京都大学 / 0048 / 新制・課程博士 / 博士(工学) / 甲第20579号 / 工博第4359号 / 新制||工||1678(附属図書館) / 京都大学大学院工学研究科物質エネルギー化学専攻 / (主査)教授 安部 武志, 教授 作花 哲夫, 教授 河瀬 元明 / 学位規則第4条第1項該当 / Doctor of Philosophy (Engineering) / Kyoto University / DGAM

No description available.

Polymer electrolyte membrane fuel cells (PEMFCs) have recently acquired much attention as alternatives to combustion engines for power conversion. The primary interest in fuel cell technology is the possibility of 60% power conversion efficiency as compared to the 30% maximum theoretical efficiency limited to combustion engines and turbines. Although originally conceived to work with hydrogen as a fuel, difficulties relating to hydrogen storage have prompted much effort in using other fuels. Small organic molecules such as alcohols and formic acid have shown promise as alternatives to hydrogen in PEMFCs due to their higher stability at ambient conditions. The drawbacks for using these fuels in PEMFCs are related to their incomplete oxidation mechanisms, which lead to the production of carbon monoxide (CO). When carbon monoxide is released in fuel cells it binds strongly to the platinum anode thus limiting the adsorption and subsequent oxidation of more fuel. In order to promote the complete oxidation of fuels and limit poisoning due to CO, various metal and metal oxide catalysts have been used. Motivated by promising results seen in fuel cell catalysis, this research project is focused on the design and fabrication of novel platinum-composite catalysts for the electrooxidation of methanol, ethanol and formic acid. Various Pt-composites were fabricated including Pt-Au, PtRu, Pt-Pd and Pt-CeO2 catalysts. Electrochemical techniques were used to determine the catalytic ability of each novel composite toward the electrooxidation of methanol, ethanol and formic acid. This study indicates that the novel composites all have higher catalytic ability than bare Pt electrodes. The increase in catalytic ability is mostly attributed to the increase in CO poison tolerance and promotion of the complete oxidation mechanism of methanol, ethanol and iv formic acid. Formulations including bi- and tri-composite catalysts were fabricated and in many cases show the highest catalytic oxidation, suggesting tertiary catalytic effects. The combination of bi-metallic composites with ceria also showed highly increased catalytic oxidation ability. The following dissertation expounds on the relationship between composite material and the electrooxidation of methanol, ethanol and formic acid. The full electrochemical and material characterization of each composite electrode is provided.

The first part of the study deals with the preparation of carbon nanotube/polymer nanocomposite materials. The dispersion of multi-walled carbon nanotubes (MWNTs) using trifluoroacetic acid (TFA) as a co-solvent and its subsequent use in polymer nanocomposite fabrication is reported. The use of carbon nanotube/ polymer nanocomposite system for the fabrication of organic solar cells is also studied. TFA is a strong but volatile acid which is miscible with many commonly used organic solvents. Our study demonstrates that MWNTs can be effectively purified and readily dispersed in a range of organic solvents including dimethyl formamide (DMF), tetrahydrofuran (THF), and dichloromethane when mixed with 10 vol% trifluoroacetic acid (TFA). X-ray photoelectron spectroscopic analysis revealed that the chemical structure of the TFA-treated MWNTs remained intact without oxidation. The dispersed carbon nanotubes in TFA/THF solution were mixed with poly(methyl methacrylate) (PMMA) to fabricate polymer nanocomposites. A good dispersion of nanotubes in solution and in polymer matrices was observed and confirmed by SEM and optical microscopy study. Low percolation thresholds of electrical conductivity were observed from the fabricated MWNT/PMMA composite films. A carbon nanotube/ polymer nanocomposites system was also used for the fabrication of organic solar cells. A blend of single-wall carbon nanotubes (SWNTs) and poly3-hexylthiophene (P3HT) was used as the active layer in the device. The device characteristics showed that the fabrication of the solar cells was successful without any shorts in the circuit. The second part of the study deals with the preparation and characterization of electrode and electrolyte materials for lithium ion batteries. A system of lithium trifluoroacetate/ PMMA was used for its study as the electrolyte in lithium battery. A variety of different processing conditions were used to prepare the polymer electrolyte system. The conductivity of the electrolyte plays a critical role in the high power output of a battery. A high power output requires fast transport of lithium ions for which the conductivity of the electrolyte must be at least 3 x 10^-4 S/cm. Electrochemical Impedance Spectroscopy (EIS) was used to determine the conductivity of the polymer electrolyte films. Among the different processing conditions used to prepare the polymer electrolyte material, wet films of PMMA/salt system prepared by using 10vol% of TFA in THF showed the best results. At about 70wt% loading of the salt in the polymer, the conductivity obtained was about 1.1 x 10^-2 S/cm. Recently, the use of vanadium oxide material as intercalation host for lithium has gained widespread attention. Sol-gel derived vanadium oxide films were prepared and its use as a cathode material for lithium ion battery was studied. The application of carbon nanotubes in lithium ion battery was explored. A carbon nanotube /block copolymer (P3HT-b-PS) composite was prepared and its potential as an anode material was evaluated.

