L'objectif de cette thèse CIFRE est de contribuer à la communication véhiculaire autonome et au développement de la mobilité urbaine. Les travaux sont basés sur les limitations et défis de la communication par radio pour les applications de sécurité et envisagent de déployer le système d'éclairage des véhicules en tant que solution de communication de soutien pour le platooning d'IVC-activées par VC Véhicules autonomes. L'objectif principale de cette recherche doctorale consiste à intégrer le système VLC dans l'architecture existante de C-ITS en développant un prototype VLC, ainsi que des algorithmes de transfert suffisants permettant VLC, RF et des solutions basées sur la perception afin d'assurer les exigences de sécurité maximales et l'échange continu d'informations entre les véhicules. La faisabilité et l'efficacité de la mise en oeuvre du système et des algorithmes de transfert ont fait l'objet de recherches approfondies sur six chapitres, destinés à faciliter une progression logique des matériaux et permettre un accès relativement facile. En plus de l'amélioration de la capacité routière en utilisant les systèmes de conduite autonome à la base de convoi. Les simulations réalisées ainsi que les résultats expérimentaux ont montré que l'intégration de VLC avec les solutions existantes RF a un avantage certain dans la qualité du canal de communication et les exigences de sécurité d'un système de platooning quand un algorithme approprié est utilisé. / This thesis effort contributes to the autonomous vehicular communication and urban mobility improvements. The work addresses the main radio-based V2V communication limitations and challenges for ITS hard-safety applications and intends to deploy the vehicular lighting system as a supportive communication solution for platooning of IVC-enabled autonomous vehicles. The ultimate objectives of this Ph.D research are to integrate the VLC system within the existing C-ITS architecture by developing a VLC prototype, together with sufficient, hand-over algorithms enabling VLC, RF, and perception-based solutions in order to ensure the maximum safety requirements and the continuous information exchange between vehicles. The feasibility and efficiency of the VLC-RF system implementation and hand-over algorithms were subjects to deep investigations over six self-contained chapters meant to facilitate a logical progression of materials and to enable a relatively easy access. In addition to the improvement in road capacity by utilizing the convoy-based autonomous driving systems. The carried out simulations followed-up by experimental results proved that the integration of VLC with the existed RF solutions lead to a definite benefit in the communication channel quality and safety requirements of a platooning system when a proper hand-over algorithm is utilized.

In this thesis we address the problem of providing end-to-end quality of service (QoS) to real-time and data connections in a third generation (3G) cellular network based on the Universal Mobile Telecommunication System (UMTS) standard. Data applications usually use TCP (Transmission Control Protocol) and the QoS is a minimum guaranteed mean throughput. For this one first needs to compute the throughput of a TCP connection sending its traffic through the UMTS network (possibly also through the wired part of the Internet). Thus we obtain closed form expressions for a TCP throughput in a UMTS environment. For downloading data at a mobile terminal, the packets of each TCP connection are stored in separate queues at the base station (node B). These are fragmented into Protocol Data Units (PDU). The link layer uses ARQ (Automatic Repeat Request). Thus there can be significant random transmission/queueing delays of TCP packets at the node B. On the other hand the link may not be fully utilized due to the delays of the TCP packets in the rest of the network. In such a scenario the existing models of TCP may not be sufficient. Thus we provide new approximate models for TCP and also obtain new closed form expressions of mean window size. Using these we obtain the throughput of a TCP connection for the scenario where the queueing delays are non-negligible compared to the overall Round Trip Time (RTT) and also the link utilization is less than one. Our approximate models can be useful not only in the UMTS context but also else where. In the second half of the thesis, we use these approximate models of TCP to provide minimum mean throughput to data connections in UMTS. We also consider real-time applications such as voice and video. These can tolerate a little packet loss (~1%) but require an upper Bound on the delay and delay jitter (≤ 150 ms). Thus if the network provides a constant bandwidth and the received SINR is above a specified threshold ( with a certain probability), QoS for the real-time traffic will be satisfied. The 3G cellular systems are interference limited. Thus wise allocation of power is critical in these systems. Hence we consider the problem of providing end-to-end QoS to different users along with the minimization of the downlink power allocation.

