Most of the today’s concrete structures are older than tenyears, and the need to strengthening existing structures is growing steadily. This is due to various reasons such as degradation due to ageing, environmentally induced degradation, poor initial design or construction and lack of maintenance, to name a few. Among the benefits of strengthening existing structures are; less impacts on the environmental and financial benefits. Therefore, there is a need to find alternative ways to strengthen concrete structures more effectively. For the past decades, several different strengthening methods have been studied. Two examples are externally bonded reinforcement (EBR) and near surface mounted reinforcement (NSM). The outcome of these studies has shown a significant enhancement to the structures. Steel plates and rebar have been used to strengthen concrete structures and have shown good increases in flexural capacity. For this purpose, resins have been used to implement the steel plates and rebar, e.g. shotcrete and epoxy. Due to the weight of steel and its sensitivity to corrosion, new materials have been sought. A promising material for this use is the fiber reinforced polymers (FRP). There are several types of FRP such as, carbon fiber reinforced polymer (CFRP), glass fiber reinforced polymer (GFRP) and aramid fiber reinforced polymer (AFRP). These new material has shown a better performance, due to their light weight, resistance to corrosion,etc. NSM and EBR perform extremely well in practice as long as sufficient anchorage is provided. However, a premature debonding has been observed by several researchers. This report will study an alternative method to reinforce existing concrete structures called “Side Near Surface Mounted Reinforcement (S-NSMR)” in association with a project run by Gabriel Sas at Luleå University of Technology. This is compared to Bottom Near Surface Mounted Reinforcement (B-NSM), which is a well-established method. It is assumed that the fiberutilisation will increase in NSM applied on the side of the beam. If this hypothesis is proven correct, the proposed method will also solve a major constrain in the utilisation of the NSM technique. In certain cases, the bottom of a beam is not fully accessible for strengthening using bottom Applied NSM techniques due to e.g. partition walls or beam-column joints. To test the effect of S-NSMR seven concrete beams, one reference beam with no fiberreinforcement and two sets of three, for S-NSMR and B-NSMR respectively with different CFRP-rebar length, were tested in the laboratory. An analytical calculation has also been carried out. In this thesis, a parametric study is performed with FEM software Atena. The thesis begins with a study of the failure phenomena occurring in the earlier mentioned strengthening method. A benchmark model is then modelled with a good comparison to the experimental results. An idealised model of the steel reinforcement in the concrete beam is used according to Eurocode 2. Material parameters in concrete are calculated according to Atena theory documents. The influence of creep and shrinkage are considered by reducing the elastic modulus of concrete by 25 %, reducing the tensile strength by 50 % and fracture energy accordingly. Thereafter, three additional parameters were chosen to continue the parametric study with Atena, 1) CFRP with E-modulus 160 GPa, 2) two different position in cross-section height of S-NSM and 3) five shorter CFRP-rebar each 100 mm smaller than the previous rebar. The behaviour of the two reinforcing types is then compared. The first parameter is, CFRP with a smaller E-modulus. It could be observed that all beams lost their stiffness, especially after yielding of the steel reinforcement. A small improvement in ductility could also be observed. The utilisation rate of CFRP increased by 13-16% in the case of S-NSM and 18-20% in the case of B-NSM. The second parameter is, different position of CFRP along the height of the beams cross-section in S-NSM beams. The positions of the CFRP was lowered in two steps. In each case an increase in stiffness and a decrease in ductility could be observed. However, the increase of the stiffness was still smaller than the stiffness in the B-NSM, in all cases. The failure mode changed from a ductile (concrete crushing) type to a more brittle kind (peeling-off concrete), due to large flexural cracks at the end of the CFRP-rebar.   The utilisation rate of CFRP-rebar, is decreased in each S-NSM beam except for S-NSM 2 with the height 25 mm. The reduction in the utilisation rate of the CFRP is 7-32 % and in S-NSM 2 with the height H25mm showing an increased in utilisation rate by 7 %. The third is parameter, different length of CFRP-rebar. In the case of S-NSM, the failure mode changed from a ductile failure mode to a brittle failure mode. The utilisation rate decreased with the decrease in CFRP length. In three of five cases, the S-NSM shows a higher ultimate load-displacement relation, and in all five cases the maximum tensile strains in the CFRP were higher in S-NSM than B-NSM. Even though the stiffness in the S-NSM is lower than the B-NSM, it would be more preferable to use the S-NSM than B-NSM, because of its higher ultimate load and lower displacements.

