In modern wireless communication and radar systems, filters play an important role in getting a high-quality signal while rejecting spurious and neighboring unwanted signals. The filters with reconfigurable features, such as tunable bandwidths or switchable dual bands, also play a key part both in realizing the compact size of the system and in supporting multi-communication services. The Chapters II-IV of this dissertation show the studies of the filters for microwave communication. Bandpass filters realized in ring resonators with stepped impedance stubs are introduced. The effective locations of resonant frequencies and transmission zeros are analyzed, and harmonic suppression by interdigital-coupled feed lines is discussed. To vary mid-upper and mid-lower passband bandwidths separately, the characteristic impedances of the open-circuited stubs are changed. Simultaneous change of each width of the open-circuited stub results in variable passband bandwidths. Asymmetric stepped-impedance resonators are also used to develop independently controllable dual-band (2.4 and 5.2 GHz) bandpass filters. By extending feed lines, a transmission zero is created, which results in the suppression of the second resonance of 2.4-GHz resonators. To determine the precise transmission zeros, an external quality factor at feeders is fixed while extracting coupling coefficients between the resonators. Two kinds of feed lines, such as hook-type and spiral-type, are developed, and PIN diodes are controlled to achieve four states of switchable dual-band filters. Beam-scanning features of the antennas are very important in the radar systems. Phase shifters using piezoelectric transducers and dielectric leaky-wave antennas using metal strips are studied in the Chapters V-VII of this dissertation. Meandered microstrip lines are used to reduce the size of the phase shifters working up to 10 GHz, and reflection-type phase shifters using piezoelectric transducers are developed. A dielectric film with metal strips fed by an image line with a high dielectric constant is developed to obtain wide and symmetrical beam-steering angle. In short, many techniques are presented for realizing reconfigurable filters and large beam-scan features in this dissertation. The result of this work should have many applications in various wireless communication and radar systems.

This paper presents a novel power management analysis method to reduce the power consumption for the non-contact vital sign sensor. The sensor consisting of the class-E power amplifier (PA), low noise amplifier (LNA), single pole double through (SPDT) switch, and circularly polarized antenna (CPA) is integrated on the Flame Retardant Class 4 (FR-4) epoxy-glass laminate substrate. The appropriate pulse width and pulse period are determined to decrease the power consumption and accurately detect the human physiological signals (respiration and heartbeat). A simple direct down-conversion architecture with a tunable phase shifter is utilized to eliminate the null detection point and the direct current (DC) offset. The overall power consumption of the proposed sensor with the novel power management technique is only 40 % of the conventional system with the DC bias, which can be utilized for the green energy application.

In this thesis, we propose and demonstrate a simple and precise method for measuring mm scaled cell gap by using terahertz time domain spectroscopy (THz-TDS) system. This method allows us to measure the cell gap from 15mm to 1.5mm. In addition, the accuracy of measured thickness for the proposed method is also discussed and analyzed. Meanwhile, a nematic liquid crystal BL006 with birefringence as high as 0.27 in THz frequency range and its optical properties of cholesteric liquid crystal (CLC) as mixing chiral materials are investigated and reported. The ordinary refractive index and average effective refractive index at 20oC are from 1.52 to 1.56 and from 1.61 to 1.64, respectively, in THz frequency ranging from 0.2 THz to 1.4THz. In addition, we also demonstrate that cell filled with CLC is with polarization independent property for THz radiation. Through the 5mm cell filled CLC with diluted concentration of the dopant chiral material for decreasing the critical voltage, an electric controlled polarization independent phase shifter with the modulation depth exceeding 2pi is demonstrated. Furthermore, we also investigate the driving field dependence of phase retardation and discuss the reliability.

Modern phased array radars require large numbers of electronically controlled phase shifters to steer their beams to the desired direction. The amount of beam steering error depends on the phase resolution of the phase shifters as well as the performance of other parts of the antenna system. The size of the phase shifter in such systems is most of the time needed to be small, which necessitates the MMIC implementation. In the context of this thesis, an X band 7 bit MMIC phase shifter of 2.8125 degree phase resolution, including its layout, is designed using the design kit of OMMIC&reg / Foundry. All bits of the phase shifter are designed to have low return loss so as to minimize the performance egradation due to loading effects upon cascading. Also some structures studied using the design kit of WIN&reg / Foundry are presented. Both designs were performed using ADS&reg / . For the optimum cascading of 7 bits, a MATLAB code was written and used.

