This thesis aims to improve the performance of latex-based pressure-sensitive adhesives (PSAs). PSA performance is usually evaluated by tack, peel strength and shear strength. Tack and peel strength characterize a PSA’s bonding strength to a substrate while shear strength reflects a PSA’s capability to resist shear deformation. In general, increasing shear strength leads to a decrease in tack and peel strength. While there are several commercial PSA synthesis methods, the two most important methods consist of either solvent-based or latex-based techniques. While latex-based PSAs are more environmentally compliant than solvent-based PSAs, they tend to have much lower shear strength, at similar tack and peel strength levels. Therefore, the goal in this thesis was to greatly improve the shear strength of latex-based PSAs at little to no sacrifice to tack and peel strength. In this study, controlling the polymer microstructure of latexes or their corresponding PSA films was used as the main method for improving the PSA performance. The research was sub-divided into four parts. First, the influence of chain transfer agent (CTA) and cross-linker on latex polymer microstructure was studied via seeded semi-batch emulsion polymerization of butyl acrylate (BA) and methyl methacrylate (MMA). Three techniques were used to produce the latexes: (1) adding CTA only, (2) adding cross-linker only, and (3) adding both CTA and cross-linker. It was found that using CTA and cross-linker simultaneously allows one to expand the range of latex microstructural possibilities. For example, latexes with similar gel contents but different Mc (molecular weight between cross-links) and Mw (molecular weight of sol polymers) could be produced if CTA and cross-linker concentration are both increased. However, for the corresponding PSAs with similar gel contents, the relationship between their polymer microstructure and performance was difficult to establish as almost all of the medium and high gel content PSAs showed very low tack and peel strength as well as extremely large shear strength readings. In the second part of this thesis, in order to improve the tack and peel strength of medium and high gel content PSAs, the monomer composition and emulsifier concentration were varied. It was found that changing the monomer mixture from BA/MMA to BA/acrylic acid (AA)/2-hydroxyethyl methacrylate (HEMA) while simultaneously decreasing emulsifier concentration dramatically improved the corresponding PSAs’ shear strength as well as tack and peel strength. The addition of polar groups to the PSA increased its cohesive strength due to the presence of strong hydrogen bonding; meanwhile, PSA films’ surface tension increased. In the third part, two series of BA/AA/HEMA latexes were generated by varying the amounts of CTA either in the absence or presence of cross-linker. The latexes produced in the absence of cross-linker exhibited significantly larger Mc and Mw compared to their counterparts with similar gel contents prepared with cross-linker. The PSAs with the larger Mc and Mw showed much larger shear strengths due to improved entanglements between the polymer chains. In the final part of the thesis, the performance of the BA/AA/HEMA PSAs was further improved by post-heating. Compared with original latex-based PSAs with similar gel contents, heat-treated PSAs showed not only significantly improved shear strengths, but also much larger tack and peel strengths. The different shear strengths were related to the PSAs’ gel structures, which were discrete in the original PSAs but continuous in the heat-treated PSAs. The improved tack and peel strengths were related to the PSA films’ surface smoothness. During the post-heating process, the PSA polymer flowed, resulting in much smoother surfaces than the original PSA films. In addition, the effect of post-heating was related to the polymer microstructure of the untreated PSAs. Decreasing the amount of very small or very big polymers or simultaneously increasing Mc and Mw could lead to post-treated PSAs with significantly better performance. Moreover, it was found that by optimizing the polymer microstructure of the original latex-based PSAs, it was possible to obtain a treated PSA with similar or even better performance than a solvent-based PSA with similar polymer microstructure. Our original objective was surpassed: in two cases, not only was shear strength greatly improved, but so were tack and peel strength due to the simultaneous modification of PSA bulk and surface properties.

