Equivalent Lateral Force Method (ELF) and Response Spectrum Analysis (RSA) are the two most popular methods of seismic design of structures. This study aims to present a comparative study of the two methods using hand-calculated approach as well as computer analysis according to ASCE 7-10 Standards. The two methods have been compared in terms of base shear and story forces by analyzing various models for different number of stories and different support conditions. It was found that ELF gives conservative results in comparison to RSA. This result was more obvious in case of four-story frames. Hence, for structures of increased elevation, the analysis from ELF may not be sufficient.

Actualmente la población limeña no cuenta con viviendas propias y seguras; por ello, surge el auge del rubro de la construcción masiva con grandes edificaciones multifamiliares, cuya resistencia al impacto telúrico de enorme magnitud de 8 a 9 grados sigue en prueba sísmica; por ende, es muy relevante realizar la comparación del análisis del método modal espectral de la estructura (desplazamientos y aceleraciones respecto al suelo) y un análisis del método tiempo-historia donde se obtendrán las deformaciones máximas de la estructura de los edificios en este presente estudio; asimismo, evaluará la vulnerabilidad de la construcción estructural mediante acelerogramas sintéticos utilizando como espectro objetivo el espectro de peligro uniforme obtenido en el Parque de la Reserva, Cercado de Lima, por medio de un estudio peligro sísmico para un periodo de retorno de 475 años, reconociendo el comportamiento estructural ante un sismo de gran magnitud. El presente estudio titulado: Análisis de la amplificación sísmica de edificios del Cercado de Lima – Lima y La Punta – Callao por medio del análisis modal espectral y tiempo – historia mediante acelerogramas sintéticos; cuyo objetivo es realizar la comparación de dichos métodos en 4 edificios (2 de 5 niveles y 2 de 12 niveles) cuya configuración estructural es de muros de concreto armado, los cuales se estudiaran en dos distintos tipos de suelo (Cercado de Lima y La Punta) con la finalidad de obtener resultados de derivas, fuerzas, desplazamientos y aceleraciones para determinar la amplificación sísmica en los suelos mencionados, y así optar por el método de análisis más óptimo. Asimismo, el propósito del presente estudio es conocer el comportamiento de la edificación acorde con la realidad peruana; es decir edificaciones con periodos cortos; el cual evaluará la vulnerabilidad mediante acelerogramas sintéticos, reconociendo el comportamiento estructural ante una eventualidad sísmica de gran magnitud. / Currently, the population of Lima does not have their own and secure homes; For this reason, the boom in the field of massive construction emerges with large multi-family buildings, whose resistance to the telluric impact of enormous magnitude of 8 to 9 degrees continues in seismic testing; therefore, it is very relevant to make the comparison of the analysis of the spectral modal method of the structure (displacements and accelerations with respect to the ground) and an analysis of the time-history method where the maximum deformations of the structure of the buildings will be obtained in this present study. ; Likewise, it will assess the vulnerability of structural construction using synthetic accelerograms using the uniform hazard spectrum obtained in Parque de la Reserva, Cercado de Lima as the objective spectrum, through a seismic hazard study for a return period of 475 years, recognizing structural behavior in the face of a large earthquake. The present study entitled: Analysis of the seismic amplification of buildings in Cercado de Lima - Lima and La Punta - Callao by means of spectral modal analysis and time - history using synthetic accelerograms; the objective of which is to compare these methods in 4 buildings (2 of 5 levels and 2 of 12 levels) whose structural configuration is made of reinforced concrete walls, which will be studied in two different types of soil (Cercado de Lima and La Punta ) in order to obtain results of drifts, forces, displacements and accelerations to determine the seismic amplification in the mentioned soils, and thus opt for the most optimal analysis method. Likewise, the purpose of this study is to know the behavior of the building in accordance with the Peruvian reality; that is to say buildings with short periods; which will assess vulnerability using synthetic accelerograms, recognizing the structural behavior in the event of a large seismic event. / Tesis

The Insurance Bureau of Canada released a report in 2013 that evaluated the seismic risk of two major metropolitan areas of Canada, with projected losses of $75bn in British Columbia along the Cascadia subduction zone, and $63bn in the east through the Ottawa-Montreal-Quebec corridor. Such reports should prompt researchers and designers alike to rethink the way that seismic design is approached in Canada to develop resilient and sustainable cities for the future. To mitigate the economic losses associated with earthquake damage to buildings in seismically active areas, controlled rocking steel braced frames have been developed as a seismically resilient low-damage lateral-force resisting system. Controlled rocking steel braced frames (CRSBFs) mitigate structural damage during earthquakes through a controlled rocking mechanism, where energy dissipation can be provided at the base of the frame, and pre-stressed tendons pull the frame back to its centred position after rocking. The result is a building for which the residual drifts of the system after an earthquake are essentially zero, and the energy dissipation does not