Microwave communication devices have become ubiquitous in the past decade. As an increasing number of systems compete for spectrum, guard bands have shrunk to increase bandwidth efficiency. The frequency behaviour of microwave devices is affected by thermal expansion. In order to avoid interference with adjacent bands, microwave components must exhibit high temperature-stability in most communications applications. Thermally stable materials can be used to construct temperature-stable components. However, this approach requires an expensive mass and cost trade-off. Temperature compensated aluminum resonators and filters provide major advantages in cost and mass. This work proposes that a compensating tuning screw with a temperature-dependent effective length be constructed by mounting a bimetallic compensator at the end of a mounting screw. This so-called bimetal tuning-screw can be used to produce temperature-compensated resonators and filters. There are several advantages to this approach. Compensation can be tuned by adjusting the depth of the bimetal, simply by adjusting the mounting screw. Since there are no moving parts inside the cavity or filter, and the bimetal can be plated, there are no additional sources of passive intermodulation. Also, this design is simple to implement for waveguide designs in general. In order to compensate for temperature drift, it is useful to quantify uncompensated drift. Temperature drift for a lossless linearly expanding RF component is derived from Maxwell's equations. For the lossy case, it is demonstrated that the resulting formula is approximately true, and that the quality of this approximation is excellent for practical levels of temperature range and thermal expansion. Experimental results are provided that demonstrate bimetal compensation under uniform-temperature conditions for a single aluminum resonator. Measured drift of the compensated resonator is -0.38 ppm/°C, compared to -23 ppm/°C for an uncompensated resonator. Measured drift for a bimetal-compensated 4-pole filter prototype is 2.35 ppm/°C. A method for adjusting compensation for a filter is also provided. Multiphysics simulations are used to examine power handling for bimetal-compensated filters. It is demonstrated that power-handling can be improved by reducing the effective length of the compensator to improve heat conduction to the cavity or filter.

The microstructural evolution and mechanical properties at elevated temperatures of a recently fabricated fine-grained AA6xxx aluminium sheet were evaluated and compared to the commercially fabricated sheet of the same alloy in the T4P condition. The behaviour of the fine-grained and T4P sheets was compared at elevated temperatures between 350°C and 550°C, as well as room temperature. Static exposure to elevated temperatures revealed that the precipitate structure of the fine-grained material did not change extensively. The T4P material, however, underwent extensive growth of precipitates, including a large amount of grain boundary precipitation. At room temperature, the T4P material deformed at much higher stresses than the FG material, but achieved lower elongations. Deformation at elevated temperatures revealed that the fine-grained material achieved significantly larger elongations to failure than the T4P material in the temperature range of 350°C-450°C. Both materials behaved similarly at 500°C and 550°C. Above 500°C, the grain size was greatly reduced in the T4P material, and only a slightly increased in the fine-grained material. At temperatures above 450°C, the elongation to failure in both materials generally increased with increasing strain-rate. The poor performance of the T4P material at low temperatures was attributed to the precipitate characteristics of the sheet, which lead to elevated stresses and increased cavitation. The deformation mechanism of both materials was found to be controlled by dislocation climb, accommodated by the self diffusion of aluminium at 500°C and 550°C. The deformation mechanism in the fine-grained material transitioned to power law breakdown at lower temperatures. At 350°C to 450°C, the T4P material behaved similarly to a particle hardened material with an internal stress created by the precipitates. The reduction in grain size of the T4P material after deformation at 500°C and 550°C was suggested to be caused by dynamic recovery/recrystallization. The role of a finer grain-size in the deformation behaviour at elevated temperatures was mainly related to enhanced diffusion through grain boundaries. The differences in the behaviour of the two materials were mainly attributed to the difference in the precipitation characteristics of the materials.

