No description available.

Metallic films are important in various applications, such as electric devices where it can act as contacts. In electrical devices, the substrate typically consists of silicon dioxide (SiO2) which is a temperature-sensitive substrate. Therefore, plasma enhanced chemical vapor deposition (PECVD) are better suited than thermally activated chemical vapor deposition (CVD). Depositing metallic films with PECVD demands co-reactants that act as reducing agents. However, these are not well-studied and do not always have the power enough to perform the reduction reaction for metals. Recently it has been concluded that electrons can act as reducing agents in the deposition of first row transition metallic films in a PECVD process. By supplying a positive bias to the substrate, the electrons got attracted to the surface of the substrate, which facilitated metal growth. The study concluded that metal growth only occurred at conductive -and semiconductive substrates and that the substrate bias and plasma power affected the metal growth. The process is however not well understood, which causes a knowledge gap, signifying that studies of the surface chemistry are needed. Here a new modified analytical method to study the surface chemistry in the newly developed process mentioned above is presented. The analytical method consists of an electrically modified quartz crystal microbalance (QCM) with gold electrodes as a conductive substrate. This allows the electron current to run through the QCM during the measurement. By supplying a DC-voltage to the front electrode it gets readily biased (negative and positive) and by placing a capacitor in the circuit, it connects the AC-circuit (oscillator circuit) and the DC-circuit (DC-voltage bias circuit). At the same time, it blocks the DC-current from going back to the oscillator but allows the high-frequency signal to pass from the QCM. The results in this thesis concluded that the QCM can be electrically modified to allow an electron flux to the QCM while using it as a substrate when electrons are used as reducing agents. Scanning electron microscopy (SEM) of a QCM crystal revealed that a 2 µm film had been deposited while SEM coupled with energy dispersive X-ray spectroscopy (EDS) showed that the film indeed contained iron. Further analysis was made by high-resolution X-ray photoelectron spectroscopy (HR-XPS) to find the elemental composition of the film, which revealed that the thin film contained 41 at.% iron. In addition, this study investigated if the QCM could be used to study CVD processes where electrons were used as reducing agents. The results indeed revealed that it is possible to study the surface chemistry where electrons are used as reducing agents with the electrically modified QCM to gain knowledge concerning film deposition. Initial results of the QCM showed that film growth could be studied when varying the plasma power between 5 W to 15 W and the QCM bias between -40 V to +40 V. The method generated easily accessible data concerning the process where electrons are used as reducing agents, which gained insight to the method that never has been disclosed before.

Copper chlorophyllin (CuChl) is an antioxidant from renewable sources, which has shown as a potential active ingredient in agricultural crop sprays. The major objectives of this thesis are to understand the colloidal and interfacial behaviors of CuChl, and to develop strategies for improving its effectiveness in field applications. In this project, the following three areas are examined and analyzed. In practice, CuChl-based formulations are sprayed directly onto a plant’s foliage. As such, there is a need to understand how CuChl interacts with relevant plant surfaces. To this end, quartz crystal microbalance with dissipation (QCM-D) was used to quantify the adsorption of CuChl aqueous solutions onto four model surfaces: polystyrene, cellulose, pullulan, and silica. The results showed that cellulose adsorbed the highest amount of CuChl, followed by polystyrene and pullulan. In addition, the results also showed that the surfactants, SDS or DTAB, could alter the binding of CuChl to cellulose when used in concentrations above the critical micelle concentration. CuChl is composed of water-soluble and dispersed components, therefore it is not intrinsically rainfast, which limits its field application. To immobilize CuChl on leaves, a polymer combination of CMC (carboxymethyl cellulose) and PAE (polyamidoamine-epichlorohydrin) was designed for use as a spray adjuvant. The release behaviors of CuChl from dried spray deposits were investigated using varied polymer compositions and concentrations and compared with those of a water-soluble dye, brilliant sulfaflavine (BSF). The results indicated that a small amount of CuChl was immediately released upon exposure to water whereas BSF’s release behavior was dependent on the square root of time. The unusual behavior of CuChl was attributed to the presence of particles in the solution. These nanoparticles were coated with CMC:PAE complex, with the result of being