Thermometry measurements were carried out using planar laser induced phosphorescence in conjunction with thermographic phosphors in heated turbulent jets and laminar flames in order to further develop the technique for usage in flames. Two dimensional thermometry measurements are essential to improve the understanding of combustion processes, as temperature governs soot pyrolysis, leading to soot formation. Two particular thermographic phosphors, BAM and YAG:Dy were tested and compared and it was found that they were unsuitable for gas phase flame thermometry measurements. Soot volume fraction measurements were carried out using planar two colour laser induced incandescence in gaseous and liquid fuel flames. The gas fuel flames were diluted with nitrogen, carbon dioxide and hydrogen individually and then with nitrogen and hydrogen together, as well as carbon dioxide and hydrogen together, separately. Results revealed the dilution effects of the gases on the soot formation process, where increasing nitrogen percentage in the flow decreased SVF, carbon dioxide reduced it further and hydrogen showed no marked difference. Biodiesels were compared with each other and with diesel in a wick burner in order to analyse their compositional effects on soot. Biodiesel composition was measured using gas chromatography. The sooting tendencies of the biodiesels were as expected, fuels with a longer average carbon chain length and a higher degree of unsaturation were found to produce more soot than shorter, more saturated fuels. Diesel was sootier than all of the biofuels tested, due to containing aromatics and a lower oxygen content. A pilot study was also done, where the performance and emissions of biofuels and biofuel-diesel blends were tested in a gas turbine engine, in order to relate the investigation to real world situations.

Sérios problemas ambientais têm origem em processos de combustão incompletos. Entre os produtos indesejados está a fuligem, considerada como um dos principais fatores da mudança climática observada nos último anos. Desta forma, ferramentas para diagnóstico da emissão de material particulado se fazem necessárias. Com o advento do laser, o desenvolvimento de técnicas óticas não intrusivas teve início. Dentre elas, destaca-se a técnica denominada incandescência induzida por laser (laser induced incandescence – LII), a qual pode gerar resultados resolvidos no espaço para a fração volumétrica de fuligem. Neste contexto, este trabalho apresenta um estudo experimental sobre a produção de fuligem em duas situações: na primeira, foram estudadas chamas laminares pré-misturadas de etileno e ar aplicando-se a técnica LII. Os resultados foram calibrados a partir da fração volumétrica de fuligem média empregando a técnica de extinção de luz, obtendo-se, então, resultados quantitativos espacialmente resolvidos da fração volumétrica de fuligem. A utilização de diferentes gases no escoamento anular também foi avaliada. A segunda situação abordada envolve o estudo de chamas laminares não pré-misturadas utilizando o gás natural como combustível. O impacto da diluição de inertes em diferentes proporções sobre a fração volumétrica de fuligem em diversas alturas da chama foi estudado por meio da técnica LII. Os resultados obtidos foram comparados à outros resultados presentes na literatura e servirão como validação de futuros modelos de formação de fuligem. / Serious environmental problems are assigned to incomplete combustion processes. Among the unwanted products, soot can be related as an important factor of climate changes observed in the last years. Thus, particulate material emissions diagnostic tools are necessary. Due the laser advent, the development of non-intrusive optical techniques was possible. One of the most importante technique is the laser induced incandescence, LII, which can generate spatially and temporally resolved results of soot volume fraction. In this context, an experimental study regarding the soot production was developed in two different situations: in the first one, premixed laminar flames of ethylene and air were investigated by applying the LII technique. The results were calibrated through the average of soot volume fraction results obtained by the light extinction technique. Therefore, it was possible to obtain quantitative results of spatially resolved soot volume fraction. Different gases employment at the annular flow were also evaluated. The second situation studied involves the analysis of natural gas laminar non-premixed flames. The impact of different inert gas dilution ratio on the soot volume fraction at different heights of the flame was evaluated by the LII technique. The results were compared to other authors and will serve as validation for future soot formation models.