result from structural damage. Design methods for the base rocking joint and the capacity-protected frame members in CRSBFs have been proposed and validated both numerically and experimentally. However, the is no consensus on how to approach the design of the frame members, questions remain regarding how best to design CRSBFs to prevent building collapse, and no experimental work has been done regarding how to connect the CRSBF to the rest of the structure to accommodate the rocking motion. Because the force limiting mechanism of a CRSBF is rocking only at the base of the frame, the frame member forces are greatly influenced by the higher-mode response, resulting in more complex methods to design the frame members. This thesis begins by outlining two new design procedures for the frame members in controlled rocking steel braced frames that target both simplicity and accuracy. The first is a dynamic procedure that requires a truncated response spectrum analysis on a model of the frame with modified boundary conditions to consider the rocking behaviour. The second is an equivalent static procedure that does not require any modifications to the elastic frame model, instead using theory-based lateral force distributions to consider the higher modes of the rocking structure. Neither method requires empirical calibration to estimate the forces at the target intensity. The base rocking joint design is generally in good agreement between the various research programs pioneering the development of the CRSBFs. However, the numerous parameters available to select during the design of the base rocking joint give designers an exceptional amount of control over the performance of the system, and little research is available on how best to select these parameters to target or minimise the probability of collapse for the building. This thesis presents a detailed numerical model to capture collapse of buildings with CRSBFs as their primary lateral force resisting system and uses this model to generate collapse fragility curves for different base rocking joint design parameters. The parameters include the response modification factor, the hysteretic energy dissipation ratio, and the post-tensioning prestress ratio. This work demonstrates that CRSBFs are resilient against collapse, as designing the base rocking joint with response modification factors as large as 30, designing the post-tensioning to prevent yielding at moderate seismic hazard levels, and using zero energy dissipation could lead to designs with acceptable margins of safety against collapse. While the design procedures are shown to be accurate for estimating the frame member force demand for the targeted intensity level, there is still a high level of uncertainty around what intensity of earthquake a building will experience during its lifespan, and there is no consensus on what intensity should be targeted for design. To address this, the ability of the capacity design procedures to provide a sufficiently low probability of collapse due to excessive frame member buckling and yielding is evaluated and compared to the probability that the building will collapse due to excessive rocking of the frame. The results of the research presented here suggest that the probability of collapse due to either frame member failure or excessive rocking should be evaluated separately, and that targeting the intensity with a 10% probability of exceedance in 50 years is sufficient for the design of the frame members. Finally, critical to the implementation of CRSBFs in practice is how they may be connected to the rest of the structure to accommodate the uplifting of the CRSBF while rocking under large lateral forces. An experimental program was undertaken to test three proposed connection details to accommodate the relative uplifts and forces. The connections that accommodate the uplifts through sliding performed better than that which accommodated the uplifts though material yielding, but the best way to transfer the forces and accommodate the uplifting without influencing the overall behaviour of the system is to position the connection such that it does not need to undergo large uplifts and carry lateral force simultaneously. A detailed numerical model of the experimental setup is presented and is shown to simulate the important response quantities for each of the tested connections. Using the results of this work, designers worldwide will be confident to design CRSBFs for structures from the base rocking joint to the selection of floor-to-frame connections for a complete system design while ensuring a safe and resilient building structure for public use and well-being. / Thesis / Doctor of Philosophy (PhD) / Traditional approaches to seismic design of buildings have generally been successful at preventing collapse and protecting the lives of the occupants. However, the buildings are often left severely damaged, often beyond repair. To address these concerns, controlled rocking steel braced frames have been proposed as part of a new construction technique to mitigate or prevent damage to steel buildings during earthquakes, but several aspects of the design and overall safety have yet to be explored or demonstrated. This thesis proposes and validates new tools to design controlled rocking steel braced frames and provides recommendations on how best to design them to achieve a safe probability against collapse. Details are proposed and presented for components to connect the controlled rocking steel braced frames into the rest of the structure. The findings of this thesis will aid practitioners looking to deliver resilient and sustainable structural designs for buildings in our cities of the future.