Poly[lactic co-glycolic] acid (PLGA) is a biocompatible polymer commonly used in the field of tissue engineering, but its mechanical properties tend to be less than ideal for most orthopedic applications. Five PLGA composites, reinforced with 0 to 1% nonfunctionalized single-walled carbon nanotubes, were prepared and tested for tensile strength. In order to achieve consistent nanotube dispersions, sodium dodecyl sulfate was incorporated as a surfactant. The polymer scaffold fabrication methods were successful at creating suitable samples for tensile testing. After the tests were performed, scanning electron microscope images were taken to examine the fractured edges and determine the cause of failure. Analysis of fractured surfaces indicated good nanotube dispersions in all composite samples, and an increase in tensile strength, with respect to the control (0.532 MPa), was found for composites at the 0.07% nanotube and 0.09% nanotube concentrations (0.570 MPa and 0.643 MPa respectively). Total length at failure decreased as carbon nanotube concentration increased. This experiment showed a promising trend toward increasing the mechanical properties of PLGA/carbon nanotube composites and represented a prospective foundation for future research.

This study employs the Modified Embedded Atom Method with Bond Order (MEAM-BO) atomic potential as first used to capture single-wall carbon nanotube (SWCNT) properties accurately. We updated the MEAM-BO potential parameters to produce a MEAM-BO* potential for the SWCNT system. Calculating the wavenumber of the radial breathing mode (RBM), elastic properties, and folding energy (DELTA E) of SWCNT which are all associated with bond curvature was considered. Interestingly, MEAM-BO* including the SWCNT data base, improved the previous fit of the C-H system. Further discussed is how we constructed five different partially unzipped carbon nanotubes (PUCNT) and investigate the mechanical properties and self-healing of the simplest PUCNT by using molecular dynamics simulations. In addition, we studied the exploration of damage evolution and the mechanical response of a polyethylene/single wall carbon nanotube composite (SWCNT-PE) at different stress states, temperatures, and strain rates which are studied through utilizing atomistic simulations. The SWCNT-PE composite was expanded perpendicular to the nanotube direction and damage was computed in terms of the void number density (void nucleation) and void volume

No description available.

Submitted by Renata Lopes (renatasil82@gmail.com) on 2017-06-02T14:11:01Z No. of bitstreams: 1 arthurbarraporto.pdf: 4422124 bytes, checksum: 6ea016d6bb89f506c7e2ee4f2fdc7a24 (MD5) / Approved for entry into archive by Adriana Oliveira (adriana.oliveira@ufjf.edu.br) on 2017-06-06T12:08:10Z (GMT) No. of bitstreams: 1 arthurbarraporto.pdf: 4422124 bytes, checksum: 6ea016d6bb89f506c7e2ee4f2fdc7a24 (MD5) / Made available in DSpace on 2017-06-06T12:08:10Z (GMT). No. of bitstreams: 1 arthurbarraporto.pdf: 4422124 bytes, checksum: 6ea016d6bb89f506c7e2ee4f2fdc7a24 (MD5) Previous issue date: 2017-03-31 / O tratamento químico de nanotubos de carbono (NTC) é necessário para aprimorar suas propriedades, aplicações e remover impurezas. O tratamento, com ácidos fortes como H2SO4 e HNO3 tem sido a alternativa mais utilizada. A mistura desses ácidos fortes produz espécies eletrofílica NO2+, íon nitrônio, que é um potencial agente oxidante, cuja concentração depende da proporção da mistura H2SO4:HNO3. Neste trabalho, a interação entre o íon nitrônio e o nanotubo de carbono de camada única (SWCNT, do inglês Single-Walled Carbon Nanotube) foi explorado experimental e computacionalmente. Experimentalmente a solução H2SO4:HNO3 foi analisada em proporções diferentes (1:1, 2:1, 5:2, 3:1, 4:1, 5:1, 6:1, 7:1 e 8:1 v/v) e a concentração de íon nitrônio foi obtida utilizando-se uma curva analítica construída com uma solução padrão de NO2BF4 em H2SO4. Todas as espécies na mistura ácida foram caracterizadas por espectroscopia Raman. Os resultados mostraram que a concentração do íon nitrônio na mistura ácida varia de 0 até 4,53 mol/L. As misturas 2:1, 5:2 e 3:1 foram então utilizadas para a oxidação química de SWCNT por 4, 8 e 12 horas. As amostras finais foram analisadas por espectroscopia Raman, análise termogravimétrica (TG) e espectroscopia de raios X por dispersão de energia (EDS). Dentre os resultados, foram observados por meio da espectroscopia Raman uma alta desordem estrutural no sistema após a oxidação, com