Thesis (MScEng)--Stellenbosch University, 2013. / ENGLISH ABSTRACT: Factors influencing surface run-off of bitumen emulsions were studied in order to understand binders for use in the construction of surfacing seals. Run-off of the binder from the road surface causes an inconsistent film thickness leading to ravelling (Johannes, Hanz & Bahia n.d.) and bleeding at the upstream and downstream regions, respectively. There is currently no accepted specification for surface run-off viscosity. Practice mainly relies on empirical tests and experience. As the establishment of such a specification encompasses performance of the binder in various environments or field conditions, this study was undertaken to determine performance of the selected binder. Viscosity was kept constant by spraying the emulsion at a constant temperature and also holding the pavement temperature constant. In order to study the run-off behaviour of the binder, run-off tests were conducted at various gradients, texture depths and spray rates. Surfacing seals of various texture depths were constructed in the laboratory. Using a spray bar, the emulsion was sprayed at various spray rates. The sample surfaces were tilted to various gradients. Results portrayed the effects of the three factors (spray rate, gradient and texture depth) on the amount of runoff. An increase in the magnitude of the factors resulted in a variation in the runoff (increase or decrease). One notable finding was that the runoff from the 9.5 mm seal was less than that from the 13.2 mm seal. The other significant finding was that spray rate had the largest effect on runoff, followed by texture depth, and gradient. / AFRIKAANSE OPSOMMING: Sekere eienskappe wat oppervlakdreinering van bitumen emulsies op paaie beinvloed, is bestudeer om sodoende binders wat gebruik word in die konstruksie van die seëls beter te verstaan. Afloop van die binder vanaf die padoppervlak kan lei tot die vorming van ‘n laag met ongelyke dikte wat moontlike rafeling (Johannes, Hanz & Bahia nd) en bloeing vanuit die onderkant van die pad tot gevolg kan hê. Daar is tans geen aanvaarde spesifikasies wat hierdie verskynsels inperk nie. Konstruksie praktyk berus hoofsaaklik op empiriese toetse en ondervinding. Hierdie studie is dus onderneem om prestasie van die geselekteerde binder vas te stel. Viskositeit was konstant gehou deur die aangewende emulsie en padtemperatuur konstant te hou. Ten einde die afloopgedrag van die binder te bestudeer, is toetse uitgevoer op verskeie hellings, tekstuurdieptes en aanwendingskoerse. Seëls van die verskillende tekstuurdieptes is gebou in die laboratorium, en emulsies op hierdie oppervlaktes aangewend. Die toetsoppervlakte is gekantel om die vereiste helling te kry. Resultate vir die drie faktore wys die invloed op afloop. ‘n Toename in die grootte van die faktore het gelei tot 'n variasie in die afloop (toename of afname). Een noemenswaardige bevinding was dat die afloop van die seël van 9,5 mm minder was as dié van die seël van 13,2 mm. Belangrike bevindinge sluit ook in dat die spuitkoers die grootste invloed het op afloop, gevolg deur die tekstuur diepte en die gradiënt.

