Introduzido na década de 1970, o glifosato figura entre os herbicidas mais consumidos em todo mundo. Devido a características como baixa toxicidade aguda a organismos não-alvo e alta eficiência na eliminação de plantas daninhas, o herbicida se tornou um sucesso de vendas, com um substancial incremento em sua utilização após o desenvolvimento de culturas geneticamente modificadas para tolerar o ingrediente ativo. O elevado consumo do glifosato vem se tornando uma preocupação para diferentes agências ambientais e de saúde. Consequentemente, métodos eficientes para a determinação e quantificação do herbicida se fazem necessários. Na presente dissertação, aprimorou-se um método que utiliza um sistema de análise de injeção sequencial por cromatografia líquida (SIC) com detecção por fluorescência para a determinação de glifosato e seu principal produto de degradação, o ácido aminometilfosfônico (AMPA), em amostras ambientais. Os limites de detecção (LD) e quantificação (LQ) para o glifosato foram 0,10 e 0,33 ԁmol L-1, respectivamente. Já para o AMPA, LD foi de 0,07 µmol L-1 e LQ de 0,22 µmol L-1. O método foi empregado na determinação das espécies em amostras de água fortificadas e gerou valores de recuperação entre 97,2 a 151,5% para o AMPA e 74,6 a 140,5% para o glifosato. Quando empregado em um estudo de adsorção-dessorção, o método foi capaz de produzir valores dos parâmetros de Freundlich e Langmuir comparáveis aos encontrados na literatura. Com qmax = 2,1 ± 0,1 µmol g-1 e KF = 0,53 ± 0,07 µmol1-1/n L1/n g-1, o Latossolo B se mostrou como o solo com maior capacidade de adsorver o glifosato. Em termos de dessorção, o percentual dessorvido ficou abaixo de 55% da quantidade inicialmente adsorvida para as concentrações trabalhadas. / Introduced in the 1970, glyphosate figures among the most used herbicides in the world. Due to characteristics such as low acute toxicity to non-target organisms and high efficiency regarding the elimination of weeds, the herbicide has experienced a huge success in terms of safes. Since genetically modified crops that tolerate the active ingredient have been developed, these safes have continued to increase. Glyphosate\'s high consumption has become a concern to different environmental and health agencies. As a result, efficient methods for the determination of glyphosate and its main metabolite, aminomethylphosphonic acid (AMPA), are necessary. This dissertation describes improvements in a sequential injection chromatography method for the determination of glyphosate and aminomethylphosphonic acid in environmental samples. The limits of detection (LOD) and quantification (LOQ) for glyphosate is 0.10 e 0.33 µmol L-1, respectively. LOD of 0.07 µmol L-1 and LOQ of 0,22 µmol L-1 is registered for AMPA. The method was employed for the determination of both species in spiked water samples and recovery values between 97.2 a 151.5% was obtained for AMPA and between 74.6 a 140.5% for glyphosate. When used in an adsorption-desorption study, the method was capable of generating values for the Freundlich and Langmuir parameters that are similar to those found in the scientific literature. With a qm\" of 2.1 ± 0.1 µmol g-1 and KF = 0.53 ± 0.07 µmol1-1/n L1/n g-1, Latossolo B was the soil sample with the largest glyphosate adsorption capacity. Regarding desorption, the percentages desorbed were beiow 55% of the initial mass of glyphosate adsorbed for the concentrations used.

