Le couplage covalent sur surface métallique en UHV (Ultra High Vacuum) est une technique émergente permettant de synthétiser des structures moléculaires impossibles à obtenir par la chimie en solution (nanorubans de graphène, polymères 2D par exemple). Aujourd'hui, le plus grand défi reste le développement de ces réactions sur des surfaces isolantes pour différentes applications comme, par exemple, l'électronique moléculaire. En particulier, le couplage de dérivés d'acides benzoïques, greffés sur les surfaces de carbonate de calcium en UHV par des groupes carboxyliques, a été démontré récemment pour la première fois. Lors de ces travaux, nous avons dans un premier temps synthétisé des molécules précurseurs de réactions de couplage (homo-couplage d'éthyne, photopolymérisation, polycondensation et réaction d'Ullmann) sur des surfaces de carbonate de calcium en UHV. Par la suite, nous avons mené cette étude à l'échelle macroscopique (semi-préparatoire), par greffage de molécules sur des microparticules de carbonate de calcium, puis activation de la réaction, et enfin dissolution du substrat afin d'extraire le produit final. Les microparticules ont été obtenues par broyage de produit commercial ainsi que par spray pyrolyse et complètement caractérisées par FTIR, ATG/DTG, DRX, MEB et BET. Les réactions de couplage ont été activées par deux méthodes sans solvant: par broyage dans une broyeuse planétaire ou par traitement thermique sous vide. Alors qu'en UHV le couplage de l'acide 4-iodobenzoïque donne l'acide biphenyldicarboxylique, en mécanochimie nous avons obtenu l'acide benzoïque et par activation thermique l'éther dibenzoïque. / Covalent coupling on metallic surfaces in UHV (Ultra High Vacuum) conditions is a new method for preparing molecular structures otherwise impossible to achieve in solution (graphene nanoribbons, 2D polymers for instance). The major challenge is now to extend these reactions from metallic to insulating surfaces, for future applications as, for instance, in molecular electronics. In particular, the coupling reaction of benzoic acid derivatives, grafted on calcite via carboxylic groups, has been demonstrated for the first time in UHV conditions. In the first part of this work, we synthesized precursor molecules for specific reactions (homocoupling of ethynes, photopolymerization, polycondensation and Ullmann reaction) on calcium carbonate in UHV conditions. In the second part of this work we extended this investigation up to the macroscale level (semi-preparative) by grafting molecules on calcium carbonate microparticles, followed by reaction activation and finally by dissolution of the substrate in order to recover the coupling products. The calcium carbonate microparticles were prepared by grinding commercial product or by spray pyrolysis and were fully characterized by FTIR, TG/DTG, XRD, SEM and BET techniques. Then, after grafting of organic reactant, the reactions were activated with two different solvent-free methods: by grinding in a planetary milling machine or by heating the samples in a furnace under vacuum. Whereas in UHV conditions, 4-iodobenzoic acid affords biphenyldicarboxylic acid, mechanochemical condition gives benzoic acid and thermal activation the dibenzoic acid ether.

