For grafting polypyrrole on oxidized surfaces, 3-substituted pyrrole alkyl phosphonic acids, 11-(pyrrol-3-yl undecyl) trimethoxysilanes and 1-substituted pyrrole alkyl organosilanes with different chain length were designed and successfully synthesized as adhesion promoters. These new derivatives were studied for their adsorption behavior on oxide substrates and chemical or electrochemical deposition of polypyrrole over modified oxide surface or electrodes. Several analytical techniques such as contact angle measurement, surface plasmon resonance spectroscopy (SPR), UV-VIS Spectroscopy, grazing incident FTIR, X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and atomic force microscopy (AFM) were employed to characterize the adsorbed layers on different substrates. Contact angle measurement and ellipsometry data showed that high concentrations in apolar hydrocarbon solvent and long reaction times are sufficient to form tightly packed monolayer of 1-substituted pyrrole alkyl monochlorosilanes (PMCS) on substrates. Adsorption kinetics were studied by SPR and showed that the adsorption took place within a few seconds, then continuously increased and reached a plateau. The orientation of these synthesized monomers is investigated to be well-suited for use as adhesion promoter. CV-measurements showed that 3-substrated pyrrole derivatives had lower oxidation potential, whereas 1-substituted pyrrole derivatives had higher oxidation potential compared with pyrrole. Surface deposition of polypyrrole on the adhesion promoter modified (silane-modified and phosphonic acid-modified) substrates by chemical and electrochemical polymerization were investigated. PPy films formed on the modified surfaces by surface chemical polymerization showed a better adhesion compared to those on the unmodified surfaces. The morphology of PPy films was influenced by the alkyl chain length of the adhesion promoter and the deposition condition, such as choice of oxidant and solvent. The thickness of the resulting PPy films were controlled by the polymerization conditions, such as choice of solvent, deposition time, pyrrole to oxidant ratio and monomer concentration. The thickness of the deposited PPy film was estimated in the range of 10-400 nm by AFM and ellipsometry. The electrical properties were studied by current-voltage (j-V) measurement. Temperature dependence of j-V characteristics of Si/SiO2/PPy/PMCS-16/Al films revealed that the current increases with temperature, the film shows a typical semiconductor behavior. The use of these adhesion promoters modified electrode for electrochemical polymerization resulted in adhesive polypyrrole films.Also the 3-substituted pyrrole phosphonic acids were found to be homo-and co-polymerizable (with pyrrole) under chemical methods. TGA showed that homopolymers are less stable than polypyrrole due to the 3-substitution. he homopolymer of 3-substituted phosphonic acid derivatives of pyrrole is soluble. Films coated from the MeOH solution of homopolymer could be successfully used as humidity sensors. It is observed that the resistivity of the 3-substituted homopolypyrrole sensors increases and capacitance decreases during exposure to humid air. The polypyrrole films obtained by surface chemical polymerization was also used as humidity sensors.

The goal of the work described in this dissertation was to investigate the structure of metal phosphonate frameworks which were composed of conforma-tionally flexible ligands. This goal was achieved through investigating new syn-thetic techniques, systematically changing structural aspects (i.e. chain length), and conducting in situ X-ray diffraction experiments under non-ambient condi-tions. First, the use of ionic liquids in the synthesis of metal phosphonates was in-vestigated. Reaction systems which had previously been studied in purely aqueous synthetic media were reinvestigated with the addition of a hydrophobic ionic liq-uid to the reaction. Second, the structural diversity of zinc alkylbisphosphonates was investigated through systematically varying the chain length and reaction conditions. Last, the structural changes associated with externally applied stimuli (namely temperature and pressure) on conformationally flexible metal phospho-nates were investigated. Elevated temperature was used to investigate the structur-al changes of a 1-D cobalt chain compound through three stages of dehydration and also applied pressures of up to 10 GPa were used to probe the structural resili-ence of two zinc alkylbisphosphonate materials under. The iminobis(methylphosphonic acid) type ligands are a good example of a small, simple, conformationally flexible ligand. There are three distinct different structural types, utilizing this ligand with cobalt metal, described in the literature, all of which contain bound or solvated water molecules. The addition of a hydrophobic ionic liquid to an aqueous synthesis medium resulted in new anhydrous compounds with unique structural features. Systematic investigations of zinc alkylbisphosphonate materials, construct-ed with three to six carbon linker ligands, resulted in four new families of com-pounds. Each of these families has unique structural features which may prove in-teresting in future applications developments. Importantly, it is shown that wheth-er the chain length is odd or even plays a role in structural type although it is not necessarily a requirement for a given structural type; furthermore, chain length itself is not strictly determinative of structural type. Dehydration in a cobalt phosphonate was followed via in situ single crystal X-ray diffraction. The compound goes through a two-stage dehydration mecha-nism in which the compound changes from a 1-D chain to a 2-D sheet. This pro-cess is reversible and shows unique switchable magnetic properties. The high pressure studies of an alkyl chain built zinc metal phosphonate showed that the chains provide a spring-like cushion to stabilize the compression of the system allowing for large distortions in the metal coordination environment, without destruction of the material. This intriguing observation raises questions as to whether or not these types of materials may play a role as a new class of piezo-functional solid-state materials.

