This thesis deals with fabrication and optimization of lead-free piezoceramics based on (Ba0,85Ca0,15Zr0,1Ti0,9)O3 (BCZT). The BCZT precursor powder was synthesized by sol-gel method. Dependence of relative density, microstructure, phase structure and piezoelectric properties on the sintering temperature in a range from 1300–1500 °C was studied on disc shaped samples, which were prepared by cold isostatic pressing (CIP) using pressure of 700 MPa. It was found, that sintering at 1300 and 1350 °C leads to ceramics with fine-grain microstructure, which exhibits poor piezoelectric properties (d*33 = 50 pC·N1 and 65 pC·N1, respectively). The highest value of piezoelectric charge coefficient was obtained by sintering at 1500 °C (d*33 = 390 pC·N1). Furthermore, BCZT thick films were prepared by tape casting. The composition of the ceramic slurry was optimized and various sintering techniques were tested to obtain completely flat films of BCZT ceramics. The correct sintering configuration has not been found. The least deformation of the films was achieved when the samples were sintered hung on the ZrO2 rod. The highest value of d*33 for BCZT films was measured when the sample was sintered at 1400 °C with the dwell time for 4 h (d*33 = 340 pC·N1).

Since the development of thick film hybrid microelectronic processing, there has been a need for methods to adjust for tighter tolerances for electrical components through a trimming process. Components/elements, as produced, show a tolerance of the order of ±10% due to the variability of the screen printing process associated with film curing conditions. The methods that have arisen from this need encompass a variety of technologies and techniques. The usefulness of each method is based on its operation, flexibility, repeatability, and post-trim effects on the resistor's reliability. The work in this thesis concerns the laser trimming of resistor components to a tight tolerance. It is the objective of this thesis to address the performance of an Nd:YAG laser operation and interface with a computer. The first task involves a computer hardware system to be interfaced to the laser control system, this task includes both design and implementation. The second task consists of a software operating environment to be flowcharted, written, and tested. The third task involves the computer interface driving the laser in the process of trimming resistor components using different types of cuts. The trimmed resistor performance is evaluated as part of the study. / Master of Science

High Temperature Superconductors (HTS) materials are ideal for many electrical applications. These applications include high speed interconnects, microwave structures and transmission lines, as well as electronic devices that utilize the unique electrical and magnetic properties of these materials. To date, the use of high temperature superconductors has been limited to a narrow range of substrate materials, due to the reactive nature of these superconductors. Chemical reactions between the substrate and the superconductor cause decomposition of the superconductor into an insulator. The researcher has developed a thick film system that allows the production of high quality HTS films on reactive substrates, such as alumina (Al203). This system utilizes a thick film buffer layer of pure silver in combination with thick film superconductors composed of Y1Ba2~CU30X. The silver buffer layer is designed to prevent contact between the substrate and the superconductor, thereby eliminating chemical reactions between the two materials. The development as well as the comprehensive characterization of these films is described in this work. / Master of Science

Os materiais de estrutura perovskita compreendem um vasto grupo de compostos cuja estrutura na sua forma mais simples pode ser representada pela fórmula química ABO3. Uma das principais vantagens que a estrutura perovskita apresenta é o alto grau de flexibilidade em acomodar uma grande variedade de átomos nos sítios A e B, permitindo um maior controle de suas propriedades físicas e químicas bem como a manutenção de sua estrutura básica, mesmo para altas concentrações de átomos substituintes. Devido estas propriedades, estes materiais têm sido aplicados com sucesso como capacitores, varistores, fotoeletrodos, memóriasferroelétricas e sensores de gases. Nas últimas décadas, tem sido reportada a utilização do titanato de estrôncio (SrTiO3, ST) na forma de filmes finos e espessos como