significativas mudanças nos modos de respiração radial (RBM), como o desaparecimento de bandas de tubos com pequenos diâmetros, além do aumento dada razão ID/IG de 0,027 para 0,59 em tubos oxidados com a mistura 3:1. As análises TG mostraram um aumento na temperatura de decomposição dos tubos em, pelo menos, 30ºC se comparado às amostras padrão, sugerindo um significativo grau de oxidação. Os resultados de EDS apontaram um aumento considerável na quantidade de oxigênio, passando de 7% para 20%, aumentando com o aumento do tempo de reação e com a concentração do íon nitrônio. Computacionalmente a interação entre o íon nitrônio e o SWCNT foi estudada através de cálculos de mecânica quântica. Foram analisados modelos do tipo armchair (5,5), sendo um tubo perfeito (P) e dois outros contendo defeitos do tipo Stone-Wales (SW) e monovacância (V1) para modelar regiões distintas na superfície do nanotubo. Para os modelos P e SW, o grupo funcional éter (COC) foi obtido como um produto principal, com um epóxido (CCO) encontrado como um intermediário de reação. As barreiras de energia livre de Gibbs foram de 31,7 kcal.mol-1 (P) e 37,8 kcal.mol-1 (SW) em solução aquosa à 298,15 K e 1 atm. O mecanismo envolvendo o modelo V leva à obtenção de uma carbonila (CO) como produto principal, formado espontaneamente através da adsorção do íon NO2+. O mecanismo de alta energia também foi descrito no modelo V, passando por um estado de transição, caracterizado como um anel do tipo oxaziridina. Através deste caminho um grupamento do tipo alcóxido (CO-) é formado inicialmente e reage com um carbono vizinho, produzindo um grupo funcional do tipo éter (COC). A energia livre de Gibbs de ativação foi de 4,5 e 11,2 kcal.mol-1 para primeiro (CO-) e segundo (COC) passos, respectivamente. Os resultados reportados sugerem o início da oxidação em meio ácido através da região de vacância, com primeira oxidação levando a uma carbonila, seguida das reações nos defeitos topológicos (P e SW) na superfície com a formação de um éter (COC) como principal produto. / The chemical treatment of carbon nanotubes (CNT) is necessary to improve their properties, applications and to remove impurities. Treatments with strong acids as H2SO4 and HNO3 is the mostly used alternative. The mixture of these strong acids produces the electrophilic species NO2+, the nitronium ion that is a potential oxidizing with concentration depending on the H2SO4:HNO3 proportion. In this work the interaction between the nitronium ion and a single-walled carbon nanotube (SWCNT) was explored experimentally e theoretically. Experimentally, the H2SO4:HNO3 solution was analyzed at different proportions (1:1, 2:1, 5:2, 3:1, 4:1, 5:1, 6:1, 7:1 and 8:1 v/v) and the nitronium ion concentration obtained using a calibration plot constructed from a standard solution of NO2BF4 in H2SO4. All the species in the acid mixture were characterized by Raman spectroscopy. The results showed that the concentration of nitronium ion in the acid mixtures varied from 0 to 4.53 mol/L. The mixtures 2:1, 5:2 and 3:1 were then used for the chemical oxidation of single-walled CNT for 4, 8 and 12 hours. The final samples were analyzed by Raman spectroscopy, thermal gravimetric analysis (TGA) and energy dispersive X-ray spectroscopy (EDS). It was observed by Raman spectroscopy a higher structural disorder in the system after the oxidation, with significant changes in RBM modes, such as disappearance of bands of small diameter tubes, and in the ID/IG ratio, which increases from 0.027 until 0.59 to CNT oxidized with 3:1 mixture. The TGA showed an increase in the temperature of the tube decomposition of at least 30ºC relative to the pristine form, suggesting a significant oxidation degree. The EDS data point to considerable increase of the oxygen amount from 7% to at least 20%, increasing with the reaction time and nitronium ion concentration. Theoretically the interaction between nitronium ion and SWCNT was studied by quantum mechanical calculations. In addition to the pristine (P) form of an armchair (5,5) SWCNT, two other species containing Stone-Wales (SW) and mono-vacancy (V1) defects were considered in order to model the distinct defective regions on the carbon nanotube surface. For the P and SW regions, the ether (COC) functional group was predicted as the main product, with an epoxide (CCO) found as a reactive intermediate. The Gibbs free energy barriers were predicted to be 31.7 (P) and 37.8 kcal mol-1 (SW) in aqueous solution at 298.15 K and 1 atm. The mechanism involving