Power line communications (PLC) as applied to electrical power grid is known since long; however, PLC in microprocessors was recently introduced by VTVT Lab. Since power distribution network (PDN) inside a microprocessor is ubiquitous, therefore, any node inside a microprocessor can be accessed by attaching a simple communication circuit to it. The scheme is extremely attractive as it avoids the routing overhead of the data-path between an internal node and an I/O pin. A number of applications are possible for PLC in microprocessors such as on-line testing, monitoring/control of internal nodes, fault diagnosis etc. Feasibility of the PLC approach has been extensively studied by earlier researchers at VTVT. The feasibility studies investigated the frequency response of a microprocessor's PDN and looked for existence of passbands — frequency bands where signal attenuation through the PDN is small. Two different approaches were followed—the first approach employed analytical modeling of the high frequency characteristics of the PDN, while the second approach conducted measurements on Intel® microprocessors' PDN. Although, differences were observed in the results of the two approaches; both the approaches demonstrated existence of passbands, thus affirming the feasibility of the PLC scheme. This thesis presents a system level study conducted to estimate performance of the PLC scheme. Measurement results were used to model the PDN channel. The study provides useful insights for the design of microprocessor level PLC system. Specifically, the study estimates optimal pulse width required to maximize the system performance and the range of achievable data-rates. The study demonstrates that it is feasible to communicate data through a microprocessor's PDN without inducing large disturbances on the power line. The other work presented in this thesis is the design of low power receiver for microprocessor level PLC, also called data recovery block. The proposed design of data recovery block employs Correlation Detection (CD) receiver architecture. The design has been implemented in IBM 0.13 µm CMOS process and has been verified to operate reliably across Process, Voltage and Temperature variations. The design has a small foot-print of 300 µm x 160 µm and consumes 3.58 mW while operating from 1.2 V power supply. / Master of Science

A project submitted to the faculty of Engineering, University of the Witwatersrand, Johannesburg, in partial fulfilments of the requirements for the degree of Master of science in Engineering Johannesburg, 1994 / The purpose of this document is to report on the development of Linear Programming function for the Generation Expansion Planning environment of Eskom. This was achieved by researching the modeling methods employed in this and related fields of work. After establishing the scope of the work to be performed all the options were carefully assessed and it was decided to develop the Production Scheduling function first, as this would serve as the foundation for future work. The requirements were specified after extensive discussion with the customer. These requirements were utilize to establish the formulae, including their bounds and constraints. These were in turn converted into the Linear programming function. To faci1itate the data input process a simple input facility was developed. To maximize the value of the results the report writer was developed to enable sensitivity studies to be performed. This work was later used as the foundation of the NewGex programme.

The Master's Thesis research focuses on analyzing the possibilities of using Direct Current distribution systems to distribute power to end users. Considering the shift in load types in the past few decades and also a growing demand of distributed generation, DC distribution can potentially offer higher efficiencies and cost savings to utilities. The incorporation of DC distribution offers the opportunity to eliminate multiple conversion stages for devices which are powered using DC electricity. The integration of power sources such as photovoltaics and fuel cells, which produce DC power, offer further incentives to consider the use of DC systems. Using DC systems can help eliminate the conversion losses associated with rectifiers and inverters which would be part of the infrastructure if AC distribution was used. In the literature, the study of DC distribution has been limited to customized systems. The objective of this research is to analyze DC distribution when applied to systems based on standard IEEE test feeder systems. The IEEE 13 node test feeder and the IEEE 37 node test feeder will be used as the basis for the analysis. Issues such as associated costs, protection and integration of appliances will also be addressed.

Practically all everyday life tasks from economic transactions to entertainment depend on the availability of electricity. Some customers have come to expect a higher level of power quality and availability from their electric utility. Federal and state standards are now mandated for power service quality and utilities may be penalized if the number of interruptions exceeds the mandated standards. In order to meet the requirement for safety, reliability and quality of supply in distribution system, adaptive relaying and optimal network reconfiguration are proposed. By optimizing the system to be better prepared to handle a fault, the end result will be that in the event of a fault, the minimum number of customers will be affected. Thus reliability will increase. The main function of power system protection is to detect and remove the faulted parts as fast and as selectively as possible. The problem of coordinating protective relays in electric power systems consists of selecting suitable settings such that their fundamental protective function is met under the requirements of sensitivity, selectivity, reliability, and speed. In the proposed adaptive relaying approach, weather data will be incorporated as follows. By using real-time weather information, the potential area that might be affected by the severe weather will be determined. An algorithm is proposed for adaptive optimal relay setting (relays will optimally react to a potential fault). Different types of relays (and relay functions) and fuses will be considered in this optimization problem as well as their coordination with others. The proposed optimization method is based on mixed integer programming that will provide the optimal relay settings including pickup current, time dial setting, and different relay functions and so on. The main function of optimal network reconfiguration is to maximize the power supply using existing breakers and switches in the system. The ability to quickly and flexibly reconfigure the power system of an interconnected network of feeders is a key component of Smart Grid. New technologies are being injected into the distribution systems such as advanced metering, distribution automation, distribution generation and distributed storage. With these new technologies, the optimal network reconfiguration becomes more complicated. The proposed algorithms will be implemented and demonstrated on a realistic test system. The end result will be improved reliability. The improvements will be quantified with reliability indexes such as SAIDI.

M. Tech. Electrical Engineering. / This dissertation presents an effective method to determine current/voltage harmonic emission levels caused by various devices in the network. The method is implemented based on the existing power monitoring devices installed in power generation plants. The Digital Fault Recorders (DFRs) are used in this work as the monitoring devices. Due to the advancement of data processing and communication capabilities of such devices, a large amount of information generated by DFRs is concentrated in the utilitys head office. This data is archived for permanent storage and analysis. The presented work aims to assist the power utilities in harmonic invigilation problems based on DFRs.

Do domestic variables matter in a context of bilateral cooperation? What factors positively influence the decision-making process in the case of a policy harmonization between two countries? By studying both countries' institutional differences and governmental and non-governmental actors' preferences in the energy sector, this research analyzes the bilateral cooperation between Canada and the United States regarding the creation of the Electric Reliability Organization. Although domestic institutional constraints are important to consider, I argue that both physical and economic market integration and the use of a non-governmental organization by central governments have facilitated the success of the cooperation process. Those factors have favored the convergence of decisional actors' preferences and the inclusion of the majority of actors from all sectors of the industry into the process. The analysis uses a sequential model implying the division decision-making process over foreign policy into specific stages to show the importance of domestic variables. / Key words: Governmental cooperation, bilateral relations, actors' preferences, institution, energy sector, electricity, transmission network, reliability standards, market integration, restructured electricity market.

[Truncated introduction] A major contribution of this thesis is the observation that the N port impedance parameters for the distribution planes can be modelled as simple LC series elements in the frequency range over which the interesting interactions between the loading elements and the planes occur. Loosely speaking, the C represents the inter-plane capacitance and the L is associated with a first order frequency trend of the transfer and input impedances associated with the planes. In the literature, values for L have been obtained for power ground plane structures using curve fitting techniques [38]. In this thesis, formulae are developed for L based on the modal summation expression. As for the impedance case, the approach developed in the thesis that removes the singular behaviour, results in computational efficient expressions. Preliminary results on the simple LC model were presented by the author in [42, 43] The results reported in the thesis extend this work in the light of the new impedance model proposed. The simple LC characterisation enables the development of new low frequency expression for the input and transfer impedance for ports on planes loaded with many decoupling capacitors. The expressions are based on a one off frequency independent decomposition of the inductance matrix associated with the placement of the capacitors. The eigen-mode decomposition eliminates the need for matrix inversion at each frequency point and leads to an efficient computational procedure for calculating the impedance of loaded planes. Furthermore, the interaction between the capacitors and planes is clearly seen in the analytical expressions. This has led to new insights regarding the interaction of multiple capacitors with supply planes in terms of location, resonance mechanisms, pole locations and damping. These insights are beneficial to the understanding and optimisation of printed circuit board power distribution systems.

Ce travail est lié au système de protection des réseaux de distribution. Les réseaux radiaux dedistribution peuvent être protégés simplement par une protection placée en tête du départ. Maisl'exploitation future des réseaux de distribution, qui se transforment en réseaux intelligents,flexibles et adaptatifs, va sûrement nécessiter une protégeabilité plus complexe. Parconséquent, un nouveau plan de protection pourrait être nécessaire afin d’augmenter la fiabilitédu réseau de distribution et le taux de productions décentralisées. Il pourrait inclure plusieursprotections déployées sur un départ. Le but principal de ce travail est d'étudier comment lesprotections pourraient agir (sur quel genre de grandeurs les protections reposeront, quellecoordination faut-il choisir) et d'analyser les limites de ces nouvelles protections. En déployantplusieurs protections qui divisent le départ en des zones plus petites, le plan de protectionproposé, reposant sur une formulation modifié et optimisée, proche de celle des protections dedistance classiques, déconnectera ainsi moins de consommateurs et de producteurs lors del’apparition de défauts. Cela devrait réduire le temps de coupures brèves et de diminuerl'énergie non fournie. Ce manuscrit présente une solution pour les réseaux HTA radiaux faceaux défauts monophasés. / This work is related to the protection system of distribution networks. Radial MV distributiongrids can be protected by a single protection relay located at the beginning of the feeder. Butthe future operation mode of distribution grids turning into Smart Grids should impose morecomplex operations. Therefore a more advanced protection scheme could be needed, in orderto improve the reliability of the distribution network and to enhance the DG interconnection. Itcould include several protection relays in series on a same MV feeder. The main purpose of thiswork is to investigate how the protection relays could work (on which measurements should theprotection decisions be based, how to coordinate the relays without communication) andanalyze the limits of such new protection schemes. Since the goal is to insert severalprotections that divide the grid into smaller sections, the proposed protection system, based onan adapted and optimized formula, inspired by distance relays algorithm, would thereforedisconnect fewer loads and producers when faults occur in the MV network. This should reducethe clearing operation time and Energy Not Supplied criteria. This paper presents a solution fora radial MV grid facing single-phased faults.

No description available.

Thesis. 1978. Ph.D.--Massachusetts Institute of Technology. Dept. of Electrical Engineering and Computer Science. / MICROFICHE COPY AVAILABLE IN ARCHIVES AND ENGINEERING. / Bibliography: leaves 248-250. / Ph.D.