The development of a complete thermoelectric generator and its application on a display polarizer film was successfully accomplished in this thesis. A systematic study of the prospective thermoelectric materials, PEDOT:PSS-based and ${ZnON}$, used for the present application is presented. To the best of our knowledge, this is the first exploration of the thermoelectric parameters of ${ZnON}$ reported here. Thin-film deposition of these materials was performed via both solution- and vacuum-based techniques. In addition, certain doping mechanisms were tested in an attempt to further understand the correlation between electrical conductivity and Seebeck coefficient. A maximum power factor of $42{\mu}Wm^{-1}K^{-2}$ was achieved for the PEDOT:PSS-based thin film at room temperature. It was initially doped via 5vol% of DMSO and sequentially treated with ethylene glycol. Specifically, its electrical conductivity displayed a 2-fold increase after EG treatment, reaching a value of about 1632 Scm$^{-1}$. Systematic studies performed on the association between thin-film thickness and its Seebeck coefficient shows a decrease in the latter as the number of multilayers printed increases. Among the different $O_{2}/N_{2}$ ratios that were tested for ${ZnON}$ thin films, a maximum power factor value of 163${\mu}Wm^{-1}K{-2}$ was achieved with the lowest $O_{2}$ flow rate configuration. In contrast to PEDOT:PSS-based thin films, the ${ZnON}$ displayed the opposite effect on the relation of the Seebeck coefficient with respect to thin-film thickness. Furthermore, a heterostructure was also developed by implementing ${ZnO}$ nanowires into the ${ZnON}$ thin film. ${ZnO}$ nanowires have been fabricated through the hydrothermal method on inkjet-printed patterns of zinc acetate dihydrate. It has been demonstrated that with the right inkjet-printing parameters and substrate temperature, ${ZnO}$ nanowires can be effortlessly fabricated in accordance with the desired pattern variations under low temperature and mild conditions. Finally, a complete device of the thermoelectric generator was fabricated using the above materials and a special set-up developed in order to test the device on the polarizer. The power output achieved from a 1-thermoelectric couple under normal backlight illumination and ambient conditions was 23pW. Overall, it is thought that the particular design and proof of concept presented here can be the basis of a prospective energy harvesting scheme via thermoelectrics in future display-based handheld devices.

O presente trabalho investiga o fenômeno termodifusivo em dispersões coloidais de nanopartículas magnéticas de óxidos de ferro em água (ferrofluidos), com a formação de dupla camada elétrica em torno das partículas. A estabilidade da partícula em solução é controlada pela concentração de íons. Ao estabelecer uma diferença de temperatura através da amostra líquida, ocorre o efeito de termodifusão (efeito Soret) das partículas e de íons em solução. Este efeito é o movimento das partículas para o lado frio ou quente do gradiente de temperatura. O acúmulo para um dos lados do gradiente de temperatura depende das características da solução. O efeito Soret de ferrofluidos em soluções ácidas e básicas é descrito a partir da determinação experimental das grandezas físicas envolvidas na difusão das partículas. O coeficiente Soret ST e o coeficiente de difusão são determinados em experimentos ópticos de lente de matéria, utilizando o aparato experimental de Varredura-Z, e de espalhamento Rayleigh forçado para termodifusão. Para investigar a resposta dos íons ao gradiente de temperatura, são realizadas medidas do potencial termoelétrico em uma célula termoelétrica, gerado a partir da difusão das cargas dispersas no líquido. O potencial superficial das partículas também é investigado experimentalmente, para descrever a interação das partículas com o campo termoelétrico. Os experimentos são realizados em função da temperatura da amostra e usados para descrever os resultados ST(T) das partículas, a partir de equações dos principais modelos teóricos. Os resultados mostram as diferenças e semelhanças do efeito Soret das nanopartículas em soluções ácidas e básicas, e que em ambos os casos a termodifusão de nanopartículas reflete o comportamento termodifusivo dos íons dispersos em solução. / This work investigates the thermal diffusion phenomena in colloidal dispersions of iron oxide magnetic nanoparticles dispersed in water (ferrofluid). The particles are stable in water due to electrical double layer around the particles, controlled by the ionic concentration. A temperature gradient throughout the ferrofluid sample causes the thermodiffusion (Soret effect) of dispersed particles and ions. This effect is the movement of particles to the cold or hot side of the temperature gradient. The particles migration for a given side depends on the characteristics of the sample. The Soret effect of ferrofluids in acidic and basic solutions is described by the experimental measurements of the physical parameters associated to particles diffusion. The Soret coefficient ST and the mass diffusion coefficient are measured in the matter lens experiment in the Z-scan experimental setup, and by the use of Thermal Diffusion Forced Rayleigh Scattering experiments. Concerning the ionic response to the temperature gradient the thermoelectric field generated by charges diffusion is measured in a thermoelectric cell. The surface potential of the particles is also measured to describe its interactions with the thermoelectric field. These experiments are made as function of the temperature of the sample and the results are applied to describe the ST(T) of particles by the use of equations from the main theoretical models. The results show differences and resemblances of the Soret effect in acidic and basic nanoparticles solutions. In both kind of solutions the thermodiffusion of nanoparticles is mainly ruled by the thermodiffusion of ions dispersed in solution.