Thesis (MEng)-- Stellenbosch University, 2013. / ENGLISH ABSTRACT: Two common methods of road pavement, granular material stabilisation used in road construction throughout South Africa today include Cold in Place Recycling (CIPR) and stabilisation with cement or bitumen and an active filler to create Bitumen Stabilised Materials (BSM). As part of the updating of the South African Pavement Design Method (SAPDM) an experimental section, investigating the structural capacity of cement and lime stabilised and BSM pavement layers, was constructed and will be monitored over a two year period. As part of this study Falling Weight Deflectometer (FWD) measurements were taken on the various experimental stabilised pavement layers constructed. The FWD deflection data, measured at various time intervals over a 360 day period, forms the basis of the study presented here. The objective of this thesis was to identify typical back-calculated layer stiffnesses and their variability over time for the various in-situ recycled and stabilised base layers constructed within the experimental section. Stabiliser type, content and layer thicknesses were varied across experimental sub-sections. Trends in back-calculated stiffness of cement stabilised base layers consistently showed significant reductions in layer stiffness subsequent to construction traffic loading. Subsequent to the initial reduction in stiffness little change in stiffness was noted under normal traffic loads. Observations on the trends in back-calculated stabilised layer stiffness per material type over time indicated that seasonal moisture and temperature fluctuations have an effect on the stiffness of the pavement structure as a whole. BSM materials showed significant variability over time in-line with seasonal variability in the supporting subgrade stiffness in the southbound lane. BSM materials with 1% cement added in the northbound lane show initial stiffness reductions due to direct rainfall application however a significant increase in layer stiffness occurs up to 360 days after construction. BSMs with 2% cement in the northbound lane show significant increases in layer stiffness over the 360 day observation period. No significant difference in stiffness trend was observed between BSM emulsion a BSM foam materials. The BSM emulsion with 0.9% residual bitumen and 1% cement was observed to show rapid reduction in stiffness upon opening to traffic and reverting to stiffness values similar to an unbound material of approximately 350 MPa. Cement and lime stabilised materials showed typical post 28 –day average stiffnesses per sub-section ranging between 600 MPa and 1800 MPa. BSM foam with 1% cement added were observed to have average stiffnesses per sub-section in the range of 400MPa to 2200 MPa and BSM emulsion with 1% cement with stiffnesses between 400 MPa to 1700 MPa over the 360 day period. BSMs with 2% cement added showed stiffness ranges between 900 MPa to 4300 MPa for BSM foam and 900 MPa to 3900 MPa for BSM emulsions over the 360 day period. The spatial variability of back-calculated stiffness per sub-section of a particular stabilisation design was significant and was observed, through the Co-efficient of Variation (COV), to increase over time. The effect of the observed variability when incorporated into a pavement design scenario, requiring a design reliability of 90%, showed 50% of the pavement structure would be overdesigned by a factor of 4. With respect to the current philosophies on the development of stiffness over time of cement and lime stabilised and BSM pavement layers some useful observations were made. Cement stabilised materials correlate well with stiffness development theories predicted by previous studies. Theories relating to the stiffness development of BSMs however did not predict the levels of variability in base layer stiffness observed on the experimental section. The continued observation of the experimental section for another year will give greater insight to the stiffness trends of the stabilised materials discussed above.

Long term durability is a major concern for wide-scale use of recycled aggregate materials in civil engineering construction. The purpose of this study is to provide an insight into the damaging effects of combined wet-dry cycles and repeated mechanical loading in a recycled aggregate concrete (RAC) base course material made from recycled crushed concrete aggregate and cement. A coordinated experimental program followed by a mechanistic pavement modeling and life cycle analysis was conducted as part of this research study. This laboratory investigation was divided into three phases each consisting of both wet-dry exposed specimens (WD), and control or non wet-dry exposed specimens (NWD). Phase I experiments involved monotonic loading tests under compression and flexure to evaluate the strength properties. Phase II involved testing a total of 108 cylindrical specimens in cyclic compressive loading at three different stress ratios. After each regime of cyclic loading, residual compressive strengths were determined. In addition, the load-deformation hysteresis loops and the accumulated plastic deformation were continuously monitored through all loading cycles. Phase III included a flexural fatigue test program on 39 beam specimens, and fracture testing program on 6 notched beam specimens, each one having 19-mm initial notch. Traditional SR-N curves, relating the Stress Ratio (SR) with the number of cycles to failure (N or Nf), were developed. Fatigue crack growth rate and changes in Stress Intensity Factors were obtained to determine Paris Law constants and fracture toughness. A mechanistic analysis of a typical highway pavement incorporating RAC base was performed with KENPAVE program, followed by a Life Cycle Analysis (LCA) using the GaBi software. It was found that the specimens subjected to wet-dry cycles suffered significantly higher damage expressed in terms of accumulated plastic deformation, and loss of residual compressive strength, modulus, fatigue endurance limit, and design life, compared to specimens not exposed to wet-dry cycles. Although such degradation in material properties are important considerations in pavement design, a concurrent Life Cycle Analysis demonstrated that recycled aggregate concrete base course still holds promise as an alternative construction material from environmental stand point. / Includes bibliography. / Dissertation (Ph.D.)