Wood is a renewable resource and versatile material used in tasks ranging from tools and furniture to advanced engineering structures. Although wood is light, mechanically robust, environmentally friendly, and abundant, some inherent properties of wood, such as degradation due to moisture and UV radiation from sunlight, are less desirable for extended service life and dimensional stability. In this dissertation, a novel surface modification of wood is explored by depositing nano-sized titania particles on wood veneers and cross-laminated timber (CLT) blocks by liquid-precursor flame spray pyrolysis to confer reversible wettability switching and enhanced durability to UV irradiation. The reaction between a flame source and a titanium precursor in isopropyl alcohol under controlled air pressure created a micrometer-scale thin TiO2 coating on wood that turns the treated wood superhydrophobic with a water contact angle (WCA) of >=150°. Morphological studies suggest the coating is comprised of sub-100 nm TiO2 individual and aggregated particles, creating a very porous microstructure. The coating consists of TiO2 rich in the anatase phase (>60%) with an average crystal size of 18 and 32 nm for the anatase and rutile phases, respectively. The wettability switching characteristics of the surface of TiO2-wood veneers from superhydrophobicity to superhydrophilicity (WCA ~0°) and again back to superhydrophobicity are examined through UV exposure (0.0032 W/m2), WCA measurements, and vacuum drying at ~0.14 mbar. The color and gloss spectrometry results of the TiO2-treated CLT samples indicate that the coating offered better resistance to discoloration and gloss change than the uncoated samples during the 8-week accelerated weathering conditions. The data shows that the FSP-treated CLT samples were more than two times more effective in preventing discoloration and changes in natural luster, as evidenced by the significant differences in L*, a*, b*, and gloss values. Moreover, the FSP treatment might have played a role in preventing weathering defects, such as splits and cracks. In addition, the FSP-treated CLT specimens were able to reduce variability in the samples more effectively than the control group. Overall, the findings of the study indicate that liquid-precursor FSP has the potential to serve as a facile, economically viable, and less energy-intensive approach to modify wooden surfaces for improved hydrophobicity, as well as to provide shielding against the deteriorating impacts of UV radiation and moisture exposure. Keywords: wood modification, flame spray pyrolysis, titania coating, superhydrophobic coating, particle deposition, wettability switching

The role of sensor technology is obvious in improvement and optimization of many industrial processes. The sensor films, which are considered the core of chemical sensors, have the capability to detect the presence and concentration of a specific chemical substance. Such sensor films achieve selectivity by detecting the interaction of the specific chemical substance with the sensor material through selective binding, adsorption and permeation of analyte. This research focuses on development and verification of a comprehensive mathematical model of mixed metal oxide thin film growth using spray pyrolysis technique (SPT). An experimental setup is used to synthesize mixed metal oxide films on a heated substrate. The films are analyzed using a variety of characterization tools. The results are used to validate the mathematical model. There are three main stages to achieve this goal: 1) A Lagrangian-Eulerian method is applied to develop a CFD model of atomizing multi-component solution. The model predicts droplet characteristics in flight, such as spatial distribution of droplet size and concentration. 2) Upon reaching the droplets on the substrate, a mathematical model of multi-phase transport and chemical reaction phenomena in a single droplet is developed and used to predict the deposition of thin film. The various stages of droplet morphology associated with surface energy and evaporation are predicted. 3) The processed films are characterized for morphology and chemical composition (SEM, XPS) and the data are used to validate the models as well as investigate the influence of process parameters on the structural characteristics of mixed metal oxide films. The structural characteristics are investigated of nano structured thin films comprising of ZnO, SnO2, ZnO+In2O3 and SnO2+In2O3 composites. The model adequately predicts the size distribution and film thickness when the nanocrystals are well-structured at the controlled temperature and concentration.

Semiconductors such as CuInGaSe2 and CdTe have been investigated as absorber layer materials for thin film solar cells since their band gap matches with the solar spectrum. Films as thin as 2m are sufficient for the absorption of the visible part of solar radiation, because they are characterized by a high absorption coefficient. However, the scarcity and high costs of Indium, Gallium and Tellurium have led to concerns on the sustainability of these technologies. The semiconductor Cu2ZnSnS4 (Copper Zinc Tin Sulphide) consisting of abundantly available elements promises to be an excellent photovoltaic absorber material. The present study is focused on the growth and characterization of CZTS/ZnS thin film heterostructure suitable for PV applications. Ultrasonic Spray Pyrolysis (USP), a variation of Spray Pyrolysis is a thin film deposition technique where the solution to be sprayed is atomized by ultrasonic frequencies. The details of the USP experimental set up and the deposition principle are presented in the thesis. The active layers of the solar cell, viz. the CZTS absorber layer and ZnS emitter layer were grown by this technique. The metal top contact was deposited using e-beam evaporation. The effects of copper concentration and sodium diffusion on the Cu2ZnSnS4 film properties were investigated. The films have shown preferred orientation along (112) direction confirming kesterite structure. The optical studies revealed that a reduction of copper in the films will bring the band gap energy to 1.5eV, which will match with the solar spectrum. Sodium diffusion in the CZTS films is found to passivate the grain boundaries and enhance the electrical conductivity. These properties render CZTS films as good photovoltaic absorber layers. ZnS has a high band gap and is non toxic unlike CdS. The influences of variation in substrate temperature and spray duration on the ZnS film properties were examined. The optical studies conducted on ZnS films revealed that they are highly transparent in the visible region of the solar spectrum. The films were found to possess a band gap of 3.5 eV. These properties make them potential candidates as solar cell emitter layers. The CZTS/ZnS heterojunction solar cell was fabricated and subjected to electrical characterization in dark and illuminated conditions. A conversion efficiency of 1.16% was achieved for the device.

