Abstract not available

Cold rolled carbon steel 1018C is widely used in pressurized fuel pipelines. For those structures, stress corrosion cracking (SCC) can pose a significant problem because cracks initiate late in the lifetime and often unexpectedly, but grow fast once they get started. To ensure a safe operation, it is crucial that any damage can be detected before the structural stability is reduced by large cracks. In the early stages of SCC, microstructural changes occur which increase the acoustic nonlinearity of the material. Therefore, an initially monochromatic Rayleigh wave is distorted and measurable higher harmonics are generated. Different levels of stress corrosion cracking is induced in five specimens. For each specimen, nonlinear ultrasonic measurements are performed before and after inducing the damage. For the measurements, oil coupled wedge transducers are used to generate and detect tone burst Rayleigh wave signals. The amplitudes of the received fundamental and second harmonic waves are measured at varying propagation distances to obtain a measure for the acoustic nonlinearity of the material. The results show a damage-dependent increase in nonlinearity for early stages of damage, indicating the suitability for this nonlinear ultrasonic method to detect stress corrosion cracking before structural failure.

Las condiciones ambientales de trabajo de los aceros estructurales y de conducciones en instalaciones energéticas y petrolíferas han puesto en evidencia la necesidad de encontrar una metodología de caracterización de su resistencia a la fisuración, tanto en régimen de dominio elástico como elastoplástico. Este trabajo recoge una metodología experimental y analítica adecuada para ser aplicada a los procesos de fisuración estudiados sobre probetas y estructuras, en particular a aquéllos asociados a la presencia de ambientes agresivos, como corrosión bajo tensión o fisuración inducida por hidrógeno de aceros microaleados. Una vez aplicada y validada, la metodología ofrece resultados de gran interés en la caracterización cuantitativa del comportamiento de fisuración y su correlación con los micromecanismos de rotura presentes. Esta tesis se ha mostrado eficaz en la caracterizacióny establecimiento de un modelo de comportamiento de aceros microaleados utilizados en condiciones de fisuración inducida por hidrógeno, como es el caso de las plataformas petrolíferas en alta mar (estructuras off-shore). / The environmental conditions of employment of structural steel and energy pipelines and oil facilities have highlighted the need to find a methodology for characterizing their resistance to cracking, both in the elastic and the elastoplastic regime. This work includes experimental and analytical methodologies that are appropriate to be applied to cracking processes studied on specimens and structures, in particular to those associated with the presence of aggressive environments, such as stress corrosion cracking or hydrogen induced cracking of microalloyed steels. Once applied and validated, the methodology provides results of great interest in the quantitative characterization of the cracking behavior and its correlation with the fracture micromechanisms taking place. This thesis has been shown to be effective in the characterization and establishment of a behavioral model of microalloyed steels used in conditions of hydrogen-induced cracking, such as oil platforms at sea (off-shore structures).

Today, ethanol, as well as other biofuels, has been increasingly gaining popularity as a major alternative liquid fuel to replace conventional gasoline for road transportation. One of the key challenges for the future use of bioethanol is to increase its availability in the market via an efficient and economic way. However, one major concern in using the existing gas-pipelines to transport fuel-grade ethanol or blended fuel is the potential corrosion and stress corrosion cracking (SCC) susceptibility of carbon steel pipelines in these environments. Both phenomenological and mechanistic investigations have been carried out in order to address the possible degradation phenomena of X-65 pipeline carbon steel in simulated fuel-grade ethanol (SFGE). Firstly, the susceptibilities of stress corrosion cracking of this steel in SFGE were studied. Ethanol chemistry of SFGE was shown to have great impact on the stress corrosion crack initiation/propagation and the corrosion mode transition. Inclusions in the steel can increase local plastic strain and act as crack initiation sites. Secondly, the anodic behavior of carbon steel electrode was investigated in detail under different ethanol chemistry conditions. General corrosion and pitting susceptibility under unstressed condition were found to be sensitive to the ethanol chemistry. Low tendency to passivate and the sensitivity to ethanol chemistry are the major reasons which drive corrosion process in this system. Oxygen plays a critical role in controlling the passivity of carbon steel in ethanol. Thirdly, the detailed study was carried out to understand the SCC mechanism of carbon steel in SFGE. A film related anodic dissolution process was identified to be a major driving force during the crack propagation. Fourthly, more detailed electrochemical impedance spectroscopy (EIS) studies using phase angle analysis and transmission line simulation reveal a clearer physical picture of the stress corrosion cracking process in this environment. Fifthly, the cathodic reactions of carbon steel in SFGE were also investigated to understand the oxygen and hydrogen reactions. Hydrogen uptake into the pipeline steel and the conditions of the fractures related to hydrogen embrittlement were identified and studied.

