Two main subjects are addressed in this study. The ability of a bright red material with metallic behaviour to be used as a visible light photocatalyst for hydrogen evolution and the feasibility of visible light photocatalytic water splitting using Z-schemes constituted from different kinds of photocatalysts and materials used as mediators. Strontium niobate (Sr₁₋ₓNbO₃) is an A-site deficient perovskite with intense red colour. It is an unusual material that displays both metallic type conduction and- as we present- photocatalytic activity. Specifically, photocatalytic visible light hydrogen production with oxalic acid as a sacrificial reagent is achieved from this material even without the need for a co-catalyst or other alteration. This photocatalytic activity is screened with time and related to different parameters that might influence it, like crystal structure, surface area and surface chemistry. The crystal structure of strontium niobate is A site stoichiometry dependant and the materials acquires a cubic symmetry for Sr≤ 0.92 and orthorhombic for 0.92≤ Sr≤ 0.97. The change of crystal structure from cubic to orthorhombic symmetry seems to have a negative effect on the photocatalytic activity, as the NbO₆ octahedra become distorted and unfavourable for d-orbital overlapping. The highest photocatalytic activity is exhibited at the turning point of one structure to the other. Increase in the photocatalytic activity is also exhibited by enlarging the surface area through ball milling, nevertheless, a clear trend for surface area effect on activity is not obtained among samples with different Sr content. Additionally, an enrichment of Sr on the surface of strontium niobate is observed by XPS, which apart from the fact that seems to be a governing factor improving stability it is also considered a key point for the exhibited photocatalytic activity altogether. Full water splitting under visible light from Z-schemes is studied by fabricating three general categories of systems. These three different categories depend on the mediator used to fabricate the Z-schemes and are: redox couple Z-schemes (with Fe⁺³/Fe⁺²), solid mediator Z-schemes (with GO) and no mediator Z-schemes. The materials used as photocatalysts for the fabrication of the Z-schemes are: Sr₀.₉₂NbO₃ for hydrogen production and both WO₃ and BiVO₄ independently for oxygen production. The photocatalytic activity for water splitting is evaluated in production of hydrogen and oxygen with time and the ratio of their production rates is frequently checked to see whether the ideal hydrogen to oxygen 2:1 is achieved. The general idea acquired from the results of all the three types of systems is that, water splitting with Z-schemes is a complicated process and in most cases governed by many subreactions. More specifically, in all cases of redox couple Z-schemes we got hydrogen to oxygen ratio imbalances and with the most prominent one being the lack of hydrogen production. Thankful is the fact that a certain type of system, the one consisting of WO₃ as oxygen photocatalyst and Fe⁺² as initial mediator species gives results very close to the ideal one and with a high degree of reproducibility indicating this way the probable formation of a Z-scheme that has overcome more of the imbalances. In between the two other categories, solid mediator and no mediator Z-schemes, subreactions seem to be the governing factor hence imbalances are always present. A case study in the no mediator Z-schemes on an attempt to investigate sources of imbalances, reveals that a big source of imbalance is most probably from the trapping of protons from WO₃.

Water splitting through photoelectrochemical reaction is widely regarded as a major method to generate H2 , a promising source of renewable energy to deal with the energy crisis faced up to human being. Efficient exploitation of visible light in practice of water splitting with pure TiO2 material, one of the most popular semiconductor material used for photoelectrochemical water splitting, is still challenging. One dimensional TiO2 nanotubes is highly desired with its less recombination with the short distance for charge carrier diffusion and light-scattering properties. This work is based on TiO2 NTPC electrode by the optimized two-step anodization method from our group. A highly crystalized p-type Cu2O layer was deposited by optimized pulse potentiostatic electrochemical deposition onto TiO2 nanotubes to enhance the visible light absorption of a pure p-type TiO2 substrate and to build a p-n junction at the interface to improve the PEC performance. However, because of the real photocurrent of Cu2O is far away from its theoretical limit and also poor stability in the aqueous environment, a design of rGO medium layer was added between TiO2 nanotube and Cu2O layer to enhance the photogenerated electrons and holes separation, extend charge carrier diffusion length (in comparison with those of conventional pure TiO2 or Cu2O materials) which could significantly increase photocurrent to 0.65 mA/cm2 under visible light illumination (>420 nm) and also largely improve the stability of Cu2O layer, finally lead to an enhancement of water splitting performance.