Masonry walls subjected to out-of-plane loading, such as in a seismic event, require reinforcement to improve the ductility of the system. In current masonry construction practice, reinforcement is placed internally and fully grouted. For new construction this can make the wall unjustifiably heavy by not taking advantage of its light, hollow structure. For existing construction, it is difficult to retrofit using this technique. Additionally, the reinforcement is located close to the neutral axis which reduces its effectiveness. Fiber-Reinforced Polymer (FRP) bars, strips and sheets are becoming increasingly popular in construction applications due to their noncorrosive nature and ease of installation. Also, stainless steel bars are used where the structure is exposed to a corrosive environment but have not found wider application for masonry structures. This study is an experimental investigation of the structural performance of masonry walls reinforced with Near-Surface-Mounted (NSM) FRP and stainless steel reinforcement under out-of-plane bending. Additionally, walls with Externally Bonded (EB) FRP sheets were tested. The study simulates retrofitting applications and also proposes the NSM technique for new wall construction, using pre-grooved blocks, in lieu of the conventional method of internal reinforcing and grouting. To accommodate the NSM reinforcement, the grooves in the masonry blocks were aligned with ducts used to anchor the NSM reinforcement in the concrete footing. Seven wall specimens were tested, including walls reinforced with conventional and stainless steel bars, glass-fibre reinforced polymer (GFRP), and carbon-FRP (CFRP) reinforcement. The study demonstrated the feasibility and effectiveness of the NSM technique for new construction. Walls with NSM reinforcement showed a superior performance to those with EB reinforcement. It was shown that increasing the FRP reinforcement ratio may result in a change of failure mode, and as such, the increase in strength may not be proportional to the increase in reinforcement ratio. NSM steel-reinforced walls showed a superior performance in terms of strength, stiffness and the ductility associated with the formation of a plastic hinge at the base. / Thesis (Master, Civil Engineering) -- Queen's University, 2010-05-31 06:24:20.976

Research Doctorate - Doctor of Philosophy (PhD) / Inserting fibre reinforced polymer (FRP) strips into pre-cut grooves in the surface of masonry walls is an emerging technique for the retrofit of unreinforced masonry (URM) structures. This method, known as near surface mounting (NSM), provides significant advantages over externally bonded FRP strips in that it has less of an effect on the aesthetics of a structure and can sustain higher loading before debonding. As this technique is relatively new, few studies into the behaviour of masonry walls strengthened using this technique have been conducted. A combined experimental and numerical program was conducted as part of this research project to study the in-plane shear behaviour of masonry wall panels strengthened with NSM carbon FRP (CFRP) strips. In this project the FRP strips were designed to resist sliding along mortar bed joints and diagonal cracking (through mortar joints and brick units). Both of these failure modes are common to masonry shear walls. Different reinforcement orientations were used, including: vertical; horizontal; and a combination of both. The first stage of the project involved characterising the bond between the FRP and the masonry using experimental pull tests (18 in total). From these tests the bond strength, the critical bond length and the local bond-slip relationship of the debonding interface was determined. The second stage of the project involved conducting diagonal tension/shear tests on masonry panels. A total of four URM wall panels and seven strengthened wall panels were tested. These tests were used to determine: the effectiveness of the reinforcement; the failure modes; the reinforcement mechanisms; and the behaviour of the bond between the masonry and the FRP in the case of a panel. The third stage of the project involved developing a finite element model to help understand the experimental results. The masonry was modelled using the micro-modelling approach, and the FRP was attached to the masonry model using the bond-slip relationships determined from the pull tests. Reinforcement schemes in which vertical FRP strips were used improved the strength and ductility of the masonry wall panels. When only horizontal strips were used to reinforce a wall panel, failure occurred along an un-strengthened bed joint and the increase in strength and ductility was negligible. The vertical reinforcement prevented URM sliding failure by restraining the opening (dilation) of the sliding cracks that developed through the mortar bed joints. The finite element model reproduced the key behaviours observed in the experiments for both the unreinforced and FRP strengthened wall panels. This model would potentially be useful for the development of design equations.

