Introduction: Though xenogeneic acellular scaffolds are frequently used for surgical reconstruction, knowledge of their mechanical properties is lacking. This study compared the mechanical, histological and ultrastructural properties of various native and acellular specimens. Materials and methods: Porcine esophagi, ureters and skin were tested mechanically in a native or acellular condition, focusing on the elastic modulus, ultimate tensile stress and maximum strain. The testing protocol for soft tissues was standardized, including the adaption of the tissue’s water content and partial plastination to minimize material slippage as well as templates for normed sample dimensions and precise cross-section measurements. The native and acellular tissues were compared at the microscopic and ultrastructural level with a focus on type I collagens. Results: Increased elastic modulus and ultimate tensile stress values were quantified in acellular esophagi and ureters compared to the native condition. In contrast, these values were strongly decreased in the skin after acellularization. Acellularization-related decreases in maximum strain were found in all tissues. Type I collagens were well-preserved in these samples; however, clotting and a loss of cross-linking type I collagens was observed ultrastructurally. Elastins and fibronectins were preserved in the esophagi and ureters. A loss of the epidermal layer and decreased fibronectin content was present in the skin. Discussion: Acellularization induces changes in the tensile properties of soft tissues. Some of these changes appear to be organ specific. Loss of cross-linking type I collagen may indicate increased mechanical strength due to decreasing transverse forces acting upon the scaffolds, whereas fibronectin loss may be related to decreased load-bearing capacity. Potentially, the alterations in tissue mechanics are linked to organ function and to the interplay of cells and the extracellular matrix, which is different in hollow organs when compared to skin.

This diploma thesis focused on manufacturing and characterization of Ti-15Mo metastable beta-Ti alloy prepared by cryogenic milling and spark plasma sintering. Initial powder was prepared by gas atomization and consequently deformed by cryogenic milling (milled powder). Both initial and milled powders were compacted by spark plasma sintering (SPS) at temperatures from 750 řC to 850 řC. Dependence of microstructure and mechanical properties on the parameters of preparation was studied. During cryo-milling, powder particles significantly changed shape from ball-shaped to disc-shaped. Particles were not refined by milling, but severely plastically deformed. SEM observations showed that all prepared samples contain duplex alpha + beta structure. Volume fraction of alpha phase is significantly higher in the sintered milled powder due to increased beta- transus temperature caused by contamination by oxygen and also due to easier alpha phase precipitation caused by refined microstructure. Maximum microhardness of 350 HV was achieved for both types of sintered powders. High microhardness of sintered initial powder can be attributed to formation of omega phase during cooling, while sintered milled powder is strengthened by refined microstructure and small alpha phase precipitates. Cryogenic milling prior to...

>Magister Scientiae - MSc / Hydrogen has high energy density and it is regarded as the future energy carrier. Hydrogen can be stored as a gas in high-pressure cylinders, as a liquid in cryogenic tanks and as a solid in metal hydrides. The storage of hydrogen in gas and liquid form has many limitations. Light metal hydrides show high energy density and are a promising and more practical mode of hydrogen storage. In particular, titanium and its alloys are promising metal hydrides for hydrogen storage due to their high affinity to hydrogen. The aim of this study is to investigate the effect of thermal annealing on hydrogen storage capacity of Ti-Pd multilayer systems. Ti-Pd multilayer films were prepared on CP-Ti (commercial pure Ti) and Ti6Al4V substrates using an electron beam evaporator equipped with a thickness monitor. The sequential deposition of layers Pd(50nm)/Ti(25nm)/Pd(50nm) was done at a constant deposition rate of 0.6 Å/s. The first batch of samples were thermally annealed at 550 °C in vacuum for two hours, the second batch of samples were annealed at 550 oC under H2(15%)/Ar(85%) gas mixture for two hours and the third series of samples was annealed under pure H2 gas at 550 oC for one hour. SEM showed relatively homogeneous and smooth topography of surfaces in as-deposited samples, while a rough textured surface was observed in both samples annealed under vacuum and under H2/Ar gas mixture. The samples annealed under pure H2 gas did not show any sign of crystallites grow but instead a relatively smooth surface with sign of etching. XRD revealed structural transformation as evidenced by the presence of PdTi2 phase in samples annealed under vacuum; in samples annealed under the gas mixture Pd2Ti was noted in addition to TiH2 and TiO2. While the TiH2 phase is an indication of hydrogen absorption, the TiPd2 phase suggests intermixing of the deposited layers and the presence of TiO2 is evidence of oxidation. The samples annealed under pure H2 gas showed only TiH2 with no trace of structural transformation. RBS confirmed the intermixing of layers in the samples annealed under vacuum and H2(15%)/Ar(85%) gas mixture, while samples annealed under pure H2 gas did not show any intermixing of layers. ERDA revealed an average H content of ~ 3.5 at.% in CP-Ti and ~6.2 at.% in Ti6Al4V for samples annealed under H2(15%)/Ar(85%) gas mixture. We recorded an hydrogen content of ~19.5 at.% in CP-Ti annealed under pure H2 while ~25.5 at.% was found in Ti6Al4V annealed under the same conditions. When the thickness of the Pd catalyst layers was increased to 100 nm (i.e. Pd (100 nm)/Ti (25 nm)/Pd (100 nm)), only ~ 12.5 at.% and 11.2 at. % hydrogen content was recorded in samples prepared on CP-Ti and Ti6Al4V alloy respectively, both annealed under pure hydrogen for one hour as above.