Cette étude a pour objet d’apporter des éléments de compréhension quant à l’amélioration de la résistance à la corrosion des alliages de ZnMg(Al), en comparaison du Zn, en milieu atmosphérique chloré. Le cheminement de réflexion part de considérations fondamentales et tend vers des conditions réelles d’utilisation. La première étape a consisté à synthétiser et caractériser des films de ZnO dopé Mg et notamment l’évolution de la structure cristalline, la structure électronique, la résistivité, (…) avec le dopage. La pertinence de ces paramètres a ensuite été évaluée et discutée au regard de la stabilité de ces films en solution. Dans un second temps, les produits de corrosion formés, en laboratoire, en présence ou non de chlorures, sur des phases pures de Zn et ZnMg, ont été caractérisés. Les processus physico-chimiques liés à la formation de ces produits ont ensuite été discutés, afin de mettre en lumière le rôle du Mg dans l’amélioration de la résistance à la corrosion. La dernière étape, s’est attachée à caractériser des produits de corrosion formés après 6 mois en milieu naturel, en atmosphère marine, sur des phases pures de Zn et ZnMg, et des revêtements industriel de type ZnMgAl. Les résultats obtenus ont permis de mettre en évidence une meilleure stabilité en solution des films de Zn0.84Mg0.16O en comparaison du ZnO, en corrélation avec une présence accrue de liaisons hydroxyles, une augmentation de la résistivité et de la fonction de travail. Ces trois paramètres sont apparus également pertinents, sur les produits de corrosion formés en laboratoire et naturellement en présence de Mg et de Mg, Al, et corrélés à l’amélioration de la résistance à la corrosion. / The aim of this study was to provide some understanding about the improvement of the corrosion resistance of ZnMg and ZnMgAl alloys in comparison to Zn, in chloride content atmospheric environment, from fundamental considerations gradually towards the actual use of these materials. The first approach consisted in the synthesis and physicochemical characterization of films of magnesium doped zinc oxide and particularly the evolution of parameters such as the crystal structure, the electronic structure (band gap), the resistivity, (…) with doping. The relevance of these parameters was then evaluated and discussed regarding to the stability of these films in a solution of pH 8.4. The second stage focused on the characterization of corrosion products formed in the laboratory with or without chloride, on pure Zn and ZnMg. The physico-chemical processes related to the formation of these products were then discussed to highlight the role of Mg in the improvement of the corrosion resistance of ZnMg alloys in comparison with the Zn. The third and final stage consisted in the characterization of corrosion products formed in marine atmosphere on pure Zn and ZnMg, as well as on industrial coating-type ZnMgAl, after 6 months of exposure. The results obtained in this study showed a better stability in solution of solid solution films of Zn0.84Mg0.16O in comparison with the ZnO, correlated with the increase of hydroxyl bonds, associated with an increase of resistivity and work function. These three parameters appeared also relevant regarding the corrosion products formed naturally in the laboratory and in the presence of Mg and Mg-Al, and correlated with improvement of the corrosion resistance.

