The design of analog and complex mixed-signal circuits in a deep submicron CMOS process technology is a big challenge. This makes it desirable to shift data converter design towards the digital domain. The advantage of using a fully digital ADC design rather than a traditional analog ADC design is that the circuit is defined by an HDL description and automatically synthesized by tools. It offers low power consumption, low silicon area and a fully optimized gate-level circuit that reduces the design costs, etc. The functioning of an all-digital ADC is based on the time domain signal processing approach, which brings a high time resolution obtained by the use of a nanometer CMOS process. An all-digital ADC design is implemented by using a combination of the digital Voltage-Controlled Oscillator (VCO) and a Time-to-Digital Converter (TDC). The VCO converts the amplitude-domain analog signal to a phase-domain time-based signal. In addition, the VCO works as a time based quantizer. The time-based signal from the VCO output is then processed by the TDC quantizer in order to generate the digital code sequences. The fully digital VCO-based ADC has the advantage of superior time resolution. Moreover, the VCO-based ADC offers a first order noise shaping property of its quantization noise. This thesis presents the implementation of a VCO-based ADC in STM 65 nm CMOS process technology using digital tools such as ModelSim simulator, Synopsys Design Compiler and Cadence SOC Encounter. The circuit level simulations have been done in Cadence Virtuoso ADE. A multi-phase VCO and multi-bit quantization architecture has been chosen for this 8-bit ADC. The power consumption of the ADC is approximately 630 μW at 1.0 V power supply and the figure of merit is around 410 fJ per conversion step.

In this thesis, the design of a scaling-friendly continuous-time closed-loop voltage controlled oscillator (VCO) based Delta-Sigma analog to digital converter (ADC) is introduced. It uses the VCO as both quantizer and integrator, and thus, obviates the need for power-hungry scaling-unfriendly operational transconductance amplifiers (OTAs) and precision comparators. It arranges two VCOs in a pseudo-differential manner, which cancels out even-order distortions. More importantly, it brings an intrinsic clocked averaging (CLA) capability that automatically addresses digital to analog converter (DAC) mismatches. The prototype ADC in 130 nm complementary metal-oxide-semiconductor (CMOS) occupies a small area of 0.03 mm² and achieves 66.5 dB signal to noise and distortion ratio (SNDR) over 2 MHz bandwidth (BW) while sampling at 300 MHz and consuming 1.8 mW under a 1.2 V power supply. It can also operate with a low analog supply of 0.7 V and achieves 65.8 dB SNDR while consuming 1.1 mW. The corresponding figure-of-merits (FOMs) for the two cases are 0.25 pJ/conversion-step and 0.17 pJ/conversion-step, respectively. / text

CMOS technology scaling has enabled dramatic improvement for digital circuits both in terms of speed and power efficiency. However, most traditional analog-to-digital converter (ADC) architectures are challenged by ever-decreasing supply voltage. The improvement in time resolution enabled by increased digital speeds drives design towards time-domain architectures such as voltage-controlled-oscillator (VCO) based ADCs. The main challenge in VCO-based ADC design is mitigating the nonlinearity of VCO Voltage-to-frequency (V-to-f) characteristics. Achieving signal-to-noise ratio (SNR) performance better than 40dB requires some form of calibration, which can be realized by analog or digital techniques, or some combination. This dissertation proposes a highly digital, reconfigurable VCO-based ADC with lookup-table (LUT) based background calibration based on "split ADC" architecture. Each of the two split channels, ADC "A" and "B", contains two VCOs in a differential configuration. This helps alleviate even-order distortions as well as increase the dynamic range. A digital controller on chip can reconfigure the ADCs' sampling rates and resolutions to adapt to various application scenarios. Different types of input signals can be used to train the ADC’s LUT parameters through the simple, anti-aliasing continuous-time input to achieve target resolution. The chip is fabricated in a 180 nm CMOS process, and the active area of analog and digital circuits is 0.09 and 0.16mm^2, respectively. Power consumption of the core ADC function is 25 mW. Measured results for this prototype design with 12-b resolution show ENOB improves from uncorrected 5-b to 11.5-b with calibration time within 200 ms (780K conversions at 5 MSps sample rate).

No description available.

Scaling of CMOS to nanometer dimensions has enabled dramatic improvement in digital power efficiency, with lower VDD supply voltage and decreased power consumption for logic functions. However, most traditionally prevalent ADC architectures are not well suited to the lower VDD environment. The improvement in time resolution enabled by increased digital speeds naturally drives design toward time-domain architectures such as voltage-controlled-oscillator (VCO) based ADCs. The major obstacle in the VCO-based technique is linearizing the VCO voltage-to-frequency characteristic. Achieving signal-to-noise (SNR) performance better than -40dB requires some form of calibration, which can be realized by analog or digital techniques, or some combination. A further challenge is implementing calibration without degrading energy efficiency performance. This thesis project discusses a complete design of a 10 bit three stage ring VCO-based ADC. A lookup-table (LUT) digital correction technique enabled by the "Split ADC" calibration approach is presented suitable for linearization of the ADC. An improvement in the calibration algorithm is introduced to ensure LUT continuity. Measured results for a 10 bit 48.8-kSps ADC show INL improvement of 10X after calibration convergence.