immobilized on parafilm. Suspoemulsion is the most complex agricultural formulation that is composed of both dispersed particles and emulsion droplets. The objective of this work is to understand the relationship between the solution properties of suspoemulsions and the resulting dried deposits on hydrophobic surfaces. The results showed that the distribution of polychlorinated Cu (II) phthalocyanine (PG7) particles in dried deposits was related to the extent to which PG7 particles were adsorbed on or entrained in oil droplets. The PG7 particles that mainly ended up in the center (dome) area after drying were bound to the oil/water interface in the suspoemulsion, whereas individually dispersed particles ended up in the annulus. / Thesis / Doctor of Philosophy (PhD) / Agricultural formulations have been developed and widely applied to crops in an effort to maximize yields to keep up with the food demands of the world’s ever-growing population. However, there are still many challenges associated with the application of these formulations, such as huge losses due to spray drift, wash-off, and degradation during spraying. These issues can reduce the formulation’s overall efficacy and pose serious risks to the environment and human health. The primary objective of this thesis is to explore the agricultural application of a new environmentally-friendly active ingredient, copper chlorophyllin (CuChl). To this end, this work begins by determining CuChl’s colloidal and adsorption behaviors, with a particular focus on its binding tendencies for relevant plant surfaces. Next, a polymer combination was designed as a spray adjuvant to enhance CuChl’s rainfastness performance and CuChl’s release from dried deposits was characterized. Finally, the distribution of dispersed particles in dried suspoemulsion deposits was determined.

Developing methods to detect, adsorb, and decompose chemical warfare agents (CWAs) is of critical importance to protecting military and civilian populations alike. The sorption of dimethyl methylphosphonate (DMMP), a CWA simulant, into trisilanolphenyl-POSS (TPP) films has previously been characterized with reflection absorption infrared spectroscopy, x-ray photoelectron spectroscopy, and uptake coefficient determinations [1]. In our study, the quartz crystal microbalance (QCM) is used to study the sorption phenomena of DMMP into highly ordered Langmuir-Blodgett (LB) films of TPP. In a saturated environment, DMMP sorbs into the TPP films, binding to TPP in a 1:1 molar ratio. Although previous work indicated these DMMP-saturated films were stable for several weeks, DMMP is found to slowly desorb from the TPP films at room temperature and pressure. Upon application of vacuum to the DMMP-saturated films, DMMP follows first-order desorption kinetics and readily desorbs from the film, returning the TPP film to its original state. [1] Ferguson-McPherson, M.; Low, E.; Esker, A.; Morris, J. J. Phys. Chem. B. 2005, 109, 18914. / Master of Science

Plant cell wall polysaccharides are abundant natural polymers making them potential sources for sustainable and biodegradable materials. Interfacial behavior, including adsorption and enzymatic degradation, of several plant cell wall polysaccharides and their derivatives were studied with a quartz crystal microbalance with dissipation monitoring (QCM-D), surface plasmon resonance (SPR) and atomic force microscopy (AFM). Xyloglucan adsorption isotherms were obtained to probe how cellulose-hemicellulose interactions were affected by the type of cellulose substrate and molar mass of xyloglucan. Xyloglucan as small as a heptasaccharide still adsorbed irreversibly onto cellulose. Carboxymethyl cellulose (CMC) adsorption onto cellulose and viscoelastic properties and water contents of the adsorbed CMC layers were obtained from a combination of QCM-D and SPR data. The CMC samples formed hydrated and viscoelastic layers compared to the relatively rigid xyloglucan layer. Pectin model surfaces were prepared by pectin adsorption from citric phosphate buffer onto gold substrates. These pectin model surfaces were used for subsequent interaction studies with xyloglucan and enzymatic degradation behavior. There is a strong correlation between the degree of esterification (DE) and film resistance to degradation with the high DE being the most susceptible to degradation. The adsorption of two mixed linkage glucans (MLG), barley and lichen MLG, onto regenerated cellulose (RC) surfaces in the absence and presence of other matrix polysaccharides was studied. Viscoelastic properties of the resulting layer were compared as a function of the proprotion of '-(1''3) linkages with lichen MLG forming softer gel-like layers on RC. The lichen MLG layers were further used for enzymatic degradation studies with respect to enzyme concentration, temperature, pH and ionic strength. These studies show that polymer adsorption is a promising strategy to modify material surfaces and provides fundamental understanding of interactions and biodegradation of cell wall polysaccharides at solid/liquid interfaces. / Ph. D.