The thesis consists of two parts. Part 1 deals with the preparation of thin films and sub-micron powders of complex metal oxides by nebulized spray pyrolysis (NSP) and Part 2 consists of Brillouin scattering studies of solid materials exhibiting interesting phase transitions. The simple technique of NSP has been employed to prepare thin films of A12O3, PbTiO3, Pb(Zr0.5Ti0.5)O3 (PZT) and PbZrO3 on single crystal substrate. The films were characterized by various techniques for their composition, structure, morphology and dielectric properties. Ferroelectric (FE) films of the configuration FE/LaNiO3/SiO2/Si (FE = PbTiO3 and PZT), wherein the LaNiO3 barrier electrode was also deposited on the SiO2/Si substrate by NSP, have been investigated. The films exhibit satisfactory ferroelectric properties. PbZrO3 films deposited on LaNiO3/SiO2/Si substrates show good features, including a reversible AFE ↔ FE transition. Sub-micron particles of TiO2, ZrO2, Pb(Zr0.5Ti0.5)O3, Al2O3, S1O2 and mullite have been prepared by NSP and characterized by various techniques. Brillouin scattering has been used, for the first time, not only to characterize the Peierls transition but also the incommensurate to commensurate transition in the one-dimensional blue bronze, K0.3M0O3. The charge density wave transition in NbSe2 has also been investigated by Brillouin scattering. The charge ordering and antiferromag-netic transitions in single crystals of the rare earth manganates, Nd0.5Ca0.5MnO3 and Pr0.63Ca 0.37MnO3, have been investigated by Brillouin scattering. It is noteworthy that the temperature variation of the Brillouin shift and intensity parallel to that of the magnetization, thereby throwing light on magnetic excitations in charge-ordered state. Brillouin scattering investigations of C60 and C70 films have yielded values of the elastic moduli.

The atmosphere we live in contains various kinds of chemical species, natural and artificial, some of which are vital to our life, while many others are more or less harmful. The vital gases like oxygen, humidity have to be kept at adequate levels in the living atmosphere, whereas the hazardous and toxic gases like hydrocarbons, H2, volatile organic compounds, CO2, CO, NOx, SO2, NH3, O3 etc should be controlled to be under the designated levels. The measurement technology necessary for monitoring these gases has emerged, particularly as organic fuels and other chemicals have become essential in domestic and industrial life. In addition to other applications, environmental pollution monitoring and control has become a fundamental need in the recent years. Therefore, there has been an extensive effort to develop high-performance chemical sensors of small size, rugged construction, light weight, true portability, and with better sensing characteristics such as high sensitivity, fast response and recovery times, low drift, and high degree of specificity. Among the various types of gas sensors studied, solid state gas sensors based on semiconducting metal oxides are well established, due to their advantages over the other types, and hence cover a wide range of applications. However, the widespread application of these sensors has been hindered by limited sensitivity and selectivity. Various strategies have been employed in order to improved the performance parameters of these sensors. This thesis work has two major investigations, which form two parts of the thesis. The first part of this thesis describes the efforts to improve the sensing behaviour of one of the extensively studied metal oxide gas sensors, namely, ZnO, through a novel, ultrasonic-nebulised spray pyrolyis synthesis method, employing an aqueous combustion mixture (NSPACM). The second part of the thesis deals with the ideal of gas detection by optical means through the reversible phase transformation between V2O5 and V6O13 deposited by metalorganic chemical vapor deposition(MOCVD). The introductory chapter I deals with basics of chemical sensors and the characteristic sensing parameters. Different types of gas sensors based on the phenomena employed for sensing are discussed, with an emphasis on semiconducting metal oxide gas sensors. The importance of material selection for solid state gas sensors, depending on the purpose, location, and conditions of operation are discussed, supporting the assertion that semiconducting metal oxides are better suited to fulfill all the requirements of modern gas sensors. Some of the effective methods to improve performance parameters including the influence of grain size, microstructure, and surface doping are described., followed by the motivation of the present thesis. The part I of the thesis is based on the resistive semiconducting metal oxide, where the system investigated was ZnO. Part one comprises Chapters 2, 3 and 4. In Chapter 2, a brief introduction to the material properties of ZnO, followed by various synthesis techniques are discussed. An overview of spray pyrolysis and combustion synthesis is followed by the details of the method employed in the present study, namely NSPACM, which is based on the above two methods, for the formation of ZnO films. A detailed description of the