 MHz; duas antenas quad-band, uma delas planar em F-invertido e a outra monopolo impresso com configuração original, para operação nas bandas ISM de 2.400 MHz e de 5.800 MHz e nas bandas de 5.200 MHz e de 5.600 MHz. Os resultados experimentais dos protótipos construídos apresentaram, de modo geral, boa concordância com os resultados fornecidos por simulação e mostraram que as antenas desenvolvidas atenderam às especificações de projeto para elas estabelecidas. Por meio de ambos os resultados experimentais e de simulação, o desempenho das antenas desenvolvidas pôde ser verificado, e demonstrou-se a efetividade do procedimento de projeto adotado. / In this work, multi-band microwave planar antennas for application in mobile terminals of wireless communication systems were developed. A study on microwave planar antennas was performed with emphasis on design techniques that enable their operation in wide bands and multiple bands. From the knowledge gained from this study, antenna configurations for mobile terminals of current mobile telephony, WLAN and WPAN systems, which have experienced in recent years great popularity worldwide, were proposed. By means of a design procedure aided by computer electromagnetic simulation, the proposed antenna configurations were analyzed and optimized in order to meet the design specifications established for operation in the afore mentioned systems. The performance that can be obtained with these antenna configurations depends on their several geometric parameters, resulting in design flexibility for obtaining the desired operation bands. Prototypes of the designed antennas were fabricated and characterized to validate the proposed antenna configurations and the design procedure employed. Four antennas were developed for operation in mobile telephony, WLAN and WPAN systems employed in Brazil, Europe and USA: a tri-band planar inverted-F antenna with novel configuration for operation in GSM, DCS and PCS standard bands; a penta-band planar inverted-F antenna with novel configuration for operation in GSM, DCS, PCS and UMTS standard bands and 2,400 MHz ISM band; two quad-band antennas, one of them planar inverted-F and the other printed monopole with novel configuration, for operation in 2,400 MHz and 5,800 MHz ISM bands and 5,200 MHz and 5,600 MHz bands. The experimental results from the fabricated prototypes exhibited, in general, good agreement with the results provided by simulation and showed that the developed antennas met the specifications established for them. By means of both simulation and experimental results, the performance of the developed antennas could be verified, and the effectiveness of the design procedure adopted was demonstrated.

Abstract In this thesis, bandwidth (BW) enhanced antennas for mobile terminals and multilayer ceramic packages are presented. The thesis is divided into two parts. In the first part, electrically frequency-tunable mobile terminal antennas have been studied. The first three antennas presented were of a dual-band planar inverted-F type (PIFA) and were tuned to operate in frequency bands appropriate to the GSM850 (824–894 MHz), GSM900 (880–960 MHz), GSM1800 (1710–1880 MHz), GSM1900 (1850–1990 MHz) and UMTS (1920–2170 MHz) cellular telecommunication standards with RF PIN diode switches. The first antenna utilized a frequency-tuning method developed in this thesis. The method was based on an integration of the tuning circuitry into the antenna. The tuning of the second antenna was based on a switchable parasitic antenna element. By combining the two frequency-tuning approaches, a third PIFA could be switched to operate in eight frequency bands. The planar monopole antennas researched were varactor-tunable for digital television signal reception (470–702 MHz) and RF PIN diode switchable dual-band antenna for operation at four cellular bands. The key advantage of the former antenna was a compact size (0.7 cm3), while for the latter one, a tuning circuit was implemented without using separate DC wiring for controlling the switch component. The second part of the thesis is devoted to multilayer ceramic package integrated microwave antennas. In the beginning, the use of a laser micro-machined embedded air cavity was proposed to enable antenna size to impedance bandwidth (BW) trade-off for a microwave microstrip in a multilayer monolithic ceramic media. It was shown that the BW of a 10 GHz antenna fabricated on a low temperature co-fired ceramic (LTCC) substrate could be doubled with this technique. Next, the implementation of a compact surface mountable LTCC antenna package operating near 10 GHz was described. The package was composed of a BW optimized stacked patch microstrip antenna and a wide-band vertical ball grid array (BGA)-via interconnection. Along with the electrical performance optimization, an accurate circuit model describing the antenna structure was presented. Finally, the use of low-sintering temperature non-linear dielectric Barium Strontium Titanate (BST) thick films was demonstrated in a folded slot antenna operating at 3 GHz and frequency-tuned with an integrated BST varactor.