the V1 region leads to the carbonyl group (CO) as the main product, which is formed spontaneously upon NO2+ adsorption without energy barrier. A higher energy mechanism was also described for V1 region, passing through a transition state characterized as an oxaziridine-like ring. Through this pathway an alkoxy (CO-) is firstly formed and reacts with the neighbor carbon yielding the ether (COC) functional group. The activation Gibbs free energies were 4.5 and 11.2 kcal mol-1 for the first (CO- formation) and second (COC formation) steps, respectively. The results reported here suggest that at the beginning of oxidation in acid medium, the vacancy regions (V) are firstly oxidized leading to the carbonyl (CO) functional groups, followed by reactions at the topological defective parts (P and SW) of the tube surface where the ether (COC) function is the main product.

L’objectif final de la thèse est l'impression de la couche photo-active ternaire d'une cellule solaire organique en utilisant deux approches: l'une concerne l'apport de nanotubes de carbone (SWCNT) pour améliorer les propriétés de transport, l'autre concerne la préparation de mélanges ternaires de matériaux pour contrôler la couleur des cellules. Les encres pour la couche active incluant des SWCNT fonctionnalisés sont composées d’un donneur d'électron (polymère) (poly(3-hexylthiophène), [P3HT]) et d’un accepteur d'électron ( [6,6]-phényl C61-butyrique ester méthylique d'acide [PCBM]) et ont été développées pour la fabrication de cellules inversées. Ces cellules sont réalisées sur substrats de verre pour l'optimisation de leurs performances, puis sur substrats plastiques pour les applications. Diverses couches d'interfaces ont été testées, qui incluent l'oxyde de zinc (ZnO, couches obtenues par pulvérisation ionique (IBS) ou à partir de solutions de nanoparticules) pour la couche de transport d'électrons et le PEDOT:PSS, le P3MEET, le V2O5 et le MoO3 pour la couche de transport de trous. Des essais ont été effectués avec et sans CNT afin d’étudier leur impact sur les performances. Des résultats similaires sont obtenus dans les deux cas. Il était attendu que les CNT améliorent les performances, ce qui n’a pas été observé pour le moment. Des travaux supplémentaires sont donc nécessaires au niveau de la formulation de la couche active.Avec trois polymères de couleur rouge (P3HT), bleu (B1) et vert (G1), nous avons préparé des mélanges ternaires efficaces permettant l'obtention de couleurs jusque là indisponibles . Nous avons fait une étude sur le piégeage et les mécanismes de diodes parallèles associés aux mélanges. En général, nous avons constaté que les mélanges ternaires de polymères bleu et vert peuvent être décrits par une mécanisme de diodes parallèles, sans entrainer de perte de performances, ce qui n'est pas possible pour les systèmes P3HT:B1 :PCBM et P3HT:G1:PCBM qui se piègent mutuellement. L’objectif final du projet est l'impression de la couche photo-active ternaire d'une cellule solaire organique, composites ternaires (polymère:polymères:acceptor) ou dopés avec les SWCNT. Cette étape nécessite encore des développements futurs. / Two approaches were followed to achieve increased control over properties of the photo-active layer (PAL) in solution processed polymer solar cells. This was accomplished by either (1) the addition of functionalized single-walled carbon nanotubes (SWCNTs) to improve the charge transport properties of the device or (2) the realization of dual donor polymer ternary blends to achieve colour-tuned devices.In the first component of the study, P3HT:PC61BM blends were doped with SWCNTs with the ambition to improve the morphology and charge transport within the PAL. The SWCNTs were functionalized with alkyl chains to increase their dispersive properties in solution, increase their interaction with the P3HT polymer matrix, and to disrupt the metallic characteristic of the tubes, which ensures that the incorporated SWCNTs are primarily semi-conducting. P3HT:PCBM:CNT composite films were characterized and prepared for use as the photoactive layer within the inverted solar cell. The CNT doping acts to increase order within the active layer and improve the active layer’s charge transport properties (conductivity) as well as showed some promise to increase the stability of the device. The goal is that improved charge transport will allow high level PSC performance as the active layer thickness and area is increased, which is an important consideration for large-area inkjet