Spelling suggestions: "subject:"starter/enerator"" "subject:"starter/benerator""
1 |
Design and Analysis of a Tensioner for a Belt-driven Integrated Starter-generator System of Micro-hybrid VehiclesOlatunde, Adebukola Olsanmi 26 February 2009 (has links)
The thesis presents the design and analysis of a Twin Tensioner for a Belt-driven Integrated Starter-generator (B-ISG) system. The B-ISG is an emerging hybrid transmission closely resembling conventional serpentine belt drives. Models of the B-ISG system's geometric properties and dynamic and static states are derived and simulated. The objective is to reduce the magnitudes of static tension in the belt for the ISG-driving phase. A literature review of hybrid systems, serpentine belt drive modeling and automotive tensioners is included. A parametric study evaluates tensioner parameters with respect to their impact on static tensions. Design variables are selected from these for an optimization study. The optimization uses a genetic algorithm (GA) and a hybrid GA. Results of the optimization indicate the optimal system contains spans with static tensions that are significantly lower in magnitude than that of the original design. Implications of the research on future work are discussed in closing.
|
2 |
Design and Analysis of a Tensioner for a Belt-driven Integrated Starter-generator System of Micro-hybrid VehiclesOlatunde, Adebukola Olsanmi 26 February 2009 (has links)
The thesis presents the design and analysis of a Twin Tensioner for a Belt-driven Integrated Starter-generator (B-ISG) system. The B-ISG is an emerging hybrid transmission closely resembling conventional serpentine belt drives. Models of the B-ISG system's geometric properties and dynamic and static states are derived and simulated. The objective is to reduce the magnitudes of static tension in the belt for the ISG-driving phase. A literature review of hybrid systems, serpentine belt drive modeling and automotive tensioners is included. A parametric study evaluates tensioner parameters with respect to their impact on static tensions. Design variables are selected from these for an optimization study. The optimization uses a genetic algorithm (GA) and a hybrid GA. Results of the optimization indicate the optimal system contains spans with static tensions that are significantly lower in magnitude than that of the original design. Implications of the research on future work are discussed in closing.
|
3 |
Control systems for switched reluctance and permanent magnet machines in advanced vehicular electric networksFernando, Weeramundage Udaya Nuwantha January 2012 (has links)
This thesis presents the design and analysis of specialised control systems for switched reluctance (SR) and permanent magnet (PM) machines in vehicular electric applications. Control systems for operation in motoring and power generation are considered for both the types of machines. The SR machine operation considered in this thesis is mainly focused towards the application of aero-engine starter/generators. The control designs for PM machines are formulated considering general fault-tolerant and isolated multiphase PM machines which can be applied in the majority of safety-critical vehicular power and propulsion applications. The SR motoring mode presented in this thesis considers the control design for operation from zero speed to a high speed range, while SR generation mode is confined to the high speed range, such as for the requirements of aero-engine starter/generator operation. This thesis investigates applied control methods for both single-pulse and chopping modes of operation. Classical excitation control versus peak current control and the introduction of a zero-voltage interval are compared for SR motor operation. Optimized excitation control versus two classical forms of excitation control are developed and compared for SR generator operation. Studies include simulation of a 12/8 250kW machine and experimental work on a 6/4 300W machine. The PM motoring and power generation considered in this thesis focuses on a special class of PM machines and drives which are specifically designed for fault-tolerant operation. Optimized control strategies for the operation of PM machines with the parallel H-bridge per-phase converter architecture are investigated. Mathematical modelling of the machine and drive with a consideration of harmonics is presented. The developed control methods are then evaluated by means of finite-element model based simulations of a 125kW five phase surface PM rotor machine and an interior PM rotor machine.
