Electromagnetic transient and dynamic modeling and simulation studies are presented for a StatCom-SMES compensator in power systems. The transient study aims to better understand the transient process and interaction between a high power/high voltage SMES coil and its power electronics interface, dc-dc chopper. The chopper is used to attach the SMES coil to a StatCom. Following the transient study, the integration of a StatCom with SMES was explored to demonstrate the effectiveness of the combined compensator in damping power oscillations. The transient simulation package PSCAD/EMTDC has been used to perform the integrated modeling and simulation studies. A state of the art review of SMES technology was conducted. Its applications in power systems were discussed chronologically. The cost effective and feasible applications of this technology were identified. Incorporation of a SMES coil into an existing StatCom controller is one of the feasible applications, which can provide improved StatCom operation, and therefore much more flexible and controllable power system operation. The SMES coil with the following unique design characteristics of 50MW (96 MW peak), 100 MJ, 24 kV interface has been used in this study. As a consequence of the high power/ high voltage interface, special care needs to be taken with overvoltages that can stress the insulation of the coil. This requires an investigation of transient overvoltages through a detailed modeling of SMES and its power electronics interface. The electrical model for the SMES coil was developed based on geometrical dimensions of the coil. The interaction between the SMES coil and its power electronics interface (dc-dc chopper for the integration to StatCom) was modeled and simulated to identify transient overvoltages. Transient suppression schemes were developed to reduce these overvoltages. Among these are MOV implementation, surge capacitors, different configurations of the dc-dc chopper. The integration of the SMES coil to a StatCom controller was developed, and its dynamic behavior in damping oscillations following a three-phase fault was investigated through a number of simulation case studies. The results showed that the addition of energy storage to a StatCom controller can improve the StatCom-alone operation and can possibly reduce the MVA rating requirement for the StatCom operating alone. The effective location selection of a StatCom-SMES controller in a generic power system is also discussed. / Ph. D.

This research focused on the characterization of organosilicone surfactants and their effects on sulfonylurea herbicide activity. The project included efficacy tests, rainfastness studies in the greenhouse, radiotracer studies on herbicide uptake, fluorescent dye studies on surface deposition, and various measurements of physico-chemical properties. In measuring physico-chemical properties, a logistic dose response relationship was found between adjuvant concentration and contact angle on parafilm. An AsymSigR relationship existed between adjuvant concentration and surface tension for all the adjuvants. The organosilicones, Silwet L-77, Silwet 408, and Sylgard 309, and Kinetic (a blend of an organosilicone with a nonionic surfactant) gave equilibrium surface tension values around 20 dyne/cm and showed great spreading ability on the foliage of velvetleaf. With the conventional adjuvants, Agri-Dex, methylated soybean oil, Rigo oil concentration, and X-77, and Dyne-Amic (a blend of an organosilicone with a crop oil concentrate), surface tension was rarely below 28 dyne/cm and spreading ability was limited on velvetleaf. In addition, the organosilicone surfactant and Kinetic also lowered dynamic surface tension, which may improve droplet retention on leaf surfaces. The differences in physico-chemical properties between Kinetic and Dyne-Amic confirmed that carefully electing a co-adjuvant for an organosilicone blend is critical to avoid antagonism with trisiloxane molecules and retain the unique physico-chemical properties of organosilicone in the blends. Studies involving structurally-related organosilicones showed that the end structure in the trisiloxane hydrophilic group has little or no effect on surface tension, contact angle, spread pattern, herbicide uptake and translocation, and efficacy of primisulfuron on velvetleaf. It may be suggested that there is not a strict requirement to purify the end structure during the synthesis process, which is time consuming and expensive. When 14C-primisulfuron was combined with organosilicones or the blends, the uptake of 14C at 1 or 2 h after herbicide application was significantly higher than when combined with conventional adjuvants in velvetleaf. In the greenhouse, organosilicone surfactants greatly increased the rainfastness of primisulfuron in velvetleaf. The effect was immediate and dramatic, even when simulated rainfall was applied 0.25 h after treatment. In addition, herbicide efficacy on marginally susceptible weed species, velvetleaf and barnyardgrass, was significantly increased. A very complicated relationship exists between herbicides and adjuvants. The enhancement effects of adjuvants are often herbicide specific, weed species specific, and even environment specific. No one type of adjuvant functions well in all circumstances. Therefore, there is a need to understand the properties and functions of each class of adjuvants and locate the 'right' niche for each individual adjuvant. / Ph. D.

