In this thesis, the structural design, structural analysis and producibility analysis of an unmanned aerial vehicle wing were performed. Three different wing models, made of different materials, were designed. The wings were aluminum wing model and composite wing models / made of prepreg and wet lay-up. All wings have the same aerodynamic geometry and structural configuration under the same flight conditions. The structural designs of three wings were done by using Unigraphics NX. The finite element modeling of the wings were built by using MSC Patran package program. After the application of the loads on models, structural analyses were performed by MSC Nastran. Finally, the producibility analysis of prepreg wing model was conducted by using FiberSIM package program. The prepreg wing model was selected as optimum design with studies conducted in the study considering weight, producibility, cruise and gust stress and displacement conditions.

In this thesis, computational aerodynamics, structural and aeroelastic analyses of the composite tactical unmanned air vehicle which is designed and manufactured in the Department of Aerospace Engineering are performed. Verification of the structural integrity of the air vehicle is shown at the minimum maneuvering and the dive speeds at the static limit loads which are calculated by the computational aerodynamics analysis of the full aircraft model. In the current work, aerodynamic loads are re-calculated for more accurately determined dive speed angle of attack in an effort to match the overall vertical pressure load more closely to the half of the aircraft weight at the positive load factor. Finite element models of the fuselage, wing and the vertical-horizontal tail plane are prepared including the filament wound boom connecting the wing and the tail plane. Structural analyses of the composite wing, vertical and horizontal tail plane are performed under the limit aerodynamic loads calculated at the corner points of the V-N diagram using the structural finite element model of the wing-tail plane combination only. Global finite element analysis of the wing-tail plane combination showed that composite and isotropic materials of the wing-tail plane combination have positive margins of safety. Woven carbon and E-glass fabric that was procured to be used for the serial production version of the airplane are characterized for the tensile properties by the tests. Comprehensive aeroelastic stability analyses of the airplane are conducted by adding one sub-structure at a time to the aeroelastic model. Specifically, aeroelastic models which are used are the wing only, wing-tail plane combination, complete air vehicle with and without wing control surfaces. With such a study it is intended to address the effect each sub-structure adds to the aeroelastic model on the critical aeroelastic stability modes and speeds, and to see how sensitive the aeroelastic stability modes and speeds are to model fidelity. Detailed structural and aeroelastic analyses showed that the airplane has sufficient structural integrity under the action of static limit loads, and no aeroelastic instability is expected to occur within the flight envelope of the airplane.

This thesis presents an integrated framework for online obstacle avoidance of rotary-wing unmanned aerial vehicles (UAVs), which can provide UAVs an obstacle field navigation capability in a partially or completely unknown obstacle-rich environment. The framework is composed of a LIDAR interface, a local obstacle grid generation, a receding horizon (RH) trajectory optimizer, a global shortest path search algorithm, and a climb rate limit detection logic. The key feature of the framework is the use of an optimization-based trajectory generation in which the obstacle avoidance problem is formulated as a nonlinear trajectory optimization problem with state and input constraints over the finite range of the sensor. This local trajectory optimization is combined with a global path search algorithm which provides a useful initial guess to the nonlinear optimization solver. Optimization is the natural process of finding the best trajectory that is dynamically feasible, safe within the vehicle's flight envelope, and collision-free at the same time. The optimal trajectory is continuously updated in real time by the numerical optimization solver, Nonlinear Trajectory Generation (NTG), which is a direct solver based on the spline approximation of trajectory for dynamically flat systems. In fact, the overall approach of this thesis to finding the optimal trajectory is similar to the model predictive control (MPC) or the receding horizon control (RHC), except that this thesis followed a two-layer design; thus, the optimal solution works as a guidance command to be followed by the controller of the vehicle. The framework is implemented in a real-time simulation environment, the Georgia Tech UAV Simulation Tool (GUST), and integrated in the onboard software of the rotary-wing UAV test-bed at Georgia Tech. Initially, the 2D vertical avoidance capability of real obstacles was tested in flight. Then the flight test evaluations were extended to the benchmark tests for 3D avoidance capability over the virtual obstacles, and finally it was demonstrated on real obstacles located at the McKenna MOUT site in Fort Benning, Georgia. Simulations and flight test evaluations demonstrate the feasibility of the developed framework for UAV applications involving low-altitude flight in an urban area.

