Highway drainage pipes utilize concrete reinforced with steel wire to help mitigate water, earth, and traffic loads. Drainage pipes reinforced with zinc electroplated steel fibers offer a lower steel alternative to traditional steel wire cage reinforcements. The objective of the thesis research was to determine the physical and electrochemical characteristics of zinc electroplated steel fiber corrosion propagation. Experimental programs include: Fracture analysis of zinc electroplated steel fibers embedded in dry-cast concrete pipes exposed to varying chloride concentrations; Visual analysis of zinc electroplated steel fibers embedded in concrete exposed to varying chloride concentrations; Electrochemical analysis of zinc electroplated steel fibers embedded in concrete exposed to varying chlorides; Chloride threshold determination for zinc electroplated steel fibers immersed in simulated pore solution. Between the four experimental programs the most significant conclusion is that oxygen, moisture, and chlorides past the chloride threshold must be present for corrosion to propagate significantly on the zinc electroplated steel fibers. / Includes bibliography. / Thesis (M.S.)--Florida Atlantic University, 2016. / FAU Electronic Theses and Dissertations Collection

The aim of this study was to investigate the diffusion of chloride ions into concrete samples that were exposed in scenarios that simulate the splash, tidal, atmospheric, and immersed portions of a marine structure. To study the atmospheric deposition, the project also investigated the relationship between chloride ion deposition on the wet candle and its accumulation into concrete samples. Results from the wet candle experiment indicated that between 2% and 45% of the chlorides deposited per square meter of exposed area could be found within the concrete samples. After 6 months, slag G1a blocks showed the most resistance to chloride penetration in the tidal and splash simulations. After 10 months of exposure, fly ash samples had the slowest rates of diffusion in the tidal simulation while the fly ash + silica fume samples and the slag samples measured similar rates of diffusion within the tidal zone. After 90 days of curing, cylinders composed of 20% fly ash & 8% silica fume measured the highest average resistivity values and were found to be less vulnerable to chloride ion penetration than the 20% fly ash and the 50% slag concrete through rapid migration tests. / by Victor Anthony Echevarria. / Thesis (M.S.C.S.)--Florida Atlantic University, 2012. / Includes bibliography. / Mode of access: World Wide Web. / System requirements: Adobe Reader.

The construction industry is increasingly turning to the use of environmentally friendly materials in order to meet the sustainable aspect required by modern infrastructures. Consequently, for the last two decades, the expansion of this concept, and the increasing global warming have raised concerns on the extensive use of Portland cement due to the high amount of carbon dioxide gas associated with its production. The development of geopolymer concretes offers promising signs for a change in the way of producing concrete. However, to seriously consider geopolymer binders as an alternative to ordinary Portland cement, the durability of this new material should be evaluated in any comparative analysis. The main purpose of this study was to evaluate the durability characteristics of low calcium fly ash-based geopolymer concretes subjected to the marine environment, compared to ordinary Portland cement concrete with similar exposure. To achieve this goal, 8 molar geopolymer, 14 molar geopolymer and ordinary Portland cement concrete mixes were prepared and tested for exposure in seawater. Compressive strengths in the range of 2900 to 8700 psi (20-60 MPa) were obtained. The corrosion resistance performance of steel-reinforced concrete beams, made of these mixes, was also studied, using an accelerated electrochemical method, with submergence in salt water. The test results indicated that the geopolymer concrete showed excellent resistance to chloride attack, with longer time to corrosion cracking, compared to ordinary Portland cement concrete. / by Jean-Baptiste Edouard. / Thesis (M.S.C.S.)--Florida Atlantic University, 2011. / Includes bibliography. / Electronic reproduction. Boca Raton, Fla., 2011. Mode of access: World Wide Web.