Les récentes avancées technologiques des microphones de type microsystème électromécanique (MEMS) leurs permettent une utilisation sur une large gamme d’amplitudes sonores. Leur niveau de bruit ayant baissé, il devient possible de capter des sons provenant d’une distance plus lointaine, tandis que l’augmentation de leur pression acoustique maximale leur permet de ne pas saturer dans un environnement très bruyant de type concert ou évènement sportif. Ainsi le système électronique de conversion analogique-numérique connecté au microphone devient l’élément limitant les performances du système d’acquisition acoustique. Un besoin de nouvelles architectures de conversion analogique-numérique ayant une plage dynamique augmentée se fait donc ressentir. Par ailleurs, ces microphones étant de plus en plus utilisés dans des systèmes fonctionnant sur batterie, la contrainte de limitation de la consommation devient importante.Dans la bande de fréquences audio, les convertisseurs analogiques-numériques de type sigma-delta sont les plus aptes à obtenir une grande résolution combinée à une faible consommation. Ils sont divisés en deux grandes familles: ceux à temps discret utilisant principalement des circuits à capacités commutées, et ceux à temps continu utilisant des circuits classiques. Cette thèse se concentre sur l’étude et la conception de chacun des deux types de convertisseurs sigma delta, en insistant sur la faible consommation, le faible coût de production (surface occupée) et la robustesse du circuit, cela en vue d’une production de masse pour équipements portables.La conception d’un convertisseur analogique numérique de type sigma-delta à temps discret a été réalisé, ce dernier atteignant un rapport signal sur bruit de 100 décibels sur une bande de 24kHz, pour une puissance consommée de seulement 480μW. Pour limiter la consommation, de nouveaux amplificateurs à base d’inverseurs sont utilisés, et dont la robustesse contre les variations du procédé de fabrication ou de la température a été améliorée. Les spécifications ont été définies grâce au développement d’un modèle de haut-niveau précis, ce qui permet d’éviter le surdimensionnement tout en atteignant les performances voulues. Enfin, un grand ratio de suréchantillonnage a été choisi afin de réduire l’espace utilisé par les capacités commutées, minimisant le coût de fabrication.Après une étude théorique de l’équivalence entre les modulateurs sigma-delta à temps discret et à temps continu, ainsi que des spécificités propres aux modulateurs à temps continu, une réalisation de ces derniers a été effectuée. Celui-ci atteint un rapport signal sur bruit de 95 décibels sur une bande de fréquence de 24kHz, tout en consommant 142μW. Pour réduire la consommation ainsi que l’espace utilisé, un filtre de boucle du second-ordre a été réalisé avec un seul amplificateur, et le quantificateur fait aussi office d’intégrateur grâce à l’utilisation d’une structure d’oscillateurs contrôlés en tension. Ce quantificateur à base d’oscillateurs est réalisé par des cellules numériques, réduisant la consommation et l’espace utilisé, mais est hautement non-linéaire. Cette non-linéarité a été prise en compte par des choix architecturaux afin de ne pas réduire les performances finales du modulateur. / The recent technological advances in microelectromechanical system (MEMS) microphones allow them to be used on a large sound amplitude range. Due to their lower noise level, it becomes possible to capture sound from a faraway distance, while their increased acoustic overload point gives them the ability to capture sound without saturation in a loud environment like a concert or a sport event. Thus, the electronic analog / digital conversion system connected to the microphone becomes the limiting element of the acoustic acquisition system performance. There is then a need for a new analog / digital conversion architecture which has an increased dynamic range. Furthermore, since more and more of these microphones are used in battery-powered devices, the power consumption limitation constraint becomes of high importance.In the audio frequency band, the sigma-delta analog / digital converters are the ones most able to provide a high dynamic range combined to a limited power consumption. They are split in two families: the discrete-time ones using switched-capacitors circuits and the continuous-time ones using more classical structures. This thesis concentrates on the study and the design of both of these two types of sigma-delta converters, with an emphasis on the low-power consumption, the low production cost (area occupied) and the circuit robustness, in sight of a mass production for portable devices.A discrete-time sigma-delta modulator design has been made, the latter reaching a signal to noise ratio of 100dB on a 24kHz frequency bandwidth, for a power consumption of only 480μW. To limit the power consumption, new inverter-based amplifiers are used, with an improved robustness against the variations of the fabrication process or the temperature. Amplifier specifications are obtained thanks to an accurate high-level model developed, which allows to avoid over-design while ensuring that the wanted performances are reached. Finally, a large oversampling ratio has been used to reduce the switched-capacitors area, lowering the modulator cost.After a theoretical study of the equivalence between discrete-time and continuous-time modulators, and of continuous-time modulators specificities, a design of the latter has been made too. It reaches a signal to noise ratio of 95dB on a 24kHz bandwidth, while consuming 142μW. To reduce the power consumption and the occupied area, a second-order loop filter is implemented using a single amplifier, and the quantizer uses a VCO-based structure that provides inherently an integrating stage. The VCO-based quantizer is made using digital cells, lowering the consumption and area, but is highly non-linear. This non-linearity has been handled by architectural choices to not influence the final modulator performances.