--Florida Atlantic University, 2014. / FAU Electronic Theses and Dissertations Collection

Drivers for sustainability have made it necessary for the construction industry to adapt its traditional processes to become both more efficient and produce less waste. Performance based design and specification in the UK for motorways and trunk roads permits a very flexible approach to pavement design, material selection and performance related testing aimed at utilising materials to their maximum potential. However, it is clear that within the emerging philosophy of using materials that are 'fit for purpose' there are many technical challenges for design and specification. There is a need to develop suitable methods of evaluating materials prior to their being used on site. This project was born out of this requirement, with a particular emphasis on coarse granular materials due to their common role in capping construction and also their unique difficulty for measurement under laboratory conditions due to their large range of particle size. A novel assessment test for coarse capping materials for roads that can be used to indicate their likely short-term in situ performance, under controlled laboratory conditions before construction on site, has been developed during this research programme. Key findings relating to the behaviour of coarse capping materials, the use of stiffness measuring devices and variables that influence the measurement of composite stiffness are discussed in detail. The research highlights the necessity for adequate drainage and protection of foundation materials against increase in water content. When adopting a performance specification the timing of the pavement assessment is critical, both on site and in the laboratory. The performance measured on site should perhaps only be considered as a 'snapshot' relating to the stress state in the material at the time of testing.

Le dragage des sédiments est nécessaire afin de maintenir le transport et les activités maritimes mais les sédiments extraits sont souvent pollués en métaux lourds et en composés organiques. Face à la nécessité du dragage et à la pollution, la société Solvay a mis au point un procédé permettant de traiter les sédiments dragués pour envisager une valorisation : le procédé Novosol®. Ce procédé a pour but de stabiliser les métaux présents dans les sédiments par phosphatation (ajout d’acide phosphorique H3PO4) et de dégrader la matière organique par calcination à 650°C. Un acide phosphorique pur est habituellement utilisé pour l’étape de phosphatation. Cependant, dans la présente étude plusieurs acides phosphoriques de nature et de sources différentes fournis par la société PRAYON ont été utilisés. Les principales caractéristiques de deux sédiments traités avec plusieurs types d’acides phosphoriques sont présentées dans cette thèse. D’un point de vu mécanique les formulations effectuées avec les sédiments traités sont conformes aux normes routières. L’étude environnementale a montré que les quantités de métaux lourds relarguées par les matériaux formulés à partir des sédiments traités sont inférieures aux seuils fixés par la législation en vigueur. Les résultats obtenus avec les différents types d’acides sont similaires. Cela permet d’envisager l’utilisation des sédiments de dragage traité Novosol® en technique routière. / Dredging of sediments is necessary in order to maintain maritime activities and for flood prevention. However increased industrial activities are causing accumulation of pollutants in the sediments. The main contaminants are heavy metals and organic compounds. Because of the cost of storage, treatment and valorization can be economically sound. This study focuses on the technology to treat heavy metals from dredged sediments using phosphoric acid (H3PO4) (the Novosol®process developed by Solvay company) with a goal to stabilize heavy metals by capturing them in a calcium phosphate matrix and to destroy organic matter by calcination at 650°C. Several studies have been conducted in this field. The stabilized materials obtained have been used in civil engineering. However these studies have never assessed the effect of the composition of the phosphoric acid on the treatment. In this thesis dissertations the effect of two types of phosphoric acids with various purities and origins provide by PRAYON company were compared. The investigation focuses on the effect of the phosphoric acids on the environmental behavior of metals and on the geotechnical properties of the dredged sediment. The environmental study has shown that the concentration of heavy metals released by materials made from treated sediments are below the regulation limits . The results obtained with the different types of acids are comparable. This allows to consider the use of treated dredged sediment by process Novosol® as road materials.