This thesis aims to improve the performance of latex-based pressure-sensitive adhesives (PSAs). PSA performance is usually evaluated by tack, peel strength and shear strength. Tack and peel strength characterize a PSA’s bonding strength to a substrate while shear strength reflects a PSA’s capability to resist shear deformation. In general, increasing shear strength leads to a decrease in tack and peel strength. While there are several commercial PSA synthesis methods, the two most important methods consist of either solvent-based or latex-based techniques. While latex-based PSAs are more environmentally compliant than solvent-based PSAs, they tend to have much lower shear strength, at similar tack and peel strength levels. Therefore, the goal in this thesis was to greatly improve the shear strength of latex-based PSAs at little to no sacrifice to tack and peel strength. In this study, controlling the polymer microstructure of latexes or their corresponding PSA films was used as the main method for improving the PSA performance. The research was sub-divided into four parts. First, the influence of chain transfer agent (CTA) and cross-linker on latex polymer microstructure was studied via seeded semi-batch emulsion polymerization of butyl acrylate (BA) and methyl methacrylate (MMA). Three techniques were used to produce the latexes: (1) adding CTA only, (2) adding cross-linker only, and (3) adding both CTA and cross-linker. It was found that using CTA and cross-linker simultaneously allows one to expand the range of latex microstructural possibilities. For example, latexes with similar gel contents but different Mc (molecular weight between cross-links) and Mw (molecular weight of sol polymers) could be produced if CTA and cross-linker concentration are both increased. However, for the corresponding PSAs with similar gel contents, the relationship between their polymer microstructure and performance was difficult to establish as almost all of the medium and high gel content PSAs showed very low tack and peel strength as well as extremely large shear strength readings. In the second part of this thesis, in order to improve the tack and peel strength of medium and high gel content PSAs, the monomer composition and emulsifier concentration were varied. It was found that changing the monomer mixture from BA/MMA to BA/acrylic acid (AA)/2-hydroxyethyl methacrylate (HEMA) while simultaneously decreasing emulsifier concentration dramatically improved the corresponding PSAs’ shear strength as well as tack and peel strength. The addition of polar groups to the PSA increased its cohesive strength due to the presence of strong hydrogen bonding; meanwhile, PSA films’ surface tension increased. In the third part, two series of BA/AA/HEMA latexes were generated by varying the amounts of CTA either in the absence or presence of cross-linker. The latexes produced in the absence of cross-linker exhibited significantly larger Mc and Mw compared to their counterparts with similar gel contents prepared with cross-linker. The PSAs with the larger Mc and Mw showed much larger shear strengths due to improved entanglements between the polymer chains. In the final part of the thesis, the performance of the BA/AA/HEMA PSAs was further improved by post-heating. Compared with original latex-based PSAs with similar gel contents, heat-treated PSAs showed not only significantly improved shear strengths, but also much larger tack and peel strengths. The different shear strengths were related to the PSAs’ gel structures, which were discrete in the original PSAs but continuous in the heat-treated PSAs. The improved tack and peel strengths were related to the PSA films’ surface smoothness. During the post-heating process, the PSA polymer flowed, resulting in much smoother surfaces than the original PSA films. In addition, the effect of post-heating was related to the polymer microstructure of the untreated PSAs. Decreasing the amount of very small or very big polymers or simultaneously increasing Mc and Mw could lead to post-treated PSAs with significantly better performance. Moreover, it was found that by optimizing the polymer microstructure of the original latex-based PSAs, it was possible to obtain a treated PSA with similar or even better performance than a solvent-based PSA with similar polymer microstructure. Our original objective was surpassed: in two cases, not only was shear strength greatly improved, but so were tack and peel strength due to the simultaneous modification of PSA bulk and surface properties.