The chemical resistance of glass is an important property for many applications. This property has been extensively studied for many types of glass under static conditions (no liquid is removed during the experiment). There has been little research conducted on the effects of additional stimuli on the dissolution of glass. For this research lithium disilicate was leached in deionized water at multiple temperatures while microwave radiation, ultrasonication or flow conditions were also applied to the system. These results were then compared to static baseline to determine if these stimuli would cause any change to the mechanisms and kinetics of the reaction. It was determined that for the experimental conditions used there was little to no change in dissolution when 2.45 GHz microwave radiation instead of conventional methods was used to heat the reaction. Results from ultrasonication found that samples that experienced erosion showed an increase in dissolution with an increase in dissolution following heavier erosion. This was thought to be due to both an increase in the surface area of the sample to volume of solution (SA/V) ratio (erosion would modify the surface area and release small particulates) and the accelerated removal of the depleted layer due to erosion. Stereoscopic reconstruction was used to semi-quantitatively measure the change in surface area. Regions that experienced minor erosion showed a 3-6% increase in surface area while those that experienced heavy erosion showed a 29-35% increase in surface area. Due to inconsistencies in the size of the eroded area it was not possible to determine the effects of power intensity with this research. Flow dissolution showed similar trends in concentration and different trends for the total normalized mass loss (TNL) to previously published research on more complex glasses. The elemental concentration initially increased before reaching a peak and decreasing to steady state. This peak was thought to be caused by the combination of flow, increasing thickness in the depleted layer, and an initial fluctuation in the forward reaction rate due to changes in pH. For the lithium disilicate glass used in this research both the elemental concentration and the TNL increased with increasing temperature and decreasing flow rate (silica dissolution was an exception as it did not show any change in TNL due to flow). All experimental conditions were shown to achieve steady state (dC/dt~0) by the seventh day of leaching. The contrast in the observed TNL trends between lithium disilicate and more complex glasses was thought to be due to differences in reaction rates and the presence of an additional surface layer in the complex glasses due to precipitation. Microscopy of the leached glass showed that surface features introduced during grinding (scratch lines and microcracks) were preferentially leached and grew in size and number visible during dissolution. A semi-quantitative model was created using stereoscopic reconstruction to describe the preferential leaching of the microcracks as there was little available discussion found in literature outside of associating the growth of these features with localized network dissolution. In this model the microcracks experience preferential dissolution leading to a change in size and shape. The SA/V ratio inside the crack would be much larger than the bulk system (calculated to initially be ~768,000cm-1 compared to the bulk's 0.1cm-1). This would cause massive acceleration in the initial ion exchange, raising the pH of the solution which would in turn cause network dissolution to occur much faster inside the crack. Based on static experiments on lithium disilicate frit (SA/V of 1,010cm-1) the pH inside the crack would jump to above 11 in minutes. As the crack grows, the SA/V ratio inside it would decrease (largest cracks were found to have a ratio ~100,000cm-1). The accelerated leaching caused by these features could have a noticeable effect on the dissolution results. In addition to the accelerated leaching inside a crack, the size of the depleted layer under the crack would be different from the bulk glass. / Doctor of Philosophy / The chemical resistance of glass is an important property for many applications. This property has been extensively studied for many types of glass under static conditions where no liquid was removed and temperature was the major variable. For this research lithium disilicate was leached in deionized water at multiple temperatures while the additional stimuli of microwave radiation, ultrasonication or flow conditions were also applied to the system. The question that this research addressed was how does the aqueous dissolution of glass change when a system is exposed to these additional stimuli? Although glasses are subjected to these stimuli in many everyday applications, their influence on dissolution has not been studied extensively. Lithium disilicate glass was selected because it contains components used in many commercial glasses, has sufficient reactivity in water to allow experiments to be completed in a reasonable time, and because its mechanisms for dissolution under static conditions were well known. Glass is frequently selected to be the container when microwaves are used to heat food or materials. Flow is an important part of many applications involving glass including the storage of nuclear waste glass, glass-lined tanks used in the chemical industries, in the use of glass in the human body (bioglass and dental crowns), and in typical window and laboratory glasses where intermittent aqueous contact and runoff may occur. Examining how cavitation via ultrasonication can be controlled to either minimize or maximize element extraction is important, with the removal of rare earth elements from fly ash being one example.

