Polymers are with low carrier mobility. If polymer solar cells are to exhibit high power conversion efficiencies, their carrier mobilities must be improved. Metallic NPs are promising materials for use in polymer solar cells because of their high conductivities. In this work, we studied the carrier transport characteristic of metallic nanoparticle blending into polymers. We blended Pt nanoparticles (Pt NPs) and Pd nanoparticles (Pd NPs) into polymers to improve carrier mobility, and enhance the power conversion efficiency of the polymer solar cell. P3HT was used as a donor material because of its high stability and with high absorption in visible light. PCBM was used as a acceptor material because of its high stability and with high electron transportation. We blended modified Pt NPs and Pd NPs into the P3HT:PCBM active layer, with the device configurations of ITO/PEDOT:PSS/P3HT:PCBM: Pt NPs/Al and ITO/PEDOT:PSS/P3HT:PCBM:Pd NPs/Al, respectively polymer solar cells measured was under AM 1.5G 100mW/cm2 illumination. When we blended Pt NPs into the active layer, the open-circuit remained 0.64V, the short-circuit current increased from 6.67mA/cm2 to 9mA/cm2, the power conversion efficiency increased from 1.96% to 3.08%. When we blended Pd NPs into the active layer, the open-circuit remained 0.62V, the short-circuit current increased from 6.33mA/cm2 to 7.33mA/cm2, the power conversion efficiency increased from 1.7% to 2.48%. The enhanced efficiency originated from the increased carrier mobility of the active layer when the Pt NPs or Pd NPs were present.

Detoxification of chlorinated organic compound is an important and urgent issue in water remediation nowadays. Trichloroethylene (TCE), as a model compound in this study, has been proved to be degraded effectively by bimetallic nanoparticles (NPs) in solution phase. In this study, Fe/Pd bimetallic NPs were synthesized in poly (acrylic acid) (PAA) functionalized polyvinylidene fluoride (PVDF) microfiltration membranes. TCE dechlorination with these bimetallic NPs was conducted under different pH values and different metal loadings to study the role of corrosion on reaction rates. One-dimensional mathematical model with pseudo first-order reaction kinetic was introduced to discuss the TCE dechlorination profile in membrane system. Reduction reaction in pores is affected by several parameters including NP loading and size, TCE diffusivity, void volume fraction and surface-area-based reaction rates. This model result indicated that modification is needed to correct the reaction rate obtained from bulk solution in order to represent the actual efficiency of NPs on reduction reaction. In addition, TCE dechlorination mainly occurred near NPs’ surface. Second part of model indicated that reduction mechanism with TCE adsorption-desorption behavior could be used to discuss dechlorination with a high TCE concentration.

Colloidal nanoparticles are widely used for industrial and scientific purposes in many fields, including catalysis, biosensing, drug delivery, and electrochemistry. It has been reported that most of the functional properties and performance of the nanoparticles are highly dependent on the particle size and morphology. Therefore, controlled synthesis of nanomaterials with desired size and structure is greatly beneficial to the application. This dissertation presents a systematic study on the effect of ligands on the colloidal Pd nanoparticle synthesis mechanism, kinetics, and final particle size. Specifically, the research is focused on investigating how the ligand bindings to different metal species, i.e., metal precursor and nanoparticle surface, affect the nucleation and growth pathways and rates and connecting the binding thermodynamics to the kinetics quantitatively. The first part of the work (Chapters 4 and 5) is establishing isothermal titration calorimetry (ITC) methodology for obtaining the thermodynamic values (Gibbs free energy, equilibrium constant, enthalpy and entropy) of the ligand-metal precursor binding reactions, and the simultaneous metal precursor trimer dissociation. In brief, the binding products and reactions were characterized by nuclear magnetic resonance (NMR), and an ITC model was developed to fit the unique ITC heat curve and extract the thermodynamic properties of the reactions above. Furthermore, in Chapter 6, the thermodynamic properties, especially the entropy trend changing with the ligand chain length was investigated on different metal precursors based on the established ITC methodology, showing