Introduzido na década de 1970, o glifosato figura entre os herbicidas mais consumidos em todo mundo. Devido a características como baixa toxicidade aguda a organismos não-alvo e alta eficiência na eliminação de plantas daninhas, o herbicida se tornou um sucesso de vendas, com um substancial incremento em sua utilização após o desenvolvimento de culturas geneticamente modificadas para tolerar o ingrediente ativo. O elevado consumo do glifosato vem se tornando uma preocupação para diferentes agências ambientais e de saúde. Consequentemente, métodos eficientes para a determinação e quantificação do herbicida se fazem necessários. Na presente dissertação, aprimorou-se um método que utiliza um sistema de análise de injeção sequencial por cromatografia líquida (SIC) com detecção por fluorescência para a determinação de glifosato e seu principal produto de degradação, o ácido aminometilfosfônico (AMPA), em amostras ambientais. Os limites de detecção (LD) e quantificação (LQ) para o glifosato foram 0,10 e 0,33 ԁmol L-1, respectivamente. Já para o AMPA, LD foi de 0,07 µmol L-1 e LQ de 0,22 µmol L-1. O método foi empregado na determinação das espécies em amostras de água fortificadas e gerou valores de recuperação entre 97,2 a 151,5% para o AMPA e 74,6 a 140,5% para o glifosato. Quando empregado em um estudo de adsorção-dessorção, o método foi capaz de produzir valores dos parâmetros de Freundlich e Langmuir comparáveis aos encontrados na literatura. Com qmax = 2,1 ± 0,1 µmol g-1 e KF = 0,53 ± 0,07 µmol1-1/n L1/n g-1, o Latossolo B se mostrou como o solo com maior capacidade de adsorver o glifosato. Em termos de dessorção, o percentual dessorvido ficou abaixo de 55% da quantidade inicialmente adsorvida para as concentrações trabalhadas. / Introduced in the 1970, glyphosate figures among the most used herbicides in the world. Due to characteristics such as low acute toxicity to non-target organisms and high efficiency regarding the elimination of weeds, the herbicide has experienced a huge success in terms of safes. Since genetically modified crops that tolerate the active ingredient have been developed, these safes have continued to increase. Glyphosate\'s high consumption has become a concern to different environmental and health agencies. As a result, efficient methods for the determination of glyphosate and its main metabolite, aminomethylphosphonic acid (AMPA), are necessary. This dissertation describes improvements in a sequential injection chromatography method for the determination of glyphosate and aminomethylphosphonic acid in environmental samples. The limits of detection (LOD) and quantification (LOQ) for glyphosate is 0.10 e 0.33 µmol L-1, respectively. LOD of 0.07 µmol L-1 and LOQ of 0,22 µmol L-1 is registered for AMPA. The method was employed for the determination of both species in spiked water samples and recovery values between 97.2 a 151.5% was obtained for AMPA and between 74.6 a 140.5% for glyphosate. When used in an adsorption-desorption study, the method was capable of generating values for the Freundlich and Langmuir parameters that are similar to those found in the scientific literature. With a qm\" of 2.1 ± 0.1 µmol g-1 and KF = 0.53 ± 0.07 µmol1-1/n L1/n g-1, Latossolo B was the soil sample with the largest glyphosate adsorption capacity. Regarding desorption, the percentages desorbed were beiow 55% of the initial mass of glyphosate adsorbed for the concentrations used.

In frame work of this diploma thesis, monolithic stationary phases based on hydroxymethylmethacrylate were prepared in fused silica capillaries of 320 μm innerdiameter. Monolithic columns were synthesized by a simple procedure using a polymerization mixture, consisting of a monomer N-(hydroxymethyl) methacrylamide (HMMAA), a croslinking agent ethylene dimethacrylate (EDMA), porogenic solvents butane- 1,4-diol, propane-1-ol and an initiator α,α′-azobisisobutyronitrile (AIBN). Prepared HMMA monolithic columns were utilized for separation of mixtures of biologically active compounds, namely peptides with small number of amino acids. Mechanical strength and specific permeability were determined for selected monolithic columns. Keywords: HPLC, HILIC mechanism, hydroxymethyl methacrylate (HMMA) monolithic columns, amino acid, enkephalins.

High internal phase emulsion polymers (PolyHIPEs) are new generation materials with their high porosity and interconnected open-cell structures and finds applications in areas such as supports for catalytic systems, separation media and tissue engineering scaffolds. Styrene based PolyHIPEs are currently the most popular choice, but solvent compatibility and poor mechanical properties of these materials prevent their applications. Therefore development of new polyHIPEs with desired mechanical and cellular properties is needed to extend the range of applications. The objective of this thesis was to synthesize new polyHIPEs with different mechanical characteristics changing from ductile to elastomeric. For this purpose, acrylic based polyHIPEs with various cellular structure and mechanical characteristics were developed by using stearyl acrylate (SA), isodecyl acrylate (IDA), isobornyl methacrylate (IBMA) and divinylbenzene (DVB). All materials were highly porous (90%) and had open cellular structure with uniform voids in the range of 5.2-12.9 &amp / #956 / m. The PolyHIPEs produced from the monomers of SA and IDA demonstrated elastomeric property and had high ability of recovery when the applied stress is removed. IBMA based polyHIPEs were ductile and demonstrated higher Young&rsquo / s modulus and compression strength than that of conventional styrene based polyHIPEs. Therefore, by varying the composition, it became possible to alter the mechanical properties of polyHIPEs from ductile to elastomeric, without changing the interconnected cellular structures. One of the prepared IDA based polyHIPE was evaluated as stationary phase for capillary electrochromatography for the first time in literature. The column was very efficient in the separation of alkylbenzenes namely thiourea, benzene, toluene, ethylbenzene, propylbenzene and butylbenzene with high column efficiency (up to 200.000 plates/m).