This paper focuses on two experimental methods that give indicators linked to the impregnation level of the yarn / matrix interface, in the case of Textile Reinforced Concrete (TRC). These methods have been tested on three different glass yarns laid in a cementitious matrix, with three different impregnation levels resulting from the manufacturing process. The first method (comparative mercury intrusion porosity test) is based on the evaluation by mercury intrusion porosity of the pores volume associated to the porosity inside and near the yarn. The second method (flow test) consists in measuring the flow rate of water along the yarn, with imposed flow conditions. The physical parameters measured by these two methods are both related to the pore size and to the porosity of the yarn / matrix interface. The results of the two methods are discussed and drawn in parallel to a qualitative characterization of the yarn matrix interface made by scanning electron microscopy. As a result, the connection between the results of the two methods and the SEM characterization is studied. It is shown how these methods can participate to characterize the yarn impregnation. Limitations of the methods are also discussed.

Biofilms represent universal strategy for bacterial survival. Living in form of biofilms, bacteria acquire wide range of advantages over planktonically growing cultures. It can be assumed that nearly 99% of world bacterial population is living in form of biofilms. There are benefits and drawbacks associated with bacterial biofilms for mankind. Life in biofilms makes pathogens more effective and persistent through higher antibiotic resistance and helps them to hide before immune system of the host. Mycobacteria, which are capable of forming biofilms on variety of surfaces, differ from most of other bacteria by unique composition of their cell wall. It provides them with high resistance against physical or chemical damage. This is one of the reasons for considering Mycobacterium tuberculosis as a highly potent pathogen. The studies of mycobacterial biofilms are motivated by effort to improve or find new therapeutic methods. This work is aimed at morphological and proteomic comparative analyses of biofilms obtained from Mycobacterium smegmatis grown on surface of glass and silica/zirconium beads, on liquid medium surface or grown submerged in shaken planktonic culture. We have developed technique for preparation of "floating" biofilm sample to be observed in SEM. We have shown that the growth of...