The overall energy consumption of portable devices has been projected to triple over the next decade, growing to match the total power generated by the European Union and Canada by 2025. The rise of the internet-of-things (IoT) and ubiquitous and embedded computing has resulted in an exponential increase in such devices, wherein projections estimate that 50 billion smart devices will be connected and online by 2020. In order to alleviate the associated stresses placed on power generation and distribution networks, a holistic approach must be taken to conserve energy usage in electronic devices from the component to the circuit level. An effective approach to reduce power dissipation has been a continual reduction in operating voltage, thereby quadratically down-scaling active power dissipation. However, as state-of-the-art silicon (Si) complimentary metal-oxide-semiconductor (CMOS) field-effect transistors (FETs) enter sub-threshold operation in the ultra-low supply voltage regime, their drive current is noticeable degraded. Therefore, new energy-efficient MOSFETs and circuit architectures must be introduced. In this work, tunnel FETs (TFETs), which operate leveraging quantum mechanical tunneling, are investigated. A comprehensive investigation detailing electronic materials, to novel TFET device designs, to memory and logic digital circuits based upon those TFETs is provided in this work. Combined, these advances offer a computing platform that could save considerable energy and reduce power consumption in next-generation, ultra-low voltage applications. / Ph. D.

Yes / This paper proposes a new index to determine the static voltage stability of the load buses in a power network for certain operating conditions and hence identifies load buses which are close to voltage collapse. The proposed index is formulated from the quadratic equation derived from a two-bus network and is computed using the apparent power and the line impedance. The proposed index shows how far the load buses from their voltage stability limit and hence the most sensitive bus can be identified according to maximum loadability. 14 bus IEEE reliability test system is used to study the performance of the proposed index for its validity. A comparison is also made between proposed index and some other indices found in the literature. The results are discussed and key conclusion drawn.

Physically unclonable functions are increasingly used as security primitives for device identification and anti-counterfeiting. However, PUFs are associated with noise and bias which in turn affects its property of reliability and predictability. The noise is corrected using fuzzy extractors, but the helper data generated during the process may cause leakage in min-entropy due to the bias observed in the response. This thesis offers two optimization techniques for PUF based protocols. The first part talks about the construction of a secure enrollment solution for PUFs on a low-end resource-constrained device using a microcontroller and a secure networked architecture. The second part deals with the combined optimization of min-entropy and error-rate using symbol clustering techniques to improve the reliability of SRAM PUFs. The results indicate an increase in min-entropy without much effect on the error rate but at the expense of PUF size. / Master of Science

This project, completed in collaboration with Piktiv AB, aimed to develop an automated surface hole-filling feature for static meshes in Unreal Engine 4.27, with the goal of making repaired surfaces visually indistinguishable from their surrounding areas. The solution was primarily designed to address holes that arose from, but were not limited to, the use of Reduction Settings within Unreal Engine on static meshes. The functionality encompassed four key stages: boundary detection, where all holes on the mesh were identified; triangulation, which involved patching the hole using vertices from the boundary; refinement, entailing the addition of vertices and triangles to the patched area to mimic the density of the surrounding surface; and fairing, which smoothed the patched surface. Additionally, the project introduced a straightforward method for determining the texture coordinates of newly added vertices and a technique for ensuring that triangle normals correctly faced outward from the mesh. The Static Mesh Hole Filler, as implemented, demonstrates efficiency in filling an arbitrary amount of small, planar holes, which commonly result from polygon reduction using Reduction Settings in Unreal Engine. However, this function falls short in preserving unique texture details and maintaining the curvature of surfaces when dealing with larger holes. This limitation necessitates users to seek alternative methods for effectively repairing the mesh.

The objective of this thesis is to examine the effect of dynamic induction machine modeling and polynomial static load modeling on the stability of electric power systems and to compare the results with those obtained using constant impedance or constant current load models. A least-squares curve fit algorithm is developed and used in modeling static and quasi-static loads as a function of the bus voltage. A dynamic model for the induction machine which accounts for rotor electrical and mechanical transients is incorporated into the solution algorithm. A test system is analyzed under a variety of loading conditions. The effect of the induction motor .load inertia constants on the system stability are also examined. Plots of load bus voltages during the transient stability period are included. / Master of Science