Sérios problemas ambientais têm origem em processos de combustão incompletos. Entre os produtos indesejados está a fuligem, considerada como um dos principais fatores da mudança climática observada nos último anos. Desta forma, ferramentas para diagnóstico da emissão de material particulado se fazem necessárias. Com o advento do laser, o desenvolvimento de técnicas óticas não intrusivas teve início. Dentre elas, destaca-se a técnica denominada incandescência induzida por laser (laser induced incandescence – LII), a qual pode gerar resultados resolvidos no espaço para a fração volumétrica de fuligem. Neste contexto, este trabalho apresenta um estudo experimental sobre a produção de fuligem em duas situações: na primeira, foram estudadas chamas laminares pré-misturadas de etileno e ar aplicando-se a técnica LII. Os resultados foram calibrados a partir da fração volumétrica de fuligem média empregando a técnica de extinção de luz, obtendo-se, então, resultados quantitativos espacialmente resolvidos da fração volumétrica de fuligem. A utilização de diferentes gases no escoamento anular também foi avaliada. A segunda situação abordada envolve o estudo de chamas laminares não pré-misturadas utilizando o gás natural como combustível. O impacto da diluição de inertes em diferentes proporções sobre a fração volumétrica de fuligem em diversas alturas da chama foi estudado por meio da técnica LII. Os resultados obtidos foram comparados à outros resultados presentes na literatura e servirão como validação de futuros modelos de formação de fuligem. / Serious environmental problems are assigned to incomplete combustion processes. Among the unwanted products, soot can be related as an important factor of climate changes observed in the last years. Thus, particulate material emissions diagnostic tools are necessary. Due the laser advent, the development of non-intrusive optical techniques was possible. One of the most importante technique is the laser induced incandescence, LII, which can generate spatially and temporally resolved results of soot volume fraction. In this context, an experimental study regarding the soot production was developed in two different situations: in the first one, premixed laminar flames of ethylene and air were investigated by applying the LII technique. The results were calibrated through the average of soot volume fraction results obtained by the light extinction technique. Therefore, it was possible to obtain quantitative results of spatially resolved soot volume fraction. Different gases employment at the annular flow were also evaluated. The second situation studied involves the analysis of natural gas laminar non-premixed flames. The impact of different inert gas dilution ratio on the soot volume fraction at different heights of the flame was evaluated by the LII technique. The results were compared to other authors and will serve as validation for future soot formation models.

Sérios problemas ambientais têm origem em processos de combustão incompletos. Entre os produtos indesejados está a fuligem, considerada como um dos principais fatores da mudança climática observada nos último anos. Desta forma, ferramentas para diagnóstico da emissão de material particulado se fazem necessárias. Com o advento do laser, o desenvolvimento de técnicas óticas não intrusivas teve início. Dentre elas, destaca-se a técnica denominada incandescência induzida por laser (laser induced incandescence – LII), a qual pode gerar resultados resolvidos no espaço para a fração volumétrica de fuligem. Neste contexto, este trabalho apresenta um estudo experimental sobre a produção de fuligem em duas situações: na primeira, foram estudadas chamas laminares pré-misturadas de etileno e ar aplicando-se a técnica LII. Os resultados foram calibrados a partir da fração volumétrica de fuligem média empregando a técnica de extinção de luz, obtendo-se, então, resultados quantitativos espacialmente resolvidos da fração volumétrica de fuligem. A utilização de diferentes gases no escoamento anular também foi avaliada. A segunda situação abordada envolve o estudo de chamas laminares não pré-misturadas utilizando o gás natural como combustível. O impacto da diluição de inertes em diferentes proporções sobre a fração volumétrica de fuligem em diversas alturas da chama foi estudado por meio da técnica LII. Os resultados obtidos foram comparados à outros resultados presentes na literatura e servirão como validação de futuros modelos de formação de fuligem. / Serious environmental problems are assigned to incomplete combustion processes. Among the unwanted products, soot can be related as an important factor of climate changes observed in the last years. Thus, particulate material emissions diagnostic tools are necessary. Due the laser advent, the development of non-intrusive optical techniques was possible. One of the most importante technique is the laser induced incandescence, LII, which can generate spatially and temporally resolved results of soot volume fraction. In this context, an experimental study regarding the soot production was developed in two different situations: in the first one, premixed laminar flames of ethylene and air were investigated by applying the LII technique. The results were calibrated through the average of soot volume fraction results obtained by the light extinction technique. Therefore, it was possible to obtain quantitative results of spatially resolved soot volume fraction. Different gases employment at the annular flow were also evaluated. The second situation studied involves the analysis of natural gas laminar non-premixed flames. The impact of different inert gas dilution ratio on the soot volume fraction at different heights of the flame was evaluated by the LII technique. The results were compared to other authors and will serve as validation for future soot formation models.

