Le présent travail a porté sur l'élaboration des électrodes de TiO2 préparées par oxydation anodique du titane avec différentes structures (couche mince et nanotubes) et modifiées avec des espèces de cérium par électrodéposition. L'objectif est d'agir sur les propriétés physiques et électrochimiques de la couche de TiO2 afin d'améliorer les performances photocatalytiques. Pour cet objectif, l'étude a été réalisée en présence et en absence de lumière UV-A et avec des concentrations variables de polluants de type méthanol ainsi qu' un colorant azoïque, l'Amido Black. Les résultats photo-électrochimiques montrent que la photo activité est améliorée suite à la déposition du cérium et qu'il existe une concentration optimale de l'élément dopant. Cet optimum correspond à un pourcentage atomique Ce/Ti de 0.6 at% et il est associé à une meilleure efficacité de séparation des paires é-h+ photo-générés. Les couches nanotubulaires de TiO2 sont obtenues par anodisation du titane à 20 V pendant 45 min dans trois types d'électrolytes : un mélange d'étylene glycol, de fluorure d'ammonium et d'eau (NT1), un mélange de fluorure de tetrabutyl ammonium et de formamide (NT2), et un mélange de sulfate de sodium, de fluorure d'ammonium et d'eau (NT3). L'électrode élaborée dans l'éthylène glycol (NT1) présente le photocourant et l'activité de décoloration du polluant les plus élevées. Ce résultat est attribué à la bonne concordance entre d'une part la surface spécifique et la fraction solide élevées responsables de l'absorption des photons incidents et d'autre part à une faible vitesse de recombinaison des paires électrons trous.

The atomic layer deposition (ALD) growth of titania thin films was studied for the infiltration of silica photonic crystals. Titania thin films were grown in a custom-built ALD reactor by the alternating pulsing and purging of TiCl4 and water vapor. The conformal nature of ALD growth makes it an ideal candidate for the infiltration of the complex opal structure. Titania is a high refractive index material, which makes it a popular material for use in photonic crystal (PC) applications. Photonic crystals are periodic dielectric structures that forbid the propagation of light in a certain wavelength range. This forbidden range is known as the photonic band gap (PBG). A refractive index contrast of at least 2.8 is required for a complete PBG in an inverted opal structure. Therefore, the rutile structure of titania is more desirable for use in PCs due to its higher index of refraction than the anatase or brookite structure. The growth mechanisms and film properties of the TiO2 thin films were studied. Investigation of the growth mechanisms revealed saturated growth rate conditions for multiple temperature regions. Film characterization techniques included XRD, SEM/EDS, XPS, AFM, reflectivity, and index of refraction measurements. Post growth heat treatment was performed to study the conversion from the as-deposited crystal structure to the rutile structure. After optimization of the deposition process, the infiltration of silica opals for PC applications was attempted. The filling fraction was optimized by increasing the pulse and purge lengths at a deposition temperature of 100oC. Although the silica opals were successfully infiltrated using ALD of TiO2, the long range order of the PC was destroyed after the heat treatment step required to achieve the high index rutile structure.

An investigation of surface structures formed on polycrystalline and single crystal TiO2 (titania) samples having under gone various heat treatments in a controlled hydrogen bearing atmosphere was conducted. The study included the recreation and examination of the process discovered by Sehoon Yoo at Ohio State University to form nanofibers on the surface of polycrystalline TiO2 disks. Fibers were formed by heating samples to 700??in a 5%H2 95%N2 gas stream. The nanofibers formed during this processes are approximately 5-20 nanometers in diameter and can be 100??f nanometers long. The fibers do not actually grow on the surface, but are what remain of the surface as the material around them is removed by the gas stream V i.e., nanocarving. The mechanism of fiber formation and the effect of varying experimental parameters remained unknown and were explored within this study. This included changing gas composition, flow rate, and changes in sample preparation. The effect of isovalent doping and impurities within the starting powder were examined. Sintering temperature and time was investigated to determine the effect of grain size and surface morphologies prior to nanocarving. The effect of elevated temperature and 5%H2 95%N gas on the surface of TiO2 single-crystal wafers was also investigated. Test methods include Thermogravimetric Analysis (TGA), Mass Spectrometry (MS), Scanning Electron Microscopy (SEM), and X-ray diffraction (XRD) analysis.

