<p>Nanomaterials have attracted great interest in recent years, and are now also being considered for battery applications. Reducing the particle size of some electrode materials can increase battery performance considerably, especially with regard to capacity, power and rate capability. This thesis presents a study focused on the performance of such a material, vanadium oxide nanotubes, as cathode material for rechargeable lithium batteries.</p><p>These nanotubes were synthesized by a sol-gel process followed by hydrothermal treatment. They consist of vanadium oxide layers separated by structure-directing agents, normally amines or metal ions, e.g., Na⁺, Ca²⁺, Mn²⁺ and Cu²⁺. The layers are arranged in a scroll-like manner, allowing the interlayer structure to expand and contract, depending on the size of the embedded guest. This tubular form of vanadium oxide was able to insert lithium ions reversibly, making it a candidate cathode material. The structural and electrochemical response to lithium ion insertion was carefully studied to define optimal performance criteria and probe the lithium insertion mechanism. This was done using several characterization techniques, including X-ray diffraction, a variety of spectroscopic methods and electrochemical testing. Galvanostatic measurements show that the material can be charged and discharged reversibly for >100 cycles with a capacity of 150-200 mAh/g. The electrochemical performance is, however, dependent on the electrode film preparation technique, the choice of salt in the electrolyte and the nature of the embedded guest. Results from photoelectron spectroscopy, and soft X-ray emission and absorption spectroscopy confirm that vanadium is reduced during lithium insertion and that three oxidation states (V⁵⁺, V⁴⁺and V³⁺) co-exist at potentials below 2.0 V. <i>In situ</i> X-ray diffraction, performed during potential stepping, identifies two separate processes during lithium insertion: a fast decrease of the interlayer distance followed by a slow two-dimensional relaxation of the vanadium oxide layers. </p>

Future energy systems based on hydrogen as energy carrier require reliable ways for storing hydrogen gas in safe, clean and efficient ways. Metal hydrides absorb hydrogen gas reversibly, making them suitable for storage applications. Investigations of the crystal structures of these materials contribute to an understanding of the factors which can influence the absorption. Three systems, Ti3Sn-D, Nb4MSi-D (M=Co or Ni) and Pd-Ni-P, have been investigated in this thesis. Various solid state synthesis techniques have been used for sample preparation. The crystal structures have been studied using x-ray and neutron diffraction techniques. Three metal hydride phases were found in the Ti3Sn-D system upon hydrogenation. Deuterium occupies titanium octahedra and the applied deuterium pressure induces the phase transitions. The distances between the deuterium atoms increase from 2.47 Å in orthorhombic Ti3SnD0.80 to 4.17 Å in cubic Ti3SnD. The Nb4MSi-D system (M=Co or Ni) readily absorbs deuterium at room temperature and 90 kPa deuterium pressure to give a deuterium content of Nb4MSiD~2.5. Two interstitial voids, both coordinated by four niobium atoms arranged in a tetrahedral configuration, accommodate deuterium atoms. Two ternary phases and a solid solution of nickel in Pd3P have been synthesised and the crystal structures determined. PdNi2P is orthorhombic and crystallises in the MgCuAl2-type structure: an ordered derivative of the Re3B-type structure. Pd8Ni31P16 is a tetragonal high-temperature phase stable at 700°C with 110 atoms in the unit cell. Pd2.7Ni0.3P0.94 has the cementite-type structure with mixed occupancy of palladium and nickel at one of the two non-equivalent crystallographic metal positions.

