No description available.

Diels-Alder chemistry was utilized to manipulate the surface energy of glass substrates in reversible manner. Glass slides and capillaries were functionalized with hydrophobic dieneophiles resulting in a non-wetting surface. A retro Diels-Alder reaction facilitated by the thermal treatment of the surface’s function to cleave the hydrophobic dieneophile and resulted in the fabrication of a hydrophilic surface. Contact angle (CA) measurements were used as preliminary measurements for monitoring the changes in surface energy exhibited during the initial hydrophobic state (CA - 70±3°), after attachment of the dieneophile creating a hydrophobic state (CA - 101±9°) followed by reestablishment of the hydrophilic state (CA - 70±6°) upon cleavage of the Diels-Alder adduct. The treatments developed on flat glass surfaces were transferred to glass capillaries, with effective treatment confirmed by fluid column measurements. Effective flow gating was developed in the capillaries via patterning of the surface with hydrophilic/hydrophobic regions. Finally, attempts to create self-pressurizing capillaries were unsuccessful due to pronounced contact angle hysteresis for the hydrophobic surface treatment. Indium-tin oxide (ITO) substrates were functionalized with successive surface intiated atom transfer radical polymerization (SI-ATRP) and electropolymerization. A novel hybrid styrenic/thiophene monomer (ProDOT-Sty) was synthesized and employed in the polymerization events. This unique monomer and combination of polymerization methods allowed for the templation of electropolymerized poly(3,4-alkyleneoxythiophene) brushes by first creating a poly(styrene) backbone via SI-ATRP. An ITO electrode functionalized with poly(ProDOT-Sty) brushes grafted from the ITO surface via SI-ATRP was analyzed via cyclic voltammetry which clearly indicated the electropolymerization event beginning at approximately +0.7 V vs Fc/Fc+. Photo patterning of the phosphonic acid ATRP initiator immobilized on the ITO surface was undertaken in order to create a surface that would limit growth of the polymer species to a patterned area for facile film brush thickness characterization via atomic force microscopy (AFM) at a later time. This was accomplished via lithography with ultraviolet radiation (UV) and was confirmed via scanning electron microscopy (SEM). A nanohetero structure composed of platinum tipped cadmium selenide seeded, cadium sulfide nanorods (CdSe@CdS-Pt NRs). CdSe quantum dots (QDs) with variable sizes were prepared by adjusting reaction temperatures and times. CdS nanorods were then grown utilizing the CdSe QDs as seeds. Various lengths of the CdSe@CdS NRs were produced that ranged from ~25 nm to ~135 nm. Investigation of the influence of the various synthetic conditions of the nanorod synthesis led to the conclusion that the ratio of CdSe seeds to Cd and S precursors could be manipulated in order to influence the length to which the nanorods grew. Pt tips were attached to an end of the CdSe@CdS nanorods as photocatalytic hydrogen production sites. TEM was utilized to characterize the different types of nanoparticles at each stage of assembly.

All-polymer solar cells (APSC) are a class of organic solar cells in which hole and electron transporting phases are made of conjugated polymers. Unlike polymer/fullerene solar cell, photoactive material of APSC can be designed to have hole and electron transporting polymers with complementary absorption range and proper frontier energy level offset. However, the highest reported PCE of APSC is 5 times less than that of polymer/fullerene solar cell. The low PCE of APSC is mainly due to: i) low charge separation efficiency; and ii) lack of optimal morphology to facilitate charge transfer and transport; and iii) lack of control over the exciton and charge transport in each phase. My research work is focused towards addressing these issues. The charge separation efficiency of APSC can be enhanced by designing novel electron transporting polymers with: i) broad absorption range; ii) high electron mobility; and iii) high dielectric constant. In addition to with the above parameters chemical and electronic structure of the repeating unit of conjugated polymer also plays a role in charge separation efficiency. So far only three classes of electron transporting polymers, CN substituted PPV, 2,1,3-benzothiadiazole derived polymers and rylene diimide derived polymers, are used in APSC. Thus to enhance the charge separation efficiency new classes of electron transporting polymers with the above characteristics need to be synthesized. I have developed a new straightforward synthetic strategy to rapidly generate new classes of electron transporting polymers with different chemical and electronic structure, broad absorption range, and high electron mobility from readily available electron deficient monomers. In APSCs due to low entropy of mixing, polymers tend to micro-phase segregate rather than forming the more useful nano-phase segregation. Optimizing the polymer blend morphology to obtain nano-phase segregation is specific to the system under study, time consuming, and not trivial. Thus to avoid micro-phase segregation, nanoparticles of hole and electron transporters are synthesized and blended. But the PCE of nanoparticle blends are far less than those of polymer blends. This is mainly due to the: i) lack of optimal assembly of nanoparticles to facilitate charge transfer and transport processes; and ii) lack of control over the exciton and charge transport properties within the nanoparticles. Polymer packing within the nanoparticle controls the optoelectronic and charge transport properties of the nanoparticle. In this work I have shown that the solvent used to synthesize nanoparticles plays a crucial role in determining the assembly of polymer chains inside the nanoparticle there by affecting its exciton and charge transport processes. To obtain the optimal morphology for better charge transfer and transport, we have also synthesized nanoparticles of different radius with surfactants of opposite charge. We propose that depending on the radius and/or Coulombic interactions these nanoparticles can be assembled into mineral structure-types that are useful for photovoltaic devices.

