The cleanliness of high strength low alloy (HSLA) steel was assessed qualitatively and quantitatively. The determination of inclusion type and inclusion morphology were carried out using Selective Potentiostatic Etching by Electrolytic Dissolution (SPEED) method allowing in-situ examination of inclusion morphology by analytical techniques such as SEM/EDS. Inclusion size analysis mainly involved a combination of an analytical technique to provide images of the sample surface and an image analysis system to accurately measure the inclusion size. Four analytical methods were compared in order to evaluate their suitability for subsequent quantitative analysis. It was found that images taken with backscattered electron imaging mode from the scanning electron microscope provides the most accurate representation of inclusion distribution. The various techniques were used to evaluate HSLA steel grades of similar chemistry produced with and without gas shrouding. The results confirmed that with reoxidation minimized by gas shrouding between ladle and tundish, the steel cleanliness was significantly improved.

The cleanliness of high strength low alloy (HSLA) steel was assessed qualitatively and quantitatively. The determination of inclusion type and inclusion morphology were carried out using Selective Potentiostatic Etching by Electrolytic Dissolution (SPEED) method allowing in-situ examination of inclusion morphology by analytical techniques such as SEM/EDS. Inclusion size analysis mainly involved a combination of an analytical technique to provide images of the sample surface and an image analysis system to accurately measure the inclusion size. Four analytical methods were compared in order to evaluate their suitability for subsequent quantitative analysis. It was found that images taken with backscattered electron imaging mode from the scanning electron microscope provides the most accurate representation of inclusion distribution. The various techniques were used to evaluate HSLA steel grades of similar chemistry produced with and without gas shrouding. The results confirmed that with reoxidation minimized by gas shrouding between ladle and tundish, the steel cleanliness was significantly improved.

Neste trabalho foram estudadas 10 corridas em duas usinas siderúrgicas semi-integradas, de aço baixa liga para uso em construção mecânica. Em cada uma das corridas foram retiradas 9 amostras, cada uma ao final de uma etapa do processo de produção: após a remoção de escória na panela, antes da desgaseificação a vácuo, após a desgaseificação a vácuo, após a adição de arame de Al, após a adição de arame de CaSi, após a adição de arame de S, após o fim da turbulência no distribuidor no lingotamento contínuo, 30 minutos após o fim da turbulência no distribuidor no lingotamento contínuo, e 60 minutos após o fim da turbulência no distribuidor no lingotamento contínuo. As amostras foram preparadas metalograficamente e analisadas ao microscópio eletrônico de varredura (MEV) com espectrometria de dispersão de energia (EDS), a fim de se identificar as inclusões presentes no aço em cada etapa do processo. Com isto pode-se fazer a caracterização das inclusões encontradas em cada etapa do processo e a sua classificação segundo a composição química e morfologia. Através da comparação da composição química das inclusões encontradas ao final do refino e no lingotamento contínuo foi possível verificar uma tendência de formação de inclusões de espinélio, e através da composição química das inclusões encontradas no lingotamento contínuo foi possível identificar em quais das corridas estudadas houve a presença de inclusões de aluminatos de cálcio formados no estado líquido. / In the present work it was studied 10 heats in two steelworks, of low alloyed steel for use in mechanical construction. From each heat were taken 9 samples, each one of them at end of one production stage: after deslagging in the ladle; before vacuum degassing; after vacuum degassing; after Al wire addiction; after CaSi wire addiction; after S wire addiction; after the end of tundish turbulence at continuously casting; 30 minutes after the end of tundish turbulence at continuously casting; and 60 minutes after the end of tundish turbulence at continuously casting. Samples were metallographic prepared and analyzed by scanning electronic microscopic (SEM) with energy dispersive X-ray spectroscopy (EDX), in order to identify the inclusions present in steel in each process stage. This allowed the founded inclusions in each process stage to be characterized and classified according to chemical composition and morphology. By comparing founded inclusions chemical composition at end of refining and continuous casting was possible to observe a tendency of formation of spinel inclusions, and by founded inclusions chemical composition in continuous casting was possible to identify in which studied heats there were presence calcium aluminates inclusions formed in the liquid state.