printing. The use of ternary blends (two donor polymers with a fullerene acceptor) in bulk-heterojunction (BHJ) photovoltaic devices was investigated as a future means to colour-tune ink-jet printed PSCs. The study involved the blending of two of the three chosen donor polymers [red (P3HT), blue (B1), and green (G1)] with PC61BM. Through EQE measurements, it was shown that even devices with blends exhibiting poor efficiencies, caused by traps, both polymers contributed to the PV effect. However, traps were avoided to create a parallel-like BHJ when two polymers were chosen with suitable physical compatibility (harmonious solid state mixing), and appropriate HOMO-HOMO energy band alignment. The parallel diode model was used to describe the PV circuit of devices with the B1:G1:PC61BM ternary blend.

Single-walled carbon nanotubes (SWCNTs) are new forms of carbon nanostructure that have exhibited important physical and chemical properties with a wide range of future applications including microelectronic devices, nanoscale transistors, catalyst supports, biosensors, reinforcement materials, medical chemistry, etc. Up to now, many versatile methods have been used for SWNCT synthesis. These methods can produce SWCNT besides many by-products such as amorphous carbon, fullerenes, nanocrystalline graphite and multi-walled carbon nanotubes. For the exploration of the physical properties of SWNCT and to investigate the possibilities of chemical functionalization it is advantageous to work with a material that is as pure as possible. The work presented here is focused on in situ purification of SWCNT soot synthesized by a large-scale (i.e., production rate of ~100 g h[superscript -1]) induction thermal plasma process. The main objectives of this research are: 1) to get rid of amorphous carbon impurities from SWCNT soot produced in the induction thermal plasma system, 2) to study the effect of oxidizing gas flow rate (i.e. oxygen) and temperature on the purification process. The methodology used in this experimental design is based on gas-phase thermal oxidation of synthesized SWCNT soot. The experimental apparatus can be divided in to two parts as follows: 1) synthesis system which consists of a flow type reactor equipped with a high frequency plasma torch operated at 3 MHz along with quenching and filtration systems 2) purification system which consists of an oven and a gas heater used to control the temperature of oxidizing gases, and a filtration system where thermal oxidation of the synthesized soot takes place. SWCNT soot was synthesized by an induction thermal plasma process using a mixture of carbon black (Raven 860 ultra) as a carbon source and nickel (Ni), cobalt (Co) and yttrium oxide (Y[subscript 2]O[subscript 3]) as catalysts. A series of preliminary experimental tests was conducted to evaluate the process ability to purify SWCNT soot in situ using a gas-phase thermal oxidation process. In these tests, temperature measurements along the filtration system were carried out during synthesis and purification processes. Two types of oxidizing gases (i.e., air and oxygen) were injected into the filtration system and the purified samples were characterized by different powerful techniques such as high resolution scanning electron microscopy (HRSEM), transmission electron microscopy (TEM), thermo-gravimetric analysis (TGA) and Raman spectroscopy. The results indicated that in situ removal of amorphous carbon from SWCNT soot synthesized by induction thermal plasma can be successfully achieved (a purity of more than 60 wt% of SWCNTs was achieved). Moreover thermal oxidation of the soot causes a narrower distribution of tube diameters in the purified sample. Overall, the findings of this study are relevant to the purification process technology of SWCNTs and future research is proposed to fully understand the reaction mechanism of SWCNT soot by oxygen. Based in the results of this work, additional work using a modification of the filtration system (i.e., collection chamber and filter tubes) should be performed in order to get rid of other carbonaceous impurities. Different gases can be also introduced in to the filtration system to improved the purification process and extend it for removal of catalysts particles. Our findings reveal that the present synthesis system has a capability for functionalization of tubes in situ. Therefore according to the type of functional groups which are desired to be attached to the tubes, proper gases can be injected into the filtration system.