Elevated levels of lipids and LDL-cholesterol in the blood are significant risk factors associated with developing cardiovascular diseases (CVDs). A potential strategy to combat these risk factors is decreasing lipid absorption by modulating the digestibility of lipids in the human intestinal tract. Since bile salts (BS) play key roles during this process, lipid digestion could be controlled ultimately by limiting the access of BS to the lipid surface. Cellulose ethers (CEs), surface-active dietary fibers and common food additives, might be promising ingredients to control lipid digestion either by creating surface layers around lipid droplets that hinder adsorption of BS, or by sequestering BS in the aqueous phase. However, the precise mechanisms behind these interactions remain unclear. Surface analysis techniques were used to better understand the mechanisms by which CEs with diverse molecular structure and charge (commercial and novel hydroxypropyl-cellulose (HPC)) interact with BS at the solid surface and in the aqueous phase. The potential of CE-stabilized emulsions to influence lipid digestion was also investigated in vitro. Both CEs show potential in modulating lipid digestion; the potential of the commercial HPC to interfere with lipid digestion may be more related to its ability to sequester BS in solution and form mixed HPC-BS complexes that are not easily removed from the surface, whereas the novel HPC seems more effective at creating strong surface layers that resist displacement by BS. These findings can be exploited in developing strategies to design novel food matrices with improved functional properties to optimize lipid digestion and absorption. / MSLFS / Diseases of the heart and circulation are the number one cause of death in the United States (US) and it is predicted that at least 45% of the US population (131.2 million) will have some form of these diseases by 2035. Consumption of reduced-fat foods is one strategy to combat CVDs, but fats contribute to various sensory and nutritional properties of foods. Another strategy is to develop foods that incorporate dietary fibers which could interfere with the digestion of fat. However, the mechanism behind the ability of dietary fiber to interfere with fat digestion remains unclear and depends on the fiber type. One of our objectives was to look at the main interactions between a type of dietary fiber, cellulose derivatives (which are ingredients used in the food industry), and two types of bile salts, (BSs) which are important intestinal components present during fat digestion, at a surface representing a fat droplet and in the aqueous phase. Another objective was to look at the digestibility of cellulose derivative systems, compared to another food ingredient (Tween 20). We found that the different BSs played different roles at the surface and interacted differently with the cellulose derivatives. We also found that both cellulose derivatives showed potential in interfering with lipid digestion. This allows a better understanding of how cellulose derivative systems are affected by digestion and could allow us to design new foods with natural products from plants to improve wellness in the US.

Interfaces are ubiquitous in our daily life. A good understanding of the interfacial properties between different materials, or a single material in different physical states is of critical importance for us to explore the current world and bring benefits to mankind. In this work, interfacial behavior was investigated with the help of surface analysis techniques, such as quartz crystal microbalance with dissipation monitoring (QCM-D), surface plasmon resonance (SPR) and atomic force microscopy (AFM), in order to gain better understanding on biofuel conversion, gene/drug delivery, and chemical fixation of CO2. Biomimetic chelator-mediated Fenton (CMF) non-enzymatic degradations on cellulose and chitin thin films was studied by liquid-phase QCM-D and AFM. QCM-D is a powerful tool to monitor the kinetics of hydrolysis of regenerated cellulose and chitin model surfaces. Results from QCM-D and AFM showed that the majority of the biomass of the two model surfaces can be hydrolyzed by the CMF system. The initial degradation rates for both model surfaces by the CMF system are faster than that of the corresponding enzyme systems. The CMF system, which is a good non-enzymatic pretreatment agent for cellulose and chitin, may work on a wide variety of polysaccharide systems. Adsorption of cationic cellulose derivatives onto self-assembled monolayer (SAM) surfaces was investigated using liquid-phase SPR. Results from SPR showed