This report examines water supply planning issues in San Antonio, Texas. San Antonio is unique among large cities in the United States in that it relies almost exclusively on a single source, the Edwards Aquifer, for its water supply. Because San Antonio’s water demand is projected to outgrow the Aquifer’s capacity, the city must consider other options to extend and augment its current water supply. After describing the hydrogeology and water supply history of San Antonio, this report explains the multitiered water planning structure and current and future water needs for the city. It then studies and evaluates three short-to-mid term water supply options. By continuing to develop its already successful water conservation programs and water reclamation system, San Antonio can delay the need for more costly and environmentally impactful water supply options down the road, and wisely manage the resources it already draws from. / text

Microporous membranes act as selective barriers and play an important role in industrial gas separation and water purification. The permeability of such membranes is inversely proportional to their thickness. Synthetic two-dimensional materials (2DMs), with a thickness of one to a few atoms or monomer-units are ideal candidates for developing separation membranes. In this Progress Report, we present groundbreaking advances in the design, synthesis, processing, and application of 2DMs for gas and ion separations, as well as water desalination. After the introduction in Section 1, this report describes the syntheses, structures, and mechanical properties of 2DMs in Section 2. In Section 3, we will discuss the established methods for processing 2DMs into selective permeation membranes and address the separation mechanism and their performances. Finally, current challenges and emerging research directions, which need to be addressed for developing next generation separation membranes, are summarized in the Conclusion and Perspective.

The scarcity of freshwater is becoming a global challenge worldwide due to limited resources availability and increasing demand both for manufacturing and household use. For this reason, there is an important need to develop efficient, economic and sustainable desalination technologies able to take advantage of unconventional sources of water (seawater, brackish groundwater and wastewater) in order to produce freshwater. Sun is considered as the most promising abundant renewable (and free) energy source that can be employed in steam and vapor generation processes, which has a great importance in many applications such as: water desalination, domestic water heating, and power generation. This doctoral dissertation presents a study on the efficiency of different carbon based systems - nanofluids and hybrid natural composites - for the improvement of direct-solar evaporation systems, for the production of freshwater. The two main goals of this work consist of: (i) the synthesis and characterization of stable carbon-based nanofluids in water and of re-usable, economical and ecological hybrid composite materials, and (ii) the comparison of such carbon-based systems applied to water evaporation, understanding mechanisms, advantages and limitations. Carbon based materials (carbon black, graphene and multi-walled carbon nanotubes) were chosen because of their high sunlight absorption ability, unique thermal properties, as well as low cost and abundant availability. However, the hydrophobic character of such materials makes necessary to find efficient strategies to overcome this problem when dealing with water. In this work, the suspension stability of graphene-based nanofluids in water - a key parameter for the application of nanofluids in any field - was effectively improved by combining physical (by RF Sputtering coating) or chemical (by NaClO-NaBr solution) graphene surface modification treatments, and the use of common additives (Triton X-114, SDBS and gum arabic) showing different stabilization mechanisms. The best strategy to obtain long-time graphene suspension stability in water (both deionized water and saline solution with 3.5 wt% NaCl) turned out to be the combination of the easy chemical treatment with the electro-steric stabilization effect of gum arabic. In addition to nanofluids, a re-usable devices based on gum arabic cross-linked gelatin hydrogel were synthesized and characterized. Hydrophobic carbon-based materials were easily and uniformly embedded into the porous hydrogel matrix, thanks to the amphiphilic character of both gelatin and gum arabic. The effect of carbon-nanoparticles nature, morphology and concentration on the measured effective thermal conductivity of the composite material was studied and the thermal conductivity of the nanoparticles was evaluated applying several models based on the effective medium approach. The values obtained for the nanoparticles were far from the tabulated thermal conductivity values because of the combination of the composite features (such as nanoparticles concentration, Kapitza resistance) and the particles characteristics (such as aspect ratio, crystalline structure). The performance of carbon-based nanofluids and hybrid hydrogels on direct-solar evaporation of water was tested and compared to that of carbon-wood bilayer composite (which presents both hydrophilic character and natural channels for water transportation) under solar simulator. The effect of surface temperature, light-to-heat conversion efficiency of carbon-based materials, heat losses, water transport through a porous medium and suspension stability (in the case of nanofluids) were investigated in order to understand the advantages and limitations of such systems. All the tested systems were able to improve water evaporation rate and evaporation efficiency up to 70% and 82% under 1 sun and 2 suns respectively using a small amount of nanoparticles: the same amount of particles dispersed in nanofluid (0.01 wt%) was embedded into hydrogels or deposited onto wood. The high sunlight absorption ability of carbon-based nanoparticles appeared as a dominant parameter for the improvement of water evaporation rate. In fact, enhanced light absorption was directly related to a high photothermal conversion efficiency, which caused an improvement in the surface temperature, leading to a consequent enhancement in evaporation rate. It has been found that an adequate supply of water to the evaporation surface represents a fundamental parameter as well considering floating systems.