This thesis describes the work process two (WP2) of a project led by the traffic administration in Stockholm to achieve the passengers' thermal comfort in traffic buses.  The purpose of this thesis is to design and implement a measurement system comprised in eight measurement position in a bus. Each position is able to transmit data using a wireless communication protocol, with a central unit collecting all the transmitted data taking into consideration the accuracy of the measurements and filtering out the incorrect data. In order to accomplish this, a literature study is conducted investigating different measurement methods for different parameters, different communication protocols were analysed as well to determine an appropriate communication protocol suitable for climate measurement in a bus environment with passengers present on board.  The output of the HVAC system is also required to help the traffic administration demonstrate the results of adjusting the temperature in the bus to reach the thermal comfort and how it led to saving energy. The system incorporates ZigBee , ESP32 microcontroller in the sender positions and a Raspberry pi operating as a central unit to collect data and store it in a file system providing an accurate data that will help the traffic administration achieve their goals. Unfortunately, there were some diffculties accessing CAN system data to provide the output of the HVAC system. / Detta examensarbete beskriver arbetsprocess två i ett projekt som leds av trafikförvaltningen i Stockholm för att uppnå termiska komfort för passagerare i busstrafik.  Syftet med detta examensarbete är att utforma och implementera ett mätsystem bestående av åtta positioner i en buss. Varje position kan överföra data med hjälp av ett trådlöst kommunikationsprotokoll, en central enhet samlar in all data med hänsyn till mätningens noggrannhet och filtrering av felaktig data. För att uppnå detta utfördes en litteraturstudie för att undersöka mätningsmetoder för de olika parametrar. Olika kommunikationsprotokoll undersöktes för att bestämma en lämplig kommunikationsprotkoll för ett mätsystem som mäter klimat i bussar med passagerare ombord. Uteffekten av HVAC-systemet krävs också för att hjälpa trafikförvaltningen att bestämma fördelarna med att justera temperaturen i bussen för att nå den termiska komforten och hur den ledde till att spara energi. Systemet inkorporerar kommunikaitonsprotokollet ZigBee, ESP32-mikrokontroller i avsändarpositionerna och en Raspberry pi som fungerade som en central enhet för att samla in data och lagra det i ett filsystem med korrekta data som hjälper trafikförvaltningen att uppnå sina mål. Svårigheter uppstod med att få tillgång till CAN-system data för uteffekten av HVAC-systemet.

Le déploiement d'une infrastructure de supervision permet une gestion plus intelligente des réseaux de distribution d'électricité comparé à un renforcement traditionnel pour répondre aux nouveaux enjeux de la maitrise de l'énergie (Consommations, EnR, VE, ...). Pour acheminer les données, les Courants Porteurs en Ligne (CPL) possèdent un atout majeur. En effet, cette technologie permet de superposer un signal de plus haute fréquence au signal électrique 50/60 Hz. Toutefois, le support de transmission est difficile et non maîtrisable. Ces travaux de recherche ont pour objectif d'apporter une contribution à cette problématique par l'élaboration d'une plateforme de simulation des réseaux pour des fréquences allant jusqu'à 1 MHz dans un but de transmission de données. Des éléments clés des réseaux sont traités de façon séparés puis assemblés pour estimer les performances des CPL « Outdoor » actuels. La variation du comportement des réseaux en fonction du temps et de la fréquence, en particulier des perturbations en tête d'installation clients sur 24h est étudiée. Les transformateurs entre les réseaux HTA et BT sont modélisés sous la forme d'un « modèle à constantes localisées » et d'un « modèle boite noire ». Les deux modèles sont appliqués sur un transformateur H61 100 kVA. Par la suite, une modélisation des câbles de distribution est proposée sous forme d'un « modèle cascadé ». Celle-ci est appliquée sur un câble souterrain BT. Chaque modèle est obtenu à l'aide de mesures d'impédances, et validé par des mesures de transmissions. Pour compléter, une étude préliminaire sur les communications radio mobile est réalisée pour la supervision des réseaux de distribution. / Establishing a supervisory infrastructure allows a better smart management than an expensive strengthening of distribution network to respond to new constraints at the energies control (Consumption, REN, EV ...). To transmit data, Power Line Communication (PLC) technologies present an advantage in this context. In fact, it enables a superposition of High Frequency (HF) signals on electrical signal 50/60 Hz. However, electric networks have not been developed to this application because of difficult propagation conditions. This research work makes a contribution to develop a simulation platform in objective to transmit data to 1 MHz. In first time, each network element is studied singly and in second time, together, to estimate "Outdoor PLC" transmission performance. The first element studied is the networks variation in function of frequency and time. Several 24h disturbance measurements on LV customers are presented. The second element is the transformers which established connection between Medium Voltage (MV) and Low Voltage (LV). The proposed modeling method is based on a "lumped model" and a "black box model". These models are applied to a 100 kVA H61 transformer most commonly used by French distribution system operator in rural and suburban networks. The third element is the power line used in MV and LV networks. The proposed modeling method is based on a "cascaded model" from the theory of transmission line. This model is applied to one power line used in LV underground network. Each model is obtained from various impedance measurements. To complete, an introductory study on mobile radio communication is performed to remote network distribution.