Η παρούσα διπλωματική έχει ως αντικείμενο την μελέτη των συστημάτων προώθησης και την εξέταση των δυνατοτήτων χρησιμοποίησης νέων μορφών προωθητηρίων. Συγκεκριμένα θεωρώντας ότι μέχρι σήμερα το κύριο σύστημα προώθησης UAV είναι οι DC κινητήρες σε συνδυασμό με έλικες μελετάται η δυνατότητα χρήσης Jet κινητήρων για την παραγωγή της απαιτούμενης ώσης που χρειάζεται ένα UAV κατά την αιώρηση. Οι στροβιλοκινητήρες έχουν την δυνατότητα παραγωγής σταθερής ώσης και χρησιμοποιούνται σχεδόν αποκλειστικά στα μεγάλης κλίμακας ιπτάμενα οχήματα. Υπάρχουν διάφοροι τύποι στροβιλοκινητήρων στην αγορά, οι οποίοι όμως βασίζονται στις ίδιες αρχές λειτουργίας. Κατά την εργασία μελετήθηκε ο μοντελιστικός Jet κινητήρας JetCat P20. Έγινε προσπάθεια μοντελοποίησης του εν λόγω κινητήρα λαμβάνοντας υπόψη όλα τα χαρακτηριστικά του. Το άγνωστο έως τώρα σύστημα μοντελοποιήθηκε και έγινε μελέτη της δυναμικής του. Οι Jet κινητήρες λόγω της φυσικών νόμων που τους διέπουν παρουσιάζουν σχετικά αργές αποκρίσεις. Οι σταθερές χρόνου αυτών των κινητήρων καθιστούν την δυνατότητα χρήσης τους σε UAV εφαρμογές αρκετά δύσκολη. Με την χρήση του JetCat P20 σε μια πραγματική εφαρμογή ελέγχου της γωνιάς ενός οδηγούμενου εκκρεμούς αναζητήθηκαν τα όρια και οι δυνατότητες ελέγχου αυτού του προωθητικού συστήματος. Οι Jet κινητήρες τελικά, όπως ο JetCat P20 έχουν αρκετά καλές δυνατότητες παραγωγής συγκεκριμένου επιπέδου ώσης, επομένως και ρύθμισης της γωνίας του εκκρεμούς, ωστόσο οι χρόνοι απόκρισής του είναι αρκετά μεγάλοι για τα δεδομένα UAV εφαρμογών, χωρίς να υπάρχουν πολλά περιθώρια βελτίωσης μέσω κλασσικού έλεγχου. / This thesis object is the study of propulsion systems and the examination of using new systems for propulsion. Especially, considering that until now the main propulsion system for UAV's are DC motors in combination with propellers we are examining the possibility of using Jet engine to generate the required thrust needed a UAV in hover. The turbines have the ability to produce constant thrust and are used almost exclusively in large-scale flight vehicles. There are different types of turbines on the market, but they are based on the same principles of operation. During this thesis, we are experimenting with the Jet engine JetCat P20. The Jet Engine system was modeled and we examined its dynamic.The Jet engines ,because of the physical laws governing them, have relatively slow time responses. The time constants of these motors makes it difficult to use in UAV applications. We have used the JetCat P20 in a real application ,where we tried to control the angle of a driven pendulum.The Jet engines finally, like JetCat P20 have pretty good production capabilities thrust level, and thus adjusting the angle of the pendulum, but their response time is large enough for the UAV applications, without much scope for improvement through classical control.

Inflatable-wing Unmanned Aerial Vehicles (UAVs) have the ability to be packed in a fraction of their deployed volume. This makes them ideal for many deployable UAV designs, but inflatable wings can be flexible and don’t have conventional control surfaces. This thesis will investigate the use of wing warping as a means of autonomous control for inflatable wings. Due to complexities associated with manufacturing inflatable structures a new method of rapid prototyping deformable wings is used in place of inflatables to decrease cost and design-cycle time. A UAV testbed was developed and integrated with the warping wings and flown in a series of flight tests. The warping wing flew both under manual control and autopilot stabilization.