Metal-semiconductor contacts have been widely studied in the past 60 years. These structures are of importance in the microelectronics industry. As the scaling down of silicon-based complementary metal-oxide-semiconductor (CMOS) devices becomes more and more challenging, new material and device structures to relax this physical limitation in device scaling are now required. Germanium (Ge) has been proposed as a potential alternative to silicon. In this thesis a systematic study of the thermally induced reaction of transition metals with the n-Ge substrate is outlined. Investigations in the change of the electrical properties of the metal germanide structures is studied in a wide range of temperatures. Current-voltage (I-V), capacitance-voltage (C-V), deep level transient spectroscopy (DLTS) and high-resolution Laplace-DLTS (L-DLTS) techniques have been used for the electrical characterization of the fabricated Schottky contacts. Results obtained indicate the variation of the electrical properties of these Schottky contacts can be attributed to combined effects of interfacial reactions and phase transformation during the annealing process. The barrier height distribution in identically prepared Schottky contacts on n-Ge (100) showed that the barrier heights and ideality factors varied from diode to diode even though they were identically fabricated. The properties of the n-Ge Schottky contacts have revealed a strong dependence on temperature. The current transport mechanism has been shown to be predominantly thermionic emission at high temperatures while at low temperatures, the Schottky contacts have exhibited the dominance of the generation-recombination current mechanism. The variation of the Schottky barrier heights at low temperatures have been attributed to barrier inhomogeneities at the metal-semiconductor (MS) interface. Results from defect characterization by DLTS show that the E-centre is the dominant defect introduced in n-Ge by electron beam deposition during contact fabrication and substitutional related defects are induced during the annealing process. The identification of some of the defects was achieved by using defect properties, defect signature, annealing mechanisms and annealing behaviour and comparing these properties to the results from theoretical defect models. Annealing showed that defects in Ge can be removed by low thermal budget of between 250–350°C. Finally, structural characterization of these samples was performed by scanning electron microscopy (SEM) and Rutherford backscattering spectrometry (RBS) techniques. From the SEM images it can be observed that the onset temperature for agglomeration in the 30 nm Ni/n-Ge (100), and Pt/-, Ir/- and Ru/n-Ge (100) systems occur at 500–600°C and 600–700°C, respectively. / Thesis (PhD)--University of Pretoria, 2010. / Physics / unrestricted

This master thesis studies the behaviour of two aluminium alloys in ultrasonic cleaning at two different intensities, as well as the effect of a cleaning solution, Formula 815 GD-NF on the same surface have been studied with respect to surface roughness and material composition. Methods like Light Optical Microscopy (LOM), Scanning Electron Microscopy (SEM), Energy Dispersive Spectroscopy (EDS) and 3D topography using white light interferometry (VSI) was used to study the surface and material composition. It was found that both the ultrasonic cleaning, as well as the solution itself both increase surface roughness of the samples. When crossing a threshold in ultrasonic intensity micro jet cavitation dislodge precipitates, or areas weakened by precipitate to form a large pit. And the following heat from the jet causes the surface to oxidise, becoming more brittle, and be broken up by other cavitation phenomena to cause rapid acceleration of surface roughness in an area originating from the pit.

The main subject of this diploma thesis is the study of the effect of humidity on the total sterilization effect of the dielectric barrier discharge. Sterilization is a process which can eliminate all forms of life. The plasma sterilization is one of the methods that are suitable for sterilization of temperature and chemical sensitive materials. This sterilization method was proved to be effective on the wide spectrum of procaryotic and eucaryotic microorganisms. Basically, the main inactivation factors for cells exposed to plasma are heat, UV radiation and various reactive species. Dielectric barrier discharge (DBD) operating at atmospheric pressure was used for the sterilization of the samples. The discharge was generated in dry air and in humid air. The plasma power densities were 2 160 mW.cm-3, 2 279 mW.cm-3 and 2 760 mW.cm-3 (dry air) or 2 326 mW.cm-3 and 2 850 mW.cm-3 (humid air). Humidity of air was achieved using a wash bottle filled with water through which air flowed into the DBD reactor. Fungi spores of Aspergillus niger were used as model microorganisms. Whatman paper No. 1 was used as the carrying medium. When comparing sterilization efficiency of humid and dry air operating at the same conditions, the higher sterilization effect was observed in humid air. The sterilization effect of the DBD generated in air was compared with results obtained during plasma generation in argon and nitrogen. At the same conditions, the highest sterilization effect was observed in argon, followed by humid air, nitrogen and dry air. It was found out that in our experimental setup the active species are probably the main inactivation mechanism. The influence of temperature on the inactivation of microorganisms was completely negligible. The discharge parameters were studied by means of the optical emission spectroscopy (OES). Plasma treated samples were analyzed employing scanning electron microscopy (SEM). Damage of the microorganisms due to the effect of plasma as well as plasma effect on the structure of the carrying medium was evaluated.

No description available.

No description available.