Combined Cycle Power Plant (CCPP)s play a key role in modern powersystem due to their lesser investment cost, lower project executiontime, and higher operational flexibility compared to other conventionalgenerating assets. The nature of generation system is changing withever increasing penetration of the renewable energy resources. Whatwas once a clearly defined generation, transmission, and distributionflow is shifting towards fluctuating distribution generation. Because ofvariation in energy production from the renewable energy resources,CCPP are increasingly required to vary their load levels to keep balancebetween supply and demand within the system. CCPP are facingmore number of start cycles. This induces more stress on the gas turbineand as a result, maintenance intervals are affected.The aim of this master thesis project is to develop a dispatch algorithmfor the short-term operation planning for a combined cyclepower plant which also includes the long-term constraints. The longtermconstraints govern the maintenance interval of the gas turbines.These long-term constraints are defined over number of EquivalentOperating Hours (EOH) and Equivalent Operating Cycles (EOC) forthe Gas Turbine (GT) under consideration. CCPP is operating in theopen electricity market. It consists of two SGT-800 GT and one SST-600 Steam Turbine (ST). The primary goal of this thesis is to maximizethe overall profit of CCPP under consideration. The secondary goal ofthis thesis it to develop the meta models to estimate consumed EOHand EOC during the planning period.Siemens Industrial Turbo-machinery AB (SIT AB) has installed sensorsthat collects the data from the GT. Machine learning techniqueshave been applied to sensor data from the plant to construct Input-Output (I/O) curves to estimate heat input and exhaust heat. Resultsshow potential saving in the fuel consumption for the limit on CumulativeEquivalent Operating Hours (CEOH) and Cumulative EquivalentOperating Cycles (CEOC) for the planning period. However, italso highlighted some crucial areas of improvement before this economicdispatch algorithm can be commercialized. / Kombicykelkraftverk spelar en nyckelroll i det moderna elsystemet pågrund av den låga investeringskostnaden, den korta tiden för att byggaett nytta kraftverk och hög flexibilitet jämfört med andra kraftverk.Elproduktionssystemen förändras i takt med en allt större andel förnybarelproduktion. Det som en gång var ett tydligt definierat flödefrån produktion via transmission till distribution ändrar nu karaktärtill fluktuerande, distribuerad generering. På grund av variationernai elproduktion från förnybara energikällor finns ett ökat behov avatt kombicykelkraftverk varierar sin elproduktion för att upprätthållabalansen mellan produktion och konsumtion i systemet. Kombicykelkraftverkbehöver startas och stoppas oftare. Detta medför mer stresspå gasturbinen och som ett resultat påverkas underhållsintervallerna.Syftet med detta examensarbete är att utveckla en algoritm för korttidsplaneringav ett kombicykelkraftverk där även driften på lång siktbeaktas. Begränsningarna på lång sikt utgår från underhållsintervallenför gasturbinerna. Dessa långsiktiga begränsningar definieras som antaletekvivalenta drifttimmar och ekvivalenta driftcykler för det aktuellakraftverket. Kombikraftverket drivs på den öppna elmarknaden.Det består av två SGT-800 GT och en SST-600 ångturbin. Det främstamålet med examensarbetet är att maximera den totala vinsten förkraftverket. Ett sekundärt mål är att utveckla metamodeller för attskatta använda ekvivalenta drifttimmar och ekvivalenta driftcyklerunder planeringsperioden.Siemens Industrial Turbo-machinery AB (SIT AB) har installeratsensorer som samlar in data från gasturbinerna. Maskininlärningsteknikerhar tillämpats på sensordata för att konstruera kurvor för attuppskatta värmetillförseln och avgasvärme. Resultaten visar en potentiellbesparing i bränsleförbrukningen om de sammanlagda ekvivalentadrifttimmarna och de sammanlagda ekvivalenta driftcyklernabegränsas under planeringsperioden. Det framhålls dock också att detfinns viktiga förbättringar som behövs innan korttidsplaneringsalgoritmenkan kommersialiseras.

To push the thermal efficiency of turbomachinery, the turbine inlet temperature must be raised, eventually reaching and surpassing the blade material thermal limits. Internal geometry, such as pin fin arrays, has been the go-to solution for higher thermal environments to remove heat from blades and vanes to prevent material failure. The industry standard for turbomachinery in energy generation uses the steam Rankine or the Brayton cycle. Classically, these cycles have used air as the operating fluid environment. Over the past decade, novel solutions have begun changing how we design cycles, with one promising solution emerging: the supercritical carbon dioxide (sCO2) power cycle. Promising higher cycle efficiency with a smaller footprint has quickly become an attractive alternative for power generation. Although thorough research of pin fin arrays as turbulators in the trailing edge of turbine blade internal design has been a focus of research for the past several decades, in the sCO2 novel working environment, the need to re-visit the heat transfer characterization of internal cooling is necessary. This study was executed two-fold, first numerically and then experimentally. The first objective of this paper is to explore the heat transfer characteristics of sCO2 as the cooling environment in a staggered pin fin array, defined within the supercritical phase, using steady RANS conjugate heat transfer. An adapted correlation for the Nusselt number was derived, dependent on the Reynolds number, to provide a stronger correlation than existing air data-derived correlations in the literature. Taking this numerically derived correlation, the second objective of this paper is to design and run a matching experimental geometry fabricated for testing at target operating conditions of 400 Celsius and 200 bar. This data was then processed in tandem with the numerical and available derived data in the literature for direct comparison.