sensor de gás oxigênio em altas temperaturas (>500 °C). Recentemente, foi mostrado que o titanato de estrôncio dopado com Fe apresentava uma excelente sensibilidade ao gás ozônio. Entretanto, neste trabalho, somente uma composição foi caracterizada e nem todas as propriedades importantes em relação a esta aplicação foram completamente exploradas. Neste contexto, esta tese de doutorado teve como objetivo verificar o efeito da substituição do átomo de estrôncio pelo lantânio e do titânio pelo Ferro no composto SrTiO3 na forma de pó e filmes finos nanoestruturados com a finalidade de verificar o efeito destas substituições nas propriedades sensoras do material. Inicialmente, com o objetivo de avaliar a influência da adição de La na estrutura do composto ST, amostras na forma de pó do sistema Sr1-xLaxTiO3.(SLT) foram preparadas através do método dos precursores poliméricos. Posteriormente, pelo mesmo método, foram sintetizadas amostras do sistema SrTi1-xFexO3 (STF) e Sr1-XLaxTi1-yFeyO3 (SLTF). A partir das amostras na forma de pó e na forma de solução, filmes finos e espessos foram respectivamente obtidos através das técnicas de deposição por feixe de elétrons (EBD) e spin-coating (SC). As amostras nanoestruturadas na forma de pó e na forma de filmes foram caracterizadas por difração de raios X, espectroscopia de absorção de raios X (XANES) na borda K do Ti e do Fe e espectroscopia de fotoelétrons excitados por raios X (XPS). A análise morfológica foi realizada através das técnicas de microscopia eletrônica de varredura (MEV) e microscopia de força atômica (MFA). As amostras do sistema STF e SLTF na forma de filmes finos foram avaliadas em relação à sensibilidade aos gases O3, NO2, NH3 e CO. Os resultados indicaram que os filmes do sistema SLTF depositados pela técnica de deposição por feixe de elétrons apresentam uma maior sensibilidade ao gás ozônio, enquanto o filme de mesma composição depositado pelo método de spin-coating apresentou uma melhor estabilidade e tempo de recuperação em relação a este mesmo gás. / The perovskite structure materials comprise a large group of compounds with the structure in simple form can be represented by the ABO3. chemical formula. The main advantage that the perovskite structure presents is the high degree of flexibility to accommodate a wide variety of atoms in sites A and B, allowing a greater control of physical and chemical properties of the material, maintaining its structure even for a high concentrations of substituent\'s. Due to these properties, these materials have been successfully applied as capacitors, varistors, photoelectrodes, ferroelectric memories and gas sensors. In the last decade, strontium titanate (SrTiO3, ST) in the form of thin and thick films have been reported as oxygen gas sensor at higher temperatures (> 500 °C). Recently, strontium titanate doped with Fe was used as the first ozone sensor. However, the work was carried out only with a certain composition and some important properties for this application have not been fully exploited. In this context, this PhD thesis aimed to the synthesis of strontium titanate system in powder form and nanostructured thin films with the substitution of Sr for La and Ti for Fe. In order to verify the effect of these substitutions in material properties initially Sr1-xLaxTiO3 (SLT) samples were prepared in powder form by the polymeric precursor method in order to evaluate the influence of the addition of La in the structure of the compound ST. Subsequently, samples were synthesized from SrTi1-x Fex O3 (STF) and Sr1-XLaxTi1-yFeyO3 (SLTF) systems through the polymeric precursors, which were used for the deposition of thin and thick films, which were respectively obtained through electron beam deposition techniques (EBD) and spin-coating (SC). Samples in the form of nanostructured powder and thin films were characterized by X-ray diffraction, X-ray absorption spectroscopy (XANES) at Ti and Fe K-edges and by X-ray photoelectron spectroscopy (XPS). Morphological analysis was performed using the scanning electron microscopy (SEM) and atomic force microscopy (AFM) techniques. The STF and SLTF samples in a thin film form were evaluated towards their sensitivity to O3, NO2, NH3 and CO gases. The results indicated that SLTF films deposited by electron beam deposition technique exhibit higher sensitivity to ozone gas. However the same composition deposited by spin-coating showed a better stability and recovery time relative to the same gas.