The present work describes the finite element (FE) modeling and dynamic response of lightweight, deployable shelters (tent) to large external blast loads. Flexible shelters have been used as temporary storage places for housing equipments, vehicles etc. TEMPER Tents, Small Shelter System have been widely used by Air Force and Army, for various field applications. These shelters have pressurized Collective Protection System (CPS), liner, fitted to the frame structure, which can provide protection against explosives and other harmful agents. Presently, these shelter systems are being tested for the force protection standards against the explosions like air-blast. In the field tests carried out by Air Force Research Laboratory, it was revealed that the liner fitted inside the tent was damaged due to the air blast explosion at some distant from the structure, with major damage being on the back side of the tent. The damage comprised of tearing of liner and separation of zip seals. To investigate the failure, a computational approach, due to its simplicity and ability to solve the complex problems, is used. The response of any structural form to dynamic loading condition is very difficult to predict due to its dependence on multiple factors like the duration of the loading, peak load, shape of the pulse, the impulse energy, boundary conditions and material properties etc. And dynamic analysis of shell structures pose even much greater challenge. Obtaining solution analytically presents a very difficult preposition when nonlinearity is considered. Therefore, the numerical approach is sought which provide simplicity and comparable accuracy. A 3D finite element model has been developed, consisting of fabric skin supported over the frames based on two approaches. ANSYS has been used for obtaining the dynamic response of shelter against the blast loads. In the first approach, the shell is considered as a membrane away from its boundaries, in which the stress couple is neglected in its interior region. In the second approach, stress coupling is neglected over the whole region. Three models were developed using Shell 63, Shell 181 and Shell 41. Shell 63 element supports both the membrane only and membrane-bending combined options and include stress stiffening and large deflection capabilities. Shell 181 include all these options as Shell 63 does and also, accounts for the follower loads. Shell 41 is a membrane element and does not include any bending stiffness. This element also include stress stiffening and large deflection capabilities. A nonlinear static analysis is performed for a simple plate model using the elements, Shell 41 and Shell 63. The membrane dominated behavior is observed for the shell model as the pressure load is increased. It is also observed that the higher value of Young's modulus (E) increases the stresses significantly. Transient analysis is a method of determining the structural response due to time dependent loading conditions. The full method has been used for performing the nonlinear transient analysis. Its more expensive in terms of computation involved but it takes into account all types of nonlinearities such as plasticity, large deflection and large strain etc. Implicit approach has been used where Newmark method along with the Newton-Raphson method has been used for the nonlinear analysis. Dynamic response comprising of displacement-time history and dynamic stresses has been obtained. From the displacement response, it is observed that the first movement of the back wall is out of the tent in contrast to the other sides whose first movement is into the tent. Dynamic stresses showed fluctuations in the region when the blast is acting on the structure and in the initial free vibration zone. A parametric study is performed to provide insight into the design criteria. It is observed that the mass could be an effective means of reducing the peak responses. As the value of the Young's Modulus (E) is increased, the peak displacements are reduced resulting from the increase in stiffness. The increased stiffness lead to reduced transmitted peak pressure and reduced value of maximum strain. But a disproportionate increase lead to higher stresses which could result in failure. Therefore, a high modulus value should be avoided. / Master of Science

Weigh-in-Motion (WIM) systems have improved the process of collecting data from heavy vehicles on the U.S. highway system and enforcing the laws that govern vehicle weights. The benefits of WIM are reaped by everyone from highway designers and voernments officials, to truck drivers and transportation industry owners. The data collected by WIM devices is essential for proper pavement design, developing pavement management systems, weight enforcement strategies, modeling traffic improvement projects, and predicting load-related distresses and performance. While WIM offers many advantages over its alternative, static weighing, the technology is limited by problems associated with the accuracy of its measurements. Weigh-in-Motion systems that lack accuracy require vehicles to travel slower and can result in higher queues, longer delays, and potential hazards. For these reasons, WIM system performance must be improved in order to adequately serve its purpose. In order to evaluate WIM system performance and determine what vehicle characteristics have the most affect on it, two systems in the Commonwealth of Virginia were evaluated. The first system was an in-service WIM system at the Troutsville weigh station on I-81. The Troutsville station had bending plate WIM scales located in both the northbound and southbound directions. The second system in a newly developed WIM system manufactured by Omni Weight Corporation (OWC) and was installed at the Virginia Smart Road for evaluation. The OWC scale is a completely sealed and buried system that has ten strain gauge sensors in its interior. Evaluation of both scales was performed by conducting a number of test runs under varying load conditions. Testing at Troutsville was performed using four different test vehicles with multiple loads on each. Variation in load was achieved by loading the test vehicles with various numbers of concrete Jersey Walls. Testing on the OWC scale was performed using only two test vehicles while varying the speed, load, tire pressure, and direction of travel over the scale. The study showed that the scales at the Troutsville weigh station yielded 10% error or less on only 77% of the tests, not complying with the required 95% set forth by ASTM E-1318. In comparison, using the manufacturer's processed data for the OWC scale yielded only 18% of its tests with 10% error or less, far below the ASTM standard. A model was developed to re-calculate the axle weights using the raw sensor data from the OWC scale; and an evaluation of the accuracy of this data showed that the OWC scale performed much better. While compliance with the ASTM standards was still not achieved, it rose from 18% to 71% of the tests having 10% error or less. Repeatability of the Troutsville scales and OWC scales was found to be comparable. / Master of Science