L'objet de cette thèse est de démonter la faisabilité de conception d'un mini-drone longue endurance sans recourir à des véhicules de grande envergure qui nécessite des infrastructures supplémentaires, des systèmes de lancement complexes et un personnel d'exploitation important. Pour ce faire, une approche d'optimisation globale du problème a été utilisée, en s'appuyant sur les spécificités de chacun des aspects de la conception de mini-drones. Ce concept de mini-drone longue endurance doit repousser les limites dans plusieurs disciplines telles que l'aérodynamique, la propulsion, les structures, les sources d'énergies et le stockage, le contrôle et la navigation, ainsi que la miniaturisation de l'électronique embarquée. Un programme de conception baptisé Cdsgn a été développé et prend en compte les problèmes spécifiques de chaque discipline consacrées aux mini-drones. Il permet de voir l'influence de chaque paramètre de conception sur la performance finale de la conception, menant à la sélection optimale des paramètres. Cdsgn génère et analyse rapidement de nombreuses configurations de l'avion tout en simulant la performance de chaque configuration pour un pro fil de mission donnée. Un outil de post-traitement a également été développé afin de filtrer et sélectionner de manière interactive les paramètres de conception parmi les nombreuses configurations pour répondre à des applications pratiques. Le programme proposé a été utilisé dans le développement et la conception de plusieurs projets, tels que Solar Storm, premier mini-drone hybride au monde à énergie solaire d'une envergure de cinquante centimètre, SPOC, un mini-drone longue distance conçu pour voler au-dessus de la mer Méditerranée de Nice jusqu'en Corse (Calvii) et enfin Eternity, mini-drone de longue endurance d'une envergure d'un mètre, avec une configuration classique. Capable d'une autonomie de quatre heures avec les batteries embarquées, son temps de vol peut être amélioré jusqu'à huit heures avec l'utilisation de l'énergie solaire. En utilisant les évaluations de chaque projet, Cdsgn a été amélioré à la fois pour l'exactitude des calculs et pour la performance opérationnelle afin de développer le plus petit véhicule aérien pour une mission d'endurance donnée.

Multiple Cooling Multi Objective Simulated Annealing algorithm has been combined with a conceptual design code written by the author to carry out a multi objective design optimization of an Agricultural Aerial Robot. Both the single and the multi objective optimization problems are solved. The performance figures of merits for different aircraft configurations are compared. In this thesis the potential of optimization as a powerful design tool to the aerospace problems is demonstrated.

Thesis (MScEng)-- Stellenbosch University, 2012. / ENGLISH ABSTRACT: This thesis presents the analysis, design, simulation and practical implementation of a control system to achieve an accurate autonomous landing of a fixed-wing unmanned aerial vehicle in the presence of wind gust atmospheric disturbances. Controllers which incorporate the concept of direct-lift control were designed based on a study of the longitudinal dynamics of the UAV constructed as a testbed. Direct-lift control offers the prospect of an improvement in the precision with which aircraft height and vertical velocity can be controlled by utilising actuators which generate lift directly, instead of the conventional method whereby the moment produced by an actuator results in lift being indirectly generated. Two normal specific acceleration controllers were designed. The first being a conventional moment-based controller, and the second a direct-lift-augmented controller. The moment-based controller makes use of the aircraft’s elevator while the direct-lift augmented controller in addition makes use of the flaps of the aircraft which serve as the direct-lift actuator. Controllers were also designed to regulate the airspeed, altitude, climb rate, and roll angle of the aircraft as well as damp the Dutch roll mode. A guidance controller was implemented to allow for the following of waypoints. A landing procedure and methodology was developed which includes the circuit and landing approach paths and the concept of a glide path offset to calibrate the touchdown point of a landing. All controllers and the landing procedure were tested in a hardware-in-the-loop simulation environment as well as practically in a series of flight tests. Five fully autonomous landings were performed, three of these using the conventional NSA controller, and the final two the direct-lift-augmented NSA controller. The results obtained during the landing flight tests show that the project goal of a landing within five meters along the runway and three meters across the runway was achieved in both normal wind conditions as well as in conditions where wind gusts prevailed. The flight tests also showed that the direct-lift-augmented NSA controller appears to achieve a more accurate landing than the conventional NSA controller, especially in the presence of greater wind disturbances. The direct-lift augmented NSA controller also exhibited less pitch angle rotation during landing. / AFRIKAANSE OPSOMMING: Hierdie tesis verteenwoordig die analise, ontwerp, simulasie en praktiese implementering van ’n beheerstelsel wat ten doel het om ’n akkurate en outonome landing van ’n onbemande vastevlerk vliegtuig in rukwind atmosferiese toestande te bewerkstellig. Gegrond op ’n studie van die longitudinale dinamika van die vliegtuig wat as proeftuig gebruik is, is beheerders ontwerp wat die beginsel van direkte-lig insluit. Direkte-lig beheer hou die potensiaal in om die vliegtuig se hoogte en vertikale snelheid akkuraat te beheer deur gebruik te maak van aktueerders wat lig direk genereer in teenstelling met die konvensionele metode waar die moment van die aktueerder indirek lig genereer. Twee normaal-versnellings beheerders is ontwerp. Die eerste is ’n konvensionele moment-gebaseerde beheerder wat gebruik maak van die hys-aktueerder van die vliegtuig, en die tweede is ’n direkte-lig-bygestaande beheerder wat addisioneel gebruik maak van die flappe van die vliegtuig wat as die direkte-lig aktueerder dien. Vedere beheerders is ontwerp wat die lugspoed, hoogte, klimkoers, en rolhoek van die vliegtuig reguleer asook die “Dutch roll” gedrag afklam. ’n Leiding-beheerder wat die volg van vliegbakens hanteer, is ingestel. Die landingsprosedure en -metodologie is ontwikkel wat die landingspad sowel as die sweef-pad bepaal en wat terselfdertyd ’n metode daarstel om die posisie van die landingspunt te kalibreer. Die beheerders en landingsprosedure is in ’n hardeware-in-die-lus omgewing gesimuleer en deur middel van ’n reeks proefvlugte getoets. Vyf ten volle outonome landings is uitgevoer waarvan drie van die konvensionele normaal-versnellings beheerder gebruik gemaak het, en die laaste twee die direkte-lig-bygestaande normaal-versnellings beheerder. Die vlugtoetsuitslae bevestig dat die navorsingsdoel om ’n landing binne vyf meter in lyn met en drie meter dwarsoor die landingstrook te bewerkstellig, behaal is. Hierdie akkuraatheid is verkry in beide goeie atmosferiese toestande sowel as toestande met rukwinde. Volgens die vlugtoetse blyk dit dat die direkte-lig-bygestaande normaalversnellings beheerder ’n meer akkurate landing kan bewerkstellig as die konvensionele normaal-versnellings beheerder, veral dan in toestande met rukwinde. Die direkte-ligbygestaande normaal-versnellings beheerder het ook ’n laer hei-hoek rotasie tydens die landing vertoon.