Due to the small dimensions, nanoparticles and materials consisting of nano-sized building blocks exhibit unique — mostly superior — properties, well differing from their bulk counterpart. Most of the novel properties of nanoparticles (and nanomaterials) are size-dependent, while the majority of the common gasphase methods used for generation of nanopowders result in different, usually wide, size-dispersions. Further understanding of the fundamental processes leading to particle formation is therefore required, leading to better control of size and distribution of the nanoparticles, thus allowing engineering of the desired properties for both nanoparticles and nanomaterials. In this present thesis, nanoparticles were produced by two different gasphase techniques activated by lasers, namely laser chemical vapor deposition (LCVD) and pulsed laser ablation (PLA). Optical emission spectroscopy (OES) was performed on thermal (blackbody-like) radiation originating from laser-excited particles during LCVD and coupled to measured size-distributions. In-situ monitoring of size-distributions by a differential mobility analyzer (DMA) was employed during PLA. In addition, deposited nanoparticles were characterized by a variety of standard techniques. Different cooling mechanisms of the laser-excited gasphase particles were identified based on temperature and emitted intensity data extracted from OES measurements. The strong evaporation at elevated temperatures also allowed direct size manipulation of the particles. By monitoring the intensity of the emitted thermal radiation and the scattered laser line, strong indications about the so called coagulation limit, where a broadening of the size-distribution occurred, was obtained. The DMA monitoring, supported by modeling, gave information about different mechanisms (thermal and photochemical) of the ablation process, and particle condensation well below the ablation threshold was also found.

The development of more advanced materials forms the basis of technological progress. One group of fascinating compounds with many potential applications in spintronic devices are the mixed-valence perovskite manganites. These have attracted considerable interest during the last decade through their very large magnetoresistance near the Curie Temperature. Although the properties of a material determinie any application, the development of reliable and flexible synthesis methods is crucial, as is the understanding of these methods. Knowledge of how different materials are formed is also of general importance in tailoring new materials. The aim of this project has therefore been not only to develop a new synthesis route, but also to understand the mechanisms involved. This thesis describes the synthesis and characterization of a novel manganese alkoxide and its use in sol–gel processing of magnetoresistive perovskite manganites. In searching for a soluble manganese alkoxide for sol–gel processing, we found that the methoxy-ethoxide, [Mn19O12(moe)14(moeH)10]·moeH, has a high solubility in appropriate organic solvents. Being 1.65 nm across, it is one of the largest alkoxides reported; it is also of interest because of its (for oxo-alkoxides) rare planar structure. After mixing with La, Nd, Ca, Sr, and Ba methoxy-ethoxides, [Mn19O12(moe)14(moeH)10]·moeH was used in the first purely alkoxide based sol–gel processing of perovskites manganites. The phase evolution on heating xerogel powders to 1000°C was studied, and thin films were prepared by spin-coating. It was found that the easily oxidised Mn-alkoxide facilitates the formation of high oxygen-excess modifications of the perovskites. The reactive precursor system yields fully hydrolysed gels almost without organic residues, but the gel absorbs CO2 from the air, leading to carbonate formation. The carbonate decomposition is the limiting step in oxide formation. Transport measurements of La0.67Ca0.33MnO3 films on LaAlO3 substrate show that all-alkoxide sol–gel derived films can compete with PLD films in terms of quality of epitaxy and transport. The somewhat different behaviour of the sol–gel derived films compared to PLD films is attributed to differences in morphology and oxygen stoichiometry.

Nanomaterials have attracted great interest in recent years, and are now also being considered for battery applications. Reducing the particle size of some electrode materials can increase battery performance considerably, especially with regard to capacity, power and rate capability. This thesis presents a study focused on the performance of such a material, vanadium oxide nanotubes, as cathode material for rechargeable lithium batteries. These nanotubes were synthesized by a sol-gel process followed by hydrothermal treatment. They consist of vanadium oxide layers separated by structure-directing agents, normally amines or metal ions, e.g., Na+, Ca2+, Mn2+ and Cu2+. The layers are arranged in a scroll-like manner, allowing the interlayer structure to expand and contract, depending on the size of the embedded guest. This tubular form of vanadium oxide was able to insert lithium ions reversibly, making it a candidate cathode material. The structural and electrochemical response to lithium ion insertion was carefully studied to define optimal performance criteria and probe the lithium insertion mechanism. This was done using several characterization techniques, including X-ray diffraction, a variety of spectroscopic methods and electrochemical testing. Galvanostatic measurements show that the material can be charged and discharged reversibly for &gt;100 cycles with a capacity of 150-200 mAh/g. The electrochemical performance is, however, dependent on the electrode film preparation technique, the choice of salt in the electrolyte and the nature of the embedded guest. Results from photoelectron spectroscopy, and soft X-ray emission and absorption spectroscopy confirm that vanadium is reduced during lithium insertion and that three oxidation states (V5+, V4+ and V3+) co-exist at potentials below 2.0 V. In situ X-ray diffraction, performed during potential stepping, identifies two separate processes during lithium insertion: a fast decrease of the interlayer distance followed by a slow two-dimensional relaxation of the vanadium oxide layers.