This thesis presents a novel monolithic phased array implemented using the RF MEMS technology. The structure, which is designed at 15 GHz, consists of four linearly placed microstrip patch antennas, 3-bit distributed RF MEMS low-loss phase shifters, and a corporate feed network. The RF MEMS phase shifter employed in the system consists of three sections with a total of 28 unit cells, and it occupies an area of 22.4 mm &amp / #61620 / 2.1 mm. The performance of the phase shifters is improved using high-Q metal-air-metal capacitors in addition to MEMS switches as loading elements on a high-impedance coplanar waveguide transmission line. The phased array is fabricated monolithically using an in-house surface micromachining process, where a 1.2-&amp / #61549 / m thick gold structural layer is placed on a 500-&micro / m thick glass substrate with a capacitive gap of 2 &amp / #61549 / m. The fabrication process is simple, requires only 6 masks, and allows the implementation of various RF MEMS components on the same substrate, such as RF MEMS switches and phase shifters. The fabricated monolithic phased array occupies an area of only 6 cm &amp / #61620 / 5 cm. The measurement results show that the phase shifter can provide nearly 20&amp / #61616 / /50&amp / #61616 / /95&amp / #61616 / phase shifts and their eight combinations at the expense of 1.5 dB average insertion loss at 15 GHz. The phase shifters can be actuated with 16 V, while dissipating negligible power due to its capacitive operation. It is also shown by measurements that the main beam can be steered to 4&amp / #61616 / and 14&amp / #61616 / by suitable settings of the RF MEMS phase shifters.

This thesis presents the theory, design, fabrication, and measurement results of novel reconfigurable impedance tuner, phase shifter, and vector modulators using the RF MEMS technology. The presented circuits are based on triple stub topology, and it is shown both theoretically and experimentally in this thesis that it is possible to control the insertion phase and amplitude of the input signal simultaneously using this topology. The presented circuits are implemented using an in-house, surface micromachining fabrication process developed at METU, namely METU RF MEMS Fabrication Process, which is implemented using six masks on quartz substrates. The RF MEMS impedance tuner is designed to operate in 6-20 GHz frequency band, and it covers the Smith Chart with 1331 impedance points. The measurement results of 729 impedance points of the fabricated impedance tuner show that a wide Smith Chart coverage is obtained in the entire band. The RF MEMS phase shifter is designed to cover 0-360 degrees range 10 degree steps at 15 GHz center frequency. The measurement results of the fabricated phase shifter show that the average phase error is 1.7 degrees, the average insertion loss is -3.1 dB, and the average return loss is -19.3 dB for the measured 21 phase states. The phase shifter can also work up to 30 GHz and 40 GHz with average insertion losses of -5 dB and -8 dB, respectively. The designed RF MEMS vector modulator operates in 22.5-27.5 GHz band, and it has 3 amplitude and 8 phase states. The measurement results of the fabricated vector modulator show that the amplitude error is 0.5 dB, the phase error is 4 degrees, and the return loss is -15 dB on average among the 24 measured states at each of 22.5, 25, and 27.5 GHz frequencies.

Microwave and millimeter-wave phase shifters are one of the most important structures of the antenna series that are used in communication and radar applications. They are used to form the main beam of the electronically scanned phase array antennas and generate the appropriate phase values for the antenna elements design while providing electronic beam steering. In this thesis, S-band hybrid 4 bit phase shifter of 22.5&ordm / phase resolution is designed, simulated, fabricated and measured. Bits are separately designed to maintain low phase errors and return loss. In this manner, fabrication and measurements are performed for each bit. These measurements are carried on since each bit reached to its acceptable level of operation. According to the outcomes and acquired knowledge, layout for optimum cascading of 4 bits is developed. Measurement results are compared with simulations and repeatability is tested to observe if it is convenient to use in mass production. Designs and simulations are performed by using ADS2008&reg / .

L’objectif de ces travaux de recherche est la conception en technologie intégrée d’une nouvelle topologie de ligne de transmission accordable afin de réaliser des déphaseurs en bande millimétrique. Cette topologie nommée TS-CPW (pour « Tunable Slow wave CoPlanar Waveguide ») utilise d’une part le phénomène d’ondes lentes qui permet de miniaturiser longitudinalement la ligne de transmission et offre un facteur de qualité plus élevé qu’en technologie microruban intégrée, et d’autre part une approche de type MEMS (Micro Electro Mechanical system) afin obtenir l’accordabilité de la ligne avec une figure de mérite élevée comparativement à une approche de type varactor. Dans un premier temps, la topologie et la conception d’une ligne TS-CPW basée sur des simulations électromagnétiques sont présentées en technologie BiCMOS. Dans un second temps, toujours sur la base de TS-CPWs, des déphaseurs présentant 3-bit de résolution, avec différentes valeurs de déphasage total (de 157.5° et 315°), ont été développés à une fréquence de fonctionnement égale à 60 GHz. Les TS-CPWs et les déphaseurs ont été réalisés avec la technologie BiCMOS 0.25 µm de l’institut IHP en Allemagne, puis mesurés à l’aide d’un analyseur de réseau à IHP et à l’IMEP-LaHc. / This work focuses on the design of millimeter-wave phase shifters based on a new topology of tunable transmission lines named Tunable Slow wave CoPlanar Waveguide (TS-CPW). TS-CPW uses, on one side, the slow wave phenomenon in order to miniaturize longitudinally the transmission line and to show a better quality factor than its integrated microstrip transmission line counterpart and, on the other side, the MEMS approach to achieve tunability of the transmission line with a good figure-of-merit. First, the topology, the design and the electromagnetic simulations of the TS-CPW based on MEMS (Micro Electro Mechanical system) are presented in a BiCMOS technology. Next, phase shifters with 3-bit of resolution based on TS-CPWs are developed at 60 GHz with two different values of total phase shift (157.5° and 315°). These TS-CPWs and phase shifters were fabricated in IHP’s 0.25 µm BiCMOS technology and measured on the vector network analyzers of IHP and IMEP-LaHC.

