91 |
Synchronization and resource allocation in downlink OFDM systemsWu, Fan January 2010 (has links)
The next generation (4G) wireless systems are expected to provide universal personal and multimedia communications with seamless connection and very high rate transmissions and without regard to the users’ mobility and location. OFDM technique is recognized as one of the leading candidates to provide the wireless signalling for 4G systems. The major challenges in downlink multiuser OFDM based 4G systems include the wireless channel, the synchronization and radio resource management. Thus algorithms are required to achieve accurate timing and frequency offset estimation and the efficient utilization of radio resources such as subcarrier, bit and power allocation. The objectives of the thesis are of two fields. Firstly, we presented the frequency offset estimation algorithms for OFDM systems. Building our work upon the classic single user OFDM architecture, we proposed two FFT-based frequency offset estimation algorithms with low computational complexity. The computer simulation results and comparisons show that the proposed algorithms provide smaller error variance than previous well-known algorithm. Secondly, we presented the resource allocation algorithms for OFDM systems. Building our work upon the downlink multiuser OFDM architecture, we aimed to minimize the total transmit power by exploiting the system diversity through the management of subcarrier allocation, adaptive modulation and power allocation. Particularly, we focused on the dynamic resource allocation algorithms for multiuser OFDM system and multiuser MIMO-OFDM system. For the multiuser OFDM system, we proposed a lowiv complexity channel gain difference based subcarrier allocation algorithm. For the multiuser MIMO-OFDM system, we proposed a unit-power based subcarrier allocation algorithm. These proposed algorithms are all combined with the optimal bit allocation algorithm to achieve the minimal total transmit power. The numerical results and comparisons with various conventional nonadaptive and adaptive algorithmic approaches are provided to show that the proposed resource allocation algorithms improve the system efficiencies and performance given that the Quality of Service (QoS) for each user is guaranteed. The simulation work of this project is based on hand written codes in the platform of the MATLAB R2007b.
|
92 |
Evaluation of fourth generation air-interfaces for mobile communicationsVan den Bergh, Ryan Michael 29 May 2008 (has links)
Abstract
Development of the Fourth Generation of mobile communication systems, or 4G, has already
begun in various organizations and research institutions worldwide. There is currently
no single conclusive definition for 4G systems, and the process of 4G standardization will
only begin after the World Radiocommunication Conference in 2007. The purpose of this
report is to provide an objective definition of 4G systems based on user requirements, and
to use this definition to determine an appropriate 4G access network architecture.
By examining the current trends in user requirements, and the methodologies proposed by
different researchers, an objective definition of 4G systems was developed. The definition
states that the purpose of 4G systems is to provide users with the capacity to access any
service at any time at a reasonable cost and at the required levels of quality. There are
two developmental methodologies which are currently being considered to achieve this objective:
first the evolution and convergence of existing systems, including cellular, IT and
broadcasting communication systems, and second, the development of a new 4G access
network capable of providing users with access to advanced services. The primary specification
for this new access network is that it must provide a throughput of 1 Mbps for mobile
users and 1 Gbps for users that are stationary. Other requirements include high spectral
efficiency and high capacity and coverage.
The primary focus of this report is the examination of the second of the above methodologies
by evaluating the performance of candidate 4G air-interface architectures so that a
recommendation could be made as to which of the architectures is the preferred choice as the
core component in a new 4G access network. Orthogonal Frequency Division Multiplexing
(OFDM) modulation is a high performance modulation technique capable of achieving high
levels of spectral efficiency and is widely accepted as the technique most capable of meeting
4G access network requirements. There are two primary access network architectures that
make use of OFDM modulation and could form the core components of a 4G air-interface,
the physical component of a 4G access network. To determine which architecture is the
appropriate choice for 4G systems, a series of simulations were run using realistic models
of a wireless environment. The results of those simulations were analyzed, and it was
determined that, due to the absence of multiple access interference found in MC-CDMA,
OFDMA systems better met the defined requirements for a 4G air-interface. The use of
additional techniques such as radio resource management, multi-antennae technologies and
software defined radios are cited as potential methods for improving both OFDMA and
MC-CDMA performance.