Tin disulfide (SnS2) is a two-dimensional (2D) material with excellent properties and high prospects for low-cost solutions to catalytic and optoelectronic applications. In this work, vertical nanoflakes of SnS2 have been synthesized using custom-designed close space sublimation (CSS) system and investigated for applications in photoelectrochemical (PEC) water oxidation and metal-semiconductor-metal (MSM) photodetector. For the PEC application, vertical SnS2 nanoflakes grown directly on transparent conductive substrates have been used as photoanodes, which produce record photocurrents of 4.5 mA cm−2 for oxidation of a sulfite hole scavenger and 2.6 mA cm−2 for water oxidation without any hole scavenger, both at 1.23 VRHE in neutral electrolyte under simulated AM1.5G sunlight, and stable photocurrents for iodide oxidation in acidic electrolyte. This remarkable performance has been attributed to three main reasons: (1) high intrinsic carrier mobility of 330 cm2 V−1 s−1 and long photoexcited carrier lifetime of 1.3 ns in the nanoflakes, (2) the nanoflake height that balances the competing requirements of light absorption and charge transport, and (3) the unique stepped morphology of these nanoflakes that improves photocurrent by exposing multiple edge sites in every nanoflake. In another application, these SnS2 nanoflakes have been used to enhance the performance of lead sulfide quantum dot (PbS QDs) photodetectors by providing a high-mobility channel for photoexcited charges from PbS QDs, which results in 2 orders of magnitude enhancement in responsivity. The physical models and experimental findings presented in this dissertation can help engineer more cost-effective solutions for PEC water splitting and optoelectronics based on 2D metal dichalcogenides.

This thesis comprises an assessment of a novel concept to produce high purity hydrogen using mixed oxide ion/electronic conductor (MIEC) membranes and energy provided by solar concentrators (i.e. parabolic troughs or parabolic dishes). The vision of this concept is that it will be used to produce tons of high purity hydrogen for fuel cells, which is a scarce commodity with an increasing demand from residential and transportation power generation applications. The MIEC membrane activates a steam reforming reaction between water and methane to produce hydrogen of high purity on the water side and syngas on the fuel side. Expectations are that this concept has cost advantages over other thermo-chemical water-dissociation methods, using a lower temperature and no electricity for the reaction process. The thesis’ focus is on techno-economic aspects of the concept, as part of an application process for project financing by the European Commission of Research and Innovation. The assessment in the thesis shows that the overall efficiency of the concept is expected to be very low. It also identifies the difficulties of providing stable working conditions for the concept. Suggestions to improve the concept are proposed to address the most urgent problems of the concept. These suggestions illuminate the opportunities that actually do exist to combine MIEC membranes, solar energy and thermo-chemical water splitting into a working concept. These improvements include using parabolic dishes instead of parabolic troughs, using furnaces with control systems and using a viable flow rate. The production capacity of high purity hydrogen is expected to be approximately 89 mg per minute in a membrane bundle (i.e. 150 thin membrane fibers with an oxygen permeation flux of 1 ml cm-2 min-1) if these improvements were implemented. This would imply that the studied concept needs further development to produce high purity hydrogen in quantities that could meet the shortage on the commercial fuel cell markets.