The capacity of optical communications networks continues to grow unabated. Applications for streaming video, social networking and cloud computing, are driving exponential growth of the traffic carried over the world’s ICT networks, which has been sustained thus far through the proliferation of datacenters and efficient, effective use of existing optical fibre. To meet increasing capacity demands requires increasingly sophisticated modulation formats and spectral management to achieve effective use of the available spectrum provided by an optical fibre. Moreover, the technology developed for optical communications is finding broader application to other sectors such as data centres, 5&6 G wireless; lidar and radar. Ultimately, some essential signal processing functions must occur at speeds beyond purely electronic means even when accounting for anticipated technological development. The option is to perform signal processing in the optical domain. Optical signal processors are fundamentally analog and linear in nature. To provide high performance, an analogue processor must be well controlled in a way analogous to the numerous and sophisticated controllers employed by the process industry. Consequently, a further extension of control to deeper levels within the physical layer reaching the optical layer will be necessary. For example, current reconfigurable optical add-drop multiplexers are coloured and directional and the wavelength division multiplexing channel grid, transponders modulation format, and the routing are all fixed. Through optimization of the interface between the physical components, sensors, and processors elastic optical network technology can be achieved by employing colour-, direction-, contention-, grid-less, filter-, gap-less reconfigurable optical add-drop multiplexers, flexible channels centre frequencies and width, flexible sub-carriers in super-channels, flexible modulation formats and forward error control coding transponders, and impairment-aware wavelength routing and spectral assignment. The aim of this thesis is to advance the state-of-the-art in photonic circuits and subsystems via proposing new architecture; study of the feasibility of photonic integration and, proof of concept implementations using available resources. The goal is to introduce new architectural concepts that make effective use of physical components and/or optical processors with reduced energy consumption, reduced footprint and offer speed beyond all-electronic implementations. The thesis presents four case studies based on one or more published papers and supplementary material that advance the goal of the thesis. The first study presents a coherent electro-optic circuit architecture that generates N spatially distinct phase-correlated harmonically related carriers using a generalized Mach-Zehnder Interferometer with its N×1 combiner replaced by an N×N optical Discrete Fourier Transform. The architecture subsumes all Mach-Zehnder Interferometer-based architectures in the prior art given an appropriate selection of output port(s) and dimension N, although the principal application envisaged is phase-correlated subcarrier generation for next-generation optical transmission systems. The theoretical prediction is then verified experimentally using laboratory available photonic integrated circuit fabricated for other applications. Later on, a novel extension of the circuit architecture is introduced by replacing the optical Discrete Fourier Transform network using the combination of a properly chosen phase shifter and single MMI coupler. The second study proposes two novel architectures for an on-chip ultra-high-resolution panoramic spectrometer and presents their design, analysis, integration feasibility, and verification by simulation. The target application is to monitor the power of a wavelength division multiplexed signals in both fixed and flex grid over entire C-band with minimum scan time and better than 1 GHz frequency accuracy. The two architectures combine in synchrony a scanning comb filter stage and channelized coarse filter. The fine filtering is obtained using a ring resonator while the coarse filtering is obtained using an arrayed waveguide grating with appropriate configuration. The fully coherent first architecture is optimised for compactness but relies on a repeatable fabrication processes to match the optical path lengths between a Mach-Zehnder interferometer and a multiple input arrayed waveguide grating. The second architecture is less compact than the first but is robust to fabrication tolerances as it does not require the path length matching. The third study proposes a new circuit architecture for single sideband modulation or frequency conversion which employs a cascade Mach-Zehnder modulator architecture departing from the orthodox dual parallel solution. The theoretical analysis shows that the circuit has 3-dB optical and 3-dB electrical advantage over the orthodox solution. The 3-dB electrical advantage increases the linear operating range of Mach-Zehnder modulator before RF amplifier saturation. An experimental verification of the proposed architecture is provided using an available photonic integrated circuit. The proposed circuit can also perform complex modulation. An alternative implementation based on polarization modulators is also described. The fourth study presents the theoretical modelling of a photonic generation of broadband radio frequency phase shifter. The proposed phase shifter can generate any phase without bound: the complex transmission of the phase shifter follows a trajectory that rotates on a unit circle and may encircle the origin any number of times in either direction, which has great utility in the tuning of RF-photonic systems. The proposed concept is then verified experimentally using off the shelf low frequency electronic components.

No description available.