Avec la demande sans cesse renouvelée de matériaux éco-compatibles pour l’électronique de demain, les polymères conducteurs se sont imposés comme une alternative intéressante aux matériaux déjà existants. Ils doivent leur popularité principalement à leurs propriétés électriques, optoélectroniques, thermo-chromiques, luminescentes et mécaniques, couplées à leur bonne processabilité et leur faible impact environnemental. Parmi eux, le poly(3,4-ethylenedioxythiophene) (PEDOT) est certainement le plus connu est le plus utilisé. De nombreuses études se sont focalisées sur l’optimisation de sa conductivité électrique et des progrès remarquables ont été réalisés. Cependant, la compréhension fine de la relation structure/propriétés de ce matériau reste à élucider. C’est ainsi que dans le cadre de cette thèse nous avons décidé de plusieurs objectifs qui sont (1) la synthèse de PEDOT hautement conducteurs à structure contrôlée et optimisée, (2) l’étude des propriétés électriques, structurales et de transport électroniques dans ces PEDOT, (3) l’étude de leurs propriétés thermoélectriques et (4) l’étude de leur stabilité sous différentes conditions afin de valider leurs potentielles applications. Ainsi, après une revue de la littérature sur le PEDOT, nous étudions l’amélioration de la conductivité électrique du PEDOT:OTf et du PEDOT:Sulf, qui atteint dorénavant des valeurs à hauteur de 5400 S cm-1. Différentes techniques de caractérisation nous ont permis de mener une étude exhaustive de leurs propriétés électriques et structurales ainsi que des mécanismes de transport électronique qui en découlent. Nous nous sommes ensuite intéressés à deux de leurs propriétés thermoélectriques, l’effet Joule et l’effet Seebeck, le premier pour des applications en chauffage et le deuxième pour la récupération d’énergie. L’utilisation pour la première fois du PEDOT comme film chauffant flexible transparent est d’ailleurs présentée. On démontre par exemple que PEDOT:Sulf présente une résistance carrée de 57 Ω sq-1 pour 87.8 % de transparence et qu’une température de 138 °C peut être atteinte lorsqu’on applique 12 V. Cette thèse se conclut sur l’étude de la stabilité de nos matériaux de PEDOT sous différentes atmosphères ainsi que l’étude des mécanismes de dégradation. / With the rising demand of flexible, low cost and environmentally friendly materials for future technologies, organic materials are becoming an interesting alternative to already existing inorganic ones. Organic photovoltaics, organic light emitting diodes, organic field effect transistors, organic thermoelectricity, organic transparent electrodes are all evidences of how organic materials are sought for tomorrow. Materials which can fulfill the requirements specifications of future technologies are conducting polymers, which owe their popularity to their outstanding electrical, optoelectronic, thermochromic, lighting and mechanical properties. Moreover, they exhibit good processability even on flexible substrates and low environmental impact. Poly(3,4-ethylenedioxythiophene) (PEDOT) is certainly the most known and most used conducting polymer because it is commercially available and shows great potential for organic electronics. Studies dedicated to PEDOT films have led to high conductivity enhancements. However, an exhaustive understanding of the mechanisms governing such enhancement is still lacking, hindered by the semi-crystalline nature of the material itself. In such a context, this thesis has four objectives which are (1) the synthesis of PEDOT materials with an optimized and controlled structure to enhance the electrical properties, (2) the thorough characterization of the as-synthesized PEDOT in order to understand the charge transport mechanisms, (3) the study of their thermoelectric properties and (4) the study of their stability under different environments and stresses. Thus, after a literature review on PEDOT materials, we present the enhancement of the electrical conductivity of PEDOT:OTf and PEDOT:Sulf up to 5400 S cm-1 via a structure and dopant engineering, and then thoroughly study their electrical and electronic transport properties. Subsequently, two thermoelectric properties of PEDOT are investigated, namely its resistive Joule heating ability and its Seebeck effect, for both heating and energy harvesting applications. A novel application of PEDOT as flexible transparent heater is demonstrated in the first case. PEDOT:Sulf for example exhibited a sheet resistance of 57 Ω sq-1 at 87.8 % transmittance and reached a steady state temperature of 138 °C under 12 V bias. Finally, this thesis is concluded with the ageing and stability of our PEDOT based materials under different environmental stresses. While PEDOT is stable under mild conditions, heavy degradations can occur under harsh conditions. The degradation mechanisms are then investigated in this last part.