Klimatpåverkan och energiförbrukning är ett av de stora miljöproblemen runt om i världen idag. Sedan den industriella revolutionens start har mängden utsläpp av bland annat koldioxid ökat exponentiellt med årens lopp och skapat obalans i klimatet, inte minst på grund av restprodukter och skadliga ämnen som används inom bland annat byggindustrin. Syftet med denna studie är att ta reda på vilka arbetsmoment som har störst påverkan på miljön för att sedan, om möjligt, ta fram förslag på hur det kan förbättras. Frågeställningen vi utgått från vid genomförandet av denna studie har varit; “Av de arbetsmetoder vid ett bygge av en väg, vilken del är mest skadlig för miljön?”. Den huvudsakliga metoden för detta arbete har varit en fallstudie där en undersökning om ett projekt har gjorts. Ett antal klimatkalkyler med olika vägmaterialsegenskaper gjordes som sedan jämfördes mot varandra. Av dessa kalkyler kunde slutsatsen att kallasfalt släpper ut mycket mindre koldioxid jämfört med vanlig asfalt men det krävs mer forskning kring detta för att kunna dra en säkrare slutsats. / Climate impact and energy consumption are one of the biggest environmental problems around the world today. Since the start of the industrial revolution, the amount of carbon dioxide emissions has increased exponentially over the years. These emissions created imbalances in the climate, not least because of residues and harmful substances used in the construction industry. The purpose of this study is to find out which methods have the greatest impact on the environment, and then, if possible, make suggestions on how it can be improved. The issue we have researched in this study has been; "what method of building a road is most harmful to the environment?”. The main method of this work has been a case study in which a survey of a project has been conducted. A number of climate calculations with different road material properties were made which were then compared to each other. The conclusion we were able to make is that cold-asphalt releases much less carbon dioxide than normal asphalt, but more research is needed to draw a more accurate and reliable conclusion.

Thesis (MScEng)--Stellenbosch University, 2012. / ENGLISH ABSTRACT: Chip and spray surfacing seals has been widely used in South Africa as the preferred surface treatment for rural roads. The design of these seals has also experienced renewed interest and continuous development in several other countries over the past two decades. In South Africa seals are continually used as increasing attention is given to the periodic maintenance of existing surfaced roads. There is also a significant increase in the use of surfacing seals in North America as the need to develop more energy and resource efficient surfacing options becomes a priority. Despite this growing use of surface seals, the seal design and especially the selection of binder type and grade does not always follow scientific processes. Seals are often designed based on client preference, previous experience, material availability and industry trends. With an ageing road network and limited funding to ensure timeous maintenance, the focus in South Africa is moving towards more stringent and scientific design processes. The USA and Europe, forced by increasing traffic volumes and heightened performance demands, are moving towards performance- based specification to account for deficiencies in their current surface seal design methods. One of the major failure mechanisms of surface seals is ravelling which takes place when the binder and the aggregate bond becomes weak and are broken by the forces generated by traffic. This leads to loose aggregate on the road which in turns leads to bare surface patches and broken windscreens. To prevent and address this as part of the development of performance-based specifications, the need for a simple and inexpensive technique for evaluating bitumen and bitumen emulsion bond strength development over time, as well as binder-aggregate compatibility, was identified. Although various tests exist for investigating adhesion between bituminous emulsions and aggregate chips most of the tests does not deliver the level of information required by the performance-based specifications. The Bitumen Bond Strength (BBS) test method was therefore developed with the aim to address some of the limitations encountered in evaluating bond strength between binders and aggregates. The BBS test (AASHTO TP-91, 2011) was developed by the University of Wisconsin – Madison (UWM) in partnership with the University of Ancona – Italy (UAI) and the University of Stellenbosch – South Africa (US) specifically for evaluating bond strength between aggregates and hot applied binders and emulsions, respectively. US became involved in BBS test efforts in 2008 to assist in the development and practical evaluation of the BBS test method. UAI contributed significantly to the development of the test apparatus through their work in conjunction with UWM. Due to time and resources available, the involvement of the US was limited to various discussion sessions, a study tour, the evaluation of the BBS test, and conducting a series of control tests. By using the Bitumen Bond Strength test it was possible to evaluate the practicality