|
4 |
Sensorless control of brushless synchronous starter generator including sandstill and low speed region for aircraft application / Commande sans capteurs mécaniques de la machine synchrone à trois étages à faible vitesse pour une application aéronautiqueMaalouf Haddad, Amira 03 March 2011 (has links)
In More Electric Aircraft, different power system activities are attributed to electrical means such as the start-up of the main engine. In this context, the study of the sensorless control of the Brushless Synchronous Starter Generator (BSSG) that is used to electrically start the main engine is revealed to be a very interesting issue. For long time, the elimination of the mechanical sensor was highly recommended for reliability, cost, weight, integration issues.Hence, this work aims to transpose the results obtained in the research area to an avionic testbench. It presents an adaptive sensorless technique to use when electrically starting the main engine of the aircraft. This is achieved by elaborating three different methods selected depending on the speed of the machine and based on the :- injection of a high frequency signal- use of the back-emf of the Permanent Magnet Generator (PMG)- use of the extended Kalman Filter EKFIn this work, it is shown that the …first method gives good position estimation results from standstill up to 8% of the rated speed. Then, the back-emfs of the PMG are used to detect the position of the BSSG when the speed exceeds the 8% of the rated speed. Good results are observed with this method at medium and high speed.For redundancy reasons, the EKF was also used in this work. Thus, the estimated position can be delivered via two different estimation algorithms in medium and high speed region.The implementation of the algorithm was achieved on an FPGA board since the latter can ensure a very tiny execution time. The fastness of the treatment ensures quasi-instantaneous position estimation and does not practically introduce any phase lag in the position estimation. / Aujourd'hui, l'aviation est en train de vivre des évolutions technologiques concernant surtout l'attribution de différentes fonctionnalités aux équipements électriques et ceci au détriment d'équipements hydrauliques et mécaniques assurant les mêmes fonctionnalités.Dans le cadre de l'avion plus électrique, le démarrage électrique sans capteurs mécaniques de la turbine de l'avion préoccupe les avionneurs de nos jours. Les problèmes introduits par ce capteur ont été identifiés : problèmes de coût et de poids, problèmes de fiabilité et d'intégration.Ce travail présente alors une commande sans capteurs pour la machine synchrone à trois étages à utiliser durant le démarrage électrique de l'avion. Ceci est réalisé avec trois méthodes de détection de la position selon la vitesse de rotation, basées sur :- l'injection d'un signal à haute fréquence- l'utilisation d'un filtre de Kalman étendu FKE- les fém. du PMG (Permanent Magnet Generator) La première méthode donne de bons résultats d'estimation depuis l'arrêt jusqu'à 8% de la vitesse nominale de la machine. Au-delà de cette vitesse, es valeurs des fém. du PMG deviennent assez élevées pour être utilisées dans l'estimation de la position. De bons résultats sont obtenus à moyenne et haute vitesse.Pour des questions de redondance, le FKE est aussi utilisé. Ainsi, la position estimée peut être fournie par l'un des deux algorithmes à moyenne et haute vitesse.L'implémentation de ces algorithmes est réalisée via une carte FPGA étant donné que celui-ci garantit un temps d'exécution. La rapidité de traitement garantit une estimation de la position quasi-instantanée et donc n'introduit pratiquement pas des retards dans l'estimation.
|
5 |
Modeling and Analysis of a Dc Power Distribution System in 21st Century AirliftersLouganski, Konstantin P. 30 October 1999 (has links)
A DC power distribution system (PDS) of a transport aircraft was modeled and analyzed using MATLAB/Simulink software. The multi-level modeling concept was used as a modeling approach, which assumes modeling subsystem of the PDS at three different levels of complexity. The subsystem models were implemented in Simulink and combined into the whole PDS model according to certain interconnection rules. Effective modeling of different scenarios of operation was achieved by mixing subsystem models of different levels in one PDS model. Linearized models were obtained from the nonlinear PDS model for stability analysis and control design.
The PDS model was used to examine the system stability and the DC bus power quality under bidirectional power flow conditions. Small-signal analysis techniques were employed to study stability issues resulting from subsystem interactions. The DC bus stability diagram was proposed for predicting stability of the PDS with different types of loads without performing an actual stability test based on regular stability analysis tools. Certain PDS configurations and operational scenarios leading to instability were identified. An analysis of energy transfer in the PDS showed that a large energy storage capacitor in the input filter of a flight control actuator is effective for reduction of the DC bus voltage disturbances produced by regenerative action of the actuator. However, energy storage capacitors do not provide energy savings in the PDS and do not increase its overall efficiency. / Master of Science
|
6 |
Commande robuste à haute performance sans capteur de position d'alterno-démarreurs à grande vitesse avec un fort couple à l'arrêt pour les avions plus électriques / Robust sensorless control of high-speed Starter/Generators with high starting torque for the More Electric AircraftBeciu, Andreea-Livia 11 October 2018 (has links)
Les avionneurs expriment le besoin de développement de l’avion plus « électrique ». Cela se traduit par des besoins nouveaux en matière de systèmes de motorisation électrique, en termes de puissance à fournir et de partage de ressources matérielles en vue de minimiser la masse embarquée et les coûts. Parmi les études en cours sur l’évolution des machines tournantes, un intérêt particulier porte sur le développement des alterno-démarreurs de type machines synchrones sans balais et à plusieurs étages (BSSG). Celles-ci sont susceptibles de fournir un fort couple lors des phases de démarrage des réacteurs auxquelles elles sont associées. Pour ce faire, la connaissance, à tout moment, de la position du rotor est essentielle. Cependant, l'ajout d’un capteur dédié impacte la conception de la machine, rajoutant du volume, du câblage et augmentant le coût. La réalisation d'une commande dite « sensorless » permettrait de s'affranchir de l'utilisation d'un tel capteur et de simplifier le design des alterno-démarreurs.A partir d'une modélisation fine de la machine, cette thèse étudie les conditions dans lesquelles une telle commande est réalisable et analyse plusieurs