Many studies and experiments have been conducted over the years to find solutions to the electricity problem. This issue is not just related to how fossil fuels are dispensed. Also, the environmental concerns associated with using fossil fuels have become a severe issue, which is a major cause of environmental pollution and ozone layer damage. As such, the need for energy becomes one of the essential goals. Therefore, research has begun to revolve around thermoelectrics, which is a straightforward approach for generating energy, by converting heat directly into electricity. Cobalt antimonide (CoSb3) belongs to a broad family of materials with the skutterudite structure, which have been recently identified as potential new thermoelectric materials with high performance. The CoSb3 is one of the numerous promising thermoelectric materials in the intermediate temperature range. The binary CoSb3 is a narrow bandgap semiconductor with a relatively flat band structure and excellent electrical performance. The thermoelectric performance efficiency of binary CoSb3 is measured by its figure of merit. The figure of merit is important for thermoelectric materials and is primarily governed by the Seebeck coefficient because it exhibits a square dependence. The Seebeck coefficient of the CoSb3 can be affected by many factors that can either increase or decrease it. Strain is an important aspect for the transport properties, including the Seebeck coefficient. The goal of this thesis project is to study the effect of point defects and strain on the Seebeck coefficient of skutterudite CoSb3. The binary CoSb3 skutterudite was explored through density functional theory (DFT) to calculate the ground-state properties, in particular the Seebeck coefficient. Two different CoSb3 structures were considered, an ideal one (without any defects) and the other was termed real (containing defects). In both cases, the Seebeck coefficient and its response were studied while strain was applied by changing the volume of the structure. The non-equilibrium Green's function was used within a DFT simulation to get a transmission distribution, where it was essential for calculating the Seebeck coefficient. Moreover, oxygen molecules were placed over the (001) surface of 2 × 2 × 1 CoSb3 supercell to establish if oxidation leads to point defect formation. These simulations were carried out by DFT-based molecular dynamics. It is found that the strain affects the Seebeck coefficient in the ideal structure. At compression, the absolute value of the Seebeck coefficient increases.  By contrast, the Seebeck coefficient changed its sign from negative to positive and increased to 894 μVK−1at tension, which was unexpected. The electron density distribution map was explored to explain the behavior of the Seebeck coefficient at equilibrium, compression, and tension. It can be seen that the electron distribution between Co and Sb is increased at compression, implying an increased orbital overlap (covalent interaction). By contrast, the tension reduces the electron distribution between Sb and Co. The real structure induced by oxidation exhibits Sb vacancies. The See-beck coefficient is affected differently than that of the ideal structure. At equilibrium, the Seebeck coefficient increases to 151 μVK−1. The electron density distribution between Sb and Co is enhanced in the real structure compared to the ideal one. The most drastic change is found at tension, where the Seebeck coefficient reaches−270 μVK−1. It may be speculated that this occurs due to O which increases the orbital overlap. The strategy introduced in this work, an interplay of defects and strain effects, may be beneficial for other thermoelectric materials.

No description available.

No description available.

No description available.

No description available.

No description available.