and repeatability of the developed procedure and the results measured was successfully used to evaluate the bond strength development of modified and unmodified bitumen emulsions on tillite and granite aggregates. It was also possible to correlate the results achieved at the University of Stellenbosch with results from the University of Wisconsin-Madison due to the fact that testing took place at both institutions. The development of the test and the inter-laboratory test results in essence reinforced the hypothesis that the BBS test protocol can be used to effectively evaluate bond strength of different emulsion types and aggregate types. Except for the loading rate which is a known critical influence, the emulsion type and curing intervals are both identified as the most significant other factors contributing to bond strength development. Aggregate type is also identified as a significant factor that will influence the bond strength development. Interactions between emulsion type and curing interval are identified as the most significant interaction. A lot of further validation test on the BBS test method is still required for the test to be integrated into a performance-based specification system for surface seals. / AFRIKAANSE OPSOMMING: “Chip and Spray” oppervlak seëls is die verkose seël tipe vir gebruik op Suid Afrikaanse plattelandse paaie. Die ontwerp van hierdie tipe seëls is ook tans besig om hernude aandag te trek in heelwat lande. In Suid Afrika word die tipe seël al meer gebruik soos die behoefte na herseël projeke op die verouderde pad netwerk groei . Daar is ook heelwat groei in die gebruik van “Chip en Spray” seëls in Noord Amerika aangesien daar n behoefte is om n meer energie en materiaal effektiewe seëls te gebruik. Ten spyte van die groeiende gebruik van hierdie seëls het daar min wetenskaplike ontwikkeling plaasgevind in the ontwerp daarvan. Seëls word meestal ontwerp gebaseer op klient voorkeur , ondervinding, materiaal beskikbaarheid en ook industrie norms. ‘n Verouderde pad netwerk dwing die Suid Afrikaanse industrie om meer deeglike en wetenskaplike ontwerp prosedures te volg. Die VSA en Europa word deur vinnig groeiende verkeersvolumes en verhoogte kwaliteits behoeftes gedwing om prestasie gebaseerde spesifikasies te ontwikkel. Een van die hoof defekte op seëls is klipverlies wat plaasvind as die verbinding tussen die bitumen en aggregaat verswak en gebreek word deur die kragte wat deur verkeer oorgedra word. Dit lei tot los klip op die pad wat weer tot skade aan voertuie lei. Om dit te voorkom en aan te spreek het die behoefte laat ontwikkel vir n maklike en goedkoop tegniek om te meet hoe sterk die verbinding is wat ontwikkel tussen verskillende bitumen, bitumen emulsies en aggregaat monsters. Alhoewel daar alreeds toetse bestaan wat kan toets hoe sterk die verbinding is , gee die meeste van die toetse nie die informasie wat benodig word deur die voorgestelde prestasie gedrewe spesfikasies nie. Die “Bitumen Bond Strength” (BBS) toets metode is daarom ontwikkel om die tekortkoming in die toets van die bitumen en aggregaat verdindinge aan te spreek. Die BBS toets (AASHTO TP-91, 2011) is ontwikkel by die Universiteit van Wisconsin – Madison (UWM) in vennootskap met die Universiteit van Ancona – Italy (UAI) en die Universiteit van Stellenbosch (US) , spesifiek om die die sterkte van die verbinding wat vorm tussen aggregaat en bitumen te meet. Die US het in 2008 betrokke geraak by die BBS toets studie om hulp te verleen met die ontwikkeling en praktiese evalueering van die BBS toets metode. As gevolg van tyd en personeel tekorte is die betrokkendheid by die US beperk tot verskeie besprekings sessies, n studie toer, die evalueering van die BBS toets sowel as die voltooing van n uitgebreide stel toetse. Deur die voltooing van eksperimente met die BBS toets was dit moontlik om die uitvoerbaarheid en herhaalbaarheid van die ontwikkelde prosedure te toets. Die resultate van die toetse is suksesvol gebruik om die ontwikkeling van die verbinding sterkte tussen gemodifiseerde en ongemodifiseerde bitumen emulsies en tilliet en graniet te definïeer en te evalueer. Dit was ook moontlik om die resultate van die Universiteit Stellenbosch en die Universiteit of Wisconsin-Madison suksesvol met mekaar te vergelyk aangesien toetse by beide die instansies voltooi is. Die ontwikkeling van die toets en die inter laboratorium toets resultate het dit moontlik gemaak om die hipotese te bevestig dat die BBS toets prosedure effektief gebruik kan word om die bitumen en aggregaat verdindinge te toets en te evalueer. Behalwe vir die tempo van die lading waarteen die aftrek sterkte getoets word , is die emulsie tipe en die nabehandeling tydperk beide geidentifiseer as die mees beduidende invloede wat bydrae tot die ontwikkeling van die verbinding sterkte. Die aggregaat tipe is ook geidentifiseer as n belangrike faktor wat die verbinding sterkte ontwikkeling sal beïnvloed. Die interaksie tussen die emulsie tipe en nabehandeling tydperk was geïdentifiseer as die mees beduidende interaksie. Daar sal wel nog heelwat eksperimente voltooi moet word met die BBS toets prosedure voordat dit volkome geïntegreer kan word as deel van n prestasie gebaseerde spesifikasie stelsel vir die ontwerp van seëls.