This dissertation involves the study of epitaxial behavior of one-dimensional nanomaterials like single-walled carbon nanotubes and Indium Arsenide nanowires grown on metallic catalyst surfaces. It has been previously observed in our novel microplasma based CVD growth of SWCNTs on Ni-Fe bimetallic nanoparticles that changes in the metal catalyst composition was accompanied by variations in the average metal-metal bond lengths of the nanoparticle and that in turn, affected nanotube chirality distributions. In this dissertation, we have developed a very simplistic model of the metal catalyst in order to explain the nanotube growth of specific nanotube chiralities on various Ni-Fe catalyst surfaces. The metal catalyst model is a two-dimensional flat surface with varying metal-metal bond lengths and comprising of constituent metal atoms. The effect of the composition change was modeled as a change in the bond length of the model catalyst surface and density functional theory based calculations were used to study specific nanotube caps. Our results indicated that nanotube caps like (8,4) and (6,5) show enhanced binding with increased metal-metal bond lengths in the nanoparticle in excellent agreement with the experimental observations. Later, we used this epitaxial nucleation model and combined with a previously proposed chirality-dependent growth rate model to explore better catalysts that will preferentially grow an enhanced chirality distribution of metallic nanotubes. From our DFT calculations and other geometrical considerations for nanotube growth, we demonstrated that the pure Ni0.5Cu0.5 metal nanoparticles and its lattice-strained surfaces can serve as a promising catalyst for enhanced growth of metallic nanotubes. Finally, we extended this model of epitaxial growth to study the growth of,andoriented nanowires on gold metal nanoparticles where a faster growth rate ofnanowires was previously observed in experiments on shaped nanoparticles than that on spherical nanoparticles. The DFT calculations indicated an enhanced growth selectivity of theoriented nanowires on the Au(111) surfaces. However, the DFT results also show that theandNWs will preferentially grow on the Au(100) surface than on the Au(100) surface. The epitaxial model based DFT calculations of nanotube and nanowire growth on metal catalyst surfaces presented in this dissertation, provide a deep insight into their epitaxial growth mechansims and, can be easily exploited to layout better design principles of synthesizing catalysts that helps in growing these one-dimensional nanomaterials with desired material properties.