For grafting polypyrrole on oxidized surfaces, 3-substituted pyrrole alkyl phosphonic acids, 11-(pyrrol-3-yl undecyl) trimethoxysilanes and 1-substituted pyrrole alkyl organosilanes with different chain length were designed and successfully synthesized as adhesion promoters. These new derivatives were studied for their adsorption behavior on oxide substrates and chemical or electrochemical deposition of polypyrrole over modified oxide surface or electrodes. Several analytical techniques such as contact angle measurement, surface plasmon resonance spectroscopy (SPR), UV-VIS Spectroscopy, grazing incident FTIR, X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and atomic force microscopy (AFM) were employed to characterize the adsorbed layers on different substrates. Contact angle measurement and ellipsometry data showed that high concentrations in apolar hydrocarbon solvent and long reaction times are sufficient to form tightly packed monolayer of 1-substituted pyrrole alkyl monochlorosilanes (PMCS) on substrates. Adsorption kinetics were studied by SPR and showed that the adsorption took place within a few seconds, then continuously increased and reached a plateau. The orientation of these synthesized monomers is investigated to be well-suited for use as adhesion promoter. CV-measurements showed that 3-substrated pyrrole derivatives had lower oxidation potential, whereas 1-substituted pyrrole derivatives had higher oxidation potential compared with pyrrole. Surface deposition of polypyrrole on the adhesion promoter modified (silane-modified and phosphonic acid-modified) substrates by chemical and electrochemical polymerization were investigated. PPy films formed on the modified surfaces by surface chemical polymerization showed a better adhesion compared to those on the unmodified surfaces. The morphology of PPy films was influenced by the alkyl chain length of the adhesion promoter and the deposition condition, such as choice of oxidant and solvent. The thickness of the resulting PPy films were controlled by the polymerization conditions, such as choice of solvent, deposition time, pyrrole to oxidant ratio and monomer concentration. The thickness of the deposited PPy film was estimated in the range of 10-400 nm by AFM and ellipsometry. The electrical properties were studied by current-voltage (j-V) measurement. Temperature dependence of j-V characteristics of Si/SiO2/PPy/PMCS-16/Al films revealed that the current increases with temperature, the film shows a typical semiconductor behavior. The use of these adhesion promoters modified electrode for electrochemical polymerization resulted in adhesive polypyrrole films.Also the 3-substituted pyrrole phosphonic acids were found to be homo-and co-polymerizable (with pyrrole) under chemical methods. TGA showed that homopolymers are less stable than polypyrrole due to the 3-substitution. he homopolymer of 3-substituted phosphonic acid derivatives of pyrrole is soluble. Films coated from the MeOH solution of homopolymer could be successfully used as humidity sensors. It is observed that the resistivity of the 3-substituted homopolypyrrole sensors increases and capacitance decreases during exposure to humid air. The polypyrrole films obtained by surface chemical polymerization was also used as humidity sensors.

Nano-structured materials are widely applied for various applications like photovoltaics, electrochromics and sensors. A challenging task in all these fields is the functionalization of these materials with a molecule of interest for the desired application. This work demonstrate the post grafting of the most important and commonly used nano-structured material, mesoporous TiO2, with different bifunctional molecular linkers. These compounds basically have two functional groups, the phosphonic acid group which coordinates to the TiO2 surface and a positive and negative head group which controls the surface charge and the potential interaction of the surface with species in solution. These two groups are systematically separated by alkyl group of different chain length which controls the hydrophobicity of the surface. It is shown that the new surface modification technique simplifies the molecular requirements for functional surface modifiers considerably. Using a limited set of organic anchors with adjustable head group charge and hydrophobicity, broad range of molecules can be adsorbed onto TiO2. Different applications based on such modified surfaces were explored and demonstrated. The modified surfaces can be used to incorporate different charged guest molecules, electrochromophores and dyes which enable to probe their electrochemistry and photovoltaic properties on the surface. Supra-molecular self assembly inside the modified pores is possible which can be monitored by different methods. The study includes the prepartaion of the modified surfaces and their characterization using different electrochemical methods, FTIR spectroscopy, Quartz Crystal Microbalance, Contact angle and Scanning Electron Microscopy measurements.