Bei dem Prozess einer Wasserstoffinduzierten Spannungsrisskorrosion (H-SpRK) handelt es sich um einen zeitabhängigen Vorgang, der zu einer Reduzierung der Duktilität und Widerstandskraft des Spannstahls führt und daraus resultierend ein sprödes und schlagartiges Versagen eines Spannbetonbauwerkes zur Folge haben kann. Der Prozess selbst und insbesondere auch die ihn beeinflussenden Parameter sind für die im Bauwesen verwendeten hochfesten Spannstähle älterer Produktion weitestgehend unerforscht. Die Relevanz für bestehende Bauwerke ist jedoch nicht zuletzt durch einzelne dokumentierte und untersuchte Schadensfälle nachgewiesen. Ziel der vorliegenden Arbeit war es, die zur Verfügung stehenden Bauwerksuntersuchungen aus den zurückliegenden ca. 10 Jahren statistisch zu analysieren und auszuwerten. Auf dieser Basis war ein Berechnungsmodell wahrscheinlichkeitstheoretischer Basis zu entwickeln, mit dem die Gefahr eines spröden Bauwerksversagens für das Gesamttragwerk beurteilt und hinsichtlich der Auswirkungen auf das einzuhaltende Sicherheitsniveau bewertet werden kann. Es wurden insgesamt 31 Bauwerksuntersuchungen statistisch ausgewertet und beurteilt. Die zur Verfügung stehenden Daten wurden analysiert und hinsichtlich der Prüfqualität sowie der Quantität der Proben bewertet. Dabei war festzustellen, dass aufgrund fehlender konkreter Vorgaben im Regelwerk eine sehr heterogene Datenbasis vorliegt. Nicht alle Untersuchungsergebnisse konnten in die weitere Auswertung einbezogen werden. Die in ausreichender Datenqualität und Datenumfang geeigneten Untersuchungen wurden hinsichtlich ihrer Relevanz für den Prozess einer H-SpRK analysiert und die Auswirkungen einzelner Parameter bewertet. Im Ergebnis der materialtechnischen Untersuchungen und statistischen Auswertung der Bauwerksuntersuchungen wurde ein Berechnungsmodell vorgestellt, das den gleichzeitigen Ausfall von Spannstahl in allen Bereichen des Bauwerkes berücksichtigt. Zusätzlich zum Standardverfahren des beschriebenen Vorgehens wird das Modell um den Ansatz eines korrelierten Spannstahlausfalls erweitert. Außerdem wird für Bauwerke mit einem statisch unbestimmten Anteil der Vorspannung sowie für Konstruktionen mit gestaffelter Spannstahlbewehrung die Anwendung des Verfahrens konkretisiert. Neben der Erstellung des Berechnungsmodells wurden Vorschläge zu Vorgaben für die Bauwerksprüfung vorgestellt. Dazu zählen insbesondere die Festlegung von Prüfintervallen sowie einheitliche Vorgaben zu den verwendeten Prüfmethoden und -verfahren. Bezüglich der Festlegung von Mindestumfängen von Proben wird zwischen bestehenden und auch weiter zu nutzenden Bauwerken einerseits sowie Probennahmen im Rahmen von Rückbaumaßnahmen unterschieden.

Failure of carbon steel boiler tubes from waterside has been reported in the utility boilers and industrial boilers for a long time. In industrial boilers, most waterside tube cracks are found near heavy attachment welds on the outer surface and are typically blunt, with multiple bulbous features indicating a discontinuous growth. These types of tube failures are typically referred to as stress assisted corrosion (SAC). For recovery boilers in the pulp and paper industry, these failures are particularly important as any water leak inside the furnace can potentially lead to smelt-water explosion. Previous research shows that metal properties, environmental variables, and stress conditions are the major factors influencing SAC crack initiation and propagation in carbon steel boiler tubes. A significant volume of work has also been published to show that the use of carbon steel in high temperature water applications strongly depends upon the formation and stability of a protective magnetite oxide film on the waterside of boiler tubes. This present study is aimed at evaluating above stated variables individually and interactively to identify SAC crack initiation and crack propagation behavior in carbon steel boiler tubes. Other goal of this research is to understand the mechanism of bulbous SAC crack formation under industrial boiler operating conditions, thus to figure out a practical way to predict and prevent SAC type failures in the industrial boilers.