film deposition system built in house is presented, followed by the deposition procedure and the parameters used. Thermal study of the combustion mixture and non-combustion precursor shows the importance of the fuel, along with oxidizer, in forming the film. The films formed using combustion mixture are found to be polycrystalline, whereas films formed without combustion were found to have preferred crystallographic orientation even on an amorphous substrate, which is explained on the basis of minimization of surface energy. The observed unique microstructure with fine crystallite size and porous morphology is attributed to the combustion method employed, which is interesting from the point of view of gas sensing. Chapter 3 concerns the gas sensing study of these ZnO films. The design of the home made gas sensing system is explained in detail. The study of electrode characteristics is followed by the important steps in gas sensing measurements. ZnO gas sensors were mainly studied for their selectivity between aliphatic and aromatic hydrocarbons. The results show two regions of temperature where the sensitivity peaks for aliphatic hydrocarbons, whereas aromatic hydrocarbons show a single sensitive region. This observation can pave the way for imparting selectivity. Possible reasons for the observed behavior are mentioned. Chapter 4 describes the chemical and physical modifications done to ZnO thin films by doping with catalysts, and through the use of x-y translational stage for large-area deposition.. Homogenous distribution of catalysts achieved by the NSPACM synthesis procedure, determined by the x-ray elemental mapping, is discussed. The addition of catalysts improved the sensing both because of catalytic effects and by promoting preferred crystallographic orientation, with Ni addition showing the better effects. The use of the x-y stage in producing the films with high orientation, which improved the gas sensing behavior, is explained. Part II of the thesis comprises Chapters 5,6 and 7, and describes a detailed study of V2O5 and V6O13 thin films deposited by MOCVD for optical sensing of chemical species. In Chapter 5, a brief introduction to chemical vapor deposition is given, followed by the importance of the characteristics of CVD precursors – in particular, the importance of their thermal behavior in film formation. This is followed by the importance of vapor pressure and partial pressure studies in the MOCVD of oxides of a multivalent metal such as vanadium. Various techniques of measuring vapor pressure are listed, followed by the details of the method used in the present study employing rising temperature thermogravimetry, based on the Langmuir equation. Thermogravimetric analysis performed, both at atmospheric as well as at low pressure, using commercial and home made apparatus, respectively is discussed. A detailed description of the home made setup is also presented. Chapter 6 describes the application of the vapor pressure and partial pressure studies to the deposition of films using MOCVD. Here, a detailed description of the vanadium oxide phase diagram and the stability of various phases is presented, which points the importance of precise parameter control during the deposition to obtain pure phases. The details of the CVD setup, followed by the procedure and parameters of deposition, are presented. The films deposited at various deposition temperatures, analyzed using XRD and SEM, are discussed. The effect of temperature on the growth is explained. The effect of vapor pressure is studied by varying the precursor vaporizer temperature, with a growth temperature maintained invariant. The influence of the amount of precursor on film growth, with a particular crystalline orientation and phase content, is explained followed by the description of the deposition of pure phases of V2O5 and V6O13 through the optimization of CVD parameters. Chapter 7 deals with the optical study of the films deposited by the above method. Here, the importance of two phases of vanadium oxide, V2O5 and V6O13, to the proposed gas sensing action, is presented. Their structural similarity in terms of polyhedral arrangement in the ab plane can be the basis of a reversible phase change. The difference in the optical transmittance in two phases forms the basis for the optical method for chemical sensing. The details of the laser-based optical sensing setup, its, design and the detection method, are explained. Studies on hydrocarbon sensing with vanadium, pentoxide films are also presented. The novelty in using reversible chemical transformation of a material system for detection of reducing and oxidizing gases in the ambient gases is discussed. Chapter 8 provides a summary of the present thesis, together with the main conclusions. The work reported in this thesis has been carried out by the candidate as part of the Ph.d training programme. She hopes that this would constitute a worthwhile contribution towards the understanding and subsequent application of ZnO and oxides of vanadium(V2O5 and V6O13) as novel gas sensors which will be useful for environmental protection, as well as for safety in industrial an domestic sectors.