Surfaces that exhibit a gradual change in their chemical and/or physical properties are termed as surface gradients. Based on the changes in properties they are classified either as physical or chemical gradients. Chemical gradients show variations in properties like polarity, charge, functionality concentration and have found potential applications in fields of biology, physics, biosensing, catalysis and separation science. In this dissertation, surface gradients have been prepared using controlled rate infusion (CRI). CRI is a simple method in which a surface gradient is formed by carrying out the infusion of organoalkoxysilane in a time-dependent fashion using a set infusion rate. Depending on concentration of silane, rate of infusion and time of infusion, the gradient profiles on surfaces can be varied and the surface chemistry of the substrate can be altered. Initial work in the dissertation focuses on demonstrating different gradient profiles and selectivity obtained using amine and/ or phenyl functionalized gradient stationary phases on thin layer chromatography (TLC) plates prepared by CRI. The presence of amine and phenyl on the surfaces were confirmed by X-ray Photoelectron Spectroscopy (XPS) and diffuse reflectance spectroscopy, respectively. The change in surface chemistry was demonstrated by changes in the selectivities of water and fat soluble vitamins. After successful preparation and characterization of single and multi-component stationary phase gradients for planar chromatography, single-component gradients were prepared for column chromatography (Silica monolithic columns). Similar to that observed for planar chromatography, the selectivity was evaluated from retention factors and was found to be different for a weak acid/weak base mixture. The results obtained showed the promising approach of using gradient stationary phases in column chromatography. This work was further extended to prepare amine and phenyl multi-component gradients on silica monolithic columns to investigate mixed-mode and synergistic effects. Finally, amine, phenyl and thiol gradients were also prepared on cellulose substrates, particularly water color paper, The goal was to study the formation of functionality gradients on cellulose substrates particularly the interaction between hydroxyl groups on cellulose and silanols and to study the stability of the silanes on the cellulose surface.

En milieu industriel, si l'analyse en ligne d'effluents gazeux à l'aide de la chromatographie en phase gazeuse est actuellement réalisée sans difficultés majeure, l'analyse des liquides reste une des principales problématiques à résoudre. En effet, comparée à une analyse réalisée au laboratoire, l'analyse en ligne d'un échantillon liquide permettrait de s'affranchir de l'étape de prélèvement et de préparation avant injection ainsi que des problèmes de contamination et de représentativité de l'échantillon. Des systèmes d'injection de liquide en ligne sont actuellement disponibles, cependant, des difficultés d'injection liées à la discrimination des analytes sont rencontrées. C'est dans ce contexte qu'une vanne dédiée à l'injection des liquides en ligne a été développée, puis validée en laboratoire, et enfin mise en œuvre sur des applications industrielles pétrolières. Un tout autre enjeu, lié entre autres à la réduction des coûts de maintenance et d'installation, ainsi qu'à la compatibilité de systèmes analytiques destinés à l'industrie et aux micro-pilotes, a orienté des développements instrumentaux vers la miniaturisation des systèmes. Un assemblage de différentes briques technologiques a ensuite été réalisé afin d'évaluer la faisabilité d'un système miniaturisé incorporant la technologie d'injection des liquides en ligne. Finalement et toujours dans ce contexte de miniaturisation, des colonnes monolithiques courtes ont été mises en œuvre en chromatographie en phase gazeuse à haute pression, au laboratoire pour commencer, puis sur des effluents industriels gazeux. Elles ont permis de réaliser des analyses très rapides avec une grande efficacité par unité de longueur tout en pouvant agir sur la sélectivité des colonnes grâce à un contrôle de leurs propriétés de surface / In industry, although on-line analysis of gaseous effluents using gas chromatography is carried out without major difficulty, the analysis of liquids remains problematic and is one of the main issues to be solved. Indeed, compared to an analysis carried out in a laboratory, the on-line analysis of a liquid sample would bypass the steps of sampling and preparation prior to injection and would avoid problems of contamination and representativeness of the sample. Systems for injecting liquids on-line are currently available; however, difficulties are encountered, due to the discrimination of analytes. It is in this context that a valve dedicated to the on-line injection of liquids was developed, validated under laboratory conditions and finally implemented in the oil industry. Another issue, related, amongst other things, to the reduction of maintenance and installation costs, as well as to the compatibility of analytical systems for industry and for micro-pilots, steered instrumental developments towards the miniaturization of systems. Different technological bricks were therefore brought together to assess the feasibility of a miniaturized system involving the technology for on-line injection of liquid. Finally, and still in the context of miniaturization, short monolithic columns were implemented in gaseous phase chromatography at high pressure, first in the laboratory and then on industrial gas effluents. They allowed very fast analyses to be performed which had greater efficiency per unit of length while still being able to act on the selectivity of the columns thanks to the control of their surface properties