that depending upon the cellulose derivative structure, irreversible adsorption ranging from a monolayer to ~1.6 layers of cellulose derivative were formed on the SAM-COOH surface based upon a charge neutralization mechanism. At low salt concentrations, the long-range electrostatic attraction between the cationic cellulose derivatives (6-PyrCA and 6-MeIMCA) and the SAM surfaces facilitates the formation of a 2-dimensional monolayer. While, for TMACE, the energy gained through the hydrophobic interaction between adjacent long polyelectrolyte branches may afford the electrostatic repulsion and chain entropy penalties, resulting in the formation of 3-dimensional adsorbed polyelectrolyte layers. Adsorption of 1,2-epoxybutane gas molecules onto/into VPI-100 metal–organic frameworks (MOFs) was studied by gas-phase QCM-D experiments. Results from QCM-D demonstrated that VPI-100 (Ni) MOFs have higher irreversible adsorption per unit cell (θ) and faster diffusion coefficients (D) than VPI-100 (Cu) MOFs. The presence of bound counter-balancing ions on the metallo-cyclam core was attributed as the cause of the higher θ and faster D through the Ni analogue, which suggests the MOF-epoxide interaction occurs at the metallo-cyclam. This study shed light upon tuning MOF structures for better CO2 sorption and epoxide activation to gain higher catalytic efficiency. Finally, in operando high energy X-ray diffraction (HEXRD) was used to monitor the phase transition of the NaxNi1/3Co1/3Mn1/3O2 cathode material during the sintering process. The first charge/discharge cycle of the NaxNi1/3Co1/3Mn1/3O2 cathode materials in different phases were also studied by in operando HEXRD. It was found that the intergrowth P2/O1/O3 cathode (NCM-Q cathode) can inhibit the irreversible P2–O2 phase transition and simultaneously improve the structural stability of the O3 and O1 phases during cycling. The NCM-Q cathode with triple-phase integration demonstrates highly reversible phase evolution during high voltage cycling, possibly leading to a highly reversible capacity and good cycle stability. / Doctor of Philosophy / Interfaces and surfaces are everywhere. Many critical processes, such as molecular recognition, catalysis, and charge transfer, take place at interfaces. The surfaces of plants and animals provide barriers from pathogens, prevent damage from mechanical impacts, detect external stimuli, etc. Inside the human body, nutrition and oxygen are adsorbed through interactions between substances and cell surfaces. Investigations of interfacial behaviors may help us understand our current world better and bring benefits to mankind. In this dissertation, the interface between bio-renewable natural polymers and biomimetic chelators, the interface between a self-assembled monolayer and cationic cellulose derivatives, and the interface between metal–organic frameworks (MOF) and 1,2-epoxybutane gas molecules, were studied with a quartz crystal microbalance with dissipation monitoring (QCM-D), surface plasmon resonance (SPR) and atomic force microscopy (AFM), to gain insights into biofuel conversion, gene/drug delivery and chemical fixation of CO2, respectively. Additionally, thermally and electrochemically induced phase transitions in sodium-ion battery (SIB) cathode materials were probed via in operando high energy X-ray diffraction (HEXRD). Biomimetic chelator-mediated Fenton (CMF) non-enzymatic degradations of cellulose and chitin thin films were studied by liquid-phase QCM-D and AFM. It was found that the majority of the biomass of the two model surfaces can be degraded by the CMF system. Adsorption of cationic cellulose derivatives onto self-assembled monolayer (SAM) surfaces was investigated using liquid-phase SPR. It was found that both the absorbed layer conformation and the absorbed amount depend upon the interplay between long-range electrostatic interactions and short-range interactions. Adsorption of 1,2-epoxybutane gas molecules onto/into VPI-100 MOFs was studied by gas-phase QCM-D experiments. Data from QCM-D revealed the irreversible gas molecule absorption onto/into MOFs and shed light upon tuning MOF structures for better CO2 sorption and epoxide activation to gain higher catalytic efficiency. Finally, the in operando high energy X-ray diffraction (HEXRD) was used to probe thermally and electrochemically induced phase transitions in sodium-ion battery (SIB) cathode materials. It was found that the NCM-Q cathode with triple-phase integration demonstrates highly reversible phase evolution during high voltage cycling, possibly leading to a highly reversible capacity and good cycle stability.