Well dispersed aqueous suspensions containing single-walled carbon nanotubes (SWCNTs) from bulk powders were prepared with surfactant and without surfactant by acid functionalization. SWCNT coated electrodes were then prepared from the SWCNT aqueous suspensions using various methods to create uniform nanoporous networks of SWCNTs on various substrates and stainless steel (SST) current collectors for use as ultracapacitor electrodes. Drop coating, high voltage electro-spraying (HVES), inkjet printing, and electrophoretic deposition (EPD) methods were evaluated. Optical and scanning electron microscope images were used to evaluate the SWCNT dispersion quality of the various electrodes. Ultimately an EPD process was established which reliably produced uniform SWCNT nanoporous networks on SST substrates. The prepared SWCNT coated electrodes were characterized using cyclic voltammetry and their capacitance was determined. A correlation between extended EPD processing times, EPD processing temperatures, and electrode capacitance was quantified. Optimum EPD processing occurs where linear capacitance gains were observed for processing times less than 10 minutes. At processing times between 10 – 60 minutes a non-linear relationship demonstrated diminishing capacitance gains with extended EPD processing times. Likewise, optimum EPD processing occurs when the processing temperature of the SWCNT suspension is raised above room temperature. At processing temperatures from 45°C to 60°C an increase in capacitance was observed over the room temperature (22°C) electrodes processed for the same durations. Conversely, for processing temperatures less than room temperature, at 5°C, a decrease in capacitance was observed. It was also observed that SWCNT electrodes processed at 60°C processing temperatures resulted in 4 times the capacitance of 5°C electrodes for the same processing times, when the durations were 8 minutes or less. For samples with raised processing temperatures the time dependent capacitance gains were observed to be significantly diminished beyond 10 minute processing times. The SWCNT network thickness was also correlated to EPD processing temperature and capacitance. A linear relationship was identified between the SWCNT network thickness and the capacitance of the electrode. It was also observed that elevated processing temperatures increase the EPD deposition rate of SWCNTs, produce thicker SWCNT networks, and thus create electrodes with higher capacitance than electrodes processed at lower EPD processing temperatures. EPD of SWCNTs was demonstrated in this work to be an effective method for the fabrication of SWCNT ultracapacitor electrodes. Characterization of the process determined that optimal EPD processing occurs within the first 10 minutes of processing time and that elevated processing temperatures yield higher SWCNT deposition rates and higher capacitance values. In this work the addition of SWCNT nanoporous networks to SST electrodes resulted in increases in capacitance of up to 398 times the capacitance of the uncoated SST electrodes yielding a single 1cm2 electrode with a capacitance of 91mF and representing an estimated specific capacitance for the processed SWCNT material of 45.78F/g.

The extraordinary properties of the single wall carbon nanotubes (SWCNTs) have stimulated an enormous amount of research towards the realization of SWCNT-based products for different applications ranging form nanocomposites to nanoelectronics. Their high charge mobility, exceedingly good current-carrying capacities and ability to be either semiconducting or metallic render them ideal building blocks for nanoelectronics. For nanoelectronic applications, either individual or parallel aligned SWCNTs are advantageous. Moreover, closely packed arrays of parallel SWCNTs are required in order to sustain the relatively large currents found in high frequency devices. Two key areas still require further development before the realization of large-scale nanoelectronics. They are the reproducible control of the nanotubes spatial position/orientation and chiral management. In terms of nanotube orientation, different techniques have been demonstrated for the fabrication of horizontally aligned SWCNTs with either post synthesis routes (e.g. dielectrophoresis and Langmuir-Blodgett approach) or direct growth (e.g. chemical vapor deposition (CVD)). The low temperature of the production process, allowing the formation of aligned nanotubes on pretty much any substrate, is the main advantage of the post synthesis routes, while the poor levels of reproducibility and spatial control, and the limited quality of the aligned tubes due to the inherently required process steps are limitations. The simplicity, up-scalability, along