The durability of Reinforced Concrete (RC) structures in the Marine environment is causing serious concern in the structural infrastructure. Reinforced concrete structures, exposed to aggressive environments, are expected to last with little or no maintenance for long periods of time. However, one of the most serious environmental exposures that causes degradation is Chloride Diffusion, due to shrinkage, atmospheric corrosion, and tide-induced wet and dry conditions at the air-water interfaces of coastal structures. Therefore, chloride diffusivity, which correlates with the electrical resistivity, has a significant impact on the durability of concrete. Concrete chloride diffusivity has been experimented by multiple agencies and researchers on sound concrete, but there is a considerable need for investigation of the durability of cracked concrete in the marine environment. The two test methods carried out are presented: Standardized American Society for Testing and Materials (ASTM) C1202 for Rapid Chloride Permeability (RCP) and ASTM D257 for Surface Resistivity (SR), and Nordtest (NT) Build 492 for Rapid Chloride Migration (RCM) and Bulk Resistivity (BR) for both sound (uncracked) and cracked (micro and macro) concrete. The limitations of the ASTM method, due to measurements before the steady-state migration is reached, does not account for leakage in cracked concrete, and the heating of the specimen due to higher current that increase the conductivity are indicated. The Rapid Chloride Migration test provides for the non-steady state of diffusion. Again, Bulk Resistivity, in contradistinction to Surface Resistivity is more accurate for cracked concrete. The correlation betweeen RCM-BR are plotted. Chloride Permeability/Migration is an important parameter that governs the Durability of Concrete. The principal contribution is the highlighting of the inadequacy of the current widely used standard ASTM C1202 for diffusivity testing, and the need for revision with further investigation. / Includes bibliography. / Thesis (M.S.)--Florida Atlantic University, 2017. / FAU Electronic Theses and Dissertations Collection

In the Middle East region and many countries in the world, older reinforced concrete (RC) columns are deemed to be weak in seismic resistance because of their low amount of reinforcement, low grades of concrete, and large spacing between the transverse reinforcement. The capacity of older RC columns that are also slender is further reduced due to the secondary moments. Appropriate retrofit techniques can improve the capacity and behavior of concrete members. In this study, externally bonded Carbon Fiber Reinforced Polymer (CFRP) retrofit technique was implemented to improve the behavior of RC columns tested under constant axial load and cyclic lateral load. The study included physical testing of five half-scale slender RC columns, with shear span to depth ratio of 7. Three specimens represented columns in a 2-story, and two specimens represented columns in a 4-story building. All specimens had identical cross sections, reinforcement detail, and concrete strength. Two specimens were control, two specimens were retrofit with CFRP in the lateral direction, and one specimen retrofit in the longitudinal and lateral directions. A computer model was created to predict the lateral load-displacement relations. The experimental results show improvement in the retrofit specimens in strength, ductility, and energy dissipation. The effect of retrofitting technique applied to two full-scale prototype RC buildings, a 2-story and a 4-story building located in two cities in Iraq, Baghdad, and Erbil, was determined using SAP2000.

A large magnitude, long duration subduction earthquake is impending in the Pacific Northwest, which lies near the Cascadia Subduction Zone (CSZ). Great subduction zone earthquakes are the largest earthquakes in the world and are the sole source zones that can produce earthquakes greater than M8.5. Additionally, the increased duration of a CSZ earthquake may result in more structural damage than expected. Given such seismic hazard, the assessment of reinforced concrete substructures has become crucial in order to prioritize the bridges that may need to be retrofitted and to maintain the highway network operable after a major seismic event. Recent long duration subduction earthquakes occurred in Maule, Chile (Mw 8.8, 2010) and Tohoku, Japan (Mw 9.0, 2011) are a reminder of the importance of studying the effect of subduction ground motions on structural performance. For this purpose, the seismic performance of substandard circular reinforced concrete bridge columns was experimentally evaluated using shake table tests by comparing the column response from crustal and subduction ground motions. Three continuous reinforced columns and three lap-spliced columns were tested using records from 1989 Loma Prieta, 2010 Maule and 2011 Tohoku. The results of the large-scale experiments and numerical studies demonstrated that the increased duration of subduction ground motions affects the displacement capacity and can influence the failure mode of bridge columns. Furthermore, more damage was recorded under the subduction ground motions as compared to similar maximum deformations under the crustal ground motion. The larger number of plastic strain cycles imposed by subduction ground motions influence occurrence of reinforcement bar buckling at lower displacement compared to crustal ground motions. Moreover, based on the experimental and numerical results, subduction zone ground motion effects are considered to have a significant effect on the performance of bridge columns. Therefore, it is recommended to consider the effects of subduction zone earthquakes in the performance assessment of substandard bridges, or when choosing ground motions for nonlinear time-history analysis, especially in regions prone to subduction zone mega earthquakes. Finally, for substandard bridges not yet retrofitted or upgraded seismically, the following performance limit recommendation is proposed: for the damage state of collapse, which is related to the ODOT's Life Safety performance level, the maximum strain in the longitudinal reinforcement should be reduced from 0.09 (in./in.) to a value of 0.032 (in./in.) for locations where subduction zone earthquakes are expected, to take into consideration the occurrence of bar buckling.