Yes / In order to improve the performance of the reverse osmosis (RO) desalination plant powered by photovoltaic (PV), two cooling systems were proposed in this study to cool the PV and preheating the RO feed water as well. In the cooling design (1), the cooling fluid flows in direct contact with the back surface of the PV through channels of half circular cross-sections. While in the design (2), it flows through channels of squar cross-sections fixed on the PV back surface. Two nano-fluids were also tested as cooling fluid: H2O/CuO and H2O/Al2O3, in addition to distilled water for the purpose of comparison. The effect of changing the weight concentration of the nano-fluid (0.05, 0.1, and 0.15%) on the PV performance was also investigated. The results showed that the PV integrated with the cooling design (1) achieves better performance compared to design (2) at all studied cooling fluids. The improvements in the electric efficiency of the PV integrated with design (1) reached 39.5, 34.8 and 27.3 % when CuO and Al2O3 nano-fluids and distilled water were used as cooling fluid, respectively, compared to the uncooled PV. Based on the obtained experimental results, the PV integrated with design (1) was selected to power the RO with H2O/CuO nano-fluid of weight concentration 0.15% and flow rate 0.15 kg/s being used as the coolant. The RO powered by the improved PV was tested at different salinities of brackish water when the preheating technique was implemented. The results showed that the proposed PV-RO desalination system produces 366 l/day when brackish water of salinity 3000 ppm was used.

This work studies the influence of field effect on large area 2 dimensional ribbons of fluids. A fluid of choice is confined in the channel of a metal-insulator-channel-insulator-metal architecture and is subjected to constant (d.c) or alternating (a.c) fields (de-pending on the application) along with a pressure drive flow. A general fluid would be composed of molecules having certain polarizability and be a dispersion of non-ionic and ionic particulates. The field effect response under pressure driven flow for this fluid would result in electrophoresis, electro osmosis, dielectrophoresis, dipole-dipole interaction and inverse electro osmosis phenomena. Using some of these phenomena we study applications related to desalination and energy harvesting with saline water as the ex-ample fluid for the former case, and solution processed poly vinyldene fluoride (PVDF) for the latter case. The geometrical features of \large area" and the \ribbon shape" can be taken advantage of to influence the design and performance for both applications. With regards to desalination, it is shown via experiments and theoretical models that the presence of alternating electric fields aid in ion separation along the flow when the saline water is subjected to laminar flow. Moreover, the power consumption is low due to the presence of the insulator. An average of 30% ion removal efficiency and 15% throughput is observed in the systems fabricated. Both performance parameters are discussion can be improved upon with larger channel lengths. The \2-D ribbon" and alternating field effect aid in achieving this by patterning the randomly distributed ions in the bulk into a smooth sheet charge and then repelling this sheet charge back into the bulk. The electric field exhibited by this sheet charge helps trap more ion sheets near the interface, thereby converting a surface ion trapping phenomena (when d.c is used) to a bulk phenomena and thereby improving efficiency. With regards to energy harvesting, a solution of PVDF in methyl ethyl ketone and 1-methyl-2-pyrollidone is confined to the \2-D ribbon" geometry and subject to high d.c fields. This aids in combining the fabrication, patterning and poling process for PVDF into one setup. Since the shape of the ribbon is defined by the shape of the channel, the ribbons (straight or serrated) can be used to sense forces of various magnitudes. More importantly experiments and theoretical models are studied for energy harvesting. Since the ribbon geometry defines the resonant frequency, large PVDF ribbon can be used to harvest energy from low frequency vibrations. Experiments show that up to 60 microwatt power can be harvested at 200 Hz and is sufficient to supplement the power for ICs.