Primary water stress corrosion cracking (SCC) of metals in pressurized water reactors (PWRs) is known to be one of the most challenging and cost intensive modes of failure in the nuclear industry. Even though it is known that cracking in Ni-base alloys proceeds mainly intergranular (IG), the initiation and propagation of cracks in ductile metals are not yet understood and a much-desired accurate prediction of SCC related failure seems unobtainable. In this thesis, a combination of microcantilever fracture experiments, scanning electron- (SEM) and transmission electron microscopy (TEM) techniques was employed to study and compare the failure of oxidized grain boundaries of Ni-base Alloy 600 with high and low intergranular carbide coverage and different sample history. A new technique for lifting-out whole cantilevers after testing and for performing 3D focussed ion beam sequencing (3D FIB-SEM) while preserving a thin central region of the cantilever for further TEM sample preparation was developed and is presented. In lieu with recent efforts of the main project sponsor Électricité de France (EDF) to build a predictive model for IGSCC based on localized/microscopic information, one of the main objectives was the extraction of the stress at failure of individual oxidized GBs. Supported by finite element simulations, microcantilever fracture tests revealed that surface oxides on top of individual GBs have the capability to alter the mechanical response by delaying/suppressing the onset of failure. An overestimation of the failure stress (> 230 MPa) was observed, proving that the presence of the surface oxide on top of the test structures cannot be neglected. The failure stress on both samples, tested without influence of the surface oxide, was found to cover a range of 300 - 600 MPa, which agreed well with finite element simulations of the tests and further demonstrates the reliability of the obtained data. The second objective was to gain a better understanding of the observed fracture behaviour and the role of local microstructure. Using the gathered microscopy data, it was found that the crack clearly favours a progression along the IG oxide-metal interface in the presence of carbide precipitates. Electron energy loss spectroscopy (EELS) revealed that the observed crack path can be linked to compositional and density variations of the IG oxide. In the presence of carbides the oxide was layered. An oxide close to the stoichiometry of chromia was located at the original GB and next to the carbides. Next to this Cr-rich oxide, Fe-rich mixed spinel oxides of varying composition and density were found. An explanation for density variations based on the possible formation of defective spinel oxides of the type A²⁺B³⁺₂O₄, due to an unavailability of certain cation species is presented. No clear interface preference was observed in the absence of precipitation, where the IG oxide was found to be thin and often incomplete with Cr-richer oxides preferentially located at the original GB. While these observations were consistent on both samples (high and low carbide coverage), bigger void-like defects were located at the Fe-richer oxide-metal interface of the cold worked sample with high IG carbide precipitation only. These weak spots seemed to be the preferred path for crack propagation on this sample. The sample with low intergranular carbide coverage showed no obvious porosities at this interface but a Cr- depleted region was seen. Introducing a multi-faceted investigation strategy, supported by finite element simulations, the presented thesis provides the most accurate determination of the failure stress of oxidized GBs on Alloy 600 to date and and adds new valuable insights to our understanding of IGSCC and the future prediction of SCC related failures.