The study combined photoelectrocatalytic technology (PEC) with electrical glassfiber filter (EGF) to decompose volatile organic compounds (VOCs). External electrical voltage was applied to retard the recombination of electron-electron hole pairs and increase the surface temperature of the photocatalysts coated on the electrical glassfiber filter, which could further decompose VOCs more effectively via photoelectrocatalytic technology. Acetone was selected as the gasous pollutant for this particular study. A commercial TiO2 photocatalyst (AG-160) was coated on GFF via impregnation to decompose acetone in a batch PEC reactor. Operation parameters investigated in this study included acetone concentration (50~400 ppm), electrical voltage (0~6,500V), water content (0~20,000 ppm), reaction temperature (40¢J~80¢J).The incident UV light of 365 nm wavelength was irradiated by three 15-wat low pressure mercury lamps (£f=365 nm) placing above the batch PEC reactor. The TiO2-coated EGF was placed at the center of the batch PEC reactor. Acetone was injected into the reactor by a gasket syringe to conduct the PEC decomposition test. Acetone was analyzed quantitatively by a gas chromatography with a flame ionization detector (GC/FID). Finally, a Langmuir-Hinshelwood kinetic (L-H) model was proposed to simulate the PEC reaction rate of acetone. Experimental results showed that the size range of the self-produced nano-sized photocatalyst prepared by sol-gel was 35~50 nm. Three duplicate tests of PC and PEC degradation of acetone indicated that TiO2 was not deactivated during the PC and PCE reactions, hence TiO2 can be reused in the experiments. Results obtained from the PC and PEC degradation experiments indicated that the PEC reaction rate was higher than the PC reaction rate.The PEC reaction rate increased with applied electrical voltage, and the highest decomposition efficiency occurred at 6,500 V. Electrical field generated by the differences of electrical voltage can effectively enhance the oxidation capability of TiO2 since electron (e-) can be conducted to retard the recombination of electron and electron hole pairs. Both PC and PEC technologies could be used to decompose acetone. Among them, PEC had highter decomposition efficiency of acetone than PC up to 34%. Rsults obtained from the operation parameter tests reaveled that raising electrical voltage could enhance the decomposition efficiency of acetone only for electrical voltages above 2,000 V. However, the decomposition efficiency of acetone tended to level off as electrical voltage became higher. Zero-order reaction rate of the PEC reaction was observed for initial acetone concentration of 100~400 ppm, while the PEC reaction decreased gradually for initial acetone concentration reaction below 100 ppm. It revealed that the PEC reaction was pseudo ozero-order for initial acetone concentration of 100~400 ppm, and pseudo first-order reaction for acetone concentration below 100 ppm. Additionally, the PC reaction rate increased with temperature at 45-80¢J. However the PEC reaction rate increased with temperature at 45-60¢J, and decreased with temperature at 60-80¢J. An adsorptive competition between acetone and water molecules at the active sites over TiO2 surface caused either promotion or inhibition of TiO2 decomposition depending on moisture content . For the PC and PEC reactions, the optimum operating condition of water vapor concentration was 10,000 ppm, but inhibition occurred when the water vapor concentration increased up to 20,000 ppm. Finally, the Langmuir-Hinshelwood kinetic model was applied to investiage the influences of reaction temperature, initial concentration of acetone, and water content on the photoelectrocatalytic reaction rate of acetone. Model simulation results showed that photoelectrocatalytic reaction rate constant of acetone(kLH) and adsorptive equilibrium constant(KA) increased with electrical voltage and acetone initial concentration. This study sevealed that experimental and simulated results were in good agreement. Thus, PEC reaction rate of acetone on the surface of TiO2 can be also succesfully simulated by the L-H kinetic model.