Microporous membranes act as selective barriers and play an important role in industrial gas separation and water purification. The permeability of such membranes is inversely proportional to their thickness. Synthetic two-dimensional materials (2DMs), with a thickness of one to a few atoms or monomer-units are ideal candidates for developing separation membranes. In this Progress Report, we present groundbreaking advances in the design, synthesis, processing, and application of 2DMs for gas and ion separations, as well as water desalination. After the introduction in Section 1, this report describes the syntheses, structures, and mechanical properties of 2DMs in Section 2. In Section 3, we will discuss the established methods for processing 2DMs into selective permeation membranes and address the separation mechanism and their performances. Finally, current challenges and emerging research directions, which need to be addressed for developing next generation separation membranes, are summarized in the Conclusion and Perspective.

This project is a bachelor thesis and aims to study the integration of concentrator photovoltaics (CPV), reverse osmosis (RO) and membrane distillation (MD) for water desalination and purification. In this report, an introduction of the need for efficient water desalination is presented. Following the introduction, relevant literature has been reviewed to build up the fundamental understanding of CPV, RO and MD. A general classification of CPV subsequently introduced. In order to acquire a more comprehensive understanding of CPVs, two case studies were performed with two different types of CPV/T. The cost efficiency of each type of CPV was analysed when integrated with RO and MD systems. The result turns out to be that it was not economically beneficial to have MD in the integrated system. The reason behind is the extensive thermal energy demand of MD. Other affecting parameters, such as location and system types were also discussed. Lastly, improvements and suggestions for further studies were considered. / Detta projekt är en kandidatuppsats och syftar till att studera ett integrerande system bestående av koncentrerade solceller (CPV), omvänd osmos (RO) och membrandestillation (MD) för vattenavsaltning och rening. Rapporten börjar med en introduktion om behovet av effektiv avsaltning av vatten. Relevant litteratur har granskats för att bygga upp den grundläggande förståelsen för CPV, RO och MD. Därefter gjordes en klassificering av CPV. För att få en mer omfattande förståelse av CPV valdes två olika typer av CPV /T för en djupare undersökning. Kostnadseffektiviteten för varje CPV analyserades, när dessa var integrerade med RO- och MD-system. Resultatet visar sig att det tyvärr inte var ekonomiskt fördelaktigt att ha med MD i det integrerade systemet. Anledningen bakom detta var det omfattande termiska energibehovet för MD. Andra avgörande faktorer, såsom plats och systemtyp diskuterades tillika. Slutligen avslutades rapporten med förslag på förbättringar och områden för vidare studier.