Grâce à son faible coût, sa grande résolution et son absence d’effet ionisant, l’imagerie ultrasonore haute fréquence est devenue une technique usuelle pour les applications médicales telles que l’imagerie de l’œil, de la peau ou du petit animal. Cette méthode repose sur la capacité de matériaux piézoélectriques à créer des ondes acoustiques hautes fréquences dans les tissus à explorer. Les dispositifs qui opèrent ces conversions électromécaniques sont appelés transducteurs ultrasonores et doivent délivrer des fréquences de résonance de plus de 20 MHz, nécessitant l’intégration des films piézoélectriques ayant une épaisseur de quelques dizaines de micromètres. La fabrication de tels matériaux pour les transducteurs mono- et multi-éléments est toujours difficile suivant les procédés choisis. Dans ce manuscrit, le procédé de dépôt par électrophorèse a été étudié. Il permet le dépôt de films épais sur de nombreux substrats de formes complexes en vue de la fabrication de transducteurs hautes fréquences. Dans cette thèse, il est clairement montré que l’électrophorèse est un procédé simple prometteur et performant pour préparer des films épais homogènes sans défaut avec des propriétés fonctionnelles élevées pour la réalisation de transducteurs hautes fréquences (40 MHz). / Thanks to its relatively low cost, high resolution and absence of ionizing radiations, high frequency ultrasonic imaging is becoming a popular technique for medical applications such as eyes, skin or small animal. It relies on the ability of piezoelectric materials to generate high frequency ultrasonic waves in the scanned media. Ultrasonic transducers are used to perform these electromechanical conversions and operated at resonant frequencies over 20 MHz. For this, piezoelectric layers of few tens of micrometers thick are required. Such thicknesses for single element transducers, and even more for multi-element transducers, is difficult to deliver due to limitations of current fabrication process. In the present dissertation we addressed the electrophoretic deposition (EPD) technique that enables deposition of piezoelectric thick films on various complex-shaped substrates. A procedure to prepare high frequency transducers by EPD was developed. In the dissertation it was demonstrated that EPD is a promising process to prepare homogeneous thick-film structures without significant defects. The procedure allowed obtaining high electromechanical performance transducers using a simple and low cost process.

Os materiais de estrutura perovskita compreendem um vasto grupo de compostos cuja estrutura na sua forma mais simples pode ser representada pela fórmula química ABO3. Uma das principais vantagens que a estrutura perovskita apresenta é o alto grau de flexibilidade em acomodar uma grande variedade de átomos nos sítios A e B, permitindo um maior controle de suas propriedades físicas e químicas bem como a manutenção de sua estrutura básica, mesmo para altas concentrações de átomos substituintes. Devido estas propriedades, estes materiais têm sido aplicados com sucesso como capacitores, varistores, fotoeletrodos, memóriasferroelétricas e sensores de gases. Nas últimas décadas, tem sido reportada a utilização do titanato de estrôncio (SrTiO3, ST) na forma de filmes finos e espessos como sensor de gás oxigênio em altas temperaturas (>500 °C). Recentemente, foi mostrado que o titanato de estrôncio dopado com Fe apresentava uma excelente sensibilidade ao gás ozônio. Entretanto, neste trabalho, somente uma composição foi caracterizada e nem todas as propriedades importantes em relação a esta aplicação foram completamente exploradas. Neste contexto, esta tese de doutorado teve como objetivo verificar o efeito da substituição do átomo de estrôncio pelo lantânio e do titânio pelo Ferro no composto SrTiO3 na forma de pó e filmes finos nanoestruturados com a finalidade de verificar o efeito destas substituições nas propriedades sensoras do material. Inicialmente, com o objetivo de avaliar a influência da adição de La na estrutura do composto ST, amostras na forma de pó do sistema Sr1-xLaxTiO3.