techniques permettant d'y parvenir. Une nouvelle méthode d'estimation de la position du rotor, spécifique aux BSSG est proposée, puis illustrée avec des résultats expérimentaux. Cette technique est basée sur le traitement des composantes harmoniques existantes naturellement au stator de la machine et permet l'estimation de la position à l'arrêt et à très basse vitesse. Afin d'étendre l'estimation sur toute la plage de vitesse, une étude d'estimation de position par un observateur d'état à base du modèle complet de la machine en considérant les harmonique injectés (ou existantes) dans les courants du stator est proposée. Cet observateur peut s’appliquer à la machine synchrone à trois étages mais aussi à toute machine synchrone. Dans cette étude, son fonctionnement est illustré sur une machine synchrone à aimants permanents. / The aircraft manufacturers express the need to develop a more "electric" aircraft. This brings forward new requirements for the electric drive systems in terms of increasing the available on-board power and resource sharing in order to optimize the overall mass and cost. Among the ongoing studies on the evolution of motor drives, a particular interest is given to the development of multi-level brushless synchronous starter/generators (BSSG). These drives are likely to provide the high torque required to start-up the reactors to which they are associated. For this purpose, the knowledge, at any time, of the rotor position is essential. However, adding a dedicated sensor impacts on the design of the machine, increasing volume, cabling needs and cost. For this purpose, investigating on “sensorless” control laws will permit to avoid using such a sensor and to simplify the design of the Starter/Generators.Using a fine modelling of the machine, this work studies the conditions of feasibility for sensorless control and analyzes several techniques for this purpose. A new method of estimation of the shaft-position, particular to the BSSG architecture is proposed and then illustrated with experimental results. This technique is based on the processing of the existing harmonic components naturally in the stator of the machine and allows the estimation of the position at standstill and the very low speed. To extend the estimation to the whole speed range, a study of position estimation using a state observer using the complete model of the machine considering the knowledge of the existing (or injected) harmonic components in the stator currents is proposed. This observer can be applied to the brushless synchronous starter/generator but also on generic synchronous machines. In this study, its performance is illustrated on a permanent magnet synchronous machine.
|
7 |
Contribution à la prise en compte des aspects thermiques des machines électriques dans un environnement mécatronique / Contribution to taking into consideration thermal aspects of electric machines in mechatronics environmentAssaad, Bassel 11 December 2015 (has links)
Les machines électriques jouent un rôle très important dans la conversion d'énergie dans plusieurs applications et domaines. Les contraintes thermiques jouent ainsi un rôle indispensable dans la conception des machines électriques de plus en plus petites et performantes. En effet, la performance des machines électriques est limitée par les températures maximales admissibles dans certaines zones critiques telles que le bobinage, les aimants permanents et les roulements. Deux approches principales peuvent être utilisées pour étudier le comportement thermique de la machine: la méthode nodale ou le circuit à constantes localisées ou les modèles numériques. Dans notre étude, nous proposons d'appliquer la méthode nodale sur une machine électrique intégrée dans un environnement mécatronique complexe. Le modèle thermique développé de la machine est ainsi présenté avec ses différents éléments. En effet, un modèle précis dépend fortement de plusieurs paramètres thermiques tels que les coefficients d'échange convectif, les conductances de contact, les conductivités équivalentes du bobinage, et autres paramètres. En conséquence, des techniques d'analyse de sensibilité sont ensuite appliquées sur le modèle thermique pour identifier les paramètres d'influence significative sur les températures de la machine ainsi que pour la réduction de ce modèle. Ensuite, nous appliquons deux méthodologies d'identification des paramètres thermiques incertains sont développées et appliquées afin de recaler le modèle thermique de la machine. Cette étape permet la validation de ce modèle par rapport à des mesures thermiques sur une machine synchrone à aimants permanents internes installée sur un banc de caractérisation de machine électriques. Finalement, nous intégrons le modèle recalé dans une approche système mécatronique comportant les lois de commande de la machine ainsi que son convertisseur. Ceci permettra ainsi d'étudier l'influence de la température d'une machine électrique sur le système mécatronique complet. / Electric machines play an important role in power conversion in several applications and fields. With the increasing demand for designing lighter and more efficient machines and optimizing the existing structures, thermal analysis becomes a necessary; in fact, the performance of electric machines islimited by the allowable temperatures in many critical components like windings, permanent magnetsand bearings. Two main approaches can be employed in order to study the machine thermal behavior : the lumped parameter thermal network (LPTN) or numerical models. Considering low-computationtime-consuming and the possibility to be integrated in a mechatronics system design, the LPTN method is considered in our study. The latter is mainly applied on electric machine integrated in a complex mechatronics environment. The thermal network is presented along with the definition of the principal elements constituting this network. In fact, an accurate and reliable network strongly depends on many critical parameters like heat transfer coefficients, interface gaps, impregnation goodness, among others. For this reason, different sensitivity analysis techniques are carried out in order to, first, identify the significance of uncertainties in the evaluation of these parameters on machine temperatures and second, to reduce the thermal network. Next, we propose two optimization algorithm-based identification methodologies in order to calibrate results of the thermal network with measured temperatures obtained from a test-bench of a permanent magnet based integrated starter-generator machine. The calibrated model is then integrated in a mechatronics system consisting of an electric model of the electric machine, along with its control strategy and the power converter. This final study allows us to evaluate the impact of the machine temperature rise on the mechatronic system.
|
Page generated in 0.0739 seconds