|
93 |
Distributed Digital Radios for Land Mobile Radio ApplicationsNavalekar, Abhijit C 04 January 2010 (has links)
The main objective of this dissertation is to develop the second generation of Distributed Digital Radio (DDR) technology. A DDR II modem provides an integrated voice/data service platform, higher data rates and better throughput performance as compared to a DDR I modem. In order to improve the physical layer performance of DDR modems an analytical framework is first developed to model the Bit Error Rate (BER) performance of Orthogonal Frequency Division Multiplexing over Frequency Modulation (OFDM/FM) systems. The use of OFDM provides a spectrally efficient method of transmitting data over LMR channels. However, the high Peak-to-Average (PAR) of OFDM signals results in either a low Signal-to-Noise Ratio (SNR) at FM receiver or a high non-linear distortion of baseband signal in the FM transmitter. This dissertation presents an analytical framework to highlight the impact of high PAR of OFDM signal on OFDM/FM systems. A novel technique for reduction of PAR of OFDM called Linear Scaling Technique (LST) is developed. The use of LST mitigates the signal distortion occurring in OFDM over FM systems. Another important factor which affects the throughput of LMR networks is the Push-to-Talk (PTT) delay. A PTT delay refers to the delay between the instant when a PTT switch on a conventional LMR radio is keyed/unkeyed and a response is observed at the radio output. It can be separated into a Receive-To-Transmit Switch Interval (RTSI) or a Transmit-To-Receive Switch Interval (TRSI). This dissertation presents the typical RTSI delay values, distributions and their impact on throughput performance of LMR networks. An analytical model is developed to highlight the asymmetric throughput problem and the unintentional denial of service (UDOS) occurring in heterogeneous LMR networks consisting of radios with different PTT delay profiles. This information will be useful in performance and capacity planning of LMR networks in future.
|
94 |
Green networking : analyses of power consumption of real and complex IFFT/FFT used in Next-Generation Networks and optical Orthogonal Frequency Division MultiplexingAl-Obaidi, Sameer Sami Hassan January 2018 (has links)
The Orthogonal Frequency Division Multiplexing is a promising technology for the Next Generation Networks. This technique was selected because of the flexibility for the various parameters, high spectral efficiency, and immunity to ISI. The OFDM technique suffers from significant digital signal processing, especially inside the Inverse/ Fast Fourier Transform IFFT/FFT. This part is used to perform the orthogonality/De-orthogonality between the subcarriers which the important part of the OFDM system. Therefore, it is important to understand the parameter effects on the increase or to decrease the FPGA power consumption for the IFFT/FFT. This thesis is focusing on the FPGA power consumption of the IFFT/FFT uses in the OFDM system. This research finds a various parameters effect on FPGA power of the IFFT/FFT. In addition, investigate the computer software used to measure and analyse the FPGA power consumption of OFDM transceivers, and selects the target hardware used in the computer software. The researched parameters include the number of bits used in calculating the phase factor precision; Cyclic Prefix length effected on IP core IFFT, Subcarrier modulation type, word length width, Real and Complex Value IFFT, IFFT length, and subcarriers sampling frequency. The real value IFFT is proposed in 1987 and implemented in this thesis. These parameters above are discussed by comparing the result between the Real and Complex value IFFT used inside the OFDM system.