Alternative energy sources such as solar energy have attracted an extensive interest in the petroleum shortage era. Among solar cells, dye-sensitized solar cell (DSSC) attracts the attention of widespread research teams because of the easy-production process, low cost, and good photon-to-electron conversion efficiency. In this study, both UV and acid solution such as HCl are used to improve the efficiency of DSSC. The UV illumination can eliminate organic contaminates on TiO2 by photocatalysis and enhance the adsorption of dye molecules. Meanwhile, the coordination mode between TiO2 and dye could be changed and lower the electron transportation. If the HCl solution is used after UV illumination, the coordination mode can be preserved. Moreover, H+ from HCl can attract the COO¡Ð anchoring group of dye by electrostatic force. It further increases the adsorption of dye and improves the DSSC efficiency. The coordination mode was measured by Fourier-transform infrared spectrometer (FTIR). The internal resistance was measured by electrical impedance spectroscopy (EIS). The chemical properties were characterized by X-ray photoelectron spectroscopy (XPS). The light absorbance was measured by ultraviolet-visible spectroscopy (UV-Vis). The morphology was observed by field emission scanning electron microscope (FE-SEM). The performance of the cells was measured by a semiconductor device analyzer. In our results, the conversion efficiency was improved from 6.29% of untreated one to 6.71 and 7.39% for UV and UV + HCl treated ones.

An atomic level understanding of the structure and stability of model catalysts is essential for surface science studies in heterogeneous catalysis. Scanning tunneling microscopy (STM) can operate both in UHV and under realistic pressure conditions with a wide temperature span while providing atomic resolution images. Taking advantage of the ability of STM, our research focuses on 1) investigating the structure and stability of supported Au catalysts, especially under CO oxidation conditions, and 2) synthesizing and characterizing a series of alloy model catalysts for future model catalytic studies. In our study, Au clusters supported on TiO2(110) have been used to model supported Au catalysts. Our STM studies in UHV reveal surface structures of TiO2(110) and show undercoordinated Ti cations play a critical role in the nucleation and stabilization of Au clusters on TiO2(110). Exposing the TiO2(110) surface to water vapor causes the formation of surface hydroxyl groups and subsequently alters the growth kinetics of Au clusters on TiO2(110). STM studies on Au/TiO2(110) during CO oxidation demonstrate the real surface of a working catalyst. Au clusters supported on TiO2(110) sinter rapidly during CO oxidation, but are mostly stable in the single component reactant gas, either CO or O2. The sintering kinetics of supported Au clusters has been measured during CO oxidation and gives an activation energy, which supports the mechanism of CO oxidation induced sintering. CO oxidation was also found to accelerate the surface diffusion of Rh(110). Our results show a direct correlation between the reaction rate of CO oxidation and the diffusion rate of surface metal atoms. Synthesis of alloy model catalysts have also been attempted in our study with their structures successfully characterized. Planar Au-Pd alloy films has been prepared on a Rh(100) surface with surface Au and Pd atoms distinguished by STM. The growth of Au-Ag alloy clusters have been studied by in-situ STM on a cluster-to-cluster basis. Moreover, the atomic structure of a solution-prepared Ru3Sn3 cluster has been resolved on an ultra-thin silica film surface. The atomic structure and adsorption sites of the ultrathin silica film have also been well characterized in our study.

Abstract Recently, titanium dioxide¡]TiO2¡^ is one of the most extensively studied transition-metal oxides because of its remarkable photocatalyst efficiency and electronic properties. In this paper, thin films ware obtained by dual ion beam sputtering. By different processes, these samples can be classified into three categories. Firstly, thin films, deposited on 200 mash copper grids for 15 minutes, were investigated that many TiO grains is about 5 nm in size by transmission electron microscopy¡]TEM¡^. Next, TiO2 thin films, sputtered on si wafers and glass for 180 minutes in an O2 environment by using titanium target, were initially identified by X ray diffraction instrument¡]XRD¡^. The result shows that some thin films have good orientations. By TEM, TiO2 grains on bottom of films are about 20 nm. By scanning electron microscopy¡]SEM¡^, TiO2 grains on the surface are about 1~2 £gm in size and are oblong in shape. The last, TiO thin films were directly deposited on si wafer for 180 minutes in no O2 environment by using titanium target and then annealed to transform from TiO to TiO2. By XRD, the thin film, annealed at 600¢J for 1hr, has good orientation. By TEM, TiO2 grains, annealed at 1000¢J for 24hr, grow up to 1-2 £gm in size and are oblong in shap.