(SLT) foram preparadas através do método dos precursores poliméricos. Posteriormente, pelo mesmo método, foram sintetizadas amostras do sistema SrTi1-xFexO3 (STF) e Sr1-XLaxTi1-yFeyO3 (SLTF). A partir das amostras na forma de pó e na forma de solução, filmes finos e espessos foram respectivamente obtidos através das técnicas de deposição por feixe de elétrons (EBD) e spin-coating (SC). As amostras nanoestruturadas na forma de pó e na forma de filmes foram caracterizadas por difração de raios X, espectroscopia de absorção de raios X (XANES) na borda K do Ti e do Fe e espectroscopia de fotoelétrons excitados por raios X (XPS). A análise morfológica foi realizada através das técnicas de microscopia eletrônica de varredura (MEV) e microscopia de força atômica (MFA). As amostras do sistema STF e SLTF na forma de filmes finos foram avaliadas em relação à sensibilidade aos gases O3, NO2, NH3 e CO. Os resultados indicaram que os filmes do sistema SLTF depositados pela técnica de deposição por feixe de elétrons apresentam uma maior sensibilidade ao gás ozônio, enquanto o filme de mesma composição depositado pelo método de spin-coating apresentou uma melhor estabilidade e tempo de recuperação em relação a este mesmo gás. / The perovskite structure materials comprise a large group of compounds with the structure in simple form can be represented by the ABO3. chemical formula. The main advantage that the perovskite structure presents is the high degree of flexibility to accommodate a wide variety of atoms in sites A and B, allowing a greater control of physical and chemical properties of the material, maintaining its structure even for a high concentrations of substituent\'s. Due to these properties, these materials have been successfully applied as capacitors, varistors, photoelectrodes, ferroelectric memories and gas sensors. In the last decade, strontium titanate (SrTiO3, ST) in the form of thin and thick films have been reported as oxygen gas sensor at higher temperatures (> 500 °C). Recently, strontium titanate doped with Fe was used as the first ozone sensor. However, the work was carried out only with a certain composition and some important properties for this application have not been fully exploited. In this context, this PhD thesis aimed to the synthesis of strontium titanate system in powder form and nanostructured thin films with the substitution of Sr for La and Ti for Fe. In order to verify the effect of these substitutions in material properties initially Sr1-xLaxTiO3 (SLT) samples were prepared in powder form by the polymeric precursor method in order to evaluate the influence of the addition of La in the structure of the compound ST. Subsequently, samples were synthesized from SrTi1-x Fex O3 (STF) and Sr1-XLaxTi1-yFeyO3 (SLTF) systems through the polymeric precursors, which were used for the deposition of thin and thick films, which were respectively obtained through electron beam deposition techniques (EBD) and spin-coating (SC). Samples in the form of nanostructured powder and thin films were characterized by X-ray diffraction, X-ray absorption spectroscopy (XANES) at Ti and Fe K-edges and by X-ray photoelectron spectroscopy (XPS). Morphological analysis was performed using the scanning electron microscopy (SEM) and atomic force microscopy (AFM) techniques. The STF and SLTF samples in a thin film form were evaluated towards their sensitivity to O3, NO2, NH3 and CO gases. The results indicated that SLTF films deposited by electron beam deposition technique exhibit higher sensitivity to ozone gas. However the same composition deposited by spin-coating showed a better stability and recovery time relative to the same gas.

A busca por membranas com propriedades adequadas a separação de gases em escala industrial tem levado a modificação e sIntese de polImeros de engenharia, com objetivo de obter membranas com propriedades adequadas. Uma das modificaçoes que tem se apresentado promissora é a inserção de grupos sulfônicos em polImeros comerciais. Espera-se que o polImero sulfonado apresente um aumento na permeação de gases polares, em relação a gases apolares, devido a sua estrutura mais polar e flexIvel. Neste contexto, o objetivo do presente trabalho é a sIntese e caracterização de membranas de poli(éter imida) sulfonada para a permeação de gases. Um planejamento experimental foi desenvolvido, em diferentes condiçoes reacionais de temperatura, tempo e excesso de um dos reagentes (ácido acético), para a sIntese de poli(éter imida) sulfonada (SPEI). Através deste planejamento, constatou-se que as variáveis que mais influenciam o grau de sulfonação são a temperatura e o tempo. O polImero com o maior grau de sulfonação, determinado por capacidade de troca iônica (IEC= 92 mEq H+/g), foi utilizado para o preparo da membrana de SPEI, obtida pela técnica de inversão de fase por evaporação do solvente, utilizando-se clorofórmio como solvente. Este filme foi caracterizado a partir das seguintes análises: espectroscopia de infravermelho (FTIR), calorimetria diferencial de varredura (DSC), análise termogravimétrica (TGA) e microscopia eletrônica de varredura (MEV), a fim de avaliar a