|
95 |
EstratÃgias de EstimaÃÃo de Canal para AdaptaÃÃo de Enlace em Sistemas MIMO-OFDM. / Strategies of impact of channel estimation in the link adaption in systems MIMO-OFDMDarlan Cavalcante Moreira 13 November 2006 (has links)
FundaÃÃo de Amparo à Pesquisa do Estado do Cearà / Atualmente a internet à uma ferramenta largamente utilizada e o grande desenvolvimentoe popularidade de tecnologias de acesso sem-fio (wireless) nos levam a um futuro no qual uma conexÃo caracterizada por estar disponÃvel âanytime, anywhereâ, ou seja, a qualquer hora e em qualquer lugar, serà essencial. Tal caracterÃstica à considerada obrigatÃria em sistemas4G (quarta geraÃÃo), mas para uma experiÃncia satisfatÃria para o usuÃrio à necessÃrio que uma conexÃo segura e eficiente esteja disponÃvel. A fim de obter tal eficiÃncia, a comunidade de pesquisa tem gerado algumas soluÃÃes promissoras que obtÃm ganhos significativos no desempenho do sistema, tais como modulaÃÃo e codificaÃÃo adaptativas, codificaÃÃo espaÃo-temporal, mÃltiplas antenas e canais MIMO (Multiple Input Multiple Output ), modulaÃÃo multiportadora, detecÃÃo multiusuÃrio, etc. [1]. Dentre essas soluÃÃes, destaca-se a adaptaÃÃo do sistema, ou seja, o sistema deve estar em constante adaptaÃÃo para obter sempre o melhor desempenho possÃvel para cada situaÃÃo em que se encontra. No entanto, uma importante premissa para a adaptaÃÃo do sistema consiste em conhecer o estado atual em que o sistema se encontra (informaÃÃo sobre o canal de comunicaÃÃo). Para isso diversas tÃcnicas de estimaÃÃo de canal sÃo propostas na literatura, cada uma possuindo vantagens e desvantagens.
Nesse trabalho o impacto da estimaÃÃo de canal na adaptaÃÃo de enlace à analisado atravÃs de simulaÃÃes computacionais1. Em particular, duas tÃcnicas de estimaÃÃo de canal com caracterÃsticas diferentes sÃo analisadas, para alguns cenÃrios especÃficos em um sistema MIMO-OFDM (Multiple Input Multiple Output - Orthogonal Frequency Division Multiplexing ), atravÃs de uma mÃtrica que considera tanto a redundÃncia introduzida para estimar o canal quanto o erro de estimaÃÃo de canal de cada tÃcnica. Os resultados encontrados constituem curvas que podem ser utilizadas para efetuar a adaptaÃÃo de enlace do sistema de maneira mais realista, ou seja, considerando o efeito da estimaÃÃo de canal, alÃm de incluir a prÃpria tÃcnica de estimaÃÃo de canal como um parÃmetro a ser adaptado. / Atualmente a internet à uma ferramenta largamente utilizada e o grande desenvolvimentoe popularidade de tecnologias de acesso sem-fio (wireless) nos levam a um futuro no qual uma conexÃo caracterizada por estar disponÃvel âanytime, anywhereâ, ou seja, a qualquer hora e em qualquer lugar, serà essencial. Tal caracterÃstica à considerada obrigatÃria em sistemas4G (quarta geraÃÃo), mas para uma experiÃncia satisfatÃria para o usuÃrio à necessÃrio que uma conexÃo segura e eficiente esteja disponÃvel. A fim de obter tal eficiÃncia, a comunidade de pesquisa tem gerado algumas soluÃÃes promissoras que obtÃm ganhos significativos no desempenho do sistema, tais como modulaÃÃo e codificaÃÃo adaptativas, codificaÃÃo espaÃo-temporal, mÃltiplas antenas e canais MIMO (Multiple Input Multiple Output ), modulaÃÃo multiportadora, detecÃÃo multiusuÃrio, etc. [1]. Dentre essas soluÃÃes, destaca-se a adaptaÃÃo do sistema, ou seja, o sistema deve estar em constante adaptaÃÃo para obter sempre o melhor desempenho possÃvel para cada situaÃÃo em que se encontra. No entanto, uma importante premissa para a adaptaÃÃo do sistema consiste em conhecer o estado atual em que o sistema se encontra (informaÃÃo sobre o canal de comunicaÃÃo). Para isso diversas tÃcnicas de estimaÃÃo de canal sÃo propostas na literatura, cada uma possuindo vantagens e desvantagens.