In the work, photocatalytical treatment of acetic acid wastewater by nanostructured film of TiO2 under ultra-violet ¡]UV¡^ light illumination was studied. Nanosized TiO2 suspension was prepared by the sol-gel process. Then it was dip-coated on indium tin-oxide¡]ITO¡^glass, which could be used as the anode if applicable. Effects the UV light intensity, UV light wavelength, reactive area of TiO2 film, solution pH, and applied bias voltage on photocatalysis efficiency of acetic acid in term of COD removal were studied in this work. Experimental results have shown that a pseudo first-order kinetics was obeyed in all tests. In this study UV light of 312nm outperformed that of 365nm ¡]15.3¢H vs. 11.0¢H¡^. UV light intensity of 20W was also found to be superior to 10W with COD removal of 11.0¢H against 6.7¢H. COD removal at pH¡×3.18 was about 3.6 times greater as compared with that of at pH=9.98. When the reactive area of TiO2 film was increased to three times, the COD removal was almost doubled. An applied external voltage was found to enhance the removal of COD. When an external voltage of 15V was applied, the COD removal was increased to 84.6¢H. It is ascribed to an external voltage would prevent or lower the extent of electron-hole recombination. In this work, the pseudo first-order reaction rate equation K¡¬=1.7679(COD)-0.7547 was obtained for various concentrations of acetic acid tested.