Foram desenvolvidas metodologias de cromatografia a líquido de fase reversa baseadas em injeção sequencial (SIC) e em cromatografia a líquido de alta eficiência (HPLC) para determinação de triclosan em amostras de produtos de higiene pessoal e em estudos de adsorção em argilominerais naturais e modificados, visando determinar parâmetros de adsorção de triclosan frente a alguns de seus metabólitos. A determinação de triclosan em enxaguadores bucais foi realizada por SIC com eluição isocrática usando fase móvel constituída por acetonitrila: tampão fosfato de trietilamina 70 mM pH 3,5 na proporção 70:30 (v v-1), obtendo-se limites de detecção e de quantificação de 0,22 e 0,72 mg L-1, respectivamente. Taxas de recuperação entre 96 e 98% foram obtidas da aplicação a amostras reais, sendo que os resultados obtidos pelo método proposto não apresentaram evidências de diferenças estatisticamente significativas em comparação a uma metodologia de referência baseada em HPLC com coluna empacotada. A separação de triclosan (TCS), 2-clorofenol (2-CP), 2,4-diclorofenol (2,4-DCP), 2,4,6-triclorofenol (2,4,6-TCP), 2,3,4-triclorofenol (2,3,4-TCP) e metiltriclosan (MTCS) foi estudada por SIC, obtendo-se a separação de TCS, 2-CP, 2,4-DCP e 2,4,6-TCP com duas etapas de eluição isocrática, a primeira delas com fase móvel 60:40 (v v-1) metanol: tampão acetato de amônio 20 mM (pH 5,5) seguida de eluição com fase móvel 70:30 (v v-1) metanol : tampão acetato de amônio 20 mM (pH 5,5). Nesse caso, os isômeros 2,4,6-TCP e 2,3,4-TCP coeluem. Metiltriclosan, o menos polar desses compostos, pode ser separado de TCS com etapas subseqüentes de eluição. Os métodos foram aplicados para estudar a adsorção de triclosan e seus metabólitos 2,4-DCP, 2,4,6-TCP e metiltriclosan em montmorilonita homoiônica (K+) e modificada com sal de hexadeciltrimetilamônio (HDTMA), observando-se forte adsorção de triclosan e metiltriclosan em comparação a 2-CP, 2,4-DCP e 2,4,6-TCP. A incorporação de HDTMA no argilomineral causou significativo aumento da capacidade de adsorção desses metabólitos, determinada a partir do ajuste dos dados experimentais à equação linearizada de Langmuir, observando-se que a ordem de adsorção é 2,4,6-TCP > 2,4-DCP > 2-CP / Reversed-phase liquid chromatography methodologies based on sequential injection (SIC) and high performance liquid chromatography (HPLC) have been developed for determination of triclosan in samples of personal hygiene products and in studies of adsorption on natural and modified clay minerals aiming to determine kinetic and thermodynamic parameters of adsorption of triclosan in comparison with some of its metabolites. The determination of triclosan in oral rinses with SIC was performed by isocratic elution using a mobile phase of acetonitrile : 70 mM triethylamine phosphate buffer pH 3.5 at the ratio 70:30 (v v-1), obtaining limits of detection and quantification of 0.22 and 0.72 mg L-1, respectively. Recovery rates between 96 and 98 % were obtained from the application to commercial samples, and the results obtained by the proposed method showed no evidence of statistically significant differences compared to the reference methodology based on HPLC with packed column. The separation of triclosan (TCS), 2-chlorophenol (2-CP), 2,4-dichlorophenol (2,4-DCP), 2,4,6-trichlorophenol (2,4,6-TCP), 2,3,4 trichlorophenol (2,3,4-TCP) and methyltriclosan (MTCS) was studied by SIC, resulting in the separation of TCS, 2-CP, 2,4-DCP and 2,4,6-TCP with two isocratic elution steps, the first of them with a mobile phase 60:40 (v v-1) methanol: 20 mM ammonium acetate buffer (pH 5.5) followed by elution with 70:30 (v v-1) mobile phase of methanol : 20 mM ammonium acetate buffer (pH 5.5). In this case, the isomers 2,4,6-TCP and 2,3,4-TCP coeluted. Methyltriclosan, the less polar of these compounds, can be separated from TCS with subsequent elution steps. The methods were applied to study the adsorption of triclosan and its metabolites 2-CP, 2,4-DCP, 2,4,6-TCP and methyltriclosan on homoionic montmorillonite (K+) as well as in hexadecyltrimethylammonium salt (HDTMA) modified montmorillonite, noticing a stronger adsorption of triclosan and methyltriclosan compared with 2-CP, 2,4-DCP and 2,4,6-TCP. Incorporation of HDTMA in the clay mineral caused significant increase in adsorption capacity of these metabolites. This capacity was determined by fitting the experimental data to the linearized Langmuir equation. The adsorption order was 2,4,6-TCP > 2,4-DCP > 2-CP.