Combustion-generated carbon black nano particles, or soot, have both positive and negative effects depending on the application. From a positive point of view, it is used as a reinforcing agent in tires, black pigment in inks, and surface coatings. From a negative point of view, it affects performance and durability of many combustion systems, it is a major contributor of global warming, and it is linked to respiratory illness and cancer. Laser-Induced Incandescence (LII) was used in this study to measure soot volume fractions in four steady and twenty-eight pulsed ethylene diffusion flames burning at atmospheric pressure. A laminar coflow diffusion burner combined with a very-high-speed solenoid valve and control circuit provided unsteady flows by forcing the fuel flow with frequencies between 10 Hz and 200 Hz. Periodic flame oscillations were captured by two-dimensional phase-locked LII images and broadband luminosity images for eight phases (0°- 360°) covering each period. A comparison between the steady and pulsed flames and the effect of the pulsation frequency on soot volume fraction in the flame region and the post flame region are presented. The most significant effect of pulsing frequency was observed at 10 Hz. At this frequency, the flame with the lowest mean flow rate had 1.77 times enhancement in peak soot volume fraction and 1.2 times enhancement in total soot volume fraction; whereas the flame with the highest mean flow rate had no significant change in the peak soot volume fraction and 1.4 times reduction in the total soot volume fraction. A correlation (ƒv Reˉ1 = a+b· Str) for the total soot volume fraction in the flame region for the unsteady laminar ethylene flames was obtained for the pulsation frequency between 10 Hz and 200 Hz, and the Reynolds number between 37 and 55. The soot primary particle size in steady and unsteady flames was measured using the Time-Resolved Laser-Induced Incandescence (TIRE-LII) and the double-exponential fit method. At maximum frequency (200 Hz), the soot particles were smaller in size by 15% compared to the steady case in the flame with the highest mean flow rate.

<p dir="ltr">Soot is a byproduct formed during incomplete combustion of hydrocarbon fuels. Atmospheric soot from aircraft emissions increases local air temperatures, drives cloud formation, and decreases albedo on snow and ice: three factors that promote global warming. It is also potentially harmful to humans and has been associated with negative effects on heart and lung health. Operationally, soot formation indicates an inefficiency in combustion and can cause deterioration in aircraft engines. Modeling soot formation in complex flow fields is difficult and has been largely unsuccessful. In-situ soot measurements at relevant conditions can inform the design and operation of aircraft engines with reduced soot emissions. Laser-induced incandescence (LII) is a diagnostic that allows for non-intrusive measurements of soot volume fraction and primarily particle size in combustion environments. It involves laser-heating soot particles to temperatures at which they incandescence and measuring the radiated signal. The strong absorption capabilities and high sublimation temperature of soot make this diagnostic highly selective against the detection of other species. A coupled set of differential equations can be used to model the change in temperature and mass of a soot particle over time. Methods for modeling the fundamental processes in LII were reviewed in this work and comparisons were made between several different models.</p><p dir="ltr">International Sooting Flame target conditions were used to form a laminar diffusion flame in a Yale burner with a range of soot levels. Soot volume fraction measurements were conducted and compared with other experimental values to validate the accuracy of the experimental setup and techniques used. A calibration was performed using a laser extinction measurement from a previous study. Results showed an overall increase in soot volume fraction with increasing percentages of ethylene, as well as a transition in the peak location. Time-resolved LII was conducted at 10 MHz to determine the primary particle size of soot particles. Larger primary particles were observed with increasing height for flames with higher ethylene content. Changes in the soot formation and surface growth rates are suspected factors in the observed trends in the data. </p><p dir="ltr">The overall objective of this study was to validate an experimental setup for Laser-Induced Incandescence using a laminar diffusion flame. LII measurements were successfully demonstrated using the same diagnostic setup in a liquid-fueled swirl-stabilized flame at aircraft engine-relevant conditions. This study sets the groundwork for further investigation into aircraft soot generation using LII. </p>