Nesse trabalho o impacto da estimaÃÃo de canal na adaptaÃÃo de enlace à analisado atravÃs de simulaÃÃes computacionais1. Em particular, duas tÃcnicas de estimaÃÃo de canal com caracterÃsticas diferentes sÃo analisadas, para alguns cenÃrios especÃficos em um sistema MIMO-OFDM (Multiple Input Multiple Output - Orthogonal Frequency Division Multiplexing ), atravÃs de uma mÃtrica que considera tanto a redundÃncia introduzida para estimar o canal quanto o erro de estimaÃÃo de canal de cada tÃcnica. Os resultados encontrados constituem curvas que podem ser utilizadas para efetuar a adaptaÃÃo de enlace do sistema de maneira mais realista, ou seja, considerando o efeito da estimaÃÃo de canal, alÃm de incluir a prÃpria tÃcnica de estimaÃÃo de canal como um parÃmetro a ser adaptado. / Nowadays the internet is a widely used tool and the great development and popularity of wireless technologies leads us to a future where the connectivity will be characterized as âanywhere, anytimeâ. Such characteristic is considered essential in 4G systems. However, for a satisfactory user experience a secure and efficient connectivity has to be always available. To obtain such efficiency, the research community has generated a number of promising solutions that achieve significative improvements in system performance, such as adaptive modulation and coding, space-time coding, multiple antennas and MIMO (Multiple Input Multiple Output ) channels, multicarrier modulation, multiuser detection, etc. [1]. Among these solutions, the system adaptation is a particularly interesting one, there is, the system must constantly adapt itself to achieve the best performance for each situation. However, one important premise for the system adaptation is the knowledge of the channel state information (CSI). To obtain this knowledge, several channel estimation strategies were proposed in the literature, each one with advantages and disadvantages. In this work we analyze the impact of channel estimation in the link adaptation through computer simulations1. Two channel estimation techniques with different characteristics were analyzed for some specific scenarios in a MIMO-OFDM (Multiple Input Multiple Output - Orthogonal Frequency Division Multiplexing ) system. To perform the analysis it was used a metric that consider the redundancy introduced to estimate the channel and the channel estimation error of each technique. The obtained results constitute curves that can be used to perform link adaptation in a more realistic way, that is, considering the effect of channel estimation. Besides, it is shown that even the choice of the channel estimation strategy can be an adaptable parameter so that the most adequate channel estimation strategy for each system state is used. / Nowadays the internet is a widely used tool and the great development and popularity of wireless technologies leads us to a future where the connectivity will be characterized as âanywhere, anytimeâ. Such characteristic is considered essential in 4G systems. However, for a satisfactory user experience a secure and efficient connectivity has to be always available. To obtain such efficiency, the research community has generated a number of promising solutions that achieve significative improvements in system performance, such as adaptive modulation and coding, space-time coding, multiple antennas and MIMO (Multiple Input Multiple Output ) channels, multicarrier modulation, multiuser detection, etc. [1]. Among these solutions, the system adaptation is a particularly interesting one, there is, the system must constantly adapt itself to achieve the best performance for each situation. However, one important premise for the system adaptation is the knowledge of the channel state information (CSI). To obtain this knowledge, several channel estimation strategies were proposed in the literature, each one with advantages and disadvantages. In this work we analyze the impact of channel estimation in the link adaptation through computer simulations1. Two channel estimation techniques with different characteristics were analyzed for some specific scenarios in a MIMO-OFDM (Multiple Input Multiple Output - Orthogonal Frequency Division Multiplexing ) system. To perform the analysis it was used a metric that consider the redundancy introduced to estimate the channel and the channel estimation error of each technique. The obtained results constitute curves that can be used to perform link adaptation in a more realistic way, that is, considering the effect of channel estimation. Besides, it is shown that even the choice of the channel estimation strategy can be an adaptable parameter so that the most adequate channel estimation strategy for each system state is used.
