The high performance organic light-emitting diodes (OLEDs) have been studied. First, we have fabricated a WOLED with AlF3 and m-MTDATA as a hybrid buffer layer. Results indicate that the turn-on voltage can be reduced to 3.1V, and the luminous efficiency can be improved to 14.7 cd/A when a hybrid buffer layer was used. Since the turn-on voltage decreases and the efficiency increases, the power consumption as well as lifespan are then improved. Moreover, the luminous efficiency of the hybrid buffer layer devices also immunes to drive voltage variations. Second, we studied the properties of transportation in OLEDs. The study presented the device of a WOLED with a combination of a graded hole transport layer (GH) structure and a gradually doped emissive layer (GE) structure as a double graded (DG) structure. The DG structure: ITO/MTDATA(15 nm/NPB(15 nm)/NPB:25% BAlq (15 nm)/NPB : 50% BAlq (15 nm)/BAlq:0.5% Rubrene (10 nm)/ BAlq : 1% Rubrene (10nm) /BAlq:1.5%Rubrene (10 nm) / Alq3 (20 nm)/ LiF (0.5 nm)/Al (200 nm) is beneficial for improving both electrical and optical performances. The luminous efficiency of the DG device is 11.8cd/A, which is larger than that of 7.9cd/A with the HJ device. This improvement is attributed to the discrete interface between hole transport layer and emissive layer can be eliminated, surplus holes can be suppressed, electron-hole pairs can obtain optimal transportation and recombination in the emissive layer, and quenching effects can be significantly suppressed. Moreover, the spectra were almost not changed with an increasing drive current. As the efficiency was improved, it is expected that the power consumption can be reduced as well. Third, high efficiency and brightness p-i-n OLEDs with a CsI-doped Alq3 layer as a n-ETL has been studied. The p-i-n WOLED with a 15 % CsI-doped Alq3 layer exhibits a luminous efficiency of 5.75 cd/A at a driving current of 20mA/cm2 as well as a maximum power efficiency of 4.67lm/W. This improved performance is attributed to the increased electron carriers of the n-ETL and the balance of electrons and holes in the recombination zone. The X-ray photoelectron spectroscopy (XPS) have shown that doping of CsI caused chemical reaction, attributing to the increase of carriers. Finally, we focus on the improvement of contrast ration (CR) of OLEDs. We successfully fabricated a conductive organic-metal light-absorbing layer with a high CR and low reflectance for use as a black cathode in an OLED. The black cathode that was fabricated using vacuum deposition has the advantages of low cost and simple fabrication. Moreover, the J-V characteristic of the black cathode device is almost identical to that of a conventional device. Additionally, the reflectance can be reduced from 66.2% to 11.3% and a small reflectance variation around 3.3% over the visible spectrum is appealed. At an ambient illumination of 250 lx, the CR can be increased from 4.2 to 10.8 at a brightness of 250 cd/m2.

In this dissertation, we study the optical property of 2D graded photonic super-crystals (GPSCs) for photon management. We focused primarily on manipulation and control of light by using the newly discovered GPSCs which present great opportunity for electromagnetic wave control in photonic devices. The GPSC has been used to explore the superior capability of improving the light extraction efficiency of OLEDs. The enhancement of extraction efficiency has been explained in term of destructive interference of surface plasmon resonance and out-coupling of surface plasmon through phase matching provided by GPSC and verified by e-field intensity distributions. A large light extraction efficiency up to 75% into glass substrate has been predicted through simulation. We also study the light trapping enhancement in GPSCs. Broadband, wide incident angle, and polarization independent light trapping enhancement is achieved in silicon solar cells patterned with the GPSCs. In addition, novel 2D GPSCs were fabricated using holographic lithography through the interference lithography by two sets of multiple beams arranged in a cone geometry using a spatial light modulator (SLM). Finally, we also report a fabrication of GPSCs with a super-cell size of 12a×12a by using e-beam lithography. Diffraction pattern from GPSCs reveals unique diffraction properties. In an application aspect, light emitting diode arrays can be replaced by a single light emitting diode shinning onto the diffraction pattern for a uniform fluorescence.