This thesis describes the synthesis and radiohalogenation of compounds of potential use for tumor targeting. The first section describes the synthesis and radioiodination of DNA intercalating compounds. The compounds are derivatives of 9-aminoacridine, and the anthracyclins daunorubicin and doxorubicin. The precursor compounds were labeled with 125I (T1/2 = 60 days), which is an Auger emitting nuclide. 125I decaying in the close vicinity of DNA is known to have a much higher cell killing effect than 125I decaying in the cytoplasm and some of the labeled compounds prepared in this thesis are currently being tested for use in targeted radionuclide therapy for cancer. The second section describes the radiobromination of closo-carboranes by subjecting the corresponding iodinated compounds to palladium-catalyzed halogen exchange using [76Br]bromide. The 76Br isotope (T1/2 = 16.2 h) is a positron emitting nuclide that is suitable for PET studies. Via the halogen exchange reaction good to excellent radiochemical yields of radiobrominated closo-carboranes were obtained. The results of the present study may prove to be applicable to pharmacokinetic studies of carboranes and their derivatives. The third and final section describes the indirect radiobromination of the trastuzumab anti-HER2 monoclonal antibody and of the anti-HER2 Affibody by means of an “one-pot” procedure using N-succinimidyl-5-(tributylstannyl)-3-pyridinecarboxylate (SPC) and ((4-hydroxyphenyl)ethyl))maleimide (HPEM), respectively. It was found that SPC and HPEM can be efficiently radiobrominated and thereafter coupled to the antibody and Affibody, respectively. The labeled proteins retained their capacity to bind specifically to HER2 expressing SKOV-3 cells in vitro. Application of this method to 76Br might enable the use of PET in the detection of HER2 expression in breast, ovarian, and urinary bladder carcinomas.

The copper-binding ability of the prion protein may be closely connected to its function. Identifying the exact function of the prion protein can clarify the underlying mechanism in prion diseases. In this work, the copper-binding octapeptide region in the human prion protein has been studied. The structural characteristics of the binding site are examined by quantum chemical structural optimization. The calculations aim at identifying a substitute for copper(II) to be used in NMR-spectroscopic studies of the copper-binding region. The dynamical and structural features of the peptide region are investigated in molecular dynamics simulations. Aspects of importance in the development of model systems in molecular dynamics simulation are addressed. / QC 20101220