京都大学 / 新制・課程博士 / 博士(工学) / 甲第24644号 / 工博第5150号 / 新制||工||1983(附属図書館) / 京都大学大学院工学研究科化学工学専攻 / (主査)教授 河瀬 元明, 准教授 中川 浩行, 教授 外輪 健一郎 / 学位規則第4条第1項該当 / Doctor of Philosophy (Engineering) / Kyoto University / DFAM

The majority of this dissertation focuses on proton conducting materials that could be used at high operating temperatures. Higher operating temperatures are desirable as they will increase fuel cell efficiency, reduce cost, and simplify the heat management system. The factors governing proton conduction including segmental mobility, protogenic group identity, and charge carrier density were investigated on a variety of polymers containing 1H-1,2,3-triazole moieties. Proton conductivity measurements were made using AC impedance spectroscopy. Random copolymers and terpolymers of triazole-containing acrylates and poly(ethylene glycol)methyl ether acrylate (PEGMEA) have been synthesized. Conductivity increased with increasing degree of PEG incorporation until reaching a maximum at 30% mole PEGMEA. In comparison to benzimidazole-functionalized polyacrylate with 35% mole PEGMEA, the triazole analog showed a higher proton conductivity, and a less pronounced conductivity temperature dependence. Further increases in conductivity was achieved through the addition of trifluoroacetic acid. To study the effect of charge carrier density on proton conduction, polyacrylates containing a different number of triazole groups per repeat unit were synthesized. The result showed that introduction of more than one triazole per repeat unit did not result in an increase in conductivity as there was an accompanying increase in Tg. To improve the thermal and mechanical properties, triazole groups were tethered to a higher Tg backbone polymer, polynorbornene. Introduction of polyhedral oligomeric silsesquioxane (POSS) into triazole-functionalized polynorbornene was also investigated. In a parallel set of investigations, poly(2-(dimethylamino)ethyl methacrylate), PDMAEMA, and copolymers of DMAEMA and methyl methacrylate (PDMAEMA-co-PMMA) were synthesized via atom transfer radical polymerization (ATRP). Fluorescently-labeled PDMAEMAs were synthesized using fluorescent ATRP initiators to ensure the presence of one dye molecule on every polymer chain. PDMAEMAs and PDMAEMA-co-PMMA with different molecular weights have been deposited onto a negatively-charged silica surface via controlled flow deposition. The results show that the polymer deposition rate depends on molecular weight, and is inversely proportional to molecular weight. A preliminary adhesion study of 1-μm negatively charged silica spheres onto these functionalized surfaces indicates that by varying the molecular weight, the adhesion threshold can be changed. System modeling is being conducted to support experimental observations.

Anhydrous proton conducting polymers are highly sought after for applications in high temperature polymer electrolyte membrane fuel cells (PEMFCs). N-heterocycles (eg. imidazole, triazole, and benzimidazole), owing to their amphoteric nature, have been widely studied to develop efficient anhydrous proton transporting polymers. The proton conductivity of N-heterocyclic polymers is influenced by several factors and the design and development of polymers with a delicate balance among various synergistic and competing factors to provide appreciable proton conductivities has been a challenging task. In this thesis, the proton transport (PT) characteristics of polymers functionalized with two diverse classes of functional groups - N-heterocycles and phenols have been investigated and efforts have been made to develop the molecular design criteria for the design and development of efficient proton transporting functional groups and polymers. The proton conduction pathway in 1H-1,2,3-triazole polymers is probed by employing structurally analogous N-heterocyclic (triazole, imidazole, and pyrazole) and benz-N-heterocyclic (benzotriazole, benzimidazole, and benzopyrazole) polymers. Imidazole-like pathway was found to dominate the proton conductivity of triazole and pyrazole-like pathway makes only a negligible contribution, if any. Polymers containing benz-N-heterocycles exhibited higher proton conductivity than those with the corresponding N-heterocycles. Pyrazole-like functional groups, i.e. the molecules with two nitrogen atoms adjacent to each other, were found not to be good candidates for PT applications. A new class of proton transporting functional groups, phenols, has been introduced for anhydrous PT. One of the highlighting features of phenols over N-heterocycles is that the hydrogen bond donor/acceptor reorientation can happen on a single -OH site, allowing for facile reorientational dynamics in Grotthuss PT and enhanced proton conductivities in phenolic polymers. Unlike the case of N-heterocycles, comparable conductivities were achieved between poly (3,4,5-trihydroxy) styrene and the corresponding small molecule, pyrogallol. This observation suggests that reorientation should be considered as a crucial design parameter for PT functional groups. The PT characteristics of phenol-based biaryl polymers are studied and compared with the analogous phenol-based linear styrenic polymers. The two-dimensional disposition of -OH moieties in biaryl polymers, although resulted in lower apparent activation energies (Ea), did not improve the net proton conductivity due to the accompanying increase in glass transition temperature (Tg). Thus, the ease of synthesis and lower Tg values of phenol-based styrene polymers make the styrenic polymer architecture preferable over the biaryl architecture. Finally, the synthesis of a series of poly(3,4-dihydroxy styrene)-b-polystyrene block copolymers has been demonstrated via anionic polymerization. These block copolymers will provide an opportunity to systematically investigate the effect of nanoscale morphology on proton transport.

No description available.

No description available.

No description available.