The efficiency of organic light-emitting diodes (OLEDs) typically decreases with increasing current density. This so-called roll-off impedes the market entry of OLEDs in high-brightness applications such as general lighting. One of the most important processes causing roll-off is exciton annihilation, which evolves upon high exciton densities. This mechanism is especially pronounced in phosphorescent molecules due to their long triplet lifetime. In order to reduce the roll-off in phosphorescent OLEDs, this thesis focusses on decreasing the local exciton density by modifying the exciton lifetime, the spatial exciton distribution, and the tendency of emitters to form aggregates. The obtained results lead to a deeper understanding of efficiency roll-off and help sustaining the OLED efficiency at high brightness. The emitter lifetime can be influenced by the optical environment around the emitting dipoles through the Purcell effect. In order to study this effect, the distance between emitter and metal cathode is varied for two different OLED stacks. A strong influence of emitter position and orientation on roll-off is observed and explained by modelling the data with triplet-triplet annihilation theory. Furthermore, design principles for optimal high-brightness performance are established by simulating the roll-off as a function of emitter-cathode distance, emissive dipole orientation, and radiative efficiency. Next, a method is developed that allows extracting the spatial exciton distribution. Therefore, a thin sensing layer that locally quenches excitons is introduced into the emission layer at varying positions. The resulting quenching profile is then fitted using a comprehensive theory based on the diffusion equation, which renders the exciton distribution and diffusion length with nanometer resolution. This method is applied to an emission layer comprising an ambipolar host material. Contrary to expectations which suggest that ambipolar materials exhibit broad exciton formation, a narrow emission zone close to the electron transport layer is found. Additional explorations of structures that might broaden the emission zone point to a narrow emission zone in double emission layers and broader exciton formation in mixed emission layers. Previous investigations revealed a strong correlation between emitter aggregation and molecular dipole moment of the emitter. Within this thesis, the range of studied emitters is significantly extended. It is shown that homoleptic emitters show a stronger tendency to form aggregates than heteroleptic compounds. This is probably not only related to their higher dipole-dipole potential, but also to the molecular structure. Systematic analysis of the deposition parameters shows that aggregate formation depends on the underlying material and increases with increasing substrate temperature and decreasing evaporation rate. The two green emitters Ir(ppy)3 and Ir(ppy)2(acac) are additionally studied by means of X-ray diffraction. Both emitters form crystallite grains and exhibit a preferred orientation. Doping the emitters into an amorphous host, both orientation and crystallite formation retain at the investigated doping concentrations above 20 wt%. This result is a first step toward further understanding of the mechanism of transition dipole orientation.:List of Publications 1 Introduction 2 Principles of Organic Semiconductors 2.1 Molecular Orbitals 2.2 Optical Properties 2.3 Intermolecular Energy Transfer 2.4 Charge Transport 2.5 Organic Light-Emitting Diodes 2.5.1 Structure and Working Principle 2.5.2 Characterization 3 Theory of Efficiency Roll-Off 3.1 Current Status 3.2 Processes Leading to Roll-Off 3.2.1 Triplet-Triplet Annihilation 3.2.2 Triplet-Polaron Interaction 3.2.3 Further Processes Influencing Roll-Off 3.3 Interplay of the Various Processes 3.4 Scope of this Work 4 Experimental Methods 4.1 Sample Preparation 4.2 Measurement 4.2.1 Thin-Film Characterization 4.2.2 OLED Characterization 4.3 Materials 4.3.1 Electrodes, Transport Materials, and Blockers 4.3.2 Materials of the Emission Layer 5 Influence of the Optical Environment 5.1 Introduction 5.2 Influence of Emitter-Cathode Distance 5.3 Emitter Lifetime and Orientation 5.4 Correlation of Roll-Off and Orientation 5.5 Simulation of Roll-Off 5.5.1 Influence of the Electroluminescence Spectrum 5.5.2 Influence of Orientation and Radiative Efficiency 5.6 Conclusion 6 Influence of the Emission Profile 6.1 Preliminary Considerations 6.1.1 Exciton Generation and Diffusion 6.1.2 Width of the Emission Zone 6.1.3 Dependence on the Structure of the