Um dos principais mecanismos de falha que causam riscos de fratura a reatores de água pressurizada é a corrosão sob tensão de ligas metálicas em água do circuito primário (CSTAP). É causada por uma combinação das tensões de tração, meio ambiente em temperatura e microestruturas metalúrgicas susceptíveis. Ela pode ocorrer, dentre outros locais, nos bocais do mecanismo de acionamento das barras de controle. Essa fratura pode causar acidentes que comprometem a segurança nuclear através do bloqueio das barras de controle e vazamentos de água do circuito primário reduzindo a confiabilidade e a vida útil do reator. O objetivo desta Tese de Doutorado é o estudo de modelos e uma proposta de modelagem para fraturas por corrosão sob tensão em liga 75Ni15Cr9Fe (liga 600), em água de circuito primário de reator de água pressurizada nesses bocais. São superpostos modelos eletroquímicos e de mecânica da fratura e validados com dados obtidos em experimentos e na literatura. Na parte experimental foram utilizados resultados obtidos pelo CDTN no equipamento recém-instalado de ensaio por taxa de deformação lenta. Na literatura está proposto um diagrama que exprime a condição termodinâmica de ocorrerem diversos modos de CSTAP na liga 600: partiu-se de diagramas de potencial x pH (diagramas de Pourbaix), para a liga 600 imersa em água primária à alta temperatura (3000C a 3500C). Sobre ele, determinaram-se os submodos de corrosão, a partir de dados experimentais. Em seguida acrescentou-se uma dimensão adicional ao diagrama, correlacionando uma variável a que se denominou fração de resistência à corrosão sob tensão. No entanto, é possível acrescentar-se outras variáveis que exprimem a cinética de iniciação e/ou crescimento de trinca, provenientes de outras modelagens de CSTAP. A contribuição original deste trabalho se insere nessa fase: partindo-se de uma condição de ensaio de potencial versus pH, foram iniciadas as modelagens de um modelo empírico-comparativo, um semi-empírico-probabilístico, um de tempo de iniciação e um de taxa de deformação, a partir dos ensaios experimentais e superpostas a essa condição. Esses exprimem respectivamente a susceptibilidade à CSTAP, o tempo de falha, e nos dois últimos o tempo de iniciação de falha por corrosão sob tensão. Os resultados foram comparados com os da literatura e se mostraram coerentes. Através desse trabalho, obteve-se uma metodologia de modelagem a partir de dados experimentais. / One of the main failure mechanisms that cause risks to pressurized water reactors is the primary water stress corrosion cracking (PWSCC) occurring in alloys. It can occurs, besides another places, at the control reactor displacement mechanism nozzles. It is caused by the joint effect of tensile stress, temperature, susceptible metallurgical microstructure and environmental conditions of the primary water. These cracks can cause accidents that reduce nuclear safety by blocking the rods displacement and may cause leakage of primary water, reducing the reactors life. In this work it is proposed a study of the existing models and a modeling proposal to primary water stress corrosion cracking in these nozzles in a nickelbased Alloy 600. It is been superposed electrochemical and fracture mechanics models, and validated using experimental and literature data. The experimental data were obtained at CDTN-Brazilian Nuclear Technology Development Center, in a recent installed slow strain rate testing equipment. In the literature it is found a diagram that indicates a thermodynamic condition for the occurrence of some PWSCC submodes in Alloy 600: it was used potential x pH diagrams (Pourbaix diagrams), for Alloy 600 in high temperature primary water (3000C till 3500C). Over it, were located the PWSCC submodes, using experimental data. It was added a third parameter called stress corrosion strength fraction. However, it is possible to superpose to this diagram, other parameters expressing PWSCC initiation or growth kinetics from other models. Here is the proposition of the original contribution of this work: from an original experimental condition of potencial versus pH, it was superposed, an empiric-comparative, a semi-empiric-probabilistic, an initiation time, and a strain rate damage models, to quantify respectively the PWSCC susceptibility, the failure time, and in the two lasts, the initiation time of stress corrosion cracking. It was modeling from our experimental data. The results were compared with the literature and it showed to be coherent. From this work was obtained a modeling methodology from experimental data.

No presente trabalho foi estudado o comportamento de um aço inoxidável austenítico do sistema Fe-Cr-Mn-N, nas condições como recebido, solubilizado e sensitizado, quando submetidos à meios contendo cloretos. Para analisar a suscetibilidade à corrosão sob tensão foram utilizados corpos de prova dos tipos DCB (\"Double Cantilever Beam\") e C(T) (\"Compact- Tension\"), pré-trincados em fadiga, com entalhes laterais e carregados com cunhas. Os meios empregados foram as soluções aquosas 45% em peso de MgCl2 na temperatura de ebulição de 154°C, água do mar sintética na temperatura ambiente e de ebulição de 100°C e 3,5% em peso de NaCI na temperatura ambiente. A suscetibilidade à corrosão sob tensão foi avaliada em termos do fator limite de intensidade de tensão, KISCC, e foram caracterizados os aspectos fractográficos dos corpos de prova em que ocorreram propagação de trinca por corrosão sob tensão. Foi verificado que apenas os corpos de prova do aço E3949 nas condições como recebido e sensitizado, foram suscetíveis à corrosão sob tensão em solução aquosa de 45% em peso de MgCl2 na temperatura de ebulição. Também foi determinado o comportamento eletroquímico do material nas condições citadas acima com relação aos meios empregados. Os resultados das curvas de polarização obtidas mostraram que o material apresenta baixa resistência à corrosão, principalmente em meios de MgCl2. / The present work studies the stress corrosion cracking behavior in austenitic Fe-Cr-Mn-N stainless steel, in as received, solubilized and sensitized conditions, when submited to several chlorides environments. To evalued the stress corrosion cracking susceptibility, DCB (\"Double Cantilcver Beam\") and C(T) (\"Compact- Tension\") specimens, fatigue precracked, side grooved and wedge loaded were used. The environments employed were boiling solution of 45 wt% of MgCl2 at 154ºC, synthetic sea water at room and 100°C temperatures, and a solution with 3,5 wt% of NaCI at room temperature. The susceptibility to stress corrosion cracking has been evaluated in terms of the threshold stress intensity factor, KISCC, and the fracture surface appearance of those specimens whose the crack propagation took place was characterized. The results showed that only the specimens in the as received and sensitized conditions, were suceptible to the stress corrosion cracking effect in the solution with 45 wt% of MgCl2 at the boilling temperature. Also, it has been verified the electrochemical behavior of this steel when submited in the above environments. The results of polarization curves showed that the material presents low corrosion strength, mainly in MgCl2 environments.