|
96 |
Iterative Receiver for MIMO-OFDM System with ICI Cancellation and Channel EstimationLi, Rui January 2008 (has links)
Master of Engineering by Research / As a multi-carrier modulation scheme, Orthogonal Frequency Division Multiplexing (OFDM) technique can achieve high data rate in frequency-selective fading channels by splitting a broadband signal into a number of narrowband signals over a number of subcarriers, where each subcarrier is more robust to multipath. The wireless communication system with multiple antennas at both the transmitter and receiver, known as multiple-input multiple-output (MIMO) system, achieves high capacity by transmitting independent information over different antennas simultaneously. The combination of OFDM with multiple antennas has been considered as one of most promising techniques for future wireless communication systems. The challenge in the detection of a space-time signal is to design a low-complexity detector, which can efficiently remove interference resulted from channel variations and approach the interference-free bound. The application of iterative parallel interference canceller (PIC) with joint detection and decoding has been a promising approach. However, the decision statistics of a linear PIC is biased toward the decision boundary after the first cancellation stage. In this thesis, we employ an iterative receiver with a decoder metric, which considerably reduces the bias effect in the second iteration, which is critical for the performance of the iterative algorithm. Channel state information is required in a MIMO-OFDM system signal detection at the receiver. Its accuracy directly affects the overall performance of MIMO-OFDM systems. In order to estimate the channel in high-delay-spread environments, pilot symbols should be inserted among subcarriers before transmission. To estimate the channel over all the subcarriers, various types of interpolators can be used. In this thesis, a linear interpolator and a trigonometric interpolator are compared. Then we propose a new interpolator called the multi-tap method, which has a much better system performance. In MIMO-OFDM systems, the time-varying fading channels can destroy the orthogonality of subcarriers. This causes serious intercarrier interference (ICI), thus leading to significant system performance degradation, which becomes more severe as the normalized Doppler frequency increases. In this thesis, we propose a low-complexity iterative receiver with joint frequency- domain ICI cancellation and pilot-assisted channel estimation to minimize the effect of time-varying fading channels. At the first stage of receiver, the interference between adjacent subcarriers is subtracted from received OFDM symbols. The parallel interference cancellation detection with decision statistics combining (DSC) is then performed to suppress the interference from other antennas. By restricting the interference to a limited number of neighboring subcarriers, the computational complexity of the proposed receiver can be significantly reduced. In order to construct the time variant channel matrix in the frequency domain, channel estimation is required. However, an accurate estimation requiring complete knowledge of channel time variations for each block, cannot be obtained. For time- varying frequency-selective fading channels, the placement of pilot tones also has a significant impact on the quality of the channel estimates. Under the assumption that channel variations can be approximated by a linear model, we can derive channel state information (CSI) in the frequency domain and estimate time-domain channel parameters. In this thesis, an iterative low-complexity channel estimation method is proposed to improve the system performance. Pilot symbols are inserted in the transmitted OFDM symbols to mitigate the effect of ICI and the channel estimates are used to update the results of both the frequency domain equalizer and the PICDSC detector in each iteration. The complexity of this algorithm can be reduced because the matrices are precalculated and stored in the receiver when the placement of pilots symbols is fixed in OFDM symbols before transmission. Finally, simulation results show that the proposed MIMO-OFDM iterative receiver can effectively mitigate the effect of ICI and approach the ICI-free performance over time-varying frequency-selective fading channels.
|
97 |
Techniques in Secure Chaos Communication.Lau, Yuu Seng, lauje@rocketmail.com January 2006 (has links)
In today's climate of increased criminal attacks on the privacy of personal or confidential data over digital communication systems, a more secure physical communication link is required. Chaotic signals which have bifurcation behavior (depending on some initial condition) can readily be exploited to enhance the security of communication systems. A chaotic generator produces disordered sequences that provide very good auto- and cross- correlation properties similar to those of random white noise. This would be an important feature in multiple access environments. These sequences are used to scramble data in spread spectrum systems as they can produce low co-channel interference, hence improve the system capacity and performance. The chaotic signal can be created from only a single mathematical relationship and is neither restricted in length nor is repetitive/ cyclic. On the other hand, with the progress in digital signal processing and digital hardware, there has been an increased interest in using adaptive algorithms to improve the performance of digital systems. Adaptive algorithms provide the system with the ability to self-adjust its coefficients according to the signal condition, and can be used with linear or non-linear systems; hence, they might find application in chaos communication. There has been a lot of literature that proposed the use of LMS adaptive algorithm in the communication arena for a variety of applications such as (but not limited to): channel estimation, channel equalization, demodulation, de-noising, and beamforming. In this thesis, we conducted a study on the application of chaos theory in communication systems as well as the application of adaptive algorithms in chaos communication. The First Part of the thesis tackled the application of chaos theory in com- munication. We examined different types of communication techniques utilizing chaos theory. In particular, we considered chaos shift keying (CSK) and mod- ified kind of logistic map. Then, we applied space-time processing and eigen- beamforming technique to enhance the performance of chaos communication. Following on, we conducted a study on CSK and Chaos-CDMA in conjunction with multi-carrier modulation (MCM) techniques such as OFDM (FFT/ IFFT) and wavelet-OFDM. In the Second Part of the thesis, we tried to apply adaptivity to chaos com- munication. Initially, we presented a study of multi-user detection utilizing an adaptive algorithm in a chaotic CDMA multi-user environment, followed by a study of adaptive beamforming and modified weight-vector adaptive beam- forming over CSK communication. At last, a study of modified time-varying adaptive filtering is presented and a conventional adaptive filtering technique is applied in chaotic signal environment. Twelve papers have been published during the PhD candidature, include two journal papers and ten refereed conference papers.