A introdução de separações cromatográficas expandiu a aplicabilidade de sistemas de análises em fluxo. No entanto, a seletividade e sensibilidade de procedimentos são restritos devido à escassa disponibilidade de fases estacionárias que operam a baixas pressões. Sendo assim, foram desenvolvidos quatro procedimentos analíticos visando a melhoria destes aspectos. A primeira proposta explorou pioneiramente colunas de núcleo fundido em sistemas de análises por injeção em fluxo. A separação de metil, etil e propil parabenos foi selecionada com aplicação. As eficiências cromatográficas de quatro colunas (C18, RPamida, F5 e fenil-hexil) foram avaliadas criticamente. Acetonitrila e uma solução de ácido fosfórico pH 2,5 foram utilizadas como fase móvel. A fase RP-amida apresentou melhor desempenho com a separação dos três analitos em 8,0 min, com resoluções > 1,72, simetrias de pico < 1,66, LOD entre 0,12 e 0,39 mg L-1, resposta linear até 5,0 mg L-1 (r > 0,996) e CV para altura dos picos < 3,5 % (n=10). O procedimento foi aplicado à determinação de parabenos em produtos de cuidados pessoais e os resultados concordaram com o procedimento de referência a 95% de confiança. Um procedimento envolvendo o acoplamento de extração em fase sólida (SPE) a um sistema de cromatografia por injeção sequencial (SIC) foi proposto para pré-concentração e separação de oito sulfonamidas. A fase estacionária pentafluorofenilpropil foi selecionada após comparação crítica da eficiência apresentada por três colunas de núcleo fundido e duas colunas de fases monolíticas. Acetonitrila e tampão fosfato (pH 5,0) foram utilizados como fase. Fatores de enriquecimento de até 39,2 foram alcançados com volume de amostra de 500 ?L. O procedimento apresentou tempo de análise < 10,5 min, resoluções > 1,83 com simetrias de pico <= 1,52, LOD entre 4,9 e 27 ?g L-1, faixa de resposta linear entre 30,0 e 1000,0 ?g L-1 (r > 0,997) e CV da altura dos picos, 2,9% (n=6). Um procedimento empregando fase estacionária micelar foi desenvolvido para determinação de melamina em leite. A fase móvel foi composta por uma solução aquosa de dodecil sulfato de sódio (SDS) e 1-propanol (92,5:7,5 v/v). O procedimento de preparo de amostra foi implementado em linha pela diluição da amostra com SDS. Resposta linear foi observada entre 2,0 e 6,0 mg L-1 de melamina com LOD estimado em 0,6 mg L-1 e CV da altura dos picos de 2,9% (n=6). Os resultados para diferentes amostras de leite foram concordantes com aqueles obtidos pelo procedimento cromatográfico de referência em um nível de 95% de confiança. Uma estratégia envolvendo pré-concentração on-column de parabenos em um sistema SIC foi proposta. Resposta linear foi observada entre 0,25 e 1,00 ?g mL-1 (r >= 0,999) e LODs estimados entre 40 e 60 ng mL-1. Tempos de retenção e altura dos picos apresentaram CV < 2,1%. Fatores de enriquecimento entre 30,0 e 34,8 foram alcançados. As estratégias propostas são viáveis para melhoria de seletividade e sensibilidade de separações cromatográficas em sistemas de análises em fluxo, além de apresentarem vantagens frente a procedimentos análogos na literatura / The introduction of chromatographic separations expanded the applicability of flow systems. However, selectivity and sensitivity of the procedures are limited due the poor options of stationary phases available for low-pressure. Therefore, four procedures were developed aiming the improvement of these aspects. The first proposal exploited pioneered fused-core columns in a flow injection analysis system. The separation of methyl, ethyl and propel parabens was selected as an application. The chromatographic efficiency of four columns (C18, RP-amide, F5 and fenyl-hexyl) were crítically evaluated. Acetonitrile and a phosphoric acid solution at pH 2.5 were used as mobile phase at different proportions for each column. The RP-amide phase presented the best performance by separating the analytes in 8.0 min with resolution > 1.72, peak symmetry < 1.66, LOD between 0.12-0.39 mg L-1, linear response range up to 5.0 mg L-1 (r > 0.996) and coefficients of variation of peak heights < 3.5% (n=10). The procedure was applied to parabens determination in personal care products and the results agreed with the HPLC reference procedure at the 95% confidence level. A procedure coupling solid phase