that the entropic penalty plays a significant role in the binding equilibrium. The second part of the dissertation (Chapter 7 and 8) presents the kinetic and mechanistic study on size-tuning of the colloidal Pd nanoparticles only by changing different coordinating solvents as ligands together with the trioctylphosphine ligand. In-situ small angle X-ray scattering was applied to characterize the time evolutions of size, size distribution, and particle concentration using synthesis reactor connected to a capillary flow cell. From the real-time kinetic measurements, the nucleation and growth rates were calculated and correlated with the thermodynamics, i.e., Gibbs free energies of solvent-ligand-metal precursor reactivity and ligand-nanoparticle surface binding which were modified by the coordination of different solvents. Higher reactivity leads to faster nucleation and high nanoparticle concentration, and stronger solvent/ligand-particle coordination energy results in higher ligand capping density and slower growth. The interplay of both effects reduces the final particle size. Furthermore, because of the significance of the ligand-metal interactions, the synthesis temperature and ligand to metal precursor ratio were systematically to modify the relative binding between the ligand and precursor, and the ligand and nanoparticle, and determine the effect on the nucleation and growth rates. The results show that the relative rates of nucleation and growth is critical to the final size. A methodology for using the in-situ measurements to predict the final size by developing a kinetic model based is discussed. / Doctor of Philosophy / Metal nanoparticles dispersed in solution phase, i.e., colloidal nanoparticles, are of great scientific interests due to their unique properties different from bulk metal materials. The size, shape and other morphology features can largely affect the nanomaterial properties and functional performances. Therefore, a successful synthesis of nanoparticles with desired structures is highly beneficial to the development of their application. Ligands, which are long-chain molecules that can cap on the surface of the nanoparticles, have been known as stabilizers of the nanoparticles in the solution phase. Whereas in recent studies, it has been found that changing the ligand type and concentration in the synthesis can result in different sizes and shapes of nanomaterials, which indicates that the ligands are playing critical roles in the synthesis mechanisms to control the kinetics. To have a better understanding on the control effects of the ligands, systematic studies were conducted on the ligand interactions (bindings) between the ligand-metal compound (as the metal source and initial agent in the nanomaterial synthesis) and ligand-nanoparticle surface, of which both can be quantified by thermodynamics. Using isothermal titration calorimetry, the ligand-metal precursor binding strength was measured and found to be dependent on ligand chain length and the metal precursors, which further affects the reactivity of the metal precursor based on the results of density functional theory calculations. On the other hand, the ligand-nanoparticle surface binding strength was found to affect the capping density of the ligands on the nanoparticle surface. In order to connect the thermodynamics to the kinetics, namely the nucleation (formation of new particles) and growth (particle size increase) rates, small angle X-ray scattering (SAXS) characterization was performed in real time during the synthesis on the nanoparticles. This technique allows the capture of the size, size distribution and concentration of nanoparticles changing with time, and the nucleation and growth rates were further calculated from the SAXS data. By changing solvents with the same functions of ligands but of different coordinating abilities, a correlation between the kinetics and thermodynamics was observed. The nucleation rate increases with the metal precursor reactivity, which corresponds to stronger solvent binding to the precursor. On the other hand, the stronger ligand-nanoparticle binding slows down the growth by lowering the surface capping density. To go deeper into the ligand-metal binding and kinetics correlation, the binding properties were tuned by changing other synthesis conditions, i.e., different temperatures and ligand to metal ratios (ligand concentration), and a qualitative discussion was given on the effects of these conditions on the synthesis kinetics and final particle size.