Ductility is a measure of the ability of a material, section, structural element or structural system to sustain deformations prior to collapse without substantial loss of resistance. The Australian design standard, AS 3600, imposes minimum ductility requirements on structural concrete members to try to prevent premature non-ductile failure and hence to ensure adequate strength and ductile-type collapse with large deflections. The requirements also enable members to resist imposed deformation due to differential settlement, time effects on the concrete and temperature effects, whilst ensuring sufficient carrying capacity and a safe design. Current AS 3600 requirements allow a limited increase or reduction in elastically determined bending moments in critical regions of indeterminate beams, accommodating their ability to redistribute moment from highly stressed regions to other parts of the beam. Design moment redistribution limits and ductility requirements in AS 3600 for bonded partially prestressed beams are a simple extension of the requirements for reinforced members. The possibility of premature non-ductile failure occurring by fracture of the reinforcement or prestressing steel in partially prestressed members has not adequately addressed. The aim of this research is to investigate the overload behaviour and deformation capacity of bonded post-tensioned beams. The current ductility requirements and design moment redistribution limits according to AS 3600 are tested to ensure designs are both safe and economical. A local flexural deformation model based on the discrete cracked block approach is developed to predict the deformation capacity of high moment regions. The model predicts behaviour from an initial uncracked state through progressive crack development into yielding and collapse. Local deformations are considered in the model using non-linear material laws and local slip behaviour between steel and concrete interfaces, with rigorous definition of compatibility in the compression and tension zones. The model overcomes limitations of past discrete cracked block models by ensuring compatibility of deformation, rather than strain compatibility. This improvement allows the modeling of members with multiple layers of tensile reinforcement and variable depth prestressing tendons having separate material and bond properties. An analysis method for simple and indeterminate reinforced and partially prestressed members was developed, based on the proposed deformation model. To account for the effect of shear in regions of high moment and shear present over the interior supports of a continuous beam, a modification to the treatment of local steel deformation in the flexural model, based on the truss analogy, was undertaken. Secondary reactions and moments due to prestress and continuity are also accounted for in the analysis. A comparison of past beam test data and predictions by the analysis shows the cracking pattern and deformation capacity at ultimate of flexural regions in reinforced and partially prestressed members to be predicted with high accuracy. The analysis method accurately predicts local steel behaviour over a cracked region and deformation capacity for a wide range of beams which fail either by fracture of steel or crushing of the concrete. A parametric study is used to investigate the influence of different parameters on the deformation capacity of a typical negative moment region in a continuous beam. The structural system consists of a bonded post-tensioned, partially prestressed band beam. The primary parameters investigated are the member height and span-to-depth ratio; relative quantity of reinforcing and prestressing steel; material properties and bond capacity of the steels; and lastly the compression zone properties. Results show that the effects of the various parameters on the overload behaviour of partially prestressed beams follow the same trends as reinforced beams. A new insight into the local steel behaviour between cracks is attained. The deformation behaviour displays different trends for parametric variations of the local bond capacity, bar diameter and crack spacing, when compared to past analytical predictions from comparable studies. The discrepancy in findings is traced back to the definition of the plastic rotation capacity and the sequencing of the yielding of the steels. Compared to the other local deformation models, the current model does not assume a linear distribution of strain at a crack. The current findings highlight an important difference between predicted behaviours from different deformation compatibility requirements in local deformation models which has not yet been discussed in the literature. The local deformation model evaluates the relationship between maximum steel strain at a crack and average steel deformation over a crack spacing for the entire loading history. The total steel percentage, hardening properties of the steel and concrete strength are shown by the model to have the greatest effect on these steel strain localisation factors. Section analysis, as currently used in design, can be improved with the proposed simplification of the relationships to identify and quantify the effects of steel fracture on deformation capacity and strength. The numerical effort required to simulate the overload behaviour of practical beam designs with multiple reinforcement elements and a prestressing tendon are currently too great to be used in an extensive numerical study. The numerically more efficient smeared block approach is shown to accurately predict the ultimate carrying capacity of prestressed beams failing by crushing of the concrete. Consequently, this method is adopted to study the allowable limits of moment redistribution in the present investigation, Simplified relationships of the steel strain localisation factors evaluated in the parametric study of deformation capacity is used to predict maximum steel strains and premature failure. The limits of moment redistribution in bonded, post-tensioned partially prestressed band beams are explored by comparing the design load and predicted carrying capacity, for different section ductilities and design moment redistribution. In addition, the effects of different concrete strengths, up to 85 MPa, along with as three reinforcing and prestressing steel ductilities are quantified and compared to current Australian and international design requirements. Limitations in the carrying capacity are investigated for different reinforcement and prestress uniform elongation capacities. More than one thousand beam simulations produce results showing that current design moment redistribution and ductility requirements in the Australian design code for concrete structures (AS 3600) are sufficient for normal strength concretes (less than 50 MPa). A suggestion for design moment redistribution limits, section ductility requirements and steel ductility limits is made for members constructed from higher strength concretes. A special high steel ductility class is proposed for both the reinforcement and prestressing steel to allow moment redistribution in higher strength concrete. No moment redistribution is proposed for members reinforced with low ductility (Class L) steel. An increase of the current elongation limit of Class L steel from 1.5 % to 2.5% is suggested to ensure strength and safety. An increase in the current ductility requirements from fsu/ fsy=1.03 and elongation equal to 1.5% to fsu/fsy=1.05 and 2.5% elongation for low ductility Class L steel is suggested to ensure strength and safety. / Thesis (Ph.D.)--Civil and Environmental Engineering, 2004.