extraction (SPE) to a sequential injection chromatography (SIC) was proposed for preconcentration and separation of eight sulfonamides. The pentafluorophenylpropyl (F5) phase was selected after a critical comparison of the performance achieved by three fused-core columns and two monolithic columns. Acetonitrile and acetate buffer pH 5.0 were used as mobile phase. Enrichment factors up to 39.2 were achieved with a 500 ?L sample volume. The developed procedure showed analysis time < 10.5 min, resolutions > 1.83 with peak symmetry <= 1.52, LODs between 4.9 and 27 ?g L-1, linear response ranges from 30.0 to 1000.0 ?g L-1 (r > 0.997) and CV of peak heights < 2.9% (n=6). Micelar chromatography was for the first time exploited in SIC and the performance was demonstrated by determination of melamine in milk. Mobile phase was composed by a sodium dodecyl sulfate (SDS) solution and propanol (92.5:7.5). The sample pretreatment procedure was on-line implemented by dilution of the sample with SDS. A linear response was observed within 2.0 and 6.0 mg L-1 of melamine with a LOD estimated at 0.6 mg L-1 and coefficients of variation at 2.9% (n=6). Results for different milk samples agreed with those obtained by high performance liquid chromatography at the 95% confidence level. A procedure involved on-column preconcentration of parabens in a SIC system was based on the injection of relatively high volume of an aqueous sample in a reversed-phase column. After preconcentration, a suitable mobile phase was inserted to perform chromatographic separation (acetonitrile/phosphoric acid pH 2.5 (75:25, v/v)). A linear response was achieved from 0.25 to 1.00 ?g mL-1 (r > 0.999) and LOD estimated within 40 and 80 ng mL-1. Coefficients of variation for retention time and peak heights were below 2.1%. Enrichment factors within 30.0 and 34.8 were achieved. The proposed strategies are feasible for improving selectivity and sensitivity of chromatographic separations in flow analysis systems, besides having advantages compared to similar procedures in the literature

Foram desenvolvidas metodologias de cromatografia a líquido de fase reversa baseadas em injeção sequencial (SIC) e em cromatografia a líquido de alta eficiência (HPLC) para determinação de triclosan em amostras de produtos de higiene pessoal e em estudos de adsorção em argilominerais naturais e modificados, visando determinar parâmetros de adsorção de triclosan frente a alguns de seus metabólitos. A determinação de triclosan em enxaguadores bucais foi realizada por SIC com eluição isocrática usando fase móvel constituída por acetonitrila: tampão fosfato de trietilamina 70 mM pH 3,5 na proporção 70:30 (v v-1), obtendo-se limites de detecção e de quantificação de 0,22 e 0,72 mg L-1, respectivamente. Taxas de recuperação entre 96 e 98% foram obtidas da aplicação a amostras reais, sendo que os resultados obtidos pelo método proposto não apresentaram evidências de diferenças estatisticamente significativas em comparação a uma metodologia de referência baseada em HPLC com coluna empacotada. A separação de triclosan (TCS), 2-clorofenol (2-CP), 2,4-diclorofenol (2,4-DCP), 2,4,6-triclorofenol (2,4,6-TCP), 2,3,4-triclorofenol (2,3,4-TCP) e metiltriclosan (MTCS) foi estudada por SIC, obtendo-se a separação de TCS, 2-CP, 2,4-DCP e 2,4,6-TCP com duas etapas de eluição isocrática, a primeira delas com fase móvel 60:40 (v v-1) metanol: tampão acetato de amônio 20 mM (pH 5,5) seguida de eluição com fase móvel 70:30 (v v-1) metanol : tampão acetato de amônio 20 mM (pH 5,5). Nesse caso, os isômeros 2,4,6-TCP e 2,3,4-TCP coeluem. Metiltriclosan, o menos polar desses compostos, pode ser separado de TCS com etapas subseqüentes de eluição. Os métodos foram aplicados para estudar a adsorção de triclosan e seus metabólitos 2,4-DCP, 2,4,6-TCP e metiltriclosan em montmorilonita homoiônica (K+) e modificada com sal de hexadeciltrimetilamônio (HDTMA), observando-se forte adsorção de triclosan e metiltriclosan em comparação a 2-CP, 2,4-DCP e 2,4,6-TCP. A incorporação de HDTMA no argilomineral causou significativo aumento da capacidade de adsorção desses metabólitos, determinada a partir do ajuste dos dados experimentais à equação linearizada de Langmuir, observando-se que a ordem de adsorção é 2,4,6-TCP > 2,4-DCP > 2-CP / Reversed-phase liquid