The electric power systems in U.S. Navy ships supply energy to sophisticated systems for weapons, communications, navigation and operation. The reliability and survivability of a Shipboard Power System (SPS) are critical to the mission of a Navy ship, especially under battle conditions. When a weapon hits the ship in the event of battle, it can cause severe damage to the electrical systems on the ship. Researchers in the Power System Automation Laboratory (PSAL) at Texas A&M University have developed methods for performing reconfiguration of SPS before or after a weapon hit to reduce the damage to SPS. Reconfiguration operations change the topology of an SPS. When a system is stressed, these topology changes and induced dynamics of equipment due to reconfiguration might cause voltage instability, such as progressive voltage decreases or voltage oscillations. SPS stability thus should be assessed to ensure the stable operation of a system during reconfiguration. In this dissertation, time frames of SPS dynamics are presented. Stability problems during SPS reconfiguration are classified as long-term stability problems. Since angle stability is strongly maintained in SPS, voltage stability is studied in this dissertation for SPS stability during reconfiguration. A test SPS computer model, whose simulation results were used for stability studies, is presented in this dissertation. The model used a new generalized methodology for modeling and simulating ungrounded stiffly grounded power systems. This dissertation presents two new indices, a static voltage stability index (SVSILji) and a dynamic voltage stability index (DVSI), for assessing the voltage stability in static and dynamic analysis. SVSILji assesses system stability by all lines in SPS. DVSI detects local bifurcations in SPS. SVSILji was found to be a better index in comparison with some indices in the literature for a study on a two-bus power system. Also, results of DVSI were similar to the results of conventional bifurcation analysis software when applied to a small power system. Using SVSILji and DVSI on the test SPS computer model, three of four factors affection voltage stability during SPS reconfiguration were verified. During reconfiguration, SVSILji and DVSI are used together to assess SPS stability.

The next generation of U.S. Navy ships will see the integration of the propulsion and electrical systems as part of the all-electric ship. This new architecture brings advantages and challenges. One of the challenges is to develop a stable power system that can ride through various issues such as faults or changes in load. style='mso-spacerun:yes'> While terrestrial systems have been studied for a long time related to stability, the unique characteristics of the shipboard power system mean that not all of these results are directly applicable to the all-electric ship. Because of the new shipboard power system structure, more generators are required to be connected in parallel to supply the power needed. Control of parallel generators has been done for years in terrestrial systems; however, the application of an advanced control technique has not been applied in the All-Electric Ship. The challenge is to apply an advanced control technique to the all-electric shipboard power system that will maintain stability of multiple generator systems, keeping in mind that the generators could be dissimilar in ratings. style='mso-spacerun:yes'> For that reason, the control techniques used to solve the problem need to be developed or adapted for test cases that are similar to the electric ship configuration. This dissertation provides a description of an effort to implement a robust control scheme on the all-electric ship. style='mso-spacerun:yes'> The proposed solution is to apply H∞ Robust Control as an advanced control technique, with realistic constraints to keep the shipboard power system within stability margins during normal and abnormal operating scenarios. In this work, H∞ Robust Control has been developed in the form of state space equations which are optimized using linear matrix implementation. The developed H∞ Control has been implemented on the different operating scenarios to validate the functionality and to compare it with another control technique. style='mso-spacerun:yes'> Test case results for one-generator, two-generator similar and two-generator dissimilar have been described. style='mso-spacerun:yes'> Stability indicators have been determined and compared for various types of faults and transients for removing and adding static and dynamic loads. The research provides the foundation for applications of advanced control techniques for the next generation all-electric ship.