The advancements of chemists, engineers, and material scientists has yielded an enormous and diverse library of high-performance materials with varying chemical and physical properties that can be used in a wide array of applications. A molecular-level understanding of the nature of gas–surface interactions is critical to the development of next generation materials for applications such as gas storage and separation, chemical sensing, catalysis, energy conversion, and protective coatings. Quartz crystal microbalance (QCM) and in situ infrared (IR) spectroscopic techniques were employed to probe how topological features of a material as well as structural differences of the analytes affect gas sorption. Detailed studies of the interactions of three categories of molecules: aromatic hydrocarbons, triatomic ambient gases, and chemical warfare agents, with metal-organic frameworks (MOFs) and polyurethane coatings were conducted to build structure–property relationships for the nature and energetics of gas sorption within each material. Differences in the molecular structure of the guest compounds were found to greatly influence how, and to what extent each molecule interacts with the MOF or polyurethane film. Specifically, IR studies revealed that transport of aromatic compounds within the zirconium-based MOF, UiO-66 was limited by steric restrictions as molecules passed through small triangular apertures within the pore environment of the MOF. In contrast, the smaller triatomic molecules, CO2, SO2, and NO2, were able to pass freely through the MOF apertures and instead reversibly adsorbed inside the MOF cavities. Specifically, SO2 and NO2 were observed to preferentially bind to undercoordinated zirconium sites located on the MOF nodes. In addition, uptake of CO2, SO2, and NO2 was also aided by dispersion forces within the confined pore environments and by hydrogen bond formation with μ3 OH groups of the MOFs. Dimethyl chlorophosphate (DMCP), a nerve agent simulant that contains several electronegative moieties, was also found to strongly adsorb to undercoordinated zirconium; however, unlike in the aromatic and triatomic molecule systems, DMCP remained permanently bound to the MOFs, even at high temperatures. Finally, QCM studies of mustard gas simulant uptake into polyurethane films of varying hard:soft segment compositions revealed that dipole-dipole and dipole-induced dipole interactions were responsible for favorable absorption conditions. Furthermore, the ratio of hard and soft segment components of the polyurethane had a minor impact on simulant adsorption. Higher hard-segment content resulted in a more crystalline film that reduced simulant uptake, whereas the rubbery, high soft segment polyurethane allowed for greater vapor absorption. Ultimately, molecular-level insight into how the chemical identity of a guest molecule impacts the mechanism and energetics of vapor sorption into both MOFs and polymeric films can be extended to other relevant systems and may help identify how specific characteristics of each material, such as size, shape, and chemical functionality impact their potential use in targeted applications. / Doctor of Philosophy / The nature in which specific gases interact with materials will largely dictate how the material can be utilized. By understanding where and how strongly gas molecules interact with a material, scientists and engineers can rationally design new and improved systems for targeted applications. In the research described in this thesis, we examined how the chemical structure of three different groups of compounds, which have relevance in many industrial, environmental, and defense-related applications, affected the type and strength of interaction between the gas and material of interest. From these studies, we have identified how key properties and features within the examined materials such as size, shape, and chemical composition, lead to significant differences in how vapor molecules interacted with the materials. For example, benzene, toluene, and xylene, which are incredibly important chemicals in industry, were found to be restricted by narrow passageways as they moved through materials with small pores. In contrast, small gases present in the environment from combustion exhaust such as CO₂, SO₂, and NO₂ were able to freely traverse through the passageways, and instead weakly interacted with specific chemical groups inside the cavities of the material. On the same material however, a third class of compounds, organophosphorus-containing chemical warfare agent mimics, irreversibly reacted with chemical groups of the surface, and remained bound even after exposure to high temperatures. Ultimately, the work presented in this thesis is aimed at providing key fundamental insights about specific classes of materials on how, and how strongly they interact with targeted hazardous vapors, which can be utilized by synthetic chemists to design next generation materials.