The work deals with the deposition of layers for electrochromic device with different methods. Transparent electrically conductive layer of SnO2 was deposited by pyrolytic decomposition of peroxostannate solution. Hydrogen peroxide in starting solution contributes to the oxidation process of growth layers and to increase the electrical conductivity. Active electrochromic layer of WO3 was electrolytic deposited from the peroxotungstic acid solution. Optimal deposition time and the optimal annealing temperature of deposited layers were found. Passive electrochromic layer of V2O5 was deposited using dip-coating method from peroxovanadate solution. A contribution of solution diluted with distilled water was investigated. Found results were used to construct complete electrochromic device with polymer gel electrolyte.

Metal Oxide (MO)semiconductors are one of the most widely used materials in commercial gas sensor devices. The basic principle of chemoresistive gas sensor operation stems on the high sensitivity of electrical resistance to ambient gaseous conditions. Depending on whether the oxide is "p type" or "n type", the resistance increases (or decrease), when placed in atmosphere containing reducing (or oxidizing) gases. The study of conductometric metal oxide semiconductor gas sensors has dual importance in view of their technological device applications and understanding fundamental MO-gas interactions. Metal oxides based sensors offer high thermal, mechanical and chemical stability. A large number of MOs show good sensitivities to various gases like CO, NOX, SOX, NH3, alcohols and other Volatile Organic Compounds (VOCs). VOCs are very common hazardous pollutants in the environment. Gas sensors are in great demand for their various applications such as food quality control, fermentation industries, road safety, defence, environmental monitoring and other chemical industries. The aim of the study is to explore the possibility of advancements in semiconducting MO based gas sensor devices through tuning microstructural parameters along with chemical dopants or additives. And further to investigate the underlying mechanism of conductometric MO gas sensors. The novel synthesis method employed is based on the solution combustion method coupled with ultrasonically nebulized spray pyrolysis technique. The well studied SnO2 and relatively unexplored Cr2O3 oxide systems are selected for the study. The non-equilibrium processing conditions result in unique microstructure and defect chemistry. In addition, using this technique MO - Reduced Graphene Oxide (RGO) nanocomposite films has also been fabricated and its application to room temperature gas sensor devices is demonstrated. The thesis comprises of seven chapters. the following section describe the summery of individual chapters. The Chapter 1 describes the introduction and background literature of this technology. A brief review of developments in gas sensor technology so far has been enlisted. This chapter also gives a glimpse of applications of MO semiconductors based sensors. The underlying mechanism involved in the sensing reaction and the primary factors influencing the response of a gas sensor device are enlisted. Further in the later part of the chapter focused the material selection criteria, effect of additives/dopants and future prospects of the technology. The end of this chapter highlights the objective and scope of the work in this dissertation. In the Chapter 2 the the materials selection, characterization techniques and particularly the experimental setups used are elaborated. This includes the deposition method used, which is developed in our group and the the in house built gas sensing system including its working principles and various issues have been addressed. The Ultrasonic Nebulized Spray Pyrolysis of Aqueous Combustion Mixture (UNSPACM) is a novel deposition method devised, which is a combination of conventional spray pyrolysis and solution combustion technique. Spray pyrolysis is versatile, economic and simple technique, which can be used for large area deposition of porous films. The intention is to exploit the exothermicity of combustion reaction in order to have high crystallinity, smaller crystallite size with high surface area, which are extremely important in gas sensor design and its efficiency. Further the gas sensing system and its operation are discussed