This thesis aims to improve the performance of latex-based pressure-sensitive adhesives (PSAs). PSA performance is usually evaluated by tack, peel strength and shear strength. Tack and peel strength characterize a PSA’s bonding strength to a substrate while shear strength reflects a PSA’s capability to resist shear deformation. In general, increasing shear strength leads to a decrease in tack and peel strength. While there are several commercial PSA synthesis methods, the two most important methods consist of either solvent-based or latex-based techniques. While latex-based PSAs are more environmentally compliant than solvent-based PSAs, they tend to have much lower shear strength, at similar tack and peel strength levels. Therefore, the goal in this thesis was to greatly improve the shear strength of latex-based PSAs at little to no sacrifice to tack and peel strength. In this study, controlling the polymer microstructure of latexes or their corresponding PSA films was used as the main method for improving the PSA performance. The research was sub-divided into four parts. First, the influence of chain transfer agent (CTA) and cross-linker on latex polymer microstructure was studied via seeded semi-batch emulsion polymerization of butyl acrylate (BA) and methyl methacrylate (MMA). Three techniques were used to produce the latexes: (1) adding CTA only, (2) adding cross-linker only, and (3) adding both CTA and cross-linker. It was found that using CTA and cross-linker simultaneously allows one to expand the range of latex microstructural possibilities. For example, latexes with similar gel contents but different Mc (molecular weight between cross-links) and Mw (molecular weight of sol polymers) could be produced if CTA and cross-linker concentration are both increased. However, for the corresponding PSAs with similar gel contents, the relationship between their polymer microstructure and performance was difficult to establish as almost all of the medium and high gel content PSAs showed very low tack and peel strength as well as extremely large shear strength readings. In the second part of this thesis, in order to improve the tack and peel strength of medium and high gel content PSAs, the monomer composition and emulsifier concentration were varied. It was found that changing the monomer mixture from BA/MMA to BA/acrylic acid (AA)/2-hydroxyethyl methacrylate (HEMA) while simultaneously decreasing emulsifier concentration dramatically improved the corresponding PSAs’ shear strength as well as tack and peel strength. The addition of polar groups to the PSA increased its cohesive strength due to the presence of strong hydrogen bonding; meanwhile, PSA films’ surface tension increased. In the third part, two series of BA/AA/HEMA latexes were generated by varying the amounts of CTA either in the absence or presence of cross-linker. The latexes produced in the absence of cross-linker exhibited significantly larger Mc and Mw compared to their counterparts with similar gel contents prepared with cross-linker. The PSAs with the larger Mc and Mw showed much larger shear strengths due to improved entanglements between the polymer chains. In the final part of the thesis, the performance of the BA/AA/HEMA PSAs was further improved by post-heating. Compared with original latex-based PSAs with similar gel contents, heat-treated PSAs showed not only significantly improved shear strengths, but also much larger tack and peel strengths. The different shear strengths were related to the PSAs’ gel structures, which were discrete in the original PSAs but continuous in the heat-treated PSAs. The improved tack and peel strengths were related to the PSA films’ surface smoothness. During the post-heating process, the PSA polymer flowed, resulting in much smoother surfaces than the original PSA films. In addition, the effect of post-heating was related to the polymer microstructure of the untreated PSAs. Decreasing the amount of very small or very big polymers or simultaneously increasing Mc and Mw could lead to post-treated PSAs with significantly better performance. Moreover, it was found that by optimizing the polymer microstructure of the original latex-based PSAs, it was possible to obtain a treated PSA with similar or even better performance than a solvent-based PSA with similar polymer microstructure. Our original objective was surpassed: in two cases, not only was shear strength greatly improved, but so were tack and peel strength due to the simultaneous modification of PSA bulk and surface properties.

Background: Public service advertising in China just has two decades years of history and media used for public service advertising mainly focus on print advertising. Compared to commercial advertising, public service advertising is not mature in China whatever in the forms, content variety or media. Chinese internet users have increased rapidly in recent years, so in this situation, the development of online PSAs is especially important. While many researches focus on print media, few are about PSAs on internet. The money of charity organization spent on PSAs is rare, because the donators want their donation spent on important place. So the quality of PSAs is important to attract people’s attention.Purpose: The purpose of this thesis is to investigate the factors influencing college students’ attitude toward online public service advertising for recruiting volunteers.Method: A quantitative method is taken in this thesis. The primary data are collected through questionnaire and the sample is college students in university in Shanghai for science and technology. The secondary data come from mainly E-library, E-journal and books. To analyze the data, hypothesis testing method is used and SPSS is used as statistical analysis tool.Conclusions: Entertainment, informativeness, irritation, credibility and advertising value these factors from Ducoffe’s model are applied to the research on attitude toward PSAs. The result shows that factors of entertainment, informativeness and advertising value have positive influence on college students’ attitude, while factors of irritation and credibility don’t have influence on college students’ attitude toward volunteer recruitment PSAs, thus they have a nearly neutral attitude. Entertainment and informativeness have significant correlation with advertising value separately, and this situation can also be applied to attitude toward PSAs. Advertising value has significant correlation with attitude toward PSAs. So the Ducoffe’s model is not totally appropriate for the research on attitude toward PSAs.