with the reproducible growth of clean high quality SWCNTs with well-controlled spatial, orientation and length, make CVD the most promising for producing dense horizontally well-aligned SWCNTs. These CVD techniques suffer some drawbacks, namely, that because they are synthesized using catalyst particles (metals or non-metals) the catalyst material can contaminate the tubes and affect their intrinsic properties. Thus, the catalyst-free synthesis of aligned SWNT is very desirable. This thesis comprises detailed and systematic experimental investigations in to the fabrication of horizontally aligned SWCNTs using both post growth (Dielectrophoresis) and direct growth (CVD) methods. Both catalyst-assisted and catalyst-free SWCNTs are synthesized by CVD. While metallic nanoparticles nucleate and grow SWCNTs, opened and activated fullerene structures are used for all carbon catalyst-free growth of single wall and double wall carbon nanotubes. The systematic studies allow for a detailed understanding of the growth mechanisms of catalyst and catalyst-free grown SWCNTs to be elucidated. The data significantly advances our understanding of horizontally aligned carbon nanotubes by both post synthesis alignment as well as directly as-synthesized routes. Indeed, the knowledge enables such tubes to be grown in high yield and with a high degree of special control. It is shown, for the first time, how one can grow horizontally aligned carbon nanotubes in crossbar configurations in a single step and with bespoke crossing angles. In addition, the transport properties of the aligned tubes at room temperature are also investigated through the fabrication of devices based on these tubes. / Die außergewöhnlichen Eigenschaften von einwandigen Kohlenstoffnanoröhren (engl. single wall carbon nanotubes, SWCNTs) haben bemerkenswerte Forschungsaktivitäten zur Verwirklichung von auf SWCNTs basierenden Anwendungen für verschiedene Bereiche, die von Nanokompositen bis hin zur Nanoelektronik reichen, stimuliert. Ihre hohe Ladungsträgermobilität und die außerordentlichen hohen Ladungsdichten, die in SWCNTs erreicht werden können sowie ihre Eigenschaft, entweder halbleitend oder metallisch zu sein, machen sie zu idealen Konstituenten von nanoelektronischen Schaltkreisen. Für Anwendungen in der Nanoelektronik sind entweder einzelne oder parallel angeordnete SWCNTs vorteilhaft. Darüber hinaus sind dicht gepackte Anordnungen von SWCNTs erforderlich, um die relativ hohen Ströme in Hochfrequenzbauelementen zu transportieren. Für eine erfolgreiche Realisierung von großskaligen nanoelektronischen Bauteilen, die auf SWCNTs basieren, sind noch zwei enorm wichtige Kernprobleme zu lösen, die weitere Forschungsanstrengungen erfordern: die reproduzierbare und verlässliche Kontrolle der räumlichen Positionierung und Orientierung der Nanoröhren sowie die Kontrolle der Chiralität der einzelnen SWCNTs. Hinsichtlich der Orientierung der Nanoröhren kann die horizontal parallele Ausrichtung von SWCNTs mit verschiedenen Techniken erreicht werden. Diese setzen entweder nach dem eigentlichen Wachstum der Röhren ein (Post-Synthese-Methoden wie z.B. Dielektrophorese oder Langmuir-Blodgett-Techniken) oder erreichen direkt während des Wachstums (z.B. durch Chemical-Vapor-Deposition-Methoden (CVD)) die parallele Anordnung. Durch die niedrigen Prozesstemperaturen, die während des Herstellungsprozesses erforderlich sind, erlauben die nach der eigentlichen Synthese stattfindenden Ausrichtungsmethoden die parallele Anordnung von Nanoröhren auf nahezu jedem Substrat, jedoch stellen die geringe Reproduzierbarkeit dieser Prozesse, die schwierige Kontrollierbarkeit der räumlichen Anordnung und die limitierte Qualität der ausgerichteten Röhren aufgrund der erforderlichen Prozessschritte natürliche Beschränkungen dieser Techniken dar. Die einfache Durchführung und ihre Skalierbarkeit, zusammen mit dem reproduzierbaren Wachstum qualitativ sehr hochwertiger SWCNTs mit hoher Kontrolle von räumlicher Anordnung, Orientierung und Länge machen die CVD-Methode zur erfolgversprechendsten Technik für die Herstellung von dichtgepackten hochparallelen horizontalen Anordnungen von SWCNTs. Diese CVD-Ansätze weisen jedoch auch einige Nachteile auf, die in den bei der Synthese verwendeten Katalysatorpartikeln (metallisch oder nicht-metallisch) begründet liegen, da das Katalysatormaterial die Röhren kontaminieren und dadurch ihre intrinsischen Eigenschaften beeinflussen kann. Daher ist eine katalysatorfreie Synthesemethode für ausgerichtete SWCNTs ein höchst erstrebenswertes Ziel. Die vorliegende Arbeit beschreibt detaillierte und systematische experimentelle Untersuchungen zur Herstellung von horizontalen, parallel ausgerichteten Anordnungen von SWCNTs unter