in detail including the advantages of vertical sensing chamber geometry, wider analyte concentration range (ppm to percentage) obtained through vapor pressure data and simultaneous multi sensor characterization allowing better comparison. Here in this work, Chromium oxide (Cr2O3) and Tin oxide (SnO2) are selected as gas sensing materials for this work as a p-type and n-type metal oxide semiconductors respectively. Nevertheless Cr2O3 is a less explored gas sensing material as compared to SnO2, which is also being used in many commercially available gas sensor devices. Thus, studying and comparing gas sensing properties of a relatively novel and a well established material would justify the potential of the novel deposition technique developed. In Chapter 3, the effect of exothermic reaction between oxidizer and fuel, on the morphology, surface stoichiometry and observed gas sensing properties of Cr2O3 thin films deposited by UNSPACM, is studied. An elaborative study on the structural, morphological and surface stoichiometry of chromium oxide films is undertaken. Various deposition parameters have been optimized. An extensive and systematic gas sensing study is carried out on Cr2O3 films deposited, to achieve unique microstructure. The crystallinity and microstructure are investigated by varying the deposition conditions. Further, the effect of annealing in oxygen gas atmospheres on the films was also investigated. The gas sensing properties are studied for various VOCs, in temperature range 200 - 375 oC. The possible sensing mechanism and surface chemical processes involved in ethanol sensing, based on empirical results, are discussed. In chapter 4, the effect of 1% Pt doping on gas sensing properties of Cr2O3 thin films prepared by UNSPACM, is investigated. The chemical analysis is done using x-ray photoelectron spectroscopy to find the chemical state of Pt and quantification is done. The gas sensing is done towards gases like NO2, Methane and Ethanol. The enhancement in sensitivity and remarkable reduction in response as well as recovery times have been modeled with kinetic response analysis to study the variation with temperature as well as concentration. Further the analysis of observations and model fittings is discussed. The Chapter 5 deals with the defects induced ferromagnetism and gas sensing studies SnO2 nanoparticles prepared by solution combustion method. The structural, chemical analysis of as-synthesized and annealed SnO2 nanoparticles reveal gradual reduction in defect concentration of as-prepared SnO2. The findings of various characterization techniques along with optical absorption and magnetic studies to investigate the defect structure of the material are presented. As defects play crucial role in gas sensing properties of the metal oxide material, the defect induced room temperature ferromagnetism in undoped SnO2 has been used as a potential tool to probe the evidence of the defects. Finally a correlation is established between observed room temperature ferromagnetism and gas sensing studies and primary role of defects in gas sensing mechanism over microstructure is realized . The Chapter 6 presents the deposition of SnO2 thin films by UNSPACM method on glass substrates for gas sensing application. The readiness of UNSPACM in making sensor materials with unform dopant distribution is demonstrated in order to improve the sensor performance in terms of response and selectivity. The chemical composition, film morphology and gas sensing studies are reported. The SnO2 is doped with Cr and Pt to enhance the sensing properties of the material. The doped Oxide films are found to show enhancement in sensitivity and improve the selectivity of the films towards specific gases like NO2 and CO. Further in Chapter 7 an effort has been made to overcome the problem of high operating temperature of metal oxide gas sensors through use of Reduced Graphene Oxide (RGO) and metal oxide nanocomposite films. Although RGO shows room temperature response towards many toxic and hazardous gases but it exhibits poor sensor signal recovery. This has been successfully solved by making nanohybrids of RGO and SnO2. It not only improves the sensor signal kinetics but it enhances the sensitivity also. Thus this chapter endeavors towards low power consumption gas sensing devices. The key findings and future aspects are summarized in the Chapter 8.