This thesis aims to improve the performance of latex-based pressure-sensitive adhesives (PSAs). PSA performance is usually evaluated by tack, peel strength and shear strength. Tack and peel strength characterize a PSA’s bonding strength to a substrate while shear strength reflects a PSA’s capability to resist shear deformation. In general, increasing shear strength leads to a decrease in tack and peel strength. While there are several commercial PSA synthesis methods, the two most important methods consist of either solvent-based or latex-based techniques. While latex-based PSAs are more environmentally compliant than solvent-based PSAs, they tend to have much lower shear strength, at similar tack and peel strength levels. Therefore, the goal in this thesis was to greatly improve the shear strength of latex-based PSAs at little to no sacrifice to tack and peel strength. In this study, controlling the polymer microstructure of latexes or their corresponding PSA films was used as the main method for improving the PSA performance. The research was sub-divided into four parts. First, the influence of chain transfer agent (CTA) and cross-linker on latex polymer microstructure was studied via seeded semi-batch emulsion polymerization of butyl acrylate (BA) and methyl methacrylate (MMA). Three techniques were used to produce the latexes: (1) adding CTA only, (2) adding cross-linker only, and (3) adding both CTA and cross-linker. It was found that using CTA and cross-linker simultaneously allows one to expand the range of latex microstructural possibilities. For example, latexes with similar gel contents but different Mc (molecular weight between cross-links) and Mw (molecular weight of sol polymers) could be produced if CTA and cross-linker concentration are both increased. However, for the corresponding PSAs with similar gel contents, the relationship between their polymer microstructure and performance was difficult to establish as almost all of the medium and high gel content PSAs showed very low tack and peel strength as well as extremely large shear strength readings. In the second part of this thesis, in order to improve the tack and peel strength of medium and high gel content PSAs, the monomer composition and emulsifier concentration were varied. It was found that changing the monomer mixture from BA/MMA to BA/acrylic acid (AA)/2-hydroxyethyl methacrylate (HEMA) while simultaneously decreasing emulsifier concentration dramatically improved the corresponding PSAs’ shear strength as well as tack and peel strength. The addition of polar groups to the PSA increased its cohesive strength due to the presence of strong hydrogen bonding; meanwhile, PSA films’ surface tension increased. In the third part, two series of BA/AA/HEMA latexes were generated by varying the amounts of CTA either in the absence or presence of cross-linker. The latexes produced in the absence of cross-linker exhibited significantly larger Mc and Mw compared to their counterparts with similar gel contents prepared with cross-linker. The PSAs with the larger Mc and Mw showed much larger shear strengths due to improved entanglements between the polymer chains. In the final part of the thesis, the performance of the BA/AA/HEMA PSAs was further improved by post-heating. Compared with original latex-based PSAs with similar gel contents, heat-treated PSAs showed not only significantly improved shear strengths, but also much larger tack and peel strengths. The different shear strengths were related to the PSAs’ gel structures, which were discrete in the original PSAs but continuous in the heat-treated PSAs. The improved tack and peel strengths were related to the PSA films’ surface smoothness. During the post-heating process, the PSA polymer flowed, resulting in much smoother surfaces than the original PSA films. In addition, the effect of post-heating was related to the polymer microstructure of the untreated PSAs. Decreasing the amount of very small or very big polymers or simultaneously increasing Mc and Mw could lead to post-treated PSAs with significantly better performance. Moreover, it was found that by optimizing the polymer microstructure of the original latex-based PSAs, it was possible to obtain a treated PSA with similar or even better performance than a solvent-based PSA with similar polymer microstructure. Our original objective was surpassed: in two cases, not only was shear strength greatly improved, but so were tack and peel strength due to the simultaneous modification of PSA bulk and surface properties.

No description available.

Post surgical adhesions (PSAs) are an inevitable outcome of surgery and their presence leads to pathogeneses and significant economic impact. The studies within this thesis utilised standard and reproducible abrasion models, in rabbits, pigs and rats, to investigate the formation and maturation of PSAs with strict quantitative analyses. These studies have shown that the development of PSAs is a series of complex, multi-factorial processes. PSA development can be classified into two stages: (i) PSA modelling occurring up to/including 16 hours post injury characterised by the inflammatory response and fibrin deposition and maturation; and (ii) PSA remodelling occurring from 16 hours onwards and characterised by tissue repair, collagen deposition and maturation and chemical mediation by TGF-P. Treatment with VivostatTM System Derived (novel) Fibrin Sealant significantly reduced the formation of PSAs with mean PSA reduction of 80% for the rabbit uterine horn abrasion model, from 3 separate studies; 83% for the pig stomach/colon/caecum abrasion model, from 2 separate studies; 80% for the rat caecum abrasion model. This is significantly better than other fibrin sealants investigated in this thesis. PSA prevention with novel fibrin sealant demonstrated a similar pattern to PSA development, with two stages of development evident: (i) tissue generation modelling occurring up to/including 16 hours post injury characterised by the inflammatory response and fibrin deposition and maturation; and (ii) tissue generation remodelling occurring from 16 hours onwards and characterised by tissue repair, collagen deposition and maturation and chemical mediation by TGF-P. However the extent and subsequent time taken for these changes to occur was significantly reduced. The prevention of PSAs and alterations of wound healing by novel fibrin sealant is most probably due to the sealant acting as a haemostat, as well as a physical barrier. Thus preventing fibrinous and subsequent fibrous PSA formation.