This thesis concerns the development and the study of Iron-based water oxidation catalysts (WOCs) and how to immobilize them onto the hydrophobic surface of a carbon paste electrode. In the introductory chapter a general background of the field of water splitting and this thesis is given. In the second chapter, experimental performance is described from synthesis to measurements of a complete complex-doped electrode. The third chapter deals with the results and the discussion of the performed experiments. In chapter four, a descriptive conclusion of the obtained data is held. / Det här arbetet berör studien och utvecklingen utav järnbaserade katalysatorer, speciellt framtagna för för delning utav vatten. Utöver detta undersöks även om dessa katalysatorer (WOCs) kan immobiliseras på den hydrofoba ytan hos elektroder gjorda på kol-pasta. I det inledande kapitlet ges en generell bakgrund till området som berör delning utav vatten. I det andra kapitlet presenteras det experimentella utförandet utav synteser samt elektrokemiska mätningar som berörts under arbetets gång i jakten på en komplexdopad elektrod. I det tredje kapitlet diskuteras resultaten från mätningarna samt möjliga framtidsutsikter. I det fjärde kapitlet presenteras slutsatserna utav studien.

京都大学 / 新制・課程博士 / 博士(工学) / 甲第23216号 / 工博第4860号 / 新制||工||1759(附属図書館) / 京都大学大学院工学研究科物質エネルギー化学専攻 / (主査)教授 阿部 竜, 教授 陰山 洋, 教授 藤田 晃司 / 学位規則第4条第1項該当 / Doctor of Philosophy (Engineering) / Kyoto University / DGAM

Philosophiae Doctor - PhD / The widespread use of fossil energy has been most convenient to the world, while they also cause environmental pollution and global warming. Therefore, it is necessary to develop clean and renewable energy sources, among which, hydrogen is considered to be the most ideal choice, which forms the foundation of the hydrogen energy economy, and the research on hydrogen production and fuel cells involved in its production and utilization are naturally a vital research endeavor in the world. Electrocatalysts are one of the key materials for proton exchange member fuel cells (PEMFCs) and water splitting. The use of electrocatalysts can effectively reduce the reaction energy barriers and improve the energy conversion efficiency.

<p><strong>Apstrakt je obrađen tehnologijama za optičko prepoznavanje teksta (OCR).</strong></p><p>Cilj ovog rada je teorijska (računarska) analiza primenljivosti dvomembranskog reaktora za izvodenje povratnih gasnih reakcija. Specijalno, analizira se primenljivost dvomern- branske konhguracije za termolizu vode. Rezultati simulacije su pokazali značajnu pred- nost, u pogledu povečanja konverzije reaktanta iznad ravnotežne, dvomembranske u odnosu na jednomembransku konhguraciju, u slučaju kada su membrane najmanje pro- pustljive za reaktant. Rezultati neizotermske analize dvomembranskog reaktora su pokazali da je efekat energije aktivacije u odnosu na efekat toplote reakcije zanemarljiv, u oblasti vehkih Damk&ouml;hler-ovih brojeva (odnos maksimalne brzine reakcije i protoka reaktanta u napoju). I za endotermne i za egzotermne reakcije, konverziona efikasnost opada sa porastom indeksa generisanja toplote (odnos toplotnog efekta reakcije i toplotnog kapaciteta reaktanta), a raste sa intenzitetom dovodenja odnosno odvodenja toplote. &Scaron;to se tiče uticaja temperature napoja, kod endotermnih reakcija postoji optimum ako permeabilnosti komponenata opadaju sa temperaturom. Na bazi raspoloživih literaturnih podataka formulisan je izotermski model dvomembranskog reaktora za termolizu vode sa jednom membranom propustljivom za vodonik, a drugom propustljivom za kiseonik. Pokazano je da se pri dovoljno velikim vrednostima Damk&ouml;hler-ovih broja i odnosa brzina (odnos maksimalne brzine permeacije za membranu i maksimalne brzine reakcije) u reaktoru može postići potpuna disocijacija vode. Zapaženo je postojanje optimalne raspodele ukupnog odnosa brzina izmedu dve membrane kao i, u slučaju uvodenja inerta u separacionu zonu, optimalne raspodele inerta između dve zone. Analiza je pokazala da dvomembranski reaktor predstavlja perspektivno re&scaron;enje problema termolize vode koje zaslužuje dalja teorijska i eksperimentaina istraživanja.</p> / <p><strong>Abstract was processed by technology for Optical character recognition (OCR).</strong></p><p>The aim of this study is a theoretical (computer) analysis of the applicability of a double-membrane reactor for reversible gas phase reactions. Particulaidy, the applicability of double-membrane configuration for the direct thermal water splitting is studied. The double-membrane configuration proved to be significantly superior over the single membrane configuration with respect to the equilibrium shift, in the case when the reac- tant is the slowest permeating component. By the non-isothermal analysis, it is shown that, in the region of high Damk&ouml;hler numbers (the ratio of the maximal reaction rate to the feed reactant flow), the effect of activation energy is negligible when compared to the effect of reaction heat. The conversion efficiency is decreasing by the increase of the heat generation index (the ratio of reaction heat to reactant heat capacity) and increasing by the increase of the added or removed heat, for both endo- and exothermic processes. As to the feed temperature, an optimal value exists for endothermic reactions, if component permeabilities are decreasing functions of temperature. On the basis of the available literature data, the isothermal model of double-membrane reactor (one membrane permeable for hydrogen an the other for oxygen) for direct thermal splitting of water is formulated. It is shown that the complete water dissociation could be achieved at the high enough values of Damk&ouml;hler number and of the rate ratio (the ratio of maximal permeability of membrane to the maximal reaction rate). The optimal distribution of the total rate ratio between the membranes as well as the optimal inert flow distribution could be determined. Double-membrane configuration seems to be a promising solution for the problem of direct thermal water splitting, deserving further theoretical and experimental investigations.</p>