Research Doctorate - Doctor of Philosophy (PhD) / Inserting fibre reinforced polymer (FRP) strips into pre-cut grooves in the surface of masonry walls is an emerging technique for the retrofit of unreinforced masonry (URM) structures. This method, known as near surface mounting (NSM), provides significant advantages over externally bonded FRP strips in that it has less of an effect on the aesthetics of a structure and can sustain higher loading before debonding. As this technique is relatively new, few studies into the behaviour of masonry walls strengthened using this technique have been conducted. A combined experimental and numerical program was conducted as part of this research project to study the in-plane shear behaviour of masonry wall panels strengthened with NSM carbon FRP (CFRP) strips. In this project the FRP strips were designed to resist sliding along mortar bed joints and diagonal cracking (through mortar joints and brick units). Both of these failure modes are common to masonry shear walls. Different reinforcement orientations were used, including: vertical; horizontal; and a combination of both. The first stage of the project involved characterising the bond between the FRP and the masonry using experimental pull tests (18 in total). From these tests the bond strength, the critical bond length and the local bond-slip relationship of the debonding interface was determined. The second stage of the project involved conducting diagonal tension/shear tests on masonry panels. A total of four URM wall panels and seven strengthened wall panels were tested. These tests were used to determine: the effectiveness of the reinforcement; the failure modes; the reinforcement mechanisms; and the behaviour of the bond between the masonry and the FRP in the case of a panel. The third stage of the project involved developing a finite element model to help understand the experimental results. The masonry was modelled using the micro-modelling approach, and the FRP was attached to the masonry model using the bond-slip relationships determined from the pull tests. Reinforcement schemes in which vertical FRP strips were used improved the strength and ductility of the masonry wall panels. When only horizontal strips were used to reinforce a wall panel, failure occurred along an un-strengthened bed joint and the increase in strength and ductility was negligible. The vertical reinforcement prevented URM sliding failure by restraining the opening (dilation) of the sliding cracks that developed through the mortar bed joints. The finite element model reproduced the key behaviours observed in the experiments for both the unreinforced and FRP strengthened wall panels. This model would potentially be useful for the development of design equations.

<div> <p>Due to harsh environmental conditions, the deterioration of prestressed concrete bridge girders is a commonly observed phenomenon in Indiana and much of the Midwest. Concordantly, one widely observed damage scenario is deteriorated end regions of prestressed concrete girders. Damaged or failed expansion joints expose prestressed concrete girder end regions to chloride-laden water, resulting in a corrosive environment in which reinforcement section loss and concrete spalling can occur. For bridges experiencing this type of deterioration, action is needed to ensure the structure remains safe and serviceable. As such, an experimental program was developed to investigate the effectiveness of three repair techniques in restoring the structural behavior of prestressed concrete bridge girders with end region deterioration. The three examined repair techniques are (i) an externally bonded fiber reinforced polymer (FRP) system, (ii) a near-surface-mounted (NSM) FRP system, and (iii) a concrete supplemental diaphragm. Additionally, installation procedures for the three end region repair techniques were developed. Results, conclusions, and recommendations from the experimental program are presented to help advise best practices for implementing end region repair techniques in the field. </p> </div> <br>