Pressure sensitive adhesives (PSAs) are polymeric materials with versatile applications in industrial and consumer products such as protective films, product labels, masking tape, and sticky notes, to name a few applications. World demand for emulsion–based products is on the rise due to worldwide legislation on solvent emissions. In order to completely replace emulsion-based PSAs with their solvent-based counterpart, the property modification of emulsion-based PSAs is required. The use of nanomaterials to modify polymer properties is well established. The aim of this thesis was to use cellulose nanocrystals (CNCs) as property modifiers for emulsion-based PSAs. CNCs are recognized as a highly efficient reinforcement nanofiller. Owing to their environmentally friendly characteristics, low density, high aspect ratio, non-toxicity, and abundant availability, the application of CNCs in composite materials is gaining increasing attention. In this thesis, the inclusion of CNCs in emulsion-based PSAs was carried out through in situ emulsion polymerization and blending technique. To the best of our knowledge, there is limited information about the synthesis of CNC/PSAs nanocomposites via in situ emulsion polymerization and the evaluation of their mechanical performance. The addition of CNCs to the polymerization formulation caused latex instability due to the negatively charged surfaces of the CNCs. After numerous attempts to overcome the stability issues, a stable polymerization formulation and protocol were developed. CNC/PSAs were synthesized via in situ seeded-semi batch emulsion polymerization, which is a common commercial production pathway for PSAs. The mechanical performance of the resulting PSA nanocomposite films, namely, shear strength, tack, and peel strength, was evaluated at several CNC loadings. All three PSA adhesive properties were simultaneously enhanced with increasing CNC loading. The inclusion of CNCs into the films increased their hydrophilicity. Consequently, the PSA films’ improved wettability on a stainless steel substrate imparted greater tack and peel strength. The blending of the CNCs with a base latex also led to improved adhesive properties. However, the property modification through blending was not as effective as that for the CNC/PSA films synthesized via in situ emulsion polymerization. Thus, CNCs are safe nanomaterials that have been shown to provide remarkable property enhancement of emulsion-based PSA films at low loadings (1wt%).

La sénescence cellulaire, ou l’arrêt irréversible de la prolifération, influence des processus physiologiques et pathologiques, comme le cancer. Parmi les caractéristiques de la sénescence, se retrouve le PSAS ou phénotype sécrétoire associé à la sénescence. Le PSAS est composé d’une variété de cytokines, facteurs de croissance et protéases. Ses actions pro- et anti-tumorale sont connues, mais l’on ignore laquelle prédomine. Mes travaux s’attardent aux effets du PSAS sur l’induction de la sénescence dans les cellules environnantes et à sa régulation. Nous avons démontré que le PSAS ne synergise pas avec la dysfonction télomérique chronique ou aigue, afin de causer un arrêt de croissance. Également, l’étude du mécanisme responsable de l’induction de la sénescence par stress à la chromatine, suggère que la kinase c-Abl n’est pas requise pour cette voie, contrairement à des publications antérieures. Mes travaux éclairent les mécanismes d’action et la régulation du PSAS dans la sénescence induite par dysfonction télomérique et par stress à la chromatine. / Cellular senescence, or irreversible proliferation arrest, is known for its influence on physiological and pathological processes, such as cancer. Among the features found in the senescent phenotype is the inflammatory secretome, also known as the senescence associated secretory phenotype (SASP). The SASP consists of a variety of factors such as cytokines, growth factors and proteases. It is widely recognized that SASP can have either a pro- or anti-tumor effect, but it is not clear which one predominates. My work focused on the SASP effects on the induction of senescence in surrounding cells and its regulation mechanisms. We demonstrated that the SASP does not synergize with chronic or induced telomere dysfunction to cause cellular proliferation arrest. Also, study of chromatin stress-induced senescence mechanism suggests that kinase c-Abl is not required for this pathway, contrary to what had been previously published. My work helps understand the regulatory and working mechanisms of the SASP in chromatin stress-induced and telomere dysfunction-induced senescence models.