Todays protection schemes for shipboard applications, such as the zone-based differential protection, are efficient, fast, and reliable for fault detection. However, these protection schemes do not consider the system stability or power balance problems that occur with fault isolation and the system reconfiguration. This thesis focuses on developing the extended protection function including the fast reconfiguration function that intends to maintain the power balance of the unfaulted subsystem. Graph theory is utilized to represent the shipboard power system topology in matrices, and matrix operations are developed to represent the corresponding power system topology change and evaluate the outcome of the fault. Intelligent search algorithms are implemented to find the possible system configuration after fault isolation with balanced power generation and load through merging possible connected systems and priority-based load shedding. The algorithms are successfully implemented in MATLAB miles and tested on various shipboard power system configurations and fault scenarios.

The shipboard power system supplies energy to sophisticated systems for weapons, communications, navigation, and operation. After a fault is encountered, reconfiguration of a shipboard power system becomes a critical activity that is required to either restore service to a lost load or to meet some operational requirements of the ship. Reconfiguration refers to changing the topology of the power system in order to isolate system damage and/or optimize certain characteristics of the system related to power efficiency. When finding the optimal state, it is important to have a method that finds the desired state within a short amount of time, in order to allow fast response for the system. Since the reconfiguration problem is highly nonlinear over a domain of discrete variables, the genetic algorithm method is a suitable candidate. In this thesis, a reconfiguration methodology, using a genetic algorithm, is presented that will reconfigure a network, satisfying the operational requirements and priorities of loads. Graph theory is utilized to represent the shipboard power system topology in matrices. The reconfiguration process and the genetic algorithm are implemented in MATLAB and tested on an 8-bus power system model and on larger power system with distributed generators by considering different fault scenarios. Each test system was reconfigured in three different ways: by considering load priority, without considering load priority, and by combining priority factor and magnitude factor. The test results accuracy was verified through hand checking.

This work discusses the implementation of a Unique Ships Grid design that utilizes Energy Storage. This Unique Ships Grid is used to enhance the efficiency of a Construction Single-Hull River Tender previously discussed and assessed by the Army Corps of Engineers and the United States Coast Guard (USCG). This Grid Design is shown to be both in compliance with applicable regulations and reliable due to built-in redundancy. Compliance with regulations and redundancy are both prized by the Maritime Community and the USCG. An applicable Heuristic Design Methodology is provided in conjunction with the Unique Ships Grid. This Design Methodology can be used with a simple load analysis and results in a Load Center breakdown and the sizing of Cables, Generators, Inverter, and required Energy Storage. This design process is shown to provide an inherent margin for growth and safety. This design process is quick and results in values necessary to do a cost analysis, environmental impact survey, and stability analysis (Ship Stability not Electrical Stability). / Master of Science

The electric power systems in U.S. Navy ships supply energy to sophisticated systems for weapons, communications, navigation and operation. The reliability and survivability of the Shipboard Power System (SPS) are critical to the mission of a surface combatant ship, especially under battle conditions. In the event of battle, various weapons might attack a ship. When a weapon hits the ship it can cause severe damage to the electrical system on the ship. This damage can lead to de-energization of critical loads on a ship that can eventually decrease a ship’s ability to survive the attack. It is very important, therefore, to maintain availability of energy to the connected loads that keep the power systems operational. Technology exists that enables the detection of an incoming weapon and prediction of the geographic area where the incoming weapon will hit the ship. This information can then be used to take reconfiguration actions before the actual hit so that the actual damage caused by the weapon hit is reduced. The Power System Automation Lab (PSAL) has proposed a unique concept called "Predictive Reconfiguration" which refers to performing reconfiguration of a ship’s power system before a weapon hit to reduce the potential damage to the electrical system caused by the impending weapon hit. The concept also includes reconfiguring the electrical system to restore power to as much of the healthy system as possible after the weapon hit. This dissertation presents a new methodology for Predictive Reconfiguration of a Shipboard Power System (SPS). This probabilistic approach includes a method to assess the damage that will be caused by a weapon hit. This method calculates the expected probability of damage for each electrical component on the ship. Also a heuristic method is included, which uses the expected probability of damage to determine reconfiguration steps to reconfigure the ship’s electrical network to reduce the damage caused by a weapon hit. This dissertation also presents a modified approach for performing a reconfiguration for restoration after the weapon hits the system. In this modified approach, an expert system based restoration method restores power to loads de-energized due to the weapon hit. These de-energized loads are restored in a priority order. The methods were implemented using multi-agent technology. A test SPS model based on the electrical layout of a non-nuclear surface combatant ship was presented. Complex scenarios representing electrical casualties caused due to a weapon hit, on the test SPS model, were presented. The results of the Predictive Reconfiguration methodology for complex scenarios were presented to illustrate the effectiveness of the developed methodology.