influência da inserção do grupo sulfônico na matriz polimérica. O espectro de infravermelho de SPEI apresentou bandas relacionadas as vibraçoes assimétricas em 1240 cm-1 (ligação O=S=O), ligação simétrica em 1171 cm-1 (O=S=O) e ligação S-O entre 1010-1024 cm-1. Isto indica a presença de grupos sulfônicos. A análise de DSC foi realizada entre 150-250C. Nesta faixa, não foram observadas alteraçoes na temperatura de transição vItrea (Tg) do polImero modificado (217C). Acredita-se que a decomposição do grupo sulfona aconteça antes da temperatura atingir o Tg do polImero. Esta suposição é confirmada na análise de TGA. As imagens de MEV mostraram que foram obtidos filmes livres de poros e defeitos. A membrana da SPEI foi utilizada no ensaio de permeaçao dos gases 02, N2 e C02, a fim de determinar a permeabilidade e seletividade da membrana. As permeabilidades encontradas para o gas oxigênio foram de 0,76 barrer para a PEI e 0,46 barrer para a SPEI. A seletividade do dióxido de carbono em relaçao ao oxigênio aumentou de 3,5, na membrana de PEI, para 4,83, na membrana de SPEI. Em relaçao ao nitrogênio, as permeabilidades medidas foram 0,064 barrer e 0,043 barrer, para a PEI e para a SPEI, respectivamente, enquanto a seletividade em relaçao ao C02 aumentou de 41,1 para 55,5. Estes resultados indicam que o efeito de sorçao predominou devido ao aumento das interaçöes moleculares, reduzindo assim o volume livre, o que tornou a membrana sulfonada mais compacta, com permeabilidade menor e maior seletividade. Estes resultados corroboram com a premissa de que a sulfonaçao é um processo promissor para o desenvolvimento de membranas mais eficientes. / The search for membranes with suitable properties for gas separation in industrial scale has led to the modification and synthesis of engineering polymers with the purpose of obtaining membranes with superior properties. 0ne of the modifications that have been considered promising is the insertion of sulfonic groups in commercial polymers. Due to its structure more polar and flexible, it is expected that the sulfonated polymer present an increase in polar gas permeation in relation to nonpolar gases. In this context, the objective of this work is the synthesis and characterization of membranes of poly (ether imide) sulfonated for the permeation of gases. An experimental design was developed in different reaction conditions of temperature, time and an excess of one of the reagents (acetic acid), for the synthesis of poly (ether imide) sulfonated, SPEI. Through this planning, it was found that the variables that most influenced the degree of sulfonation are temperature and time. The polymer with the highest degree of sulfonation, by ion exchange capacity (IEC = 92 mEq H+ I g), was used to prepare SPEI membrane obtained by the technique of solvent evaporation, using chloroform. This film was characterized from the following analysis: infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and scanning electron microscopy (SEM) to evaluate the influence of insertion of the sulfonic group in the polymer matrix. The infrared spectrum showed bands of SPEI related to asymmetric vibrations at 1240cm- 1 (S = 0 = 0), in symmetric stretch at 1171 cm-1 (0 = S = 0) and S0 stretch between 1010-1024cm-1. This indicates the presence of sulfonic groups. The DSC analysis was carried out between 150-250C. In this range, there are no significant changes in glass transition temperature of the modified polymer (217C). It is believed that the decomposition of the sulfone group occurs before the temperature reaches the Tg of the polymer. This assumption is confirmed in the TGA analysis. The images of SEM showed that films were obtained free of pores and defects. The membrane SPEI obtained by the technique of solvent evaporation, was used for testing permeation of gases 02, N2 and C02 in order to determine the permeability and selectivity of the membrane. The permeabilities found for oxygen were 0.76 barrer for PEI and 0.46 barrer for SPEI. The selectivity of carbon dioxide relative to oxygen increased from 3.5 to 4.83. Regarding nitrogen, the permeability measurements were 0.064 barrer and 0.043 barrer for the PEI and the SPEI, respectively, while the selectivity relative to C02 increased from 41.1 to 55.5. These results indicate that the predominant effect of sorption due to increased molecular interactions, thus reducing the free volume, made the membrane sulfonated more compact with lower permeability and higher selectivity. These results agree with the premise that the sulfonation is a promising process for the development of more efficient membranes.