Thesis (MEng)--Stellenbosch University, 2014. / ENGLISH ABSTRACT: Flexible pavement designers have a choice of two wearing course: either asphalt concrete or surfacing seals. The latter have been widely used by several countries as their preferred wearing course over other methods, especially countries with a limited number of average inhabitants per square kilometre. Moreover, the surfacing seals were identified as an efficient cost effective road preventive maintenance technique. Surfacing seals in New Zealand, South Africa and Australia cover about 65%, 80% and 90% of their surfaced road networks respectively. The preference of surfacing seals is due to their competitive initial cost and ease of construction. In South Africa, the life expectancy of surfacing seals varies between 8 and 12 years with an average of 10 years. This has not been the case in a number of surfacing seals constructed in winter, especially when the night recorded temperature is below 10oC. The dominant failure mechanism is ravelling (chip loss) soon after construction due to traffic loading. This chip loss is linked to the poor adhesion bond development rate in the bitumen-aggregate system during winter adverse conditions. In order to address the issue of premature chip loss the need for the development of a robust adhesion test method was identified. For that purpose, recently, researchers in the bitumen industry developed the Bitumen Bond Strength test method. This method was used in this study. This study intends to contribute to the understanding of binder-aggregate adhesion bond development for winter surfacing seals using the BBS test. Binder type, precoat type and conditioning, aggregate type and curing time are amongst the factors influencing winter seals adhesion bond performance. An experimental matrix involving three types of binder, two types of aggregate, four different precoating fluids, two precoat conditionings and two binder-curing times were then developed and investigated. Winter weather parameters affecting adhesion properties were also taken into consideration during the course of the investigation. Throughout the test, the procedure described in AASHTO TP 91-11 was followed. However, in order to enhance the control of the binder application temperature, a new method for hot applied binder sample preparation was developed as part of this study. The findings show that there is a significant difference between adhesion properties of the hot applied binders (70/100 and S-E1) and the emulsion (SC-E1). In most of the cases, the hot applied binders performed better than the emulsion. The failure mode observed was found to be linked to the condition of the precoating. The influence of the precoat type and conditioning, and effect of binder curing time were significantly highlighted. The use of a dry precoat benefited the adhesion bond strength up to around 50% relatively to the corresponding non-precoated combination. However, a decrement in the bond strength due to precoating of up to 28.7% was also observed. A statistical analysis using ANOVA did not illustrate any statistical significant effect of the aggregate type. The interaction effects analysis using ANOVA revealed the aggregate type interacting with precoat type to be the most influential interaction at level two. The precoat conditioning implication to the adhesion development rate, which influences the time for opening to traffic after construction, was illustrated. Insightful aspects on the compatibility between the binder type and precoat type and conditioning during the aggregate precoating practices and on the time for opening to traffic are highlighted. Finally, the repeatability analysis proved the BBS test to be a repeatable testing method with