Neste trabalho foram estudadas 10 corridas em duas usinas siderúrgicas semi-integradas, de aço baixa liga para uso em construção mecânica. Em cada uma das corridas foram retiradas 9 amostras, cada uma ao final de uma etapa do processo de produção: após a remoção de escória na panela, antes da desgaseificação a vácuo, após a desgaseificação a vácuo, após a adição de arame de Al, após a adição de arame de CaSi, após a adição de arame de S, após o fim da turbulência no distribuidor no lingotamento contínuo, 30 minutos após o fim da turbulência no distribuidor no lingotamento contínuo, e 60 minutos após o fim da turbulência no distribuidor no lingotamento contínuo. As amostras foram preparadas metalograficamente e analisadas ao microscópio eletrônico de varredura (MEV) com espectrometria de dispersão de energia (EDS), a fim de se identificar as inclusões presentes no aço em cada etapa do processo. Com isto pode-se fazer a caracterização das inclusões encontradas em cada etapa do processo e a sua classificação segundo a composição química e morfologia. Através da comparação da composição química das inclusões encontradas ao final do refino e no lingotamento contínuo foi possível verificar uma tendência de formação de inclusões de espinélio, e através da composição química das inclusões encontradas no lingotamento contínuo foi possível identificar em quais das corridas estudadas houve a presença de inclusões de aluminatos de cálcio formados no estado líquido. / In the present work it was studied 10 heats in two steelworks, of low alloyed steel for use in mechanical construction. From each heat were taken 9 samples, each one of them at end of one production stage: after deslagging in the ladle; before vacuum degassing; after vacuum degassing; after Al wire addiction; after CaSi wire addiction; after S wire addiction; after the end of tundish turbulence at continuously casting; 30 minutes after the end of tundish turbulence at continuously casting; and 60 minutes after the end of tundish turbulence at continuously casting. Samples were metallographic prepared and analyzed by scanning electronic microscopic (SEM) with energy dispersive X-ray spectroscopy (EDX), in order to identify the inclusions present in steel in each process stage. This allowed the founded inclusions in each process stage to be characterized and classified according to chemical composition and morphology. By comparing founded inclusions chemical composition at end of refining and continuous casting was possible to observe a tendency of formation of spinel inclusions, and by founded inclusions chemical composition in continuous casting was possible to identify in which studied heats there were presence calcium aluminates inclusions formed in the liquid state.

The main part of this work has been a literature survey, reviewing scientifical reports forinformation on how steel cleanness is evaluated today, and also how the steel cleanness is related tothe fatigue performance of clean steels.

The Ladle Metallurgy Furnace (LMF) in secondary steelmaking processing allows (1) the adjustment of the chemical composition by ferroalloy addition, (2) temperature control by electrical reheating (3) homogenization of chemical composition by argon stirring (4) desulphurization and (5) control of inclusions produced during steel deoxidation. The solid oxide inclusions not only cause nozzle clogging during the continuous casting process and reduce production efficiency, but they are also harmful to the properties of the steel product. In the case of aluminum killed steel, calcium treatment of steel is typically employed to modify the solid alumina inclusions or magnesium aluminate inclusions to liquid or partially liquid calcium aluminates. Injected calcium in form of calcium wire creates calcium bubbles. A portion of calcium dissolves into the steel and diffuses into the steel bulk. However, during the dissolution process some of the injected calcium reacts, close to the injection plume, with dissolved sulfur and oxygen in the steel to form calcium sulfide and calcium oxide inclusions [1]. During ladle treatment of aluminum killed steel the inclusions which form initially are typically alumina. As the dissolved oxygen content of the steel is reduced to very low levels magnesium may be reduced from the slag and subsequently react with the inclusions resulting in a shift towards higher contents of MgO and formation of magnesium aluminate spinel. Magnesium may originate from the top slag, ferro alloys or refractories. Therefore, magnesium aluminate spinels are almost always present before calcium injection and any consideration of calcium treatment should also consider the modification of spinel in addition to alumina. The current work develops a fundamental kinetic model to describe the evolution of the inclusion population during ladle treatment of aluminum killed steels. The model builds on previous work in the author’s laboratory predicting the kinetics of slag metal reactions during ladle treatment and the transformation of alumina to magnesium aluminate spinel. The model addresses the modification of alumina inclusions by calcium and considers mass transfer of species to the inclusion-steel interface and diffusion within the calcium aluminate phases formed on the inclusion. The dissolution of calcium from calcium bubbles into the steel and formation of oxide and sulfide inclusions at the plume is coupled with the kinetic model for inclusion modification. It is found that rate of supply of calcium to the inclusions controls the overall rate of transformation. The inclusion-steel kinetic model is then coupled with the previously developed steel-slag kinetic model. The coupled inclusion-steel-slag kinetic model is applied to the chemical composition changes in molten steel, slag, and evolution of inclusions in the ladle. The result of calculations is found to agree well with industrial heats for species in the steel as well as inclusions during Ca treatment. The kinetic model is further extended to model the modification of spinel inclusions by calcium treatment. Coupling the model for inclusions modification to a multi component kinetic model for the slag-steel reactions in the ladle furnace allowed prediction of the change of average composition of inclusions which was subsequently verified using plant data from ArcelorMittal Dofasco operations. Good agreement between the experimental and calculated average composition of inclusions was obtained for most of the industrial heats. Finally, a sensitivity analysis of the coupled kinetic model was performed to compare the effect of the different processing conditions including sulphur content, stirring, total oxygen, slag composition and reoxidation, on the evolution path of inclusions. / Thesis / Doctor of Philosophy (PhD)