The electric power systems in U.S. Navy ships supply energy to sophisticated systems for weapons, communications, navigation and operation. The reliability and survivability of the Shipboard Power System (SPS) are critical to the mission of a surface combatant ship, especially under battle conditions. In the event of battle, various weapons might attack a ship. When a weapon hits the ship it can cause severe damage to the electrical system on the ship. This damage can lead to de-energization of critical loads on a ship that can eventually decrease a ship’s ability to survive the attack. It is very important, therefore, to maintain availability of energy to the connected loads that keep the power systems operational. Technology exists that enables the detection of an incoming weapon and prediction of the geographic area where the incoming weapon will hit the ship. This information can then be used to take reconfiguration actions before the actual hit so that the actual damage caused by the weapon hit is reduced. The Power System Automation Lab (PSAL) has proposed a unique concept called "Predictive Reconfiguration" which refers to performing reconfiguration of a ship’s power system before a weapon hit to reduce the potential damage to the electrical system caused by the impending weapon hit. The concept also includes reconfiguring the electrical system to restore power to as much of the healthy system as possible after the weapon hit. This dissertation presents a new methodology for Predictive Reconfiguration of a Shipboard Power System (SPS). This probabilistic approach includes a method to assess the damage that will be caused by a weapon hit. This method calculates the expected probability of damage for each electrical component on the ship. Also a heuristic method is included, which uses the expected probability of damage to determine reconfiguration steps to reconfigure the ship’s electrical network to reduce the damage caused by a weapon hit. This dissertation also presents a modified approach for performing a reconfiguration for restoration after the weapon hits the system. In this modified approach, an expert system based restoration method restores power to loads de-energized due to the weapon hit. These de-energized loads are restored in a priority order. The methods were implemented using multi-agent technology. A test SPS model based on the electrical layout of a non-nuclear surface combatant ship was presented. Complex scenarios representing electrical casualties caused due to a weapon hit, on the test SPS model, were presented. The results of the Predictive Reconfiguration methodology for complex scenarios were presented to illustrate the effectiveness of the developed methodology.

The recent development of Integrated Power Systems (IPS) for shipboard application has opened the horizon to introduce new technologies that address the increasing power demand along with the associated performance specifications. Similarly, the Shipboard Power System (SPS) features system components with multiple dynamic characteristics and require stringent regulations, leveraging a challenge for an efficient system level management. The shipboard power management needs to support the survivability, reliability, autonomy, and economy as the key features for design consideration. To address these multiple issues for an increasing system load and to embrace future technologies, an autonomic power management framework is required to maintain the system level objectives. To address the lack of the efficient management scheme, a generic model-based holistic power management framework is developed for naval SPS applications. The relationship between the system parameters are introduced in the form of models to be used by the model-based predictive controller for achieving the various power management goals. An intelligent diagnostic support system is developed to support the decision making capabilities of the main framework. Naïve Bayes’ theorem is used to classify the status of SPS to help dispatch the appropriate controls. A voltage control module is developed and implemented on a real-time test bed to verify the computation time. Variants of the limited look-ahead controls (LLC) are used throughout the dissertation to support the management framework design. Additionally, the ARIMA prediction is embedded in the approach to forecast the environmental variables in the system design. The developed generic framework binds the multiple functionalities in the form of overall system modules. Finally, the dissertation develops the distributed controller using the Interaction Balance Principle to solve the interconnected subsystem optimization problem. The LLC approach is used at the local level, and the conjugate gradient method coordinates all the lower level controllers to achieve the overall optimal solution. This novel approach provides better computing performance, more flexibility in design, and improved fault handling. The case-study demonstrates the applicability of the method and compares with the centralized approach. In addition, several measures to characterize the performance of the distributed controls approach are studied.