This thesis reports on the development of low-temperature processes for transition metal carbide and MAX-phase thin film growth. Magnetron sputtering and evaporation, far from thermodynamical equilibrium, have been utilised to engineer the properties of the films by physical and chemical control. Deposition of W, W2C and β-WC1-x films with controlled microstructure, from nanocrystalline to epitaxial, is shown in the W-C system down to 100 oC. W films with upto 20 at% C exhibited an extreme solid-solution hardening effect, with a nanoindentation hardness maximum of 35 GPa. Furthermore, the design of epitaxial ternary carbide films is demonstrated in the Ti1-xVxCy system in the form of controlled unit-cell parameters, strain-free films with a perfect match to the substrate, and ternary epitaxial gradient films. Moreover, phase stabilisation and pseudomorphic growth can be tuned in (Nb,Mo)C and (Ti,W)C films. The results obtained can be used for example to optimise electrical contacts in SiC high-power semiconductor devices. A large part of this thesis focuses on the deposition of MAX-phases. These compounds constitute a family of thermally stable nanolaminates with composition Mn+1AXn, n=1, 2 or 3, where M is an early transition metal, A is generally a group 13-14 element, and X is C or N. They show a combination of typical ceramic and metallic properties and are also machinable by virtue of the unique deformation behaviour observed only in laminates. So far, the MAX-phases have almost exclusively been prepared by high-temperature sintering and studied in bulk form. However, this thesis establishes a patented seed layer approach for successful MAX-phase thin film depositions down to 750 oC. For the first time, single-phase and epitaxial films of Ti3SiC2, Ti3AlC2 and Ti2AlC have been grown. The method has also been used to synthesise a new MAX-phase, Ti4SiC3. In addition, two previously unreported intergrown MAX-type structures are presented, Ti5Si2C3 and Ti7Si2C5. Combined theoretical and experimental results show the possibility to deposit films with very low bulk resistivity and designed mechanical properties. Furthermore, the demonstration of MAX-phase and carbide multilayer films paves the way for macrostructure engineering, for example, in coatings for low-friction or wear applications.

<p>Self-oscillating behaviour in alkaline Cu(II)-lactate and -tartrate systems has been investigated by in-situ pH and confocal Raman spectroscopy measurements. Formation of Cu(II)-lactate and -tartrate complexes is a key factor underlying the self-oscillations. Dynamic processes in the diffusion layer have been probed to give a better understanding of the self-oscillating process.</p><p>The self-oscillating behaviour is found to be an effect of pH variations in the diffusion layer. Mainly copper is deposited at lower pH values and potentials; at the same time, the pH increases. This is an effect of the dissociation of the Cu(II)-complex during electrochemical reduction. The absence of a buffer within a given pH region is crucial to the fast and sudden pH increase and thereby to the positive potential shift, where cuprous oxide is deposited. A precipitation reaction probably decreases the pH again, leading to a negative potential shift, and copper again begins to deposit. The concentration and strength of the buffer in the electrolyte affect the appearance of the oscillation pattern. The pH and temperature of the bulk electrolyte also influence the self-oscillations. The deposit consists of copper and cuprous oxide, where the composition of the phases deposited is a function of the working-electrode potential. Cuprous oxide is deposited at the higher potentials and mainly copper at the lower potentials.</p><p>Finally, two-dimensional arrays of Cu/Cu₂O microcylinders have been deposited using the Cu(II)-lactate system through the application of a template method.</p>

<p>Many materials exhibit interesting and novel properties when prepared as thin films. Thin film metal oxides have had an impact on the technological progress of the microelectronics mainly due to their electrical and optical properties. Since the future goes towards the nanometre scale there is an increasing demand for thin film deposition processes that can produce high quality metal oxide films in this scale with high accuracy.</p><p>This thesis describes atomic layer deposition of Ta₂O₅, HfO₂ and SnO₂ thin films and chemical vapour deposition of SnO₂ thin films. The films have been deposited by employing metal iodides and oxygen as precursors. All these processes have been characterised with regards to important processing parameters. The films themselves have been characterised by standard thin film analysing techniques such as x-ray diffraction, scanning electron microscopy, atomic force microscopy and transmission electron microscopy. The chemical and physical properties have been coupled to critical deposition parameters. Furthermore, additional data in the form of electrical and gas sensing properties important to future applications in the field of microelectronics have been examined.</p><p>The results from the investigated processes have shown the power of the metal iodide based atomic layer deposition (ALD) and chemical vapour deposition (CVD) processes in producing high quality metal oxide thin films. Generally no precursor contaminations have been observed. In contrast to metal chloride based processes the metal iodide processes produces films with a higher degree of crystalline quality when it comes to phase purity, roughness and epitaxy. The use of oxygen as oxidising precursor allowed depositions at higher temperatures than normally employed in water based ALD processes and hence a higher growth rate for epitaxial growth was possible.</p>