The objective of this study is to formulate a general 3D material-structural analysis framework for the thermomechanical behavior of steel-concrete structures in a fire environment. The proposed analysis framework consists of three modeling parts: fire dynamics simulation, heat transfer analysis, and a thermomechanical stress analysis of the structure. The first modeling part consists of applying the NIST (National Institute of Standards and Technology) fire dynamics simulator (FDS) where coupled Computational Fluid Dynamics (CFD) with thermodynamics are combined to model the fire progression within the steel-concrete structure. The goal is to generate the spatial-temporal (ST) solution variables (temperature, heat flux) on the surfaces of the structure. The FDS-ST solutions are generated in a discrete numerical form. Continuous FDS-ST approximations are then developed to represent the temperature or heat-flux at any given time or point within the structure. An extensive numerical study is carried out to examine the best ST approximation functions that strike a balance between accuracy and simplicity. The second modeling part consists of a finite-element (FE) transient heat analysis of the structure using the continuous FDS-ST surface variables as prescribed thermal boundary conditions. The third modeling part is a thermomechanical FE structural analysis using both nonlinear material and geometry. The temperature history from the second modeling part is used at all nodal points. The ABAQUS FE code is used with newly developed external user subroutines for the second and third simulation parts. The main objective is to describe the nonlinear temperature-dependency of the specific heat of concrete materials, especially high-strength concretes, that drastically affects their transient thermal solution. New algorithms are also developed to apply the continuous FDS-ST surface nodal boundary conditions in the transient heat FE analysis. The proposed modeling framework is applied to predict the temperature and deflection of the well-documented Cardington fire tests and to predict the time-to-collapse of the recent Oakland bridge fire caused by a fuel-truck accident.