|
98 |
Implementation of an IEEE 802.11a transmitter in VHDL for Altera Stratix II FPGABrännström, Johannes January 2006 (has links)
<p>The fast growth of wireless local area networks today has opened up a whole new market for wireless solutions. Released in 1999, the IEEE 802.11a is a standard for high-speed wireless data transfer that much of modern Wireless Local Area Network technology is based on.</p><p>This project has been about implementing the transmitter part of the 802.11a physical layer in VHDL to run on the Altera Stratix II FPGA. Special consideration was taken to divide the system into parts based on sample rate. This report contains a brief introduction to Orthogonal Frequency Division Multiplexing and to the IEEE 802.11a physical layer as well as a description of the implemented system.</p>
|
99 |
Efficient WiMAX Receiver Implementation on a Programmable Baseband ProcessorAxell, Christian, Brogsten, Mikael January 2006 (has links)
<p>WiMAX provides broadband wireless access and uses OFDM as the underlying modulation technique. In an OFDM based wireless communication system, the channel will distort the transmitted signal and the performance is seriously degraded by synchronization mismatches between the transmitter and receiver. Therefore such systems require extensive digital signal processing of the received signal for retrieval of the transmitted information.</p><p>In this master thesis, parts of an IEEE 802.16d (WiMAX) receiver have been implemented on a programmable baseband processor. The implemented parts constitute baseband algorithms which compensates for the effects from the channel and synchronization errors. The processor has a new innovative architecture with an instruction set optimized for baseband applications.</p><p>This report includes theory behind the baseband algorithms as well as a presentation of how they are implemented on the processor. An impartial evaluation of the processor performance with respect to the algorithms used in the reference model is also presented in the report.</p>
|
100 |
The influence of the dispersionmap on optical OFDM transmissionsForozesh, Kamyar January 2010 (has links)
<p>Fiber-optic networks are an integral part of todays digital communication system. In these networks, distances of typically 400 km to 6000 km are linked together, and information is transfered at extremely high data rates. As the demands for capacity increases, finding new methods for cost effective long-haul transmission systems that can be used to increase the capacity becomes of high interest. In this work Orthogonal Frequency Division Multiplexing (OFDM), which is a standard digital modulation format in many wireless communication systems, for instance the IEEE 802.11n, is adapted to the optical domain and used for data transmission. The advantage of OFDM in the optical domain is that it transforms a high data rate stream into many simultaneously low bit rate streams that are efficiently frequency multiplexed. By doing so high spectral efficiency is achieved and many of the impairments encountered in high data rate transmissions are avoided. The disadvantage is however, that OFDM has inherently a high peak-to-average power ratio. As a result, OFDM suffers from nonlinearities occurring along the transmission line. The low nonlinear tolerance of OFDM in fiber optic applications restricts the feasible transmission distance. The goal of this work is to assess the suitability of OFDM in fiber-optic communications</p>
|
Page generated in 0.0441 seconds