Conversion of renewable energy resources (such as solar and wind) through water splitting to hydrogen and oxygen has attracted increasing attention. The sole product of hydrogen combustion is water, rendering a carbon-neutral energy cycle. Water splitting consists of two redox half reactions: hydrogen evolution reaction (HER) and oxygen evolution reaction (OER). Both of these two transformations involve multi- electron/proton movement and thus are kinetically sluggish. In order to accelerate the reaction rates for practical application, efficient catalysts are needed. State-of-the-art catalysts for water splitting are usually composed of noble metals, such as platinum, ruthenium, and iridium, whose scarcity and high cost limit their wide employment. Consequently, it is of critical importance to develop competent and non-precious catalysts via low-cost preparation. Owing to the thermodynamic convenience and potential application in proton exchange membrane and alkaline electrolyzers, traditionally, most HER catalysts were developed under strongly acidic conditions while OER catalysts under strongly alkaline conditions. In order to accomplish overall water splitting, the coupling of HER and OER catalysts in the same electrolyte is mandatory. This thesis will summarize our recent efforts towards developing 1st-row transition metal-based sulfides and phosphides for electrocatalytic water splitting under ambient conditions.

The booming worldwide demand for energy and the increasing concerns about global warming due to fossil fuel consumption have urged the development of techniques for storing and converting renewable and clean energy resources. Electrocatlytic or photoelectrocatalytic water splitting to generate green energy carrier H2 with sustainable energy input, like solar, has been regarded as an attractive strategy for carbon-neutral energy needs. However, the sluggish kinetics for both half reactions (HER and OER), high overpotentials and thermodynamic requirements, and H2 and O2 gas crossover have been regarded as the major challenges, which limit its widespread application. On account of high efficiency and fast reaction rate, proton exchange membrane electrolyzer (PEME) has been developed as a mature technology for water splitting under acidic conditions. Nonetheless, it requires noble metals as robust and competent catalysts (like Pt for HER and IrO2 for OER), which is economically unfavorable. Owing to the thermodynamic convenience for OER and the integration of HER and OER in the same electrolyte, anion exchange membrane electrolyzer (AEME) has also been explored under alkaline conditions, utilizing first-row transition metals as bifunctional catalysts. However, for both PEME and AEME, H2 and O2 are generated simultaneously. Even though “gas impermeable” membranes are employed, the formation of H2/O2 mixture is inevitable. So one part of my research introduced a new strategy to couple HER with more thermodynamically favorable biomass-derived upgrading in alkaline solution, which requires lower energy input than overall water splitting and produces more valuable and non-gas products. However, the solubility of biomass-derived organic