Emission Layer 6.2 Measurement of the Emission Profile 6.2.1 Method 6.2.2 Mathematical Description 6.2.3 Experimental Realization and Evaluation 6.3 Ambipolar Matrix Materials 6.3.1 Device Performance 6.3.2 Influence of the Sensing Layer 6.3.3 Emission Profile 6.4 Double- and Mixed Emission Layers 6.4.1 Emission Profile 6.4.2 Influence of the Matrix Ratio 6.5 Summary and Outlook 7 Influence of Molecular Aggregation 7.1 Introduction 7.2 Aggregation of Homoleptic and Heteroleptic Emitters 7.2.1 Photoluminescence Measurements 7.2.2 Time-Resolved Spectroscopy 7.2.3 X-Ray Diffraction 7.2.4 Conclusions on Emitter Orientation 7.2.5 Comparison of the Different Methods—Emitter Aggregation 7.3 Influence of the Matrix Material 7.3.1 Photoluminescence Measurements 7.3.2 Time-Resolved Spectroscopy 7.4 Influence of Processing Parameters 7.4.1 Substrate Heating 7.4.2 Underlying Layer 7.4.3 Evaporation Rate 7.5 Summary and Implications of Aggregation on Efficiency Roll-Off 8 Summary and Outlook 8.1 Summary of Roll-Off Investigations 8.2 Improving the High-Brightness Performance Further 8.3 Concluding Words on Emitter Orientation A Appendix to Theory of Efficiency Roll-Off B Appendix to Emission and Sensing Profiles B.1 Emission Profiles B.2 Emission Profiles Including a Sensing Layer B.3 Sensing Profiles C Appendix to Double- and Mixed Emission Layers C.1 Sample Uniformity C.2 Influence of the Sensor on Current Density C.3 Further D-EML and M-EML structures D Appendix to Molecular Aggregation List of Chemical Compounds List of Abbreviations List of Important Symbols Bibliography Acknowledgement / Die Effizienz organischer Leuchtdioden (OLEDs) nimmt üblicherweise mit ansteigender Stromdichte ab. Dieser so genannte Roll-Off erschwert den Markteintritt von OLEDs in Bereichen, die hohe Helligkeiten erfordern, wie beispielsweise in der Beleuchtung. Einer der wichtigsten Prozesse, die zu Roll-Off führen, ist die Annihilation von Exzitonen. Diese nimmt mit steigender Exzitonendichte zu und ist vor allem in phosphoreszenten OLEDs aufgrund der dort vorhandenen langen Triplettlebensdauer ein großer Verlustfaktor. Im Rahmen dieser Dissertation werden Methoden vorgestellt, die mittels Reduzierung der Exzitonendichte den Roll-Off in phosphoreszenten OLEDs verringern können. Dazu gehören die Veränderung der Exzitonenlebensdauer, die Untersuchung der räumlichen Verteilung der Exzitonen und die Erforschung der Bildung von Emitteraggregaten. Die gewonnenen Ergebnisse führen zu einem besseren Verständnis des Effizienz Roll-Offs und helfen, die Effizienz von OLEDs bei hohen Helligkeiten zu verbessern. Die Emitterlebensdauer kann über den Purcell-Effekt durch Veränderung des die emittierenden Dipole umgebenden elektromagnetischen Felds beeinflusst werden. Dieser Effekt wird genutzt, indem der Abstand zwischen Emitter und Metallelektrode für zwei verschiedene OLED-Aufbauten variiert wird. Der Roll-Off ist stark abhängig von der Position und Orientierung des Emitters und kann durch Modellierung der Daten auf Basis von Triplett-Triplett-Annihilation erklärt werden. Durch Simulation des Roll-Offs in Abhängigkeit des Emitter-Kathode-Abstands, der Orientierung und der strahlenden Effizienz der emittierenden Dipole werden Prinzipien zur optimalen Leistung von OLEDs bei hohen Helligkeiten entwickelt. Als nächstes wird eine Methode eingeführt mittels derer die räumliche Exzitonenverteilung extrahiert werden kann. Dafür wird eine dünne Sensorschicht in die Emissionsschicht eingebracht, die lokal Exzitonen auslöscht. Unter Variation der Position des Sensors wird ein Profil der Auslöschungsintensität bestimmt. Die gemessene Intensität wird mittels einer umfassenden Theorie auf Grundlage der Diffusionsgleichung angepasst, wodurch sich die räumliche Verteilung der Exzitonen und die Diffusionslänge mit einer Auflösung von 1nm ergibt. Die Methode wird auf eine Emissionsschicht angewandt, die das ambipolare Matrixmaterial CBP enthält. Entgegen der Erwartung, dass die Exzitonenbildung in ambipolaren Materialien weiter ausgedehnt ist, ist die gemessene Emissionszone sehr schmal und befindet sich an der Grenze zur Elektronentransportschicht. Um eine Verbreiterung des Emissionsprofils zu ermöglichen, werden weitere Strukturen untersucht. Dabei wird eine schmale Emissionszone in Doppelemissionsschichten beobachtet, wohingegen gemischte Emissionsschichten zu einer Verbreiterung der Exzitonenbildung führen können. Vorangegangene Untersuchungen deckten einen Zusammenhang zwischen der Aggregation von Emittermolekülen und dem Dipolmoment des Emitters auf. In dieser Arbeit werden weitere