De nos jours, les matériaux carbonés macroscopiques font face à un nombre croissant d'applications en catalyse, soit en tant que supports, soit directement en tant que catalyseurs sans métal. Cependant, il reste difficile de développer un support de catalyseur hiérarchisé à base de. carbone ou un catalyseur utilisant un procédé de synthèse beaucoup plus simple. À la recherche de nouveaux matériaux carbonés structurés pour la catalyse hétérogène, nous avons exploré le potentiel du feutre de carbone / graphite du commerce (FC / FG). Le but du travail décrit dans cette thèse a été le développement du monolithe FG et FC en tant que catalyseur sans métal pour les réactions d’oxydation en phase gazeuse et en tant que support de catalyseur, notamment pour le palladium, pour les réactions d’hydrogénation en phase liquide, et leur rôle dans la performance de réaction de ces catalyseurs. En raison de leur surface de chimie inerte avec une mouillabilité inappropriée, une telle étude avait pour condition d'activer celles d'origine. Par conséquent, des FG et des FC modifiés bien arrondis ont été synthétisés avec des propriétés physico-chimiques adaptées par une série de procédés de traitement chimique, tels que l'oxydation, l'amination, la thiolation, le dopage à l'azote et au soufre. L’oxydation partielle du sulfure d’hydrogène en soufre élémentaire et l’hydrogénation sélective du cinnamaldéhyde α, β-insaturé, en tant que réactions sensibles à l’effet des propriétés du catalyseur sur l’activité et la sélectivité, combinées à des techniques de caractérisation, ont été choisis pour étudier l’effet de la matériaux carbonés sur le comportement catalytique. / Nowadays, macroscopic carbon materials are facing an increasing number of applications in catalysis, either as supports or directly as metal-free catalysts on their own. However, it is still challenging to develop hierarchical carbon-based catalyst support or catalyst using a much simple synthesis process. In the quest for novel structured carbon materials for heterogeneous catalysis we explored the potential of commercial carbon/graphite felt (CF/GF). The aim of the work described in this thesis has been the development of GF and CF monolith as metal-free catalyst for gas-phase oxidation reactions and as catalyst support, notably for palladium, for liquid-phase hydrogenation reactions, and their roles in the reaction performance of these catalysts. Due to their inert chemistry surface with inappropriate wettability, a prerequisite for such a study was to activate the origin ones. Therefore, well-rounded modified GFs and CFs were synthesized with tailored physic-chemical properties by a series of chemical treatment processes, such as oxidation, amination, thiolation, nitrogen- and sulfur-doping. The partial oxidation of hydrogen sulfide into elemental sulfur and selective hydrogenation of α, β-unsaturated cinnamaldehyde, as the sensitive test reactions to the influence of the catalyst properties on activity and selectivity, combined with characterization techniques, were chosen to investigate the effect of functionalized carbon materials on the catalytic behavior.

Surfactant bound stable colloids of Au, Ag, and Pd were prepared by the solvated Metal Atom Dispersion (SMAD) method, a method involving co-condensation of metal and solvent vapors on the walls of a reactor at 77 k. The as=prepared dodecanethiol-capped Au and Ag colloids consisting of polydisperse nanoparticles were transformed into colloids consisting of highly monodisperse nanoparticles by the digestive ripening process. In the case of Pd colloids, digestive ripening led to the formation of thiolate complexes. The [Pd(SC12H25)2]6 complex formed from the dodecanethiol-capped Pd nanoparticles was found to be a versatile precursor for the synthesis of a variety of Pd nanophases such as Pd(0), PdS, and Pd@PdO by soventless thermolysis. Co-digestive ripening of as-prepared dodecanethiol-capped Au or Ag colloids with Pd colloid resulted in Au@Pd and Ag@Pd core-shell nanoparticles, respectively; attempts to transform the core-shell structures into alloy phases even at high temperatures were unsuccessful. Phosphine-capped Au nanoparticles were also prepared by the SMAD method and refluxing of this colloid resulted in an Ostwald ripening process rather than the expected digestive ripening due to the labile nature of bound PPh3. The labile nature of the bound phosphine was studied using 31P NMR spectroscopy and utilized in the adsorption of CO. Palladium nanoparticles obtained from the SMAD Pd-butanone colloids and Pd@PdO nanoparticles prepared by the solventless thermolysis of Pd-dodecanethiolate complex were found to be good catalysts for the generation of H2 from AB via either hydrolysis and methanolysis. The active hydrogen atoms produced during the hydrolysis and methanolysis diffuse into the Pd lattice. It was also noticed that hydrogen atoms that were buried deep inside the Pd lattice cannot be removed completely by heating the sample even at 600°C. Wet chemical reduction method was employed for the synthesis of PVP capped, nearly monodisperse, spherical Ir nanoparticles which undergo a polymer driven self-assembly at 80°C to afford rectangular structures and interlinked particles.