Transport measurements and fabrication of superconductor-exchange spring magnet-superconductor systems

In order to explore how electrons and holes in 2D semiconductors behave at 3He temperatures under millimeter wave irradiation, we developed a new probe and measurement technique. Our samples are specially grown high-mobility GaAs/AlGaAs 2D electron or hole systems that have been modulation doped with Si or C respectively and etched into Hall bars. We also use microwave irradiation waveguide techniques to probe edge magnetoplasmons in 2D electron systems and find that the periodic resistance oscillations in the magnetic field are independent of the length between the leads measured. This demonstrates that the propagation of edge states is a non-local effect, contrary to previously established research. We confirm microwave induced resistance oscillations using a newly developed probe that delivers microwaves from a frequency generator down to the sample via a coax line and coplanar waveguides. Due to the low frequency range (2 -- 40 GHz) and high irradiation powers available, we are able to observe microwave induced resistance oscillations and newly revealed fractional microwave induced resistance oscillations. The probe that we develop for this new measurement makes previously unattainable non-Faraday as well as Faraday irradiation geometries accessible. In addition to measuring quantum transport, it also allows us to measure the transmission of microwaves across the sample. We establish a differential measurement technique that instantaneously removes the background signal leaving only the transmission from the 2D system, also reducing the preparation time required. This is accomplished with a gated high-mobility sample prepared to allow for microwaves to be irradiated from the back. The advantage of this new technique is that it accommodates any gated/polished sample which can be mounted on the specially designed sample holder. From this arrangement we are able to measure the cyclotron resonance transmission minima of both the 2D electron and hole systems. We can then use the known values for the effective mass and cyclotron time constant as a confirmation that our new probe can successfully make the expected measurements.

The aim of this Project is to study the influence of high return temperatures in district heating on the costs for heat and power production in a CHP plant.When the temperatures of the water coming back to the heating plant are so high, the overall performance of heat and power production is decreased and, consequently, also the production costs. Along the project, the influence of this temperature on the different parts of a CHP plant are analysed as well as the economical impact it has. At the same time, some general impacts on the entire network are mentioned.   A real network is used in this project, and it is the net of district heating in Gävle (Sweden), and the most of the study is focus in its bigger combined heat and power production plant (CHP), called Johannes.

Abstract The behavior for MoSi2 based high temperature heating elements for resistive heating has been examined in elevated temperature and low oxygen content environment. MoSi2 spontaneously forms a protective SiO2 scale at high temperature if the amount of oxygen in the ambient atmosphere is sufficient according to the following reaction: 5MoSi2 + 7O2(g)  7SiO2 + Mo5Si3 If the oxygen content at a specific temperature is too low, SiO(g) is more stable than SiO2 and the following reaction will occur instead: 2SiO2  2SiO(g) + O2(g) Then surface will be Si-deplated and finally, the base material will be exposed. Si and Mo will oxidize and degas from the surface as SiO and MoO3 with severe diameter reduction of the heating element as a result. It is therefore of high interest to find the relationship between the maximum element temperature and the oxygen content in the ambient atmosphere to be able to fully exploit the potential of the heating elements and also to aid and help diagnose customer complaints.   After 14 full scale tests in a custom made atmospheric furnace, the following equation could be calculated: p(O2) = 1.748·100.01677·T·log(e)-10 The equation gives the minimum oxygen content at a specified temperature. The equation is based on 100 hours tests at atmospheric pressure, gas flow rate of 4 liter per minute, varying temperature and varying oxygen content. Nitrogen has been used as carrier gas for the oxygen.