Emittermoleküle untersucht, wobei eine stärkere Aggregation von homoleptischen Emittern im Vergleich zu heteroleptischen festgestellt wird. Dies ist einerseits im höheren Dipol-Dipol-Potential der homoleptischen Verbindungen und andererseits in der Molekülstruktur begründet. Eine systematische Analyse der Herstellungsparameter zeigt, dass die Aggregatbildung von dem darunter liegenden Material abhängt und mit steigender Substrattemperatur und sinkender Verdampfungsrate zunimmt. Die zwei Grünemitter Ir(ppy)3 und Ir(ppy)2(acac) werden zusätzlich mittels Röntgenspektroskopie untersucht. Beide Emitter bilden kristalline Körner und weisen eine bevorzugte Orientierung auf. Sowohl die Kristallbildung als auch die Orientierung bleiben erhalten, wenn die Emitter mit mehr als 20 Gewichtsprozent in das Matrixmaterial CBP dotiert werden. Dieses Ergebnis ist ein erster Schritt zum besseren Verständnis der in vielen Iridium-Emittern beobachteten Orientierung des Übergangsdipolmoments.:List of Publications 1 Introduction 2 Principles of Organic Semiconductors 2.1 Molecular Orbitals 2.2 Optical Properties 2.3 Intermolecular Energy Transfer 2.4 Charge Transport 2.5 Organic Light-Emitting Diodes 2.5.1 Structure and Working Principle 2.5.2 Characterization 3 Theory of Efficiency Roll-Off 3.1 Current Status 3.2 Processes Leading to Roll-Off 3.2.1 Triplet-Triplet Annihilation 3.2.2 Triplet-Polaron Interaction 3.2.3 Further Processes Influencing Roll-Off 3.3 Interplay of the Various Processes 3.4 Scope of this Work 4 Experimental Methods 4.1 Sample Preparation 4.2 Measurement 4.2.1 Thin-Film Characterization 4.2.2 OLED Characterization 4.3 Materials 4.3.1 Electrodes, Transport Materials, and Blockers 4.3.2 Materials of the Emission Layer 5 Influence of the Optical Environment 5.1 Introduction 5.2 Influence of Emitter-Cathode Distance 5.3 Emitter Lifetime and Orientation 5.4 Correlation of Roll-Off and Orientation 5.5 Simulation of Roll-Off 5.5.1 Influence of the Electroluminescence Spectrum 5.5.2 Influence of Orientation and Radiative Efficiency 5.6 Conclusion 6 Influence of the Emission Profile 6.1 Preliminary Considerations 6.1.1 Exciton Generation and Diffusion 6.1.2 Width of the Emission Zone 6.1.3 Dependence on the Structure of the Emission Layer 6.2 Measurement of the Emission Profile 6.2.1 Method 6.2.2 Mathematical Description 6.2.3 Experimental Realization and Evaluation 6.3 Ambipolar Matrix Materials 6.3.1 Device Performance 6.3.2 Influence of the Sensing Layer 6.3.3 Emission Profile 6.4 Double- and Mixed Emission Layers 6.4.1 Emission Profile 6.4.2 Influence of the Matrix Ratio 6.5 Summary and Outlook 7 Influence of Molecular Aggregation 7.1 Introduction 7.2 Aggregation of Homoleptic and Heteroleptic Emitters 7.2.1 Photoluminescence Measurements 7.2.2 Time-Resolved Spectroscopy 7.2.3 X-Ray Diffraction 7.2.4 Conclusions on Emitter Orientation 7.2.5 Comparison of the Different Methods—Emitter Aggregation 7.3 Influence of the Matrix Material 7.3.1 Photoluminescence Measurements 7.3.2 Time-Resolved Spectroscopy 7.4 Influence of Processing Parameters 7.4.1 Substrate Heating 7.4.2 Underlying Layer 7.4.3 Evaporation Rate 7.5 Summary and Implications of Aggregation on Efficiency Roll-Off 8 Summary and Outlook 8.1 Summary of Roll-Off Investigations 8.2 Improving the High-Brightness Performance Further 8.3 Concluding Words on Emitter Orientation A Appendix to Theory of Efficiency Roll-Off B Appendix to Emission and Sensing Profiles B.1 Emission Profiles B.2 Emission Profiles Including a Sensing Layer B.3 Sensing Profiles C Appendix to Double- and Mixed Emission Layers C.1 Sample Uniformity C.2 Influence of the Sensor on Current Density C.3 Further D-EML and M-EML structures D Appendix to Molecular Aggregation List of Chemical Compounds List of Abbreviations List of Important Symbols Bibliography Acknowledgement

The thesis is focused on the study of electric and dielectric properties of thin film organic materials that can be used as an active layer of photovoltaic cells. Primarily were studied the properties of the layers on the glass substrates, which consist of a thin active layer of phthalocyanines. On the samples were first measured current-voltage characteristics (in the dark and during the exposure) and the basic parameters of the photovoltaic conversion were determined. Finally were measured frequency dependencies (impedance spectra, in the dark and during the exposure) and the parameters of a model of the structure with organic semiconductor were determined. The obtained results will be used to optimize the properties of photovoltaic cells.