Verwendung von Methoden, die sowohl nach dem eigentlichen Wachstum der Nanoröhren (Dielektrophorese) als auch während des Wachstums ansetzen (CVD). Bei den CVD-Methoden werden sowohl solche, die auf der Verwendung von Katalysatoren basieren, als auch katalysatorfreie Techniken verwendet. Während metallische Nanopartikel den Ausgangspunkt für das Wachstum von SWCNTs darstellen, werden geöffnete und aktivierte Fullerenstrukturen verwendet, um das katalysatorfreie Wachstum von reinen ein- oder mehrwandigen Nanoröhren zu erreichen. Die systematischen Untersuchungen ermöglichen ein tiefgehendes Verständnis der Wachstumsmechanismen von SWCNTs, die unter Verwendung von Katalysatoren oder katalysatorfrei erzeugt synthetisiert wurden. Die erzielten Ergebnisse erhöhen in einem hohen Maß das Verständnis der Herstellung von horizontal parallel angeordneten Nanoröhren, die durch Post-Synthese-Methoden oder direkt während des Wachstumsprozesses ausgerichtet wurden. Die erzielten Einsichten erlauben die Herstellung solcher Strukturen mit hoher Ausbeute und mit einem hohen Maß an räumlicher Kontrolle der Anordnung. Zum ersten Male kann ein Verfahren präsentiert werden, mit dem horizontal parallel angeordnete Nanoröhren in gekreuzten Strukturen mit wohldefinierten Kreuzungswinkeln hergestellt werden können. Zusätzlich werden die Transporteigenschaften von parallel ausgerichteten Nanoröhren bei Raumtemperatur, durch die Herstellung von auf den dargestellten Strukturen basierenden Bauelementen, untersucht.

Well dispersed aqueous suspensions containing single-walled carbon nanotubes (SWCNTs) from bulk powders were prepared with surfactant and without surfactant by acid functionalization. SWCNT coated electrodes were then prepared from the SWCNT aqueous suspensions using various methods to create uniform nanoporous networks of SWCNTs on various substrates and stainless steel (SST) current collectors for use as ultracapacitor electrodes. Drop coating, high voltage electro-spraying (HVES), inkjet printing, and electrophoretic deposition (EPD) methods were evaluated. Optical and scanning electron microscope images were used to evaluate the SWCNT dispersion quality of the various electrodes. Ultimately an EPD process was established which reliably produced uniform SWCNT nanoporous networks on SST substrates. The prepared SWCNT coated electrodes were characterized using cyclic voltammetry and their capacitance was determined. A correlation between extended EPD processing times, EPD processing temperatures, and electrode capacitance was quantified. Optimum EPD processing occurs where linear capacitance gains were observed for processing times less than 10 minutes. At processing times between 10 – 60 minutes a non-linear relationship demonstrated diminishing capacitance gains with extended EPD processing times. Likewise, optimum EPD processing occurs when the processing temperature of the SWCNT suspension is raised above room temperature. At processing temperatures from 45°C to 60°C an increase in capacitance was observed over the room temperature (22°C) electrodes processed for the same durations. Conversely, for processing temperatures less than room temperature, at 5°C, a decrease in capacitance was observed. It was also observed that SWCNT electrodes processed at 60°C processing temperatures resulted in 4 times the capacitance of 5°C electrodes for the same processing times, when the durations were 8 minutes or less. For samples with raised processing temperatures the time dependent capacitance gains were observed to be significantly diminished beyond 10 minute processing times. The SWCNT network thickness was also correlated to EPD processing temperature and capacitance. A linear relationship was identified between the SWCNT network thickness and the capacitance of the electrode. It was also observed that elevated processing temperatures increase the EPD deposition rate of SWCNTs, produce thicker SWCNT networks, and thus create electrodes with higher capacitance than electrodes processed at lower EPD processing temperatures. EPD of SWCNTs was demonstrated in this work to be an effective method for the fabrication of SWCNT ultracapacitor electrodes. Characterization of the process determined that optimal EPD processing occurs within the first 10 minutes of processing time and that elevated processing temperatures yield higher SWCNT deposition rates and higher capacitance values. In this work the addition of SWCNT nanoporous networks to SST electrodes resulted in increases in capacitance of up to 398 times the capacitance of the uncoated SST electrodes yielding a single 1cm2 electrode with a capacitance of 91mF and representing an estimated specific capacitance for the processed SWCNT material of 45.78F/g.