Currently conventional sources like coal, petroleum and natural gas meet the energy requirements of developing and undeveloped countries. Over a period of time there is high risk of these energy sources getting depleted. Hence an alternate source of energy i.e. renewable energy is the need of the hour. The advantages of renewable energy like higher sustainability, lesser maintenance, low cost of operation, and minimal impact on the environment make the role of renewable energy sources significant. Out of the various renewable energy sources like solar energy, wind energy, hydropower, biogas, tidal and geothermal, usage of solar energy is gradually increasing. Among various solar energy sources, Photovoltaics has dominated over the past two decades since it is free clean energy and availability of abundant sunlight on earth. Over the past few decades, thin film solar cells (TFSC) have gained considerable interest as an economically feasible alternative to conventional silicon (Si) photovoltaic devices. TFSCs have the potential to be as efficient as Si solar cells both in terms of conversion efficiency as well as cost. The advantages of TFSC are that they are easy to prepare, lesser thickness, requires lesser materials, light weight, low cost and opto-electronic properties can be tuned by varying the process parameters. The present study is focused on the fabrication of AgInS2/ZnS heterojunction thin film solar cell. AgInS2 absorber layer is deposited using both vacuum (sputtering/sulfurization) and non-vacuum (ultrasonic spray pyrolysis) techniques. ZnS window layer is prepared using thermal evaporation technique, detailed experimental investigation has been conducted and the results have been reported in this work. The thesis is divided into 6 chapters. Chapter 1 gives general introduction about solar cells and working principle of solar cell. It also discusses thin film solar cell technology and its advantages. Layers of thin film solar cell structure, Significance of each layers and possible materials to be used are emphasized. A detailed overview of the available literature on both AgInS2 absorber layer and ZnS window layer has been presented. Based on the literature review, objectives of the present work are defined. Chapter 2 explains the theory and experimental details of deposition techniques used for the growth of AgInS2 and ZnS films. Details of characterization techniques to study film properties are described in detail. Chapter 3 presents a systematic study of AgInS2 thin films deposited by sulfurization of sputtered Ag-In metallic precursors. Initially, AgInS2 films are deposited by varying the substrate temperature and properties of as-deposited films are characterized. Structural, morphological, electrical and optical properties of AgInS2 films are explained. From these studies, samples with better properties at particular substrate temperature are optimized. By fixing the substrate temperature, deposition time of silver is varied by keeping other deposition conditions same and the properties of films are discussed. It was observed that deposition time of silver doesn’t have much impact on structural properties of AgInS2 films. However, opto-electric properties of AgInS2 films are enhanced. Based on characterization studies, deposition time of silver is optimized. Deposition time of indium is varied by keeping substrate temperature and silver deposition to optimized value. The properties of as-deposited films are discussed. Based on the above studies, the optimized p type films have a band gap of 1.64 eV, carrier concentration of 1013 ions/cm3 and Resistivity of order 103 Ω-cm. Chapter 4 presents a systematic study of AgInS2 thin films deposited by ultrasonic spray pyrolysis. AgInS2 films are deposited by varying the substrate temperature and properties of as deposited films are characterized. Structural, morphological, electrical and optical properties of AgInS2 films are explained. From these studies, samples with better properties at particular substrate temperature are optimized. By fixing the substrate temperature, concentration of silver molarity in the precursor solution is varied by keeping other deposition conditions same and the properties of films are discussed. Structural, optical and electrical properties of AgInS2 films are enhanced with the increase in silver concentration. Based on characterization studies, concentration of silver is optimized. Similarly concentration of indium molarity in the precursor solution is varied and the properties of as-deposited films are discussed. Finally, sulfur molarity in the precursor solution is varied and properties of films are discussed. It was observed that increasing sulfur after certain limit does not have any effect on the properties of the films. Based on the above studies, this method resulted in the films with resistivity of 103 Ω-cm and band gap of 1.64 eV. These films showed a carrier concentration of 1013 ions/cm3. Chapter 5 describes the growth of ZnS films using thermal evaporation technique. Influence of thickness on the properties of ZnS films is explained. Samples with good crystallinity, high transmission, and wider gap are selected for device fabrication. This p type layer showed a band gap of 3.52 eV. Solar cells have been fabricated using the AgInS2 films developed by both sputtering and ultrasonic spray pyrolysis techniques. A maximum cell efficiency of 0.92 percent has been achieved for the cell with 0.950 µm thick sputtered AgInS2 layer and thermally evaporated 42 nm thick ZnS layer. In comparison, the ultrasonic spray pyrolysis deposited films gave an efficiency of 0.54 percent. These values are comparable to those mentioned in a couple of reports earlier. Chapter 6 summarizes the conclusions drawn from the present investigations and scope of future work is suggested.