Thesis (MScEng)--Stellenbosch University, 2013. / ENGLISH ABSTRACT: In this thesis the strategy for performing System Identification on an aircraft is presented. The ultimate aim of this document is to outline the steps required for successful aircraft parameter estimation within a Fault Tolerant Control Framework. A brief derivation of the classical 6 degree-of-freedom aircraft model is firstly presented. The derivation gives insight into the aircraft dynamics that are to be used to estimate the aircraft parameters, and provides a basis for the methods provided in this thesis. Different techniques of System Identification were evaluated, resulting in the choice of the Regression method to be used. This method, based on the Least-Squares method, is chosen because of its simplicity of use and because it does not require as much computational time as the other methods presented. Regression methods, including a recursive algorithm, are then applied to aircraft parameter estimation and practical considerations such as Identifiability and corrupted measurements are highlighted. The determination of unknown measurements required for System Identification of aircraft parameters is then discussed. Methods for both estimating and measuring the Angle-of-Attack (AoA) and angular accelerations are presented. The design and calibration of an AoA probe for AoA measurements, as well as a novel method that uses distributed sensors to determine the angular accelerations is also presented. The techniques presented in this thesis are then tested on a non-linear aircraft model. Through simulation it was shown that for the given sensor setup, the methods do not provide sufficiently accurate parameter estimates. When using the Regression method, obtaining measurements of the angle-of-attack solely through estimation causes problems in the estimation of the aerodynamic lift coefficients. Flight tests were performed and the data was analyzed. Similar issues as experienced with estimation done on the non-linear aircraft simulation, was found. Recommendations with regards to how to conduct future flight tests for system identification is proposed and possible sources of errors are highlighted. / AFRIKAANSE OPSOMMING: In hierdie tesis word die strategie vir die uitvoering van Stelsel Identifikasie op 'n vliegtuig aangebied. Die uiteindelike doel van hierdie document is om die stappe wat nodig is vir 'n suksesvolle vliegtuig parameter beraming, binne 'n Fout Tolerante Beheer Raamwerk, uit eente sit. 'n Kort afleiding van die klassieke 6 graad-van-vryheid vliegtuig model word eerstens aangebied. Die afleiding gee insig in die vliegtuig dinamika wat gebruik moet word om die vliegtuig parameters te beraam, en bied 'n basis vir die metodes wat in hierdie tesis verskyn. Verskillende tegnieke van Stelsel Identifikasie is geëvalueer, wat lei tot gebruik van die regressie-metode. Hierdie metode is gekies as gevolg van sy eenvoudigheid en omdat dit nie soveel berekening tyd as die ander metodes vereis nie. Regressie metodes, insluitend 'n rekursiewe algoritme, word dan toegepas op vliegtuig parameter beraming en praktiese orwegings soos identifiseerbaarheid en korrupte metings word uitgelig. Die bepaling van onbekende afmetings wat benodig is, word vir Stelsel Identifisering van die vliegtuig parameters bespreek. Metodes om die invalshoek en hoekige versnellings te meet en beraam, word aangebied. Die ontwerp en kalibrasie van 'n invalshoek sensor vir invalshoek metings, sowel as 'n nuwe metode wat gebruik maak van verspreide sensore om die hoekversnellings te bepaal, word ook aangebied. Die tegnieke wat in hierdie tesis aangebied is, word dan op 'n nie-lineêre vliegtuig model getoets. Deur simulasie is dit getoon dat die metodes vir die gegewe sensor opstelling nie voldoende akkurate parameters beraam nie. Dit is ook bewys dat met die gebruik van die Regressie metode, die vekryging van metings van die invalshoek slegs deur skatting, probleme in die beraming van die aerodinamiese lug koëffisiente veroorsaak. Die tegnieke wat in hierdie tesis verskyn, word dan op werklike vlug data toegepas.Vlugtoetse is uitgevoer en die data is ontleed. Aanbeveling met betrekking tot hoe om toekomstige vlug toetse vir Stelsel Identifikasiete word voorgestel, en moontlike bronne van foute word uitgelig.