Active research of SMAs has shown that its Seebeck coefficient is sensitive to its martensitic phase transformation and has the potential to determine the SMAs state of transformation. The combination of Shape Memory Alloys, which have a positive Seebeck coefficient, and Constantan which has a negative Seebeck coefficient (-35 mV/K) results in a thermocouple capable of measuring temperature. The work presented in this thesis is based on the development and design of this sensor. This sensor is used to study the hysteretic behaviour of SMAs. Although Shape Memory Alloys (SMAs) exhibit a myriad of nonlinearities, SMAs show two major types of nonlinear hysteresis. During cyclic loading of the SMAs, it is observed that one type of hysteretic behavior depends on the rate of heating the SMAs, whilst the variation of maximum temperature of an SMA in each cycle results in the other hysteretic behavior. This later hysteretic behavior gives rise to major and minor nonlinear loops of SMAs. The present work analyzes the nonlinearities of hysteretic envelopes which gives the different maximum temperatures reached for each hysteretic cycle with respect to stress and strain of the SMA. This work then models this behavior using Adaptive Neuro Fuzzy Inference System (ANFIS) and compares it to experimental results. The nonlinear learning and adaptation of ANFIS architecture makes it suitable to model the temperature path hysteresis of SMAs. / Master of Science

Aujourd’hui, les énergies renouvelables comme l’énergie éolienne, l’énergie solaire, l’énergie hydroélectrique et la thermoélectricité jouent un rôle essentiel dans la couverture de nos besoins en énergie. Parmi ces différentes sources d’énergie, la thermoélectricité, qui permet de convertir la chaleur en électricité ou inversement, attire une grande attention grâce à son large champ d’application. Les actuelles avancées dans la recherche thermoélectrique visent l’amélioration du rendement de conversion des modules thermoélectriques, à travers l’optimisation des propriétés thermoélectriques intrinsèques des matériaux utilisés (coefficient de Seebeck, conductivité électrique et conductivité thermique). Pour cela, différentes approches ont été étudiées (dopage, nouveau alliages, nanostucturation …). Parmi ces approches, la nanostructration des matériaux a été largement étudiée pour mener à bien cet objectif. Dans ce travail de thèse, nous nous sommes intéressés à étudier l’effet de la nanostructuration de surface des matériaux (silicium mesoporeux et oxyde de titane déposé en couches minces) par faisceaux laser ultra-court (picoseconde et femtoseconde) sur l’évolution de leurs propriétés thermoélectriques. Dans un premier temps, nous nous sommes focalisés sur l’étude des différents phénomènes physiques impliqués durant l’interaction laser-matière ainsi que sur la formation des différentes nanostructures résultantes (en forme de ripples, spikes, dots et autres) en fonction de la dose laser appliquée (la fluence et le nombre de pulses). La formation de ces nanostructures a été étudiée suivant deux régimes (stationnaire et dynamique). Après l’optimisation des paramètres conduisant à la formation de ces nanostructures, la caractérisation du coefficient de Seebeck et la conductivité électrique avant et après la nanostructuration de ces matériaux a été réalisée grâce à un nouveau dispositif de mesure (ZT-meter) développé au laboratoire GREMI. Les résultats de mesures montrent une importante amélioration du coefficient de Seebeck et la conductivité électrique après la nanostrucutration. Un facteur d’augmentation de la puissance thermoélectrique a été observé pour les deux matériaux étudiés ; notamment dans le cas de couches minces d’oxyde de titane (jusqu’à 500 fois). / Today, renewable energies such as wind, solar, hydropower and thermoelectricity play an essential role to cover our energy needs. Among these different sources of energy, thermoelectricity, which offers the ability to convert a heat into electricity or vice versa, has attracted a great attention due to its wide field of potential applications. The current advances in thermoelectric research are focusing on the improvement of the conversion efficiency of thermoelectric devices through optimizing and improving the thermoelectric properties of the thermoelectric materials (Seebeck coefficient, electrical conductivity and thermal conductivity). For this, different approaches (doping, new materials, nanostucturing...) have been investigated in the literature. Among these approaches, nanostructuring of materials is the most studied in the literature in order to improve the thermoelectric properties of materials. In this thesis work, we aimed to study the effect of surface nanostructuring of materials (mesoporous silicon and titanium oxide deposited in thin film) by ultra-short laser beams (picosecond and femtosecond) on the evolution of their thermoelectric properties. First, we focused on the study of various physical phenomena involved during the laser-matter interaction that yield to the formation of very different nanostructures in form of ripples, spikes, dots and others as function of the applied laser dose (fluence and number of pulses). The formation of these nanostructures has been studied in two regimes (stationary and dynamic). After optimizing the laser parameters leading to the formation of such nanostructures, a characterization of Seebeck coefficient and the electrical conductivity before and after the nanostructuring of these materials was carried out by using a new experimental setup (ZT-meter) designed and validated in GREMI laboratory. The results of measurements showed an important improvement of Seebeck coefficient and electrical conductivity after nanostructuring. This important improvement observed with the both materials leaded to a strong increase in the thermoelectric power factor (reaching roughly 50000%).