Les matériaux ferroélectriques présentant une permittivité diélectrique élevée et de faibles pertes diélectriques présentent un grand intérêt pour la réalisation de condensateurs et le stockage de l'énergie électrique. Les propriétés structurales et diélectriques influencent les paramètres ferroélectriques tels que la polarisation maximale du matériau Pm et la polarisation rémanente Pr sous l'effet d'un champ électrique appliqué Em. Ce mémoire propose d'étudier les propriétés structurales, diélectriques et ferroélectriques des céramiques dérivées de BaTiO₃ (BT) et SrTiO₃ (ST) ainsi que des films épais PVDF pur et composites tels que PVDF/BT et PVDF/BZT. Les céramiques ont été synthétisées par la méthode de la réaction solide et le procédé sol-gel. La substitution dans les sites-A ou les sites-B du matériau BaTiO₃ avec des cations tels que Ca ²⁺, Sr²⁺ and Zr⁴⁺ réduit la densité d'énergie électrique stockée Wd et augmente l'efficacité de stockage énergétique η. La céramique BaZr₀.₅Ti₀.₅O₃ (BZT0.5) présente l'efficacité de stockage énergétique la plus élevée (η=75%). La substitution dans les sites-A du matériau SrTiO₃ avec 40% de cations Ca²⁺ diminue la permittivité diélectrique (ε'∽200), mais cette permittivité est cependant plus stable sur une large gamme de fréquence [100 Hz-1 GHz]. La céramique Sr₀.₆Ca₀.₄TiO₃ préparée par voie sol-gel présente la densité d'énergie électrique stockée la plus élevée (Wd=0.149 J/cm³) sous l'action d'un champ électrique maximal élevé (Em=105 kV/cm). Les films épais à base de polymère PVDF ont été synthétisés par Spin-Coating. La permittivité diélectrique des films épais PVDF pur augmente avec l'apaisseur du film. L'incorporation de particules BT et BZT0.15 dans la matrice polymère PVDF augmente la permittivité diélectrique des films composites PVDF/BT (ε'=32 pour 30% de particules BT) et PVDF/BZT0.15 (ε'=32 pour15% de particules BZT). / Ferroelectric materials with a high dielectric permittivity and low dielectric losses are very attractive for the realization of capacitors and for electrical energy storage. To improve the electrical energy density Wd, the structural and dielectric properties influence the ferroelectric parameters such as the maximum polarization Pm and the remanent polarization Pr under an applied electric field Em. This manuscript proposes to study the structural, dielectric and ferroelectric properties of ceramics derived from BaTiO₃ (BT) and SrTiO₃ (ST) as well as pure PVDF thick films and composites such as PVDF/BT and PVDF/BZT. The ceramics were synthesized by the solid state reaction reaction route and the sol-gel process. The subsitution in the A-sites or B-sites of the BaTiO₃ material with cations such Ca²⁺, Sr²⁺ and Zr⁴⁺ reduces the electrical energy density Wd and increases the energy storage efficiency η. The ceramic BaZr₀.₅Ti₀.₅O₃ (BZT0.5) has the highest energy storage efficiency (η=75%). The substitution in the A-sites of SrTiO₃ material with 40% of Ca²⁺ cations reduces the dielectric permittivity (ε'∽200), but is more stable over a wide frequency range [100 Hz -1 GHZ]. The Sr₀.₆Ca₀.₄TiO₃ ceramic prepared by sol-gel process has the highest electrical energy density (Wd = 0.149 J/cm³) under an electrical field Em = 105 kV/cm. The PVDF thick films were synthesized by Spin-Coating. The dielectric permittivity of pure PVDF thick films increases when increasing the thickness. The addition of BT and BTZ0.15 particles in the PVDF polymer matrix increases the dielectric permittivity of the composite PVDF/BT thick films (ε'=32 for 30% of BT particles) and PVDF/BZT0.15 ones (ε'=32 for 15% of BZT particles).

A busca por membranas com propriedades adequadas a separação de gases em escala industrial tem levado a modificação e sIntese de polImeros de engenharia, com objetivo de obter membranas com propriedades adequadas. Uma das modificaçoes que tem se apresentado promissora é a inserção de grupos sulfônicos em polImeros comerciais. Espera-se que o polImero sulfonado apresente um aumento na permeação de gases polares, em relação a gases apolares, devido a sua estrutura mais polar e flexIvel. Neste contexto, o objetivo do presente trabalho é a sIntese e caracterização de membranas de poli(éter imida) sulfonada para a permeação de gases. Um planejamento experimental foi desenvolvido, em diferentes condiçoes reacionais de temperatura, tempo e excesso de um dos reagentes (ácido acético), para a sIntese de poli(éter imida) sulfonada (SPEI). Através deste planejamento, constatou-se que as variáveis que mais influenciam o grau de sulfonação são a temperatura e o tempo. O polImero com o maior grau de sulfonação, determinado por capacidade de troca iônica (IEC= 92 mEq H+/g), foi utilizado para o preparo da membrana de SPEI, obtida pela técnica de inversão de fase por evaporação do solvente, utilizando-se clorofórmio como solvente. Este filme