chromatography methodologies based on sequential injection (SIC) and high performance liquid chromatography (HPLC) have been developed for determination of triclosan in samples of personal hygiene products and in studies of adsorption on natural and modified clay minerals aiming to determine kinetic and thermodynamic parameters of adsorption of triclosan in comparison with some of its metabolites. The determination of triclosan in oral rinses with SIC was performed by isocratic elution using a mobile phase of acetonitrile : 70 mM triethylamine phosphate buffer pH 3.5 at the ratio 70:30 (v v-1), obtaining limits of detection and quantification of 0.22 and 0.72 mg L-1, respectively. Recovery rates between 96 and 98 % were obtained from the application to commercial samples, and the results obtained by the proposed method showed no evidence of statistically significant differences compared to the reference methodology based on HPLC with packed column. The separation of triclosan (TCS), 2-chlorophenol (2-CP), 2,4-dichlorophenol (2,4-DCP), 2,4,6-trichlorophenol (2,4,6-TCP), 2,3,4 trichlorophenol (2,3,4-TCP) and methyltriclosan (MTCS) was studied by SIC, resulting in the separation of TCS, 2-CP, 2,4-DCP and 2,4,6-TCP with two isocratic elution steps, the first of them with a mobile phase 60:40 (v v-1) methanol: 20 mM ammonium acetate buffer (pH 5.5) followed by elution with 70:30 (v v-1) mobile phase of methanol : 20 mM ammonium acetate buffer (pH 5.5). In this case, the isomers 2,4,6-TCP and 2,3,4-TCP coeluted. Methyltriclosan, the less polar of these compounds, can be separated from TCS with subsequent elution steps. The methods were applied to study the adsorption of triclosan and its metabolites 2-CP, 2,4-DCP, 2,4,6-TCP and methyltriclosan on homoionic montmorillonite (K+) as well as in hexadecyltrimethylammonium salt (HDTMA) modified montmorillonite, noticing a stronger adsorption of triclosan and methyltriclosan compared with 2-CP, 2,4-DCP and 2,4,6-TCP. Incorporation of HDTMA in the clay mineral caused significant increase in adsorption capacity of these metabolites. This capacity was determined by fitting the experimental data to the linearized Langmuir equation. The adsorption order was 2,4,6-TCP > 2,4-DCP > 2-CP.

A introdução de separações cromatográficas expandiu a aplicabilidade de sistemas de análises em fluxo. No entanto, a seletividade e sensibilidade de procedimentos são restritos devido à escassa disponibilidade de fases estacionárias que operam a baixas pressões. Sendo assim, foram desenvolvidos quatro procedimentos analíticos visando a melhoria destes aspectos. A primeira proposta explorou pioneiramente colunas de núcleo fundido em sistemas de análises por injeção em fluxo. A separação de metil, etil e propil parabenos foi selecionada com aplicação. As eficiências cromatográficas de quatro colunas (C18, RPamida, F5 e fenil-hexil) foram avaliadas criticamente. Acetonitrila e uma solução de ácido fosfórico pH 2,5 foram utilizadas como fase móvel. A fase RP-amida apresentou melhor desempenho com a separação dos três analitos em 8,0 min, com resoluções > 1,72, simetrias de pico < 1,66, LOD entre 0,12 e 0,39 mg L-1, resposta linear até 5,0 mg L-1 (r > 0,996) e CV para altura dos picos < 3,5 % (n=10). O procedimento foi aplicado à determinação de parabenos em produtos de cuidados pessoais e os resultados concordaram com o procedimento de referência a 95% de confiança. Um procedimento envolvendo o acoplamento de extração em fase sólida (SPE) a um sistema de cromatografia por injeção sequencial (SIC) foi proposto para pré-concentração e separação de oito sulfonamidas. A fase estacionária pentafluorofenilpropil foi selecionada após comparação crítica da eficiência apresentada por três colunas de núcleo fundido e duas colunas de fases monolíticas. Acetonitrila e tampão fosfato (pH 5,0) foram utilizados como fase. Fatores de enriquecimento de até 39,2 foram alcançados com volume de amostra de 500 ?L. O procedimento apresentou tempo de análise < 10,5 min, resoluções > 1,83 com simetrias de pico <= 1,52, LOD entre 4,9 e 27 ?g L-1, faixa de resposta linear entre 30,0 e 1000,0 ?g L-1 (r > 0,997) e CV da altura dos picos, 2,9% (n=6). Um procedimento empregando fase estacionária micelar foi desenvolvido para determinação de melamina em leite. A fase