Polymeric materials are attractive candidates for the fabrication of low cost, large area photovoltaic devices. Controlling the band gap of the electroactive polymer is an essential factor in optimizing the resulting devices. In this dissertation, a methodology for the synthesis of well-defined semiconducting materials with tunable band gaps is described. First, the synthesis, characterization, and computational analysis of a variety of trimers consisting of two 3-hexylthiophene units flanking a central moiety consisting of thiophene, or one of the electron donating monomers isothianaphthene or thieno[3,4,b]thiophene will be described. From this analysis the influences of the electronic and steric structure of the materials will be investigated. Several of these trimers will then be used in the synthesis of well-defined, higher order, oligomers of thiophene and isothianaphthene in varying compositions. Polymerization of these oligomers yields polymers of known sequence allowing the band gap of the polymers to be systematically varied. Finally, preliminary investigations into the development of alternate oligomer core units will be described. The control over the band gap that this method affords will be useful in the optimization of polymeric semiconductor devices.

No description available.

No description available.

No description available.

<p>As a promising new technology, organic photovoltaics (OPVs) have been widely studied recently. To improve the device efficiency for commercial use of 10%, a number of attempts have been made in my research. The ultra-low frequency AC field was first employed, to align p/n polymers during fabrication. The resulting devices showed 15% increase in device efficiency, attributed to the optimized morphology and enlarged p/n interface. During the improvement process, dual nanostructures of the polymers were found, the highly oriented layer and the randomly distributed part, which provided a better understanding of the OPVs under the AC field alignment.</p> <p>The OPV stability was then studied by impedance measurements, to track multi-interface degradation without breaking the device. It was found the degradation of p/n junction was attributed to the deteriorated morphology and oxidized polymers, whereas the semiconductor/metal interface changed by producing metal oxides as degradation products.</p> <p>The dramatic contrast between the bilayer and bulk heterojunctions (BHJ) was at last investigated by capacitance measurements in vacuum. The existing models of the BHJs had difficulty explaining the higher overall capacitance, compared with that from the bilayer devices. The resulting puzzling charge density was clarified by separating the measured capacitance into two parallel components, one from the space charge of the proposed Schottky junction, and the other from the dark dipoles presumably formed spontaneously across the donor/acceptor interface.</p> / Doctor of Philosophy (PhD)

This thesis explores the evaporation kinetics of various polymer-solvent and binary solvent mixtures to explore possible connections between the solutions properties and their evaporation process. By looking at the evaporation of polymer-solutions and binary-solvent solutions, through the change in weight as the solvent evaporates and the evaporation rate of the evaporation process, potential connections could be found. The results indicate that the presence of polymers influence the solvent evaporation, with polystyrene (PS) generally accelerating and polymethyl methacrylate (PMMA) either decelerating or having minimal impact on evaporation rates. Binary solvent mixtures exhibited non-proportional increases in evaporation rates, suggesting complex intermolecular interactions, but no apparent patterns between their properties and deviation in the evaporation process. This would need further research to find possible connections to be able to predict the evaporation process. But these findings highlight the importance of understanding polymer-solvent compatibility and evaporation dynamics to enhance performance and to identify environmentally friendly solvents for organic photovoltaic (OPV) cell fabrication. / Detta examensarbete undersöker avdunstningskinetiken hos olika polymer-lösningsmedel och binära lösningsmedelsblandningar för att utforska möjliga samband mellan lösningarnas egenskaper och deras avdunstningsprocess. Genom att studera avdunstningen av polymer-lösningar och binära lösningsmedelslösningar, genom förändringen i vikt när lösningsmedlet avdunstar och avdunstningshastigheten, kan potentiella samband identifieras. Resultaten indikerar att närvaron av polymerer påverkar lösningsmedlets avdunstning, där polystyren (PS) generellt accelererar och polymetylmetakrylat (PMMA) antingen decelererar eller har minimal inverkan på avdunstningshastigheterna. Binära lösningsmedelsblandningar visade icke-proportionella ökningar i avdunstningstider, vilket tyder på komplexa intermolekylära interaktioner, men inga tydliga mönster mellan deras egenskaper och avvikelser i avdunstningsprocessen kunde identifieras. Ytterligare forskning behövs för att finna möjliga samband för att kunna förutsäga avdunstningsprocessen. Dessa fynd understryker vikten av att förstå polymer-lösningsmedelskompatibilitet och avdunstningsdynamik för att förbättra effektiviteten och kunna identifiera miljövänliga lösningsmedel för tillverkning av organiska solceller (OPV).

A novel fiber optic structure, termed stochastic ordered hole fibers, has been developed that contains an ordered array of six hollow tubes surrounding a hollow core, combined with a nanoporous glass creating a unique fully three dimensional pore/fiber configuration. The objective of this study is to increase the functionality of these stochastic ordered hole fibers, as well as porous clad fibers, by integrating electronic device components such as conductors, and semiconductors, and optically active materials on and in the optical fiber pore structures. Conductive copper pathways were created on/in the solid core fibers using an electroless deposition technique. A chemical vapor deposition system was built in order to attempt the deposition of silicon in on the porous clad fibers. Additionally, conductive poly(3,4-ethylenedioxythiophene)- poly(styrene sulfonate) (PEDOT:PSS) and photoactive polymer blend poly(3- hexylthiophene) and 1-(3-methoxycarbonyl)-propyl-1-phenyl-)6,6)C61 (P3HT: PCBM) were deposited on the fibers using dip coating techniques. Quantum dots of Cadmium Selenide (CdSe) with particle sizes of ranging from 2- 10 nm were deposited in the stochastic ordered hole fibers. SEM and EDS analysis confirm that copper, polymer materials, and quantum dots were deposited in the pore structure and on the surface of the fibers. Finally, resistance measurements indicate that the electrolessly deposited copper coatings have sufficient conductivity to be used as metallic contacts or resistive heating elements. / Master of Science