The vision of this thesis is to study how it is possible to obtain optimised workpieces during metal cutting processes in industry. Specifically, the work is aimed to increase the understanding between the steel characteristics and their link to the chip breaking and tool wear during metal cutting. The emphasis is on the influence of the cleanliness and the characteristics of non-metallic inclusions in the workpiece on the machinability of carburising steel grades. The machinability of a case hardening steel is improved by a M-treatment (additions of Ca). Also, the improved machinability of the M-steels offers an attractive potential to save money which makes it possible to reduce the tooling costs with up to 50%. The improved machinability of Ca-treated steels is correlated to the formation of lubricating slag layers consisting of Ca-enriched sulfide inclusions and oxy-sulfide inclusions, which are formed on the rake face during the machining operation. It is proposed that the formations of slag layers from the workpiece constituents are essential to minimise the chemical degradation of the tool edge due to a contact with the chip. During this process, sulfur minimises the material transfer from the chip flow, whilst Ca-treated impurities have a stabilising effect on the protective deposits made of slag layers. Since there is a remaining industrial need to increase the production rate, whilst maintaining a high quality of the finished parts, the future production will continue to require extreme demands on the quality of workpieces. If the emphasis is focused on the workpiece, it should be possible to obtain a robust manufacturing process. Therefore, the challenge for future steel metallurgists is to develop high performance grades with optimised combined properties. / Syftet med denna avhandling är att studera hur det är möjligt att framställa optimala ämnen för skärande bearbetning i industriell skala. Målsättningen med arbetet är att öka förståelsen för ståls egenskaper och dess inverkan på spånbrytning och slitage av verktyg vid skärande bearbetning. Avhandlingen fokuserar på kopplingen mellan arbetsstyckets renhet och inneslutningskarakteristik och dess inverkan på skärbarhet hos sätthärdningsstål. Skärbarheten hos vanligt sätthärdningsstål kan förbättras markant genom en Ca-behandling, dvs. en så kallad M-behandling. Den förbättrade skärbarheten hos M-stål möjliggör stora kostnadsbesparingar, som uppskattas kunna reducera verktygskostnader med upp till 50%. Den förbättrade skärbarheten hos M-stål beror på bildningen utav tribologiska skikt som är anrikade med (Mn,Ca)S- och (CaO)x-Al2O3-S-slagg. Dessa tribologiska skikt bildas på skärverktygets spånsida under ingrepp vid skärande bearbetning och består utav vissa atomer som överförts från det bearbetade ämnet till skäret. Bildandet av ett skyddande skikt anses nödvändigt för att undvika att verktygets skäregg utsätts för ett kemiskt angrepp i kontaktytan med spånflödet. Svavel anses minimera att rent arbetsmaterial överförs till skärverktyget medans kalcium-berikade inneslutningar hjälper till att bilda ett stabilt och skyddande tribologiskt skikt. Det eviga behovet att öka produktionstakten, utan att för dess skull riskera slutproduktens kvalité ställer stora krav på framtidens material. Med utgångspunkt från arbetsstycken så ska det vara möjligt att uppnå en robust industriell produktion. Utmaningen är därför att utveckla högpresterande stål med en förhöjd kombinerad funktionsegenskap.

<p>The main part of this work has been a literature survey, reviewing scientifical reports forinformation on how steel cleanness is evaluated today, and also how the steel cleanness is related tothe fatigue performance of clean steels.</p>

This report covers a study concerning the methods that are available for determining the cleanness level for steels. No outstanding method is available for rating clean steels, when clean steel is defined as free of fatigue initiating inclusions. Fatigue strength is to a large extent dependant of the biggest inclusion size in the stressed volume. Examples of methods that can be used for finding and testing material for the presence of big inclusions is reported.

Due to growing demands for steel powder properties and continuous evolution of the powder metallurgy (PM) production it is necessary to apply new investigation technics and research applications for quality investigation of the PM products. In addition, it is important to be able to predict the probable maximum size of inclusions. The industrial scale sampling of steel was made in Höganäs AB. The three dimensional (3D) analysis of non-metallic inclusions obtained by electrolytic extraction (EE) method was applied for metal samples taken from liquid steel before water-atomization and after powder forging process. It was demonstrated that the application of the 3D analysis has a perspective and possibility to be used independently or like a reference during 2D analysis of inclusions in powder metallurgy products. The tundish samples have the maximum total number of inclusions but have smaller size of complex inclusion. The size range of inclusions in the ladle and tundish samples is between 1 and 46 μm. The main type of inclusions is spherical (Si-Ca-Al-Mg-O in composition). The powder forged samples have two main types of non-metallic particles: “gray” carbon saturated (10-250 μm) and “bright” clustered oxide particles (1-37 μm with Cr-Si-Mn-Mg-Al-O in composition). The probable maximum size of inclusions was estimated based on a new particle size distribution (PSD) and the standard extreme value distribution (EVD) methods. Both methods predicted that in 1 kg of metal the maximum size of spherical inclusions is &lt; 15 μm in liquid steel samples and the maximum length of “bright” clustered oxide particles is &lt; 63 μm in powder forged samples. However, the prediction of the maximum size by PSD method showed necessity of the further optimization.