This thesis focuses on the use of surface modifiers to tune the properties of both metals and metal oxides. Particular attention is given to examine the modification of transparent conducting oxides (TCOs) including indium tin oxide and zinc oxide both through the use of phosphonic acids as well as organic and metal-organic dopants. In this thesis a variety of known and new phosphonic acids are synthesized. A subset of these molecules are then used to probe the relationship between the ability of a phosphonic acid to tune the work function of ITO and how that interrelates with the coverage and molecular orientation of the modifier on the surface. Experimental techniques including XPS, UPS, and NEXAFS are coupled with theoretical DFT calculations in order to more closely examine this relationship. Literature surrounding the modification of zinc oxide with phosphonic acids is not as prevalent as that found for the modification of ITO. Thus, effort is placed on attempting to determine optimal modification conditions for phosphonic acids on zinc oxide. As zinc oxide is already a low work function metal oxide, modifiers were synthesized in an attempt to further decrease the work function of this substrate in an effort to minimize the barrier to carrier collection/injection. Etching of the substrate by phosphonic acids is also examined. In a related technique, n- and p-dopants are used to modify the surfaces of ITO, zinc oxide, and gold and it was found that the work function can be drastically altered, to approximately 3.3 – 3.6 eV for all three of the substrates examined. Surface reactions are straightforward to conduct typically taking only 60 s to achieve this change in work function.

Thesis (Ph.D.); Submitted to the University of California at Berkeley, Berkeley, CA (US); 1 Sep 2003. / Published through the Information Bridge: DOE Scientific and Technical Information. "LBNL--55023" Li, Liang-shi. USDOE Director. Office of Science. Office of Basic Energy Sciences (US) 09/01/2003. Report is also available in paper and microfiche from NTIS.

Porous metal phosphonate framework materials were synthesised by solvothermal reaction of bis(α-aminomethylenephosphonic acid) ligands with divalent and trivalent metal cations. The syntheses and characterisation by NMR and, where possible, single crystal X-ray diffraction of seven bisphosphonic acid ligands, including N,N′-piperazinebis(methylenephosphonic acid) (H₄L), its racemic and enantiopure (R) 2-methyl (H₄L′ and R-H₄L′) and 2,5-dimethyl (H₄L′′) derivatives, and N,N′-4,4′-bipiperidinebis(methylenephosphonic acid) (H₄LL) are reported. Syntheses of the known phase Y₂(LH₂)₃·5H₂O and the new phases, STA-13(Y) (St Andrews microporous material No. 13) and Y₂(R-L′H₂)₃·4H₂O, from reactions of Y(AcO)₃ with H₄L, H₄L′ and R-H₄L′ respectively are reported. The as-prepared and dehydrated structures of each phase have been determined from either laboratory or synchrotron powder X-ray diffraction data. Reaction of Y(AcO)₃ and H₄L′′ is shown to form a phase with a different structure. The features determining which structure crystallises are discussed. Syntheses of other rare-earth forms of STA-13 (Sc³⁺, Gd³⁺–Yb³⁺) and the porosity of each phase to N₂ are reported. STA-13(Y) is the most porous form with loadings of ∼3 mmol g⁻¹ and ∼4 mmol g⁻¹ for N₂ and CO₂ respectively. MIL-91(Fe) was synthesised for the first time from reactions of Fe³⁺ cations with H₄L. Its structure was confirmed by Rietveld refinement, but it was not porous. The first syntheses of [Fe₄L₁.₅(AcO)₁.₅(OH,H₂O)₃]·0.5NH₄5.5H₂O (L= L or L′) are reported, from reactions of H₄L or H₄L′ in the presence of an excess of Fe³⁺ cations. The phase is related to a previously reported Co phase. The synthesis of divalent metal bisphosphonate STA-12(Mg) (Mg₂(H₂O)₂L·5.6H₂O) was reported for the first time and its structure determined from single crystal X-ray diffraction. The dehydration behaviour of this material was compared with the known forms of STA-12. STA-12(Mg) is porous to both N₂ (∼5.5 mmol g⁻¹) and CO₂ (~ 8.5 mmol g⁻¹). Reaction of H₄LL with Co²⁺ and Ni²⁺ gave two materials isoreticular with STA-12, labelled STA-16(Co) and STA-16(Ni). The structures of both materials were solved from synchrotron powder X-ray diffraction data. On dehydration, STA-16(Co) undergoes a reversible structural transition to an unknown structure. By contrast, STA-16(Ni) retains the same symmetry in the dehydrated form and its structure was determined from synchrotron powder X-ray diffraction data. Both materials are porous to N₂, with an uptake of up to 22.2 mmol g⁻¹, and CO₂ with maximum loading of 21.7 mmol g⁻¹. NLDFT analysis of N₂ adsorption data confirm the crystallographically determined pore radii. Syntheses of other frameworks with divalent cations and initial reactions of H₄LL with trivalent cations are also reported.