In this report a novel low temperature synthesis approach of CdS nanocrystals is described starting from well known precursors, Cd(SA) and TOP-S, in a ligand system of aliphatic long chain alcohols. A one-pot synthesis approach is applied using a laboratory microwave heating source. The resulting CdS nanocrystals exhibit an absorbance with a pronounced fine-structure, a photoluminescence with a very high ratio between the band gap peak and the defect peak and a fluorescence quantum yield of 33%. Different synthesis approaches have been investigated by changing heating rate, temperature, precursor concentration and chain length of the aliphatic alcohol ligand as well as chain length of the Cadmium precursor. It was found that small changes in the heating rate do not affect the reaction. Changing the reaction temperature between 200°C and 160°C has no visible effects on the quality of the resulting CdS nanocrystals. At 140°C the nanoparticles experience a significant drop in quality, probably because there is a major change in the growth mechanism of the nanocrystals at that low temperature. At 100°C and 120°C the creation of so-called CdS nanoclusters is observed, and a growth mechanism towards nanocrystals based on cluster aggregation is suggested. For the synthesis of high quality nanoparticles it was found that a ratio of 1:25 between precursor and aliphatic alcohol is preferable as well as a ratio of 1:1 between the two precursors. If the chain length of both the precursors and the alcohol is short, the reaction rate is enhanced. If the chain length is too short the nanocrystals grow very fast and the size distribution gets broad, the photoluminescence intensity decreases and the ratio between band gap luminescence and defect luminescence decreases. The best Cd-precursor was found to be Cd-Laurate and the most suitable ligand evaluated was Tetradecanol.

Continuous casting is a casting process that produces steel slabs in a continuous manner with steel being poured at the top of the caster and a steel strand emerging from the mould below. Molten steel is transferred from the AOD converter to the caster using a ladle. The ladle is designed to be strong and insulated. Complete insulation is never achieved. Some of the heat is lost to the refractories by convection and conduction. Heat losses by radiation also occur. It is important to know the temperature of the melt during the process. For this reason, an online model was previously developed to simulate the steel and ladle wall temperatures during the ladle cycle. The model was developed as an ODE based model using grey box modeling technique. The model’s performance was acceptable and needed to be presented in a user friendly way. The aim of this thesis work was basically to design a GUI that presents steel and ladle wall temperatures calculated by the model and also allow the user to make adjustments to the model. This thesis work also discusses the sensitivity analysis of different parameters involved and their effects on different temperature estimations.

Weather data are huge. Traditional visualization techniques are limited to show temperature trends. Pixel-based approaches could be used to visualize the huge amount of weather data and in process show the temperature trends. A prototype using this approach is built to make temperature data more understandable in changing trends. It is implemented using a 2D representation and many popular interaction techniques. It is a lightweight and reusable tool to visualize temperatures.

Microwave communication devices have become ubiquitous in the past decade. As an increasing number of systems compete for spectrum, guard bands have shrunk to increase bandwidth efficiency. The frequency behaviour of microwave devices is affected by thermal expansion. In order to avoid interference with adjacent bands, microwave components must exhibit high temperature-stability in most communications applications. Thermally stable materials can be used to construct temperature-stable components. However, this approach requires an expensive mass and cost trade-off. Temperature compensated aluminum resonators and filters provide major advantages in cost and mass. This work proposes that a compensating tuning screw with a temperature-dependent effective length be constructed by mounting a bimetallic compensator at the end of a mounting screw. This so-called bimetal tuning-screw can be used to produce temperature-compensated resonators and filters. There are several advantages to this approach. Compensation can be tuned by adjusting the depth of the bimetal, simply by adjusting the mounting screw. Since there are no moving parts inside the cavity or filter, and the bimetal can be plated, there are no additional sources of passive intermodulation. Also, this design is simple to implement for waveguide designs in general. In order to compensate for temperature drift, it is useful to quantify uncompensated drift. Temperature drift for a lossless linearly expanding RF component is derived from Maxwell's equations. For the lossy case, it is demonstrated that the resulting formula is approximately true, and that the quality of this approximation is excellent for practical levels of temperature range and thermal expansion. Experimental results are provided that demonstrate bimetal compensation under uniform-temperature conditions for a single aluminum resonator. Measured drift of the compensated resonator is -0.38 ppm/°C, compared to -23 ppm/°C for an uncompensated resonator. Measured drift for a bimetal-compensated 4-pole filter prototype is 2.35 ppm/°C. A method for adjusting compensation for a filter is also provided. Multiphysics simulations are used to examine power handling for bimetal-compensated filters. It is demonstrated that power-handling can be improved by reducing the effective length of the compensator to improve heat conduction to the cavity or filter.