No description available.

Στην παρούσα διδακτορική διατριβή αναπτύσσεται μια νέα τεχνική ενίσχυσης υποστυλωμάτων οπλισμένου σκυροδέματος με βάση τη χρήση συνθέτων υλικών, τα οποία αποτελούνται από πλέγματα ινών σε ανόργανη μήτρα (π.χ. κονίαµα µε βάση το τσιμέντο), αποσκοπώντας στην επίλυση προβλημάτων που χαρακτηρίζουν τα Ινοπλισμένα Πολυμερή (ΙΟΠ) σχετικά µε τη χρήση εποξειδικών ρητινών. Τα Ινοπλέγματα σε Ανόργανη Μήτρα (ΙΑΜ) δοκιμάζονται στη μορφή μανδύα µε στόχο την περίσφιγξη και την αύξηση της πλαστιμότητας υποστυλωμάτων παλαιού τύπου, σχεδιασμένων δηλαδή χωρίς τις νέες αντισεισμικές λεπτομέρειες όπλισης. Εξετάζονται διάφορες παράμετροι, που περιλαμβάνουν τη χρήση ράβδων λείων ή με νευρώσεις, την πιθανή ένωση των ράβδων με υπερκάλυψη στον πόδα των υποστυλωμάτων και το μήκος υπερκάλυψης. Έτσι προσδιορίζεται η αποτελεσματικότητα των μανδυών ΙΑΜ και συγκρίνεται με αυτή τον ΙΟΠ ως μέσου περίσφιγξης στις κρίσιμες περιοχές υφισταμένων υποστυλωμάτων για όλες τις περιπτώσεις καμπτικών αστοχιών στην περιοχή της πλαστικής άρθρωσης. Το πειραματικό πρόγραμμα που ακολουθείται για την απόκτηση δεδομένων γύρω από τη συμπεριφορά υποστυλωμάτων οπλισμένου σκυροδέματος, ενισχυμένων με μανδύες ανόργανης (ΙΑΜ) ή οργανικής (ΙΟΠ) μήτρας, περιλαμβάνει συνολικά 28 δοκιμές επί δοκιμίων υποστυλωμάτων δύο τύπων: (α) 15 πρισματικά δοκίμια οπλισμένου σκυροδέματος που δοκιμάζονται σε κεντρική θλίψη και (β) 13 δοκίμια υποστυλωμάτων πλήρους κλίμακας, τα οποία δοκιμάζονται σε ανακυκλιζόμενη κάμψη με σταθερό αξονικό φορτίο. Καταδεικνύεται ότι η αποτελεσµατικότητα των µανδυών ΙΑΜ είναι υψηλή και γενικώς παρόµοια µε αυτή των µανδυών ΙΟΠ για όλες τις περιπτώσεις που εξετάστηκαν. Επιπροσθέτως, τα πειραματικά αποτελέσματα των 13 υποστυλωμάτων πλήρους κλίμακας που υποβλήθηκαν σε ανακυκλιζόμενη κάμψη (με σταθερό αξονικό φορτίο), συμβάλλουν στη διερεύνηση δύο ακόμα “θολών” μέχρι σήμερα πεδίων, όπως: (α) Ο λυγισμός των διαμήκων ράβδων σε περισφιγμένο με μανδύες ΙΑΜ ή ΙΟΠ σκυρόδεμα. Ιδιαίτερη έμφαση δίνεται στη μελέτη της αλληλεπίδρασης μεταξύ του μανδύα ΙΑΜ ή ΙΟΠ και των διαμήκων ράβδων, κατά την έναρξη και εξέλιξη του λυγισμού των τελευταίων. (β) Η αντοχή σε συνάφεια μεταξύ των ενωμένων με παράθεση ράβδων και του περισφιγμένου με μανδύες ΙΑΜ ή ΙΟΠ σκυροδέματος. Ιδιαίτερη έμφαση δίνεται στην πειραματική και αναλυτική μελέτη του μηχανισμού με τον οποίο η περίσφιγξη με μανδύες ΙΟΠ και ΙΑΜ συνεισφέρει στη βελτίωση των συνθηκών συνάφειας μεταξύ ράβδων οπλισμού και σκυροδέματος. Ακόμα στην παρούσα διδακτορική διατριβή διεξάγεται η πρώτη συστηματική μελέτη καμπτικής ενίσχυσης υποστυλωμάτων υπό ανακυκλιζόμενη κάμψη (και σταθερό αξονικό φορτίο) με Πρόσθετους Οπλισμούς νέου τύπου σε Εγκοπές (ΠΟΕ). Εξετάζονται υποστυλώματα που έχουν ενισχυθεί με πρόσθετο οπλισμό ινοπλισμένων πολυμερών (ελάσματα άνθρακα ή ράβδους γυαλιού) καθώς και με ράβδους ανοξείδωτου χάλυβα τοποθετημένων σε εγκοπές. Άλλη μια καινοτομία που εισαγάγει η παρούσα διατριβή είναι ο συνδυασμός του ΠΟΕ με τοπικούς μανδύες ινοπλεγμάτων σε ανόργανη μήτρα (IAM), οι οποίοι αποτελούν ένα εξαιρετικά αποτελεσματικό και πολλά υποσχόμενο σύστημα περίσφιγξης, όπως αναπτύσσεται και περιγράφεται λεπτομερώς στην παρούσα διδακτορική διατριβή. Η έρευνα που υλοποιείται για την απόκτηση δεδομένων γύρω από τη συμπεριφορά υποστυλωμάτων οπλισμένου σκυροδέματος ενισχυμένων σε κάμψη με ΠΟΕ, περιλαμβάνει τη διεξαγωγή 11 δοκιμών επί υποστυλωμάτων πλήρους κλίμακας, τα οποία υποβάλλονται σε ανακυκλιζόμενη κάμψη υπό σταθερό αξονικό φορτίο. . Καταδεικνύεται ότι μέσω ενός κατάλληλου σχεδιασμού, στα πλαίσια του οποίου ο ΠΟΕ συνδυάζεται με τοπικό μανδύα στα άκρα του υποστυλώματος (κορυφή και πόδα), είναι εφικτό η αύξηση της καμπτικής αντίστασης των υποστυλωμάτων να μην συνοδεύεται