Les dispersions colloïdales de nanoparticules (NPs) sont très répandues dans l'industrie, et permettent d'éviter l'utilisation de NPs sèches, controversée pour des raisons de toxicité. Le contrôle des interactions entre les NPs et le milieu dispersant reste le point clé de ces systèmes. La modulation de ces interactions permet de contrôler l'état de dispersion des NPs dans les sols. De plus, les nanocomposites NPs-polymère se sont avérés prometteurs pour une large gamme d'applications, ainsi l'utilisation de sols pourrait présenter une voie avantageuse d'incorporation des NPs dans le polymère, tout en offrant la possibilité de contrôler leur état de dispersion, et in fine les propriétés du matériau, celles-ci étant liées à l'état de dispersion des NPs. L'objectif de ce travail de thèse est le développement de méthodes de modification de surface de NPs d'oxyde en dispersion colloïdale, tout en contrôlant la dispersion des NPs dans les sols et dans les nanocomposites issus de ces sols. Puis, l'évaluation de cet état de dispersion par SAXS. Deux méthodes de modification de surface ont ainsi été développées : la première implique le greffage d'acides phosphoniques sur des NPs de silice recouvertes d'alumine en dispersion dans l'eau, et la seconde met en jeu le greffage d'acides phosphoniques sur des NPs de TiO2 et leur transfert d'une phase aqueuse à une phase CHCl3. Les NPs modifiées ont été caractérisées par diverses méthodes. Leur état de dispersion a été étudié par DLS et SAS. De plus, pour les NPs de silice-amine, l'impact de la densité de greffage du C8PA sur la structure des NPs (à l'état sec) a été mis en évidence par SAXS et différents processus de relaxation ont été étudiés par BDS pour les NPs nues et modifiées. Enfin, ces NPs ont été incorporées dans un polymère de PEA par voie aqueuse via des latex et leur état de dispersion dans les composites a été mesuré par SANS. / Colloidal nanoparticles (NPs) dispersions are largely used in the industry, and avoid the use of dried NPs, which is controversial due to safety concerns. The key point in such systems remains the control of the interactions with the dispersed medium and between the NPs. Mastering these interactions allows controlling the NPs' state of dispersion. Moreover, as polymer-NPs nanocomposites have been found promising for a wide variety of applications, the use of colloidal sols could thus be an advantageous way of NPs' incorporation in the polymer, with a possible control of the NPs state of dispersion, and finally on the properties of the material, as they are linked to the NPs' dispersion. The purpose of this PhD work is to develop surface-functionalization methods of oxide NPs in colloidal sols in order to control the dispersion of NPs in the sols and in polymer nanocomposites derived from these sols, and to evaluate this dispersion using SAXS. Two surface modification methods have been developed to obtain aqueous or organic sols of functionalized NPs. The first one concerns the reaction in water of alumina-coated silica NPs with phosphonic acids (PAs), and the second one involves the simultaneous grafting and phase transfer of TiO2 NPs from an aqueous to a CHCl3 phase using PAs. The resulting NPs were characterized and their state of dispersion was monitored by DLS and SAS measurements. The impact of the C8PA grafting density on the structure of modified alumina-coated silica NPs in the dried state was evidenced by SAXS. The different relaxation processes of bare and grafted NPs were studied by BDS. These NPs were then incorporated in a PEA polymer by an aqueous latex route, and their structure in the nanocomposites was investigated by SANS.