In part I, MgO and Co1-xO powders in 9:1 and 1:9 molar ratio (denoted as M9C1 and M1C9 respectively) were sintered and homogenized at 1600oC followed by annealing at 850 and 800oC, respectively to form defect clusters and precipitates. Analytical electron microscopic (AEM) observations indicated the protoxide remained as rock salt structure with complicated planar diffraction contrast for M9C1 sample, however with spinel paracrystal precipitated from the M1C9 sample due to the assembly of charge- and volume-compensating defects of the 4:1 type, i.e. four octahedral vacant sites surrounding one Co3+-filled tetrahedral interstitial site. The spacing of such defect clusters is 4.5 times the lattice spacing of the average spinel structure of Mg-doped Co3-dO4, indicating a higher defect cluster concentration than undoped Co3-dO4. The {111} faulting of Mg-doped Co3-dO4/Co1-xO in the annealed M1C9 sample implies the possible presence of zinc blend-type defect clusters with cation vacancies assembled along oxygen close packed (111) plane. In part II, the Mg2TiO4/MgO composites prepared by reactive sintering MgO and TiO2 powders (9:1 molar ratio) at 1600oC and then air-cooled or further aged at 900oC were studied by X-ray diffraction and (AEM) in order to characterize the microstructures and formation mechanism of nanosized Mg2TiO4 spinel precipitated from Ti-doped MgO. Expulsion of Ti4+ during cooling caused the formation of (001)-specific G.P. zone under the influence of thermal/sintering stress and then the spinel precipitates, which were about 30 nm in size and nearly spherical with {111} and {100} facets to minimize coherency strain energy and surface energy. Secondary nano-size spinel was precipitated and became site saturated during aging at 900oC, leaving a precipitate free zone at the grain boundaries of Ti-doped MgO. The intergranular spinel became progressively Ti-richer upon aging 900oC and showed <110>-specific diffuse scatter intensity likely due to short range ordering and/or onset decomposition. In part III, the Co1-xO/Co2TiO4 composite prepared by reactive sintering CoO and TiO2 powders (9:1 molar ratio) at 1450oC and then air-cooled were studied by X-ray diffraction and AEM in order to characterize the microstructures and formation mechanism of nanosized Co2TiO4 spinel precipitated from Ti-doped Co1-xO. Slight expulsion of Ti4+ during cooling caused the precipitation of nanosize Co2TiO4 spinel. Bulk site saturation also caused impingement of the Co2TiO4 precipitates upon growth. The Co3-dO4 spinel, as an oxidatin product of Co1-xO, was found to form at free surface and the Co1-xO/Co2TiO4 interface. The Co2TiO4 spinel particles formed by reactive sintering rather than precipitation were able to detach from the Co1-xO grain boundaries to reach parallel epitaxial orientation with respect to the host Co1-xO grains via Brownian-type rotation of the embedded particles. In part IV, AEM was used to study the defect microstructures of Zr-dissolved TiO2 prepared via reactive sintering the ZrO2 and TiO2 powders (8:92 in molar ratio, designated as Z8T92) at 1600oC for 24 h and then aged at 900oC for 2-200 h in air. The Zr-dissolved TiO2 with rutile structure showed dislocation arrays, defect clusters, G.P. zone, superlattice, nanometer-size domains incommensurate and commensurate superstructure, may be the precursor of ZrTi2O6 precipitates at 900oC. The rutile showed diffuse diffractions along [001] direction as a result of Zr4+ substitution for Ti4+ with volume compensating defect clusters. Incommensurate and commensurate structures, as indicated by diffraction splitting and extra diffraction along <100> and <010> directions may be attributed to the ordering and clustering process of Zr and Ti atoms in these directions. Part V, deals with the reactive sintering of ZrO2 and TiO2 powders (1:4 molar ratio) at 1400 to 1600oC in air to form orthorhombic ZrTiO4 (a-PbO2-type structure, denoted as a) and to study its epitaxial reorientation in the matrix of tetragonal TiO2 (rutile) grains with Zr4+ (15 mol %) dissolution. The epitaxial relationship of intragranular ZrTiO4 and Zr-dissolved rutile (denoted as r) was determined by electron diffraction as [010]a//[011]r; (001)a // (011)r (i.e. [100]a // [100]r; (001)a // (011)r). The reorientation of the intragranular particles in the composites can be reasonably explained by rotation of the nonepitaxial particles above a critical temperature (T/Tm > 0.8) and below a critical particle size for anchorage release at interface with respect to the host grain. Reactive sintering facilitated the reoreientation process for the particles about to detach from the grain boundaries. The Brownian rotation of the confined ZrTiO4 particles in rutile grains was activated by a beneficial lower interfacial energy for the epitaxial relationship, typically forming lath-like ZrTiO4 with (101)a/(211)r habit plane having fair match of oxygen atoms at the interface. Further aging at 900oC for 50 h in air caused modulated and periodic antiphase domains in ZrTiO4 matrix, as likely precursor of equilibrium ZrTi2O6.

The aim of this study was to investigate the viability of patterning by immobilization, photocatalytic removal, and re-immobilization steps of the enzyme on photocatalytically active thin films for biosensor fabrication purposes. For this aim, TiO2-SiO2-Au sol-gel colloids were synthesized and deposited on glass substrates as thin films by dip coating. Cysteamine linker was assembled on gold nanoparticles to functionalize thin films with amine groups for immobilization of model enzyme invertase. Effect of immobilization temperature, enzyme concentration of the immobilization solution and immobilization period on invertase immobilization were investigated. The immobilized invertase activity was found independent from the immobilization temperature in the range tested (4oC-room temperature). The optimum enzyme concentration and period for immobilization was determined as 10&micro / g/ml and 12 hours respectively. The resulting invertase immobilized thin films showed high storage stability retaining more that 50% of their initial activity after 9 weeks of storage. Photocatalytic enzyme removal and re-immobilization studies were carried out by irradiating the invertase immobilized thin films with blacklight. Upon 30 minutes of irradiation, immobilized invertase was completely and irreversibly inactivated. Initial immobilized invertase activity (before the irradiation) was attained when invertase was re-immobilized on thin films that were irradiated for 5 hours. Thus it was inferred that with sufficient exposure, enzymes can be completely removed from the surfaces which makes the re-immobilization possible. The possibility of enzyme removal with photocatalytic activity and re-immobilization can pave the way to new patterning techniques to produce multi-enzyme electrode arrays.