Insulated concrete forms (ICFs) are green building components that are primarily used for residential wall construction. Unlike most polystyrene based ICF variants, the Faswall ICFs used in these experiments were significantly denser because they were made from recycled wood particles and cement. The current design approach for structures constructed with this type of wall form only allows the designer to consider the contribution of the reinforced concrete cores. Previous research has shown that this approach may be conservative. This project experimentally evaluated the lateral structural response of these types of grid ICF walls under increasing amplitude of in-plane cyclic loading. Two different height-to-length (aspect) ratios (approximately 2:1 and 1:1) were investigated, as was the effect of simultaneous gravity load. Furthermore, the reinforced concrete grid was exposed for each aspect ratio in order to examine the contribution of the ICF blocks to the lateral response. Analyses of hysteretic behaviors and failure modes indicated conservatism in the current design approach for estimating lateral strength and ignoring the beneficial contribution of the ICF blocks to overall performance. The presence of the wall forms increased the lateral shear capacity of the walls by an average of 42% (compared to the walls with forms removed), while also increasing the deformation capacity by an average of 102%. Furthermore, by considering an additional gravity load of 10 kips-per-lineal-foot (klf), the shear resistance of the walls increased by 32% (versus walls only subjected to self-weight), on average, and the deformation capacity of the walls increased by an average of 19%. Comparisons of the experimental results to several design equations led to the recommendation of a design equation that was previously accepted for another type of ICF system.

Die Umsetzung der Ziele des DFG-Schwerpunktprogramms (SPP) 1542 „Leicht Bauen mit Beton – Grundlagen für das Bauen der Zukunft mit bionischen und mathematischen Entwurfsprinzipien“ erfordert eine Anpassung grundlegender, im Stahlbetonbau etablierter Konstruktionsformen. Ein Beispiel hierfür ist die Stahlbetonskelettbauweise. Aktuelle Konstruktionen weisen klare Strukturen aus Stützen, Unterzügen und Decken, im Regelfall mit rechteckigen, über die Bauteillänge konstanten Querschnitten auf. Um diese typischen Konstruktionen zu optimieren, können die im Rahmen des SPP 1542 an der TU Braunschweig entwickelten Bauteil-, Füge- und Herstellungstechnologien genutzt werden. Um dies exemplarisch zu zeigen, wurde der Demonstrator uni-con² entwickelt und hergestellt. Der Demonstrator stellt einen Ausschnitt eines innovativen Tragwerks aus Hochleistungsbeton dar, das aus Platten- und Stabelementen, die nach dem Prinzip „form follows force“ an die einwirkenden Beanspruchungen angepasst werden, zusammengesetzt wird (Bild 1). Die vorgefertigten Elemente werden trocken gefügt. So kann der Aufbau beschleunigt und eine direkte Belastung ermöglicht werden. Die Verwendung von Trockenfugen erfordert eine hohe Präzision bei der Herstellung der Bauteile. Dies kann durch den Einsatz von hochpräzise hergestellten Schalungen sichergestellt werden. Der symmetrische Aufbau der Tragkonstruktion sowie die gleichbleibenden Spannweiten ermöglichen die multiple Verwendung der komplexen Schalungen. In Kombination mit der Reduktion des Zementverbrauchs ermöglicht dies zudem die Einsparung von natürlichen Ressourcen und Energie. / The implementation of the objectives of the DFG Priority Programme (SPP) 1542 “Concrete light – Future concrete structures using bionic, mathematical and engineering formfinding principles” requires the modification of fundamental structural forms established in reinforced concrete construction. An example of this is the reinforced concrete framework construction. Current constructions show distinct structures consisting of columns, beams and slabs, usually having rectangular cross-sections that are constant over the entire length of the component. In order to optimise these standard structures, the construction, joining and manufacturing technologies developed within the scope of SPP 1542 at Technical University (TU) Braunschweig can be used. The demonstrator uni-con² was developed and manufactured to exemplify this. The demonstrator represents a cutout of an innovative load-bearing structure made of high-performance concrete, which is composed of slab and beam elements designed according to the “form follows force” principle and adapted to the relevant stresses (Fig. 1). The prefabricated elements are joined dry. In this way the assembly can be accelerated and a direct loading can be made possible. The use of dry joints requires high precision in the production of the components. This can be achieved by high precision formwork. The symmetrical configuration of the structure and the constant spans allow the multiple use of the complex formwork. In combination with the reduction of cement consumption, this also enables the saving of natural resources and energy.