This thesis focuses on the synthesis and characterization of various poly(arylene ether)s to improve the efficiency of gas separation and water desalination membranes. This class of polymers includes polymers such as poly(arylene ether sulfone), poly(arylene ether ketone) and poly(phenylene oxide) which offer excellent thermal and mechanical stability and usually have high enough rigidity to support gas separation and water desalination operations. Besides the plethora of properties offered by the homopolymers, these polymers can also be post-modified to cater to specific needs. For example, the polyphenylene oxides have been brominated to increase the permeability for gas separation applications. Blending is another viable method to impart desirable properties to polymers. Bisphenol A based poly(arylene ether ketone) (BPAPAEK) has been blended with commercially available poly(2,6-dimethylphenylene oxide)s (PPO) of different molecular weights in a fixed ratio (66/34 wt/wt) and in various ratios of a 22000 g/mol PPO. All the blends were UV crosslinked to minimize plasticization by condensable gases and analyzed for gel fractions, whereas, only the 22,000 g/mol blends were tested for transport properties since they yielded the highest gel fractions and exhibited the best mechanical properties. The crosslinking reduced the free volume and improved the selectivity with some drop in permeability. The blends with 90% of the 22000 g/mol PPO by weight was plotted closest to the upperbound. A phosphine oxide based poly(arylene ether ketone) (POPAEK) was blended with the various PPOs in a similar manner. The results were compared to the BPAPAEK based blends in terms of miscibility behavior and transport properties. It was found that the POPAEK based blends had higher permeability due to the higher fractional free volumes of the POPAEK. The POPAEK was more compatible with the PPOs than BPAPAEK as seen by analyzing various blend permeability models, mechanical properties and scanning electron microscope images. Moreover, blends with both the PAEKs displayed only a small drop in mechanical properties, such as the Young's modulus and the yield strength in comparison to the parent polymers. Hydroquinone based poly(arylene ether sulfone) oligomers were synthesized, post-sulfonated and chemically crosslinked to determine the effect of water uptake, fixed charge concentration and block length of oligomers on the salt permeability and the hydrated mechanical properties of the networks. The sulfonic acid groups were placed strategically and quantitatively on the hydroquinone units. The strategic placement of the acid groups may help in maintaining high rejection of monovalent ions in the presence of divalent ions, as shown in unpublished work by our group. It was found that the water uptake and fixed charge density had the opposite effects on the salt permeability. Also, the salt permeability varied differently for 5000g/mol and 10000g/mol block based networks. Another polymer that was investigated in this thesis was poly(2-ethyl-2-oxazoline) (PEtOx). An elaborate account of synthesis of monofunctional, heterobifunctional and telechelic poly(2-ethyl-2-oxazoline)s using different initiators including methyl triflate, activated alkyl halides (e.g., benzyl halides), and non-activated alkyl halides has been presented in this thesis. Endgroup functionalities and molecular weight distributions were studied by SEC, 1H NMR and titrations. The oligomers initiated with the benzyl or xylyl chloride had a PDI of 1.3-1.4 which is broader than expected for a living cationic ring opened polymer. This was attributed to the participation of covalent species which propagated slowly in the activated halide reactions. These oligomers were quantitatively terminated as proven by NMR and titrations. Due to the molecular weight distributions and quantitative termination these oligomers were deemed to be desirable for drug delivery applications. / PHD / This work pivots around the synthesis and characterization of different classes of polymers which are long molecules made by joining small molecules. The structure-property relationships of different polymers with respect to applications such as gas separation, water desalination and drug delivery were examined. The first two projects were focused of gas separation applications. Gas separation is an essential process used to recover the required gas from a mixture of gases. This process is used in a number of industries such as natural gas, hydrogen recovery and air dehumidification. In these projects, gas separation membranes were used to remove non combustible components of natural gas such as carbon dioxide and hydrogen sulfide. Two different types of poly(arylene ether ketone)s (PAEKs) (a kind of polymer) were blended with a commercial polymer called poly(phenylene oxide) (PPO) and crosslinked at the surfaces to improve the gas transport properties of the commercial polymer. PPOs have high gas permeability and a low selectivity. In other words even though the PPO membranes would alow the gasses to pass through easily, the efficiency of gas separation would be low. The blending with the PAEKs improved the selectivity of the PPOs without much loss in throughput. These blends of the two different PAEKs were compared for transport and other relavent properties. It was found that the transport properties of the commercial polymer were improved markedly without much loss in mechanical properties which are usually sacrificed upon blending of two uncomaptible polymers. Water desalination applications were looked into for a polymer class called polysulfones. About 40% of the world’s population lives in water stressed areas. In order to address the water crisis, there is a need to look beyond primitive methods such as distillation which are inefficient. Hence, the polymeric membrane separations which do not involve phase change (eg liquid to gas and then back to liquid in distillation) were examined. The currently used polyamide membranes have a rough surface because of the way they are made, making them prone to deposition of salt and organic matter. This deposition makes them inefficient. They are also prone to degradation by chlorine. The polysulfones membranes have a smoother surface less prone to these depositions. Their resistance to chlorine makes them more viable for water desalination applications. The polysulfones were post modified to introduce charges to make them more suitable for water desalination purposes. The charges repelled the ions of same polarity and made the polymer more hydrophilic. However, as the number of charges increased, the water uptake of the polymer increased which resulted in a decrease in the effectiveness of salt /ion rejection. To increase the charge density of the polymers by (the effectiveness of ion rejection), the polymer chains were crosslinked at the ends. For deleniating the structure property relationships, the amount of charges were varied and two sets of chain lengths were studied. The salt permeability decreased with increase in fixed charge concentration and decrease in water uptake. Poly(2-Oxazolines), were investigated as potential drug delivery vehicles. Polymeric drug delivery vehicles have been used to control the rate of release of drugs in the body to avoid side effects. Another advantage of polymeric drug delivery systems is making the water insoluble drugs more compatible with the fluids in the body. Currently, polyethylene oxides are being used as drug delivery vehicles. However, these polymers have been known to produce antibodies in some people. In this work, poly(2-oxazolines) which are known to be more compatible with human body than PEOs were prepared using different initiators and end cappers to prepare an elaborate repertoire of controlled molecular weight and controlled functionality oligomers for further modification.