foi caracterizado a partir das seguintes análises: espectroscopia de infravermelho (FTIR), calorimetria diferencial de varredura (DSC), análise termogravimétrica (TGA) e microscopia eletrônica de varredura (MEV), a fim de avaliar a influência da inserção do grupo sulfônico na matriz polimérica. O espectro de infravermelho de SPEI apresentou bandas relacionadas as vibraçoes assimétricas em 1240 cm-1 (ligação O=S=O), ligação simétrica em 1171 cm-1 (O=S=O) e ligação S-O entre 1010-1024 cm-1. Isto indica a presença de grupos sulfônicos. A análise de DSC foi realizada entre 150-250C. Nesta faixa, não foram observadas alteraçoes na temperatura de transição vItrea (Tg) do polImero modificado (217C). Acredita-se que a decomposição do grupo sulfona aconteça antes da temperatura atingir o Tg do polImero. Esta suposição é confirmada na análise de TGA. As imagens de MEV mostraram que foram obtidos filmes livres de poros e defeitos. A membrana da SPEI foi utilizada no ensaio de permeaçao dos gases 02, N2 e C02, a fim de determinar a permeabilidade e seletividade da membrana. As permeabilidades encontradas para o gas oxigênio foram de 0,76 barrer para a PEI e 0,46 barrer para a SPEI. A seletividade do dióxido de carbono em relaçao ao oxigênio aumentou de 3,5, na membrana de PEI, para 4,83, na membrana de SPEI. Em relaçao ao nitrogênio, as permeabilidades medidas foram 0,064 barrer e 0,043 barrer, para a PEI e para a SPEI, respectivamente, enquanto a seletividade em relaçao ao C02 aumentou de 41,1 para 55,5. Estes resultados indicam que o efeito de sorçao predominou devido ao aumento das interaçöes moleculares, reduzindo assim o volume livre, o que tornou a membrana sulfonada mais compacta, com permeabilidade menor e maior seletividade. Estes resultados corroboram com a premissa de que a sulfonaçao é um processo promissor para o desenvolvimento de membranas mais eficientes. / The search for membranes with suitable properties for gas separation in industrial scale has led to the modification and synthesis of engineering polymers with the purpose of obtaining membranes with superior properties. 0ne of the modifications that have been considered promising is the insertion of sulfonic groups in commercial polymers. Due to its structure more polar and flexible, it is expected that the sulfonated polymer present an increase in polar gas permeation in relation to nonpolar gases. In this context, the objective of this work is the synthesis and characterization of membranes of poly (ether imide) sulfonated for the permeation of gases. An experimental design was developed in different reaction conditions of temperature, time and an excess of one of the reagents (acetic acid), for the synthesis of poly (ether imide) sulfonated, SPEI. Through this planning, it was found that the variables that most influenced the degree of sulfonation are temperature and time. The polymer with the highest degree of sulfonation, by ion exchange capacity (IEC = 92 mEq H+ I g), was used to prepare SPEI membrane obtained by the technique of solvent evaporation, using chloroform. This film was characterized from the following analysis: infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and scanning electron microscopy (SEM) to evaluate the influence of insertion of the sulfonic group in the polymer matrix. The infrared spectrum showed bands of SPEI related to asymmetric vibrations at 1240cm- 1 (S = 0 = 0), in symmetric stretch at 1171 cm-1 (0 = S = 0) and S0 stretch between 1010-1024cm-1. This indicates the presence of sulfonic groups. The DSC analysis was carried out between 150-250C. In this range, there are no significant changes in glass transition temperature of the modified polymer (217C). It is believed that the decomposition of the sulfone group occurs before the temperature reaches the Tg of the polymer. This assumption is confirmed in the TGA analysis. The images of SEM showed that films were obtained free of pores and defects. The membrane SPEI obtained by the technique of solvent evaporation, was used for testing permeation of gases 02, N2 and C02 in order to determine the permeability and selectivity of the membrane. The permeabilities found for oxygen were 0.76 barrer for PEI and 0.46 barrer for SPEI. The selectivity of carbon dioxide relative to oxygen increased from 3.5 to 4.83. Regarding nitrogen, the permeability measurements were 0.064 barrer and 0.043 barrer for the PEI and the SPEI, respectively, while the selectivity relative to C02 increased from 41.1 to 55.5. These results indicate that the predominant effect of sorption due to increased molecular interactions, thus reducing the free volume, made the membrane sulfonated more compact with lower permeability and higher selectivity. These results agree with the premise that the sulfonation is a promising process for the development of more efficient membranes.