caution. Recommendations for further studies that could support the conclusions drawn in this study were provided. / AFRIKAANSE OPSOMMING: Buigbare plaveiselontwerpers het 'n keuse van twee deklae: óf Asfalt of oppervlak seëls. Laasgenoemde word algemeen gebruik deur verskeie lande as hul voorkeur deklaag, veral die lande met beperkte aantal gemiddelde inwoners per vierkante kilometer. Verder, is die seëls geïdentifiseer as 'n doeltreffende koste-effektiewe deklaag tegniek. Oppervlakseëls in Nieu-Seeland, Suid-Afrika en Australië dek ongeveer 65%, 80% en 90% van hul padnetwerke onderskeidelik. Die seëls se voorkeur is te danke aan hul mededingende aanvanklike koste en eenvoudige vorm van die konstruksie. In Suid-Afrika wissel die seël se lewensverwagting tussen 8 en 12 jaar met 'n gemiddeld van 10 jaar. Dit is egter nie die geval van 'n aantal seëls wat in die winter gebou word nie, veral wanneer die aangetekende nagtemperatuur onder 10o C daal nie. Die dominante swigtingsmeganisme is stroping (klipverlies) kort na konstruksie. Hierdie klipverlies is gekoppel aan die power kleef-ontwikkeling van bitumen gedurende die winter. Ten einde die probleem van voortydige klipverlies aan te spreek het die behoefte vir die ontwikkeling van 'n robuuste toetsmetode ontstaan. Om hierdie rede het navorsers onlangs in die bitumenbedryf die “BBS toetsmetode” ontwikkel en is dié toetsmetode in hierdie studie gebruik. Hierdie studie beoog om by te dra tot die begrip van bindmiddel-klip kleefontwikkeling vir die winter seëls dmv die BBS toets. Die faktore, insluitend maar nie beperk tot bindmiddeltipe, voorafdekking (“PRECOAT”) -tipe en kondisionering, aggregaattipe en kuurtyd beïnvloed winter seëls se kleefeienskappe. 'n Eksperimentele matriks met drie tipes bindmiddels, twee tipes aggregate, vier verskillende voorafdekking-vloeistowwe, twee voorafdekking kondisionering en twee bindmiddel kuurtye is toe ontwikkel en ondersoek. Winter weer parameters wat kleefeienskappe beïnvloed is ook in ag geneem tydens die verloop van die ondersoek. Regdeur die studie is die prosedure AASHTO TP 91-11 gevolg, maar ten einde die beheer van die bindmiddel spuittemperatuur te verbeter, is ‘n nuwe metode vir warmspuit-bindmonsters voorbereiding ontwikkel as deel van hierdie studie. Die bevindinge toon dat daar 'n beduidende verskil tussen die kleefeienskappe van die warm aangewende bindmiddels (70/100 en S-E1) en die emulsie (SC-E1) is. In die meeste van die gevalle het die warmspuit-bindmiddels beter as emulsie gevaar. Daar is gevind dat die swigtingsmeganisme verbind word met die toestand van die voorafdekking. Die invloed van voorafdekkingtipe, kondisionering, en die effek van bindmiddelkuurtyd is duidelik uitgelig. Die gebruik van droë voorafdekking het die kleefkrag tot sowat 50% verhoog relatief tot die ooreenstemmende onbedekte klipkombinasie. Daar is egter ook ‘n verlaging van die kleefkrag weens voorafdekking gevind van tot so hoog soos 28,7 persent. Die statistiese ontleding met behulp van ANOVA het geen statisties beduidende effek van die verksillende aggregaattipe te vore gebring nie. Die interaksie-effek analise, met behulp van ANOVA, het wel die interaksie met voorafdekkingtipe met aggregaat die mees invloedryke bevestig. Die voorafdekking kondisioneering het ver rykende kleefkrag implikasies bloot gelê, wat die tyd vir die opening van die verkeer na konstruksie beïnvloed. Insigwekkende aspekte oor die versoenbaarheid tussen die bindmiddeltipe, voorafdekkingtipe, kondisionering, voorafdekkingpraktyk en tyd tot opening vir verkeer word uitgelig. Ten slotte, die herhaalbaarheidsanalise het die BBS toets as 'n herhaalbare toetsmetode met omsigtigheid bewys. Daar is aanbevelings tot verdere studies, wat uit die gevolgtrekking gekom het, gemaak.