Les métaux déposés base nickel sont utilisés pour assembler des composants du circuit primaire des centrales nucléaires à Réacteurs à Eau sous Pression (REP). Un nombre croissant de cas de fissuration par Corrosion Sous Contrainte (CSC) des soudures en alliages base nickel 182 et 82 est rapporté dans le retour d'expérience international ce qui motive le développement d'un modèle permettant de prévoir la fissuration par CSC de ces matériaux. Ce mécanisme de dégradation fait intervenir des paramètres matériaux, mécaniques ou environnementaux qui peuvent interagir entre eux. L'objectif de cette étude est de mieux comprendre les mécanismes physiques locaux (aux joints de grains) impliqués dans l'amorçage de fissures de CSC. Un essai de traction sur une éprouvette en alliage 182 préalablement oxydée en milieu primaire simulé a mis en évidence une dispersion de la sensibilité à l'oxydation des différents joints de grains. L'analyse couplée entre oxydation et fissuration a permis, à l'aide de calculs de micro-mécanique sur un agrégat polycristallin synthétique, de proposer un critère de rupture des joints de grains oxydés défini par un couple profondeur d'oxydation/ contrainte locale critique. Compte tenu du rôle clé que tient l'oxydation intergranulaire dans le mécanisme de fissuration par CSC et de la dispersion observée entre les différents joints de grains, une cinétique d'oxydation intergranulaire des alliages base nickel 182 et 82 a été identifiée prenant en compte la précipitation de carbures de chrome, la température ou encore la teneur en hydrogène dissous. Ce modèle cinétique permet d'aborder statistiquement l'oxydation des joints de grains et est intégré à un modèle d'amorçage local. Dans ce dernier l'amorçage, défini par la fissuration de l'oxyde intergranulaire est suivi d'une phase de propagation lente puis rapide jusqu'à une certaine profondeur de fissure. Des hypothèses simplificatrices ont été faites lors de l'identification des lois embarquées dans le modèle de CSC. Toutefois, celles-ci s'avèreront utiles pour cibler les conditions des futurs essais à mener afin de conforter l'identification des différents paramètres. / Nickel base welds are widely used to assemble components of the primary circuit of Pressurized Water Reactors (PWR) plants. International experience shows an increasing number of Stress Corrosion Cracks (SCC) in nickel base welds 182 and 82 which motivates the development of models predicting the time to SCC initiation for these materials. SCC involves several parameters such as materials, mechanics or environment interacting together. The goal of this study is to have a better understanding of the physical mechanisms occurring at grains boundaries involved in SCC. In-situ tensile test carried out on oxidized alloy 182 evidenced dispersion in the susceptibility to corrosion of grain boundaries. Moreover, the correlation between oxidation and cracking coupled with micro-mechanical simulations on synthetic polycrystalline aggregate, allowed to propose a cracking criterion of oxidized grain boundaries which is defined by both critical oxidation depth and local stress level. Due to the key role of intergranular oxidation in SCC and since significant dispersion is observed between grain boundaries, oxidation tests were performed on alloys 182 and 82 in order to model the intergranular oxidation kinetics as a function of chromium carbides precipitation, temperature and dissolved hydrogen content. The model allows statistical analyses and is embedded in a local initiation model. In this model, SCC initiation is defined by the cracking of the intergranular oxide and is followed by slow and fast crack growth until the crack depth reaches a given value. Simplifying assumptions were necessary to identify laws used in the SCC model. However, these laws will be useful to determine experimental conditions of future investigations carried out to improve the calibration used parameters.