This thesis is a study of multiple access schemes for satellite land mobile systems that provide a domestic or regional service to a large number of small terminals. Three orbit options are studied, namely the geostationary, elliptical (Molniya) and inclined circular orbits. These are investigated for various mobile applications and the choice of the Molniya orbit is justified for a U. K. system. Frequency, Time and Code Division Multiple Access (FDMA, TDMA and CDMA) are studied and their relative merits in the mobile environment are highlighted. A hybrid TDMA/FDMA structure is suggested for a large system. Reservation ALOHA schemes are appraised in a TDMA environment and an adaptive reservation multiple access protocol is proposed and analysed for a wide range of mobile communication traffic profiles. The system can cope with short and long data messages as well as voice calls. Various protocol options are presented and a target system having 100,000 users is considered. Analyses are presented for the steady state of protocols employing pure and slotted ALOHA and for the stabilty of the slotted variant, while simulation techniques were employed to validate the steady state analysis of the slotted ALOHA protocol and to analyse the stability problem of the pure ALOHA version. An innovative technique is put forward to integrate the reservation and the acquisition processes. It employs the geographical spread of the users to form part of the random delay in P-ALOHA. Finally an economic feasibility study is performed for the spacesegment. For costs of capital (r) less than 23 % the discounted payback period is less than the project's lifetime (10 years). At r- 8% the payback period is about 5.6 years, while the internal-rate-of-return is 22.2 %. The net present value at the end of the projects lifetime is £M 70 at r-8%.

The fifth-generation (5G) wireless network has received a lot of attention from both academia and industry with many reported efforts. Multiple-input-multiple-output (MIMO) is the most promising wireless access technology for next-generation networks to provide high spectral and energy efficiency. For handheld devices such as smartphones, 2×2 MIMO antennas are currently employed in 4G systems and it is expected to employ a larger number of elements for 5G mobile terminals. Placing multiple antennas in the limited space of a smartphone PCB poses a significant challenge. Therefore, a new design technique using dual-polarized antenna resonators for 8×8 MIMO configuration is proposed for sub 6 GHz 5G applications. The proposed MIMO configuration could improve the channel capacity, diversity function, and multiplexing gain of the smartphone antenna system which makes it suitable for 5G applications. Different types of new and compact diversity MIMO antennas with Patch, Slot, and Planar inverted F antenna (PIFA) resonators are studied for different candidate bands of sub 6 GHz spectrum such as 2.6, 3.6, and 5.8 GHz. Unlike the reported MIMO antennas, the proposed designs provide full radiation coverage and polarization diversity with sufficient gain and efficiency values supporting different sides of the mainboard. Apart from the sub 6 GHz frequencies, 5G devices are also expected to support the higher bands at the centimeter/millimeter-wave spectrums. Compact antennas can be employed at different portions of a smartphone board to form linear phased arrays. Here, we propose new linear phased arrays with compact elements such as Dipole and Quasi Yagi resonators for 5G smartphones. Compared with the recently reported designs, the proposed phased arrays exhibit satisfactory features such as compact size, wide beam steering, broad bandwidth, end-fire radiation, high gain, and efficiency characteristics. The proposed 5G antennas can provide single-band, multi-band, and broad-band characteristics with reduced mutual coupling function. The fundamental characteristics of the 5G antennas are examined using both simulations and measurements and good agreement is observed. Furthermore, due to compact size and better placement of elements, quite good characteristics are observed in the presence of the user and the smartphone components. These advantages make the proposed antennas highly suitable for use in 5G smartphone applications. / European Union Horizon 2020 Research and Innovation Programme under grant agreement H2020-MSCA-ITN-2016 SECRET-722424

The fifth generation (5G) has developed a lot of interest, and there have been many reported initiatives in both industry and academics. Multiple-input-multiple-output (MIMO) is the most promising wireless access technique for next-generation networks in terms of spectral and energy efficiency (MIMO). In 4G systems, 2-Element MIMO antennas are already used, while 5G mobile terminals for smartphone hand-held devices are projected to use a bigger number of elements. The placement of many antennas in the restricted space of a smartphone PCB is one of the most critical challenges. As a result, for sub-6 GHz 5G applications, a new design technique based on dual-polarised antenna resonators for 6-Element, 8-Element MIMO configuration is proposed. The proposed MIMO design could improve the smartphone antenna system's chan-nel capacity, diversity function, and multiplexing gain, making it appropriate for 5G applica-tions. For distinct prospective bands of the sub-6 GHz spectrum, such as 2.6, 3.6, and 5.8 GHz, different types of novel and compact diversity MIMO antennas using Patch, Slot, and Planar inverted F antenna (PIFA) resonators are examined. Unlike previously reported MIMO antennas, the proposed designs provide full radiation coverage and polarisation diversity, as well as adequate gain and efficiency values to support several mainboard sides. Apart from sub-6 GHz frequencies, 5G devices are projected to support the centimetre/milli-metre wave spectrum's higher bands. To create linear phased arrays, small antennas can be placed at various locations on a smartphone board. For 5G smartphones, we propose novel linear phased arrays with tiny parts like Dipole and Quasi-Yagi resonators. In comparison to previously published designs, the suggested phased arrays have desirable qualities such as compact size, wide beam-steering, broad bandwidth, end-fire radiation, high gain, and efficiency. With a reduced mutual coupling function, the suggested 5G antennas can provide single-band, multi-band, and broad-band characteristics. Both models and measurements are used to an-alyse the fundamental features of 5G antennas, and good agreement is found. Furthermore, in the presence of the user and the smartphone components, good features are seen due to the small size and superior arrangement of elements. Because of these benefits, the sug-gested antennas are well-suited for usage in 5G smartphone applications.