Thesis (MScEng)--Stellenbosch University, 2013. / ENGLISH ABSTRACT: This project concerns motion planning for a rotary wing UAV, where vehicle controllers are already in place, and map data is readily available to a collision detection module. In broad terms, the goal of the motion planning algorithm is to provide a safe (i.e. obstacle free) flight path between an initial- and goal waypoint. This project looks at two specific motion planning algorithms, the Rapidly Exploring Random Tree (or RRT*), and the Probabilistic Roadmap Method (or PRM). The primary focus of this project is learning how these algorithms behave in specific environments and an in depth analysis is done on their differences. A secondary focus is the execution of planned paths via a Simulink simulation and lastly, this project also looks at the effect of path replanning. The work done in this project enables a rotary wing UAV to autonomously navigate an uncertain, dynamic and cluttered environment. The work also provides insight into the choice of an algorithm for a given environment: knowing which algorithm performs better can save valuable processing time and will make the entire system more responsive. / AFRIKAANSE OPSOMMING: ’n Tipiese vliegstuuroutomaat is daartoe in staat om ’n onbemande lugvaartvoertuig (UAV) so te stuur dat ’n stel gedefinieerde punte gevolg word. Die punte moet egter vooraf beplan word, en indien enige verandering nodig is (bv. as gevolg van veranderinge in die omgewing) is dit nodig dat ’n menslike operateur betrokke moet raak. Vir voertuie om ten volle outonoom te kan navigeer, moet die voertuig in staat wees om te kan reageer op veranderende situasies. Vir hierdie doel word kinodinamiese beplanningsalgoritmes en konflikdeteksiemetodes gebruik. Hierdie projek behels kinodinamiese beplanningsalgoritmes vir ’n onbemande helikopter, waar die beheerders vir die voertuig reeds in plek is, en omgewingsdata beskikbaar is vir ’n konflikdeteksie-module. In breë terme is die doel van die kinodinamiese beplanningsalgoritme om ’n veilige (d.w.s ’n konflikvrye) vlugpad tussen ’n begin- en eindpunt te vind. Hierdie projek kyk na twee spesifieke kinodinamiese beplanningsalgoritmes, die “Rapidly exploring Random Tree*” (of RRT*), en die “Probabilistic Roadmap Method” (of PRM). Die primêre fokus van hierdie projek is om die gedrag van hierdie algoritmes in spesifieke omgewings te analiseer en ’n volledige analise te doen op hul verskille. ’n Sekondêre fokus is die uitvoering van ’n beplande vlugpad d.m.v ’n Simulink-simulasie, en laastens kyk hierdie projek ook na die effek van padherbeplanning. Die werk wat gedoen is in hierdie projek stel ’n onbemande helikopter in staat om outonoom te navigeer in ’n onsekere, dinamiese en besige omgewing. Die werk bied ook insig in die keuse van ’n algoritme vir ’n gegewe omgewing: om te weet watter algoritme beter uitvoertye het kan waardevolle verwerkingstyd bespaar, en verseker dat die hele stelsel vinniger kan reageer.