With the increasing interest in distribution automation, distribution power flow is important for applications like VAR planning, switching, state estimation and especially optimization. Typically, a distribution system originates at a substation and continues to a lower voltage for delivery to the customers. There are several tools for transmission system analysis. These tools include Newton Raphson, Gauss Seidel and fast decoupled techniques. These techniques however sometimes fail to converge when applied to distribution systems due to their higher resistance/reactance (R/X) ratio of the lines, making them ill conditioned. Distribution systems typically have a radial topological structure where the loads are not always constant power. With the increase in distributed generation (DG) there is a critical need to develop analysis tools to study the effect they will have on the distribution systems. Also, shipboard power systems are different from terrestrial distribution systems, as they are tightly coupled and have multiple generators. This dissertation focuses on developing a software program to perform the power flow analysis of terrestrial as well as shipboard power systems. Components are modeled considering the mutual coupling of cables and the tightly coupled nature of the ship systems. The algorithm is built and tested on I test cases. The distributed generator is modeled as both a PQ (constant power factor) and a PV (constant voltage) node. This dissertation also focuses on reconfiguration for restoration of unbalanced distribution systems. Reconfiguration is changing the status (OFF/ON) of switches and reconfiguration for restoration is changing the switch status to maximize the supply to loads that are left unsupplied after fault removal. Methods exist for restoration of distribution systems and can be categorized into heuristics, knowledge based, meta-heuristics and intelligent techniques. However, the application of these methods have not considered the unbalanced nature of distribution system operation with mutual coupling. The restoration in this dissertation is achieved using optimization with multiple objectives; that of maximizing the load giving priority to vital loads and minimizing the number of switch operations. Also a restoration scheme for shipboard power systems with an IPS and distributed generation has been developed. Restoration with possible islanding is demonstrated.

Future all-electric warships with an integrated power system (IPS) are capable of unlocking large amounts of power dedicated to propulsion and redirecting this power for service loads, weapon loads, and other loads. The IPS for all-electric ships combines the power generation system, electric propulsion system, power distribution system, and power control and management system all together. The move to IPS design will significantly improve efficiency, effectiveness, and survivability. To meet the needs of the US Navy, enhancing survivability by reducing susceptibility to damage, a IPS prefers decentralized reconfiguration system is preferred for IPS instead of traditional reconfiguration techniques used for terrestrial power grids. A multi-agent system (MAS) is a loosely coupled network composed of several agents. These agents interact with their environments and communicate with each other to solve problems that are beyond the individual capabilities or knowledge of each single agent. Because of its decentralized feature and lack of a global control feature, MAS appears to be the best candidate for IPS reconfiguration. This research work proposes a new model of an IPS, based on the Naval Combat Survivability, DC Distribution Test-bed (NCS DCDT). The new model combines the electric power generation system, electric propulsion system, and AC-DC zonal distribution system. To decrease the probability of distribution zones losing power, the new model modifies original design of the zonal distribution system in NCS DCDT. Another main endeavor of this research work is to design a MAS for reconfiguration of an IPS with AC-DC zonal distribution system. The MAS consists of three sub-MAS, named power generation MAS, propulsion MAS, and distribution MAS, and includes forty-one different agents which are instances of nineteen different abstract agent classes. The MAS is implemented with JAVA/JADE software and simulated on a platform of JADE 3.4.1 and JAVA jdk 1.5.0_08. Simulation results show that the MAS can execute reconfiguration functions such as fault area isolation, automatic switching, and load shedding.