από μείωση της διαθέσιμης ικανότητας παραμόρφωσης. Τα χρήσιμα πειραματικά ευρήματα από τα ενισχυμένα με ΠΟΕ υποστυλώματα, συμπληρώνονται με την ανάπτυξη ενός αναλυτικού και υπολογιστικού προσομοιώματος, το οποίο έχει διττή συμβολή, καθώς επιτρέπει: (α) την εκτέλεση παραμετρικών αναλύσεων ώστε να μελετηθεί σε βάθος και χωρίς κόπο (πειραματικές δοκιμές) η επίδραση όλων σχεδόν των παραμέτρων, στην καμπτική αντίσταση των ενισχυμένων με ΠΟΕ υποστυλωμάτων. (β) Τη χρήση του ως πολύτιμου υπολογιστικού εργαλείου από το Μηχανικό για το σχεδιασμό καμπτικών ενισχύσεων υποστυλωμάτων με ΠΟΕ και / ή μανδύες συνθέτων υλικών. Η αξία της συμβολής του εν λόγω προσομοιώματος μεγιστοποιείται αν ληφθούν υπόψη ορισμένα χαρακτηριστικά του όπως: (1) Η μείωση των ροπών αντοχής ως προς τους δύο κύριους άξονες (ισχυρός και ασθενής), η οποία οφείλεται στην έντονη σύζευξή τους, για τα ενισχυμένα σε κάμψη υποστυλώματα που υποβάλλονται σε διαξονική κάμψη. (2) Η εφαρμογή ενός τραπεζοειδούς στερεού τάσεων για το σκυρόδεμα σε θλίψη, το οποίο σε σύγκριση με το κλασικό ορθογωνικό στερεό, προσομοιώνει με αρκετά μεγαλύτερη ακρίβεια τον όγκο του σκυροδέματος της θλιβόμενης ζώνης, ιδιαίτερα για τις ενισχυμένες διατομές. (3) Η ταυτόχρονη δράση της εξωτερικής περίσφιγξης με μανδύες συνθέτων υλικών στις ενισχυμένες σε κάμψη διατομές. / The effectiveness of a new structural material, namely Textile-Reinforced Mortar (TRM), was investigated experimentally in this PhD Thesis as a means of confining old-type reinforced concrete (RC) columns with limited capacity due to bar buckling or due to bond failure at lap splice regions. Comparisons with equal stiffness and strength fiber-reinforced polymer (FRP) jackets allow for the evaluation of the effectiveness of TRM versus FRP. Tests were carried out on nearly full scale non-seismically detailed RC columns subjected to cyclic uniaxial flexure under constant axial load. Thirteen cantilever-type specimens with either continuous or lap-spliced deformed longitudinal reinforcement at the floor level were constructed and tested. Experimental results indicated that TRM jacketing is quite effective as a means of increasing the cyclic deformation capacity of old-type RC columns with poor detailing, by delaying bar buckling and by preventing splitting bond failures in columns with lap-spliced bars. Compared with their FRP counterparts, the TRM jackets used in this study were found to be equally effective in terms of increasing both the strength and deformation capacity of the retrofitted columns. From the response of specimens tested in this study, it can be concluded that TRM jacketing is an extremely promising solution for the confinement of RC columns, including poorly detailed ones with or without lap splices in seismic regions. Moreover this PhD Thesis presents the results of a large-scale experimental program aiming to study the behavior of RC columns under simulated seismic loading, strengthened in flexure (of crucial importance in capacity design) with different types and configurations of near-surface mounted (NSM) reinforcing materials. The role of different parameters is examined, by comparison of the lateral load versus displacement response characteristics (peak force, drift ratios, energy dissipation, stiffness). Those parameters were as follows: carbon or glass fiber-reinforced polymers (FRP) versus stainless steel; configuration and amount of NSM reinforcement; confinement via local jacketing; and type of bonding agent (epoxy resin or mortar). The results demonstrate that NSM FRP or stainless steel reinforcement is a viable solution towards enhancing the flexural resistance of reinforced concrete columns subjected to seismic loads. With proper design, which should combine compulsory NSM reinforcement with local jacketing at column ends, it seems that column strength enhancement does not develop at the expense of low deformation capacity.