Combined cycle power plants haven becoming one of the mainstream power plants in the twenty-one century. The emergence of high 600¢J exhaust temperature of the gas turbine, due to the recent rapid enhancement of aerospace material and blade cooling methods, upgrades the gas turbine from low efficiency dual pressure non-reheat unit to high efficiency triple pressure reheat combined cycle power plants. In addition, the increase of turbine inlet temperature by 10~15¢J every year leads to the renewal of the advanced models gas turbine less than ten years. There are three-turbine inlet temperature (TIT) definitions in the gas turbine: (1) TA defines firing temperature as the mass flow mean total temperature before the first-stage stationary diagram edge plane.( Westinghouse or MHI product) (2) TB defines fire temperature as the mass flow mean total temperature at the first-stage nozzle trailing edge plane, ( GE product). (3) TC defines ISO firing temperature; it is a stoichiometric combustion temperature. It is not a physical temperature. ( Siemens ¡® Alstom ABB product). This study shows how to calculate compressor inlet mass flow balance, turbine power balance and heat balance on the combustion chamber system. In order to prove correctness of the balance equation, the data are taken from the heat balance diagram and acceptance test of Nan-pu power station combined cycle. The result shows that the study is sultable for application of the optimum analysis for CCPP operation performance. This type of combined cycle power plant suits not only for the base-load but also for the cycling-load operation.

An investigation into the performance of several combined gas-steam power generating plants’ cycles was undertaken at the School of Engineering and Technology at the University of Hertfordshire and it is predominantly analytical in nature. The investigation covered in principle the aspect of the fundamentals and the performance parameters of the following cycles: gas turbine, steam turbine, ammonia-water, partial oxidation and the absorption chiller. Complete thermal analysis of the individual cycles was undertaken initially. Subsequently, these were linked to generate a comprehensive computer model which was employed to predict the performance and characteristics of the optimized combination. The developed model was run using various input parameters to test the performance of the cycle’s combination with respect to the combined cycle’s efficiency, power output, specific fuel consumption and the temperature of the stack gases. In addition, the impact of the optimized cycles on the generation of CO2 and NOX was also investigated. This research goes over the thermal power stations of which most of the world electrical energy is currently generated by. Through which, to meet the increase in the electricity consumption and the environmental pollution associated with its production as well as the limitation of the natural hydrocarbon resources necessitated. By making use of the progressive increase of high temperature gases in recent decades, the advent of high temperature material and the use of large compression ratios and generating electricity from high temperature of gas turbine discharge, which is otherwise lost to the environment, a better electrical power is generated by such plant, which depends on a variety of influencing factors. This thesis deals with an investigation undertaken to optimize the performance of the combined Brayton-Rankine power cycles' performance. This work includes a comprehensive review of the previous work reported in the literature on the combined cycles is presented. An evaluation of the performance of combined cycle power plant and its enhancements is detailed to provide: A full understanding of the operational behaviour of the combined power plants, and demonstration of the relevance between power generations and environmental impact. A basic analytical model was constructed for the combined gas (Brayton) and the steam (Rankine) and used in a parametric study to reveal the optimization parameters, and its results were discussed. The role of the parameters of each cycle on the overall performance of the combined power cycle is revealed by assessing the effect of the operating parameters in each individual cycle on the performance of the CCPP. P impacts on the environment were assessed through changes in the fuel consumption and the temperature of stack gases. A comprehensive and detailed analytical model was created for the operation of hypothetical combined cycle power and power plant. Details of the operation of each component in the cycle was modelled and integrated in the overall all combined cycle/plant operation. The cycle/plant simulation and matching as well as the modelling results and their analysis were presented. Two advanced configurations of gas turbine cycle for the combined cycle power plants are selected, investigated, modelled and optimized as a part of combined cycle power plant. Both configurations work on fuel rich combustion, therefore, the combustor model for rich fuel atmosphere was established. Additionally, models were created for the other components of the turbine which work on the same gases. Another model was created for the components of two configurations of ammonia water mixture (kalina) cycle. As integrated to the combined cycle power plant, the optimization strategy considered for these configurations is for them to be powered by the exhaust gases from either the gas turbine or the gases leaving the Rankine boiler (HRSG). This included ChGT regarding its performance and its environmental characteristics. The previously considered combined configuration is integrated by as single and double effect configurations of an ammonia water absorption cooling system (AWACS) for compressor inlet air cooling. Both were investigated and designed for optimizing the triple combination power cycle described above. During this research, tens of functions were constructed using VBA to look up tables linked to either estimating fluids' thermodynamic properties, or to determine a number of parameters regarding the performance of several components. New and very interesting results were obtained, which show the impact of the input parameters of the individual cycles on the performance parameters of a certain combined plant’s cycle. The optimized parameters are of a great practical influence on the application and running condition of the real combined plants. Such influence manifested itself in higher rate of heat recovery, higher combined plant thermal efficiency from those of the individual plants, less harmful emission, better fuel economy and higher power output. Lastly, it could be claimed that various concluding remarks drawn from the current study could help to improve the understanding of the behaviour of the combined cycle and help power plant designers to reduce the time, effort and cost of prototyping.