La sénescence cellulaire est un arrêt stable du cycle cellulaire qui empêche la prolifération des cellules endommagées par des stress génotoxiques, tels que l'irradiation. En général, les lésions de l'ADN initient rapidement une réponse aux dommages et un blocage transitoire du cycle cellulaire nécessaire à la réparation de l'ADN. Cependant, les phénotypes associés à la sénescence, tels que l'arrêt de la prolifération stable et le sécrétome pro-inflammatoire, se manifestent plusieurs jours après le stress. Nous avons récemment démontré que l'établissement de la sénescence induite par l'irradiation est un processus en plusieurs étapes qui nécessite un événement prolifératif en présence de foyers de dommages de l'ADN persistants pour former de l'instabilité génomique. L'instabilité génomique secondaire, et non les dommages primaires de l'ADN, est responsable de nombreux phénotypes de sénescence. Le but de notre projet était d'évaluer l'impact de p16INK4a, un inhibiteur de kinase dépendant des cyclines, sur la reprise de la prolifération observée dans notre modèle initial en caractérisant la reprise de la prolifération, les phénotypes de sénescence lorsque p16INK4a est fortement exprimé, et de comprendre sa dynamique d'activation. Notre hypothèse était que l'expression de p16INK4a réduirait la reprise de la prolifération après l'irradiation, ce qui diminuerait la formation d'instabilité génomique et altérerait l'expression de certains phénotypes de sénescence. Nous avons induit la sénescence par irradiation dans des fibroblastes humains normaux qui présentent des niveaux endogènes différents d'expression de p16INK4a. Nous avons également utilisé une lignée qui surexprime et une autre qui déplète p16INK4a pour évaluer les conséquences de son expression sur la reprise de la prolifération et son impact sur les phénotypes de sénescence. Nos résultats suggèrent que p16INK4a réduit la reprise de la prolifération, diminuant l'instabilité génomique et réduisant à terme l'expression des facteurs du phénotype sécrétoire. De plus, de manière surprenante, nous avons observé que l'expression de p16INK4a n'a pas besoin d'être présente uniquement au moment de la reprise de la prolifération pour l'empêcher. Elle peut durer 24 heures au moment de l'irradiation, soit avant la reprise de la prolifération, pour la prévenir. Les données présentées dans ce mémoire aident à mieux comprendre le mécanisme de sénescence médié par l'irradiation et l'impact de l'expression de p16INK4a sur les différents phénotypes de sénescence. / Cellular senescence is a stable cell cycle arrest that prevents proliferation of cells damaged by genotoxic stresses, such as irradiation. In general, DNA damage initiates a DNA damage response and a transient cell cycle arrest required for DNA repair. However, senescence-associated phenotypes, such as stable senescence-associated proliferation arrest and pro-inflammatory secretome are established several days later. We have recently shown that the establishment of irradiation-induced senescence is a multi-step process that requires a proliferation event in the presence of persistent DNA damage foci to form genomic instability. Secondary genomic instability, but not primary DNA damage, leads to the establishment of senescence phenotypes. The aim of our project was to evaluate the impact of p16INK4a, a cyclin-dependent kinase inhibitor, on the bypass of the transient cell cycle arrest we observed in our initial model by characterizing the bypass and senescence phenotypes when p16INK4a was highly expressed and to understand its activation dynamics. Our hypothesis was that p16INK4a expression would reduce the percentage of bypass after irradiation which would decrease genomic instability formation and ultimately alter the expression of some senescence phenotypes. We induced senescence by irradiation in normal human fibroblasts with different endogenous levels of p16INK4a expression. We also used a cell line that overexpresses and another that depletes p16INK4a to evaluate the consequences of its expression on the bypass and its impact on senescence phenotypes. Our results suggest that p16INK4a decreases the bypass, thus reducing the genomic instability and, therefore, reduces expression of secretory phenotype factors. Moreover, interestingly, we observed that p16INK4a expression does not need to be present only at the time of reproliferation to prevent it, i.e. it can last 24 hours at the time of irradiation. These results contribute to improve our knowledge about the mechanism of establishment of irradiation-mediated senescence and the impact of p16INK4a expression on different senescence phenotypes.