móvel foi composta por uma solução aquosa de dodecil sulfato de sódio (SDS) e 1-propanol (92,5:7,5 v/v). O procedimento de preparo de amostra foi implementado em linha pela diluição da amostra com SDS. Resposta linear foi observada entre 2,0 e 6,0 mg L-1 de melamina com LOD estimado em 0,6 mg L-1 e CV da altura dos picos de 2,9% (n=6). Os resultados para diferentes amostras de leite foram concordantes com aqueles obtidos pelo procedimento cromatográfico de referência em um nível de 95% de confiança. Uma estratégia envolvendo pré-concentração on-column de parabenos em um sistema SIC foi proposta. Resposta linear foi observada entre 0,25 e 1,00 ?g mL-1 (r >= 0,999) e LODs estimados entre 40 e 60 ng mL-1. Tempos de retenção e altura dos picos apresentaram CV < 2,1%. Fatores de enriquecimento entre 30,0 e 34,8 foram alcançados. As estratégias propostas são viáveis para melhoria de seletividade e sensibilidade de separações cromatográficas em sistemas de análises em fluxo, além de apresentarem vantagens frente a procedimentos análogos na literatura / The introduction of chromatographic separations expanded the applicability of flow systems. However, selectivity and sensitivity of the procedures are limited due the poor options of stationary phases available for low-pressure. Therefore, four procedures were developed aiming the improvement of these aspects. The first proposal exploited pioneered fused-core columns in a flow injection analysis system. The separation of methyl, ethyl and propel parabens was selected as an application. The chromatographic efficiency of four columns (C18, RP-amide, F5 and fenyl-hexyl) were crítically evaluated. Acetonitrile and a phosphoric acid solution at pH 2.5 were used as mobile phase at different proportions for each column. The RP-amide phase presented the best performance by separating the analytes in 8.0 min with resolution > 1.72, peak symmetry < 1.66, LOD between 0.12-0.39 mg L-1, linear response range up to 5.0 mg L-1 (r > 0.996) and coefficients of variation of peak heights < 3.5% (n=10). The procedure was applied to parabens determination in personal care products and the results agreed with the HPLC reference procedure at the 95% confidence level. A procedure coupling solid phase extraction (SPE) to a sequential injection chromatography (SIC) was proposed for preconcentration and separation of eight sulfonamides. The pentafluorophenylpropyl (F5) phase was selected after a critical comparison of the performance achieved by three fused-core columns and two monolithic columns. Acetonitrile and acetate buffer pH 5.0 were used as mobile phase. Enrichment factors up to 39.2 were achieved with a 500 ?L sample volume. The developed procedure showed analysis time < 10.5 min, resolutions > 1.83 with peak symmetry <= 1.52, LODs between 4.9 and 27 ?g L-1, linear response ranges from 30.0 to 1000.0 ?g L-1 (r > 0.997) and CV of peak heights < 2.9% (n=6). Micelar chromatography was for the first time exploited in SIC and the performance was demonstrated by determination of melamine in milk. Mobile phase was composed by a sodium dodecyl sulfate (SDS) solution and propanol (92.5:7.5). The sample pretreatment procedure was on-line implemented by dilution of the sample with SDS. A linear response was observed within 2.0 and 6.0 mg L-1 of melamine with a LOD estimated at 0.6 mg L-1 and coefficients of variation at 2.9% (n=6). Results for different milk samples agreed with those obtained by high performance liquid chromatography at the 95% confidence level. A procedure involved on-column preconcentration of parabens in a SIC system was based on the injection of relatively high volume of an aqueous sample in a reversed-phase column. After preconcentration, a suitable mobile phase was inserted to perform chromatographic separation (acetonitrile/phosphoric acid pH 2.5 (75:25, v/v)). A linear response was achieved from 0.25 to 1.00 ?g mL-1 (r > 0.999) and LOD estimated within 40 and 80 ng mL-1. Coefficients of variation for retention time and peak heights were below 2.1%. Enrichment factors within 30.0 and 34.8 were achieved. The proposed strategies are feasible for improving selectivity and sensitivity of chromatographic separations in flow analysis systems, besides having advantages compared to similar procedures in the literature