The focus of this dissertation research involves surface charge manipulation of functionalized monolayers. Application of potential to acid or base terminated organic films immobilized on electrodes results in the ionization of the terminal groups. The ionization of these groups using applied potential provides conditions favorable the control of polyelectrolyte deposition to the monolayer surface. Research is presented that asserts that the interfacial pH of acid or base terminated monolayers responds to applied potential as a result of the accumulation of phosphate counterions to the monolayer-solution interface. Results obtained from applied potential modulation of surface charge endeavors strongly suggest that manipulation of terminal group ionization with applied potential “turns on“ or “turns off“ the charge of the monolayer. Switching on the surface charge of functionalized monolayers using applied potential yields conditions that make it possible for the promotion or inhibition of electrostatic attachment of polyelectrolyte to the monolayer surface. Electrostatic interactions between immobilized polyelectrolytes and redox probes result in changes in electron transfer that can be monitored with electrochemical impedance measurements. Impedance measurements provide a qualitative assessment of the degree of potential-driven polyelectrolyte self assembly. The electrostatic interactions between the redox probe in solution and the terminal region of monolayers directly affects the extent of charge-transfer between the electrode and the redox probe in solution. For this reason, impedance measurements are able to provide an indication of whether or not potential drives to electrostatic deposition to the terminal region of a functionalized monolayer. Unlike impedance measurements, quartz crystal microbalance measurements provide quantitative mass assessments that confirm polyelectrolyte deposition of inhibition under the direction of applied potential. Application of appropriate potentials is shown to induce variations in the electrostatic interactions between redox probes in solution and terminal groups of monolayers. Variations in the electrostatic interactions between the modified electrode and the redox probe modulate electron transfer that produces varying current. Since scanning electrochemical microscopy (SECM) relies on modulation of feedback current underneath a ten-micrometer platinum tip, SECM provides a means for monitoring of potential-driven surface charge modulation. Experiments presented in this dissertation will show that in addition to monitoring the effect of applied potential on the charge of ionizable surface groups, SECM can also be used to selectively deposit a polyelectrolyte to the surface of a carboxylic acid terminated monolayer. The SECM tip was rastered over the surface of a functionalized monolayer in the form of a simple pattern while the electrode was immersed in a dilute polyelectrolyte solution. As the SECM tip was moved and potential stepped more positive than the PZC, ionization was confined ionization to one spot encouraging localized ionic self assembly. / Ph. D.

Orientador: David Mendez Soares / Tese (doutorado) - Universidade Estadual de Campinas, Instituto de Física Gleb Wataghin / Made available in DSpace on 2018-08-17T17:51:55Z (GMT). No. of bitstreams: 1 Gomide_AndrezaBarbosa_D.pdf: 5782130 bytes, checksum: 73ea74eba4132f68eced1394071826de (MD5) Previous issue date: 2011 / Resumo: Frente à complexidade estrutural e funcional das membranas biológicas, a construção de membranas modelo sobre suporte sólido surge como uma resposta para o estudo daquelas. Para acessar as propriedades estruturais e funcionais de uma membrana biológica é fundamental que a membrana modelo seja capaz de refletir a interface membrana/ambiente aquoso. Portanto, foi feito um estudo da água frente à superfície sólida e verificou-se que a água frente a superfícies pode apresentar estrutura e propriedades físicas como densidade, viscosidade, constante dielétrica, etc. diferentes da águas da massa líquida (bulk water). Também investigamos a formação de filmes de fosfolipídios sobre o eletrodo de ouro a partir de soluções de lipossomos. A microbalança de cristal de quartzo (QCM) mostrou os processos de adsorção de lipossomos à superfície do eletrodo de ouro, de ruptura e formação de filmes. Usando a técnica de filmes de Langmuir, determinamos a densidade de fosfolipídios em uma membrana modelo e comparamos com os resultados gravimétricos obtidos com a QCM. Com a técnica de miscroscopia de força atômica (AFM) usando medidas de força vs. distância, detectamos a espessura do filme de DMPC (6 nm). Além disso, mostramos que na presença de uma solução 0,5 M de H2SO4 o filme formado apresenta uma rugosidade na superfície que muda conforme o potencial aplicado ao eletrodo / Abstract: Faced with structural and functional complexity of biological membranes, the construction of model membranes on solid support appears as a response to the study of those. To access the structural and functional properties of a biological membrane, it is crucial that the membrane model is able to reflect the interface membrane/aqueous environment. Therefore, a study was made of water contacting a solid surface. It was found that water close to surfaces can have structure and physical properties (as density, viscosity, dielectric constant, etc..) different from bulk water. We also investigated the formation of phospholipid films on the gold electrode from solutions of liposomes. The quartz crystal microbalance (QCM) showed the adsorption of liposomes to the surface of gold electrode, breakdown and formation of a film. Using the technique of Langmuir we determined the density of phospholipids in a membrane model and compared with the gravimetric results obtained with the QCM. With the atomic force microscope (AFM) using the force vs. distance measurement we detected a 6 nm thick DMPC film on the electrode. Furthermore, we showed that in the presence of a 0.5 M solution of H2SO4 the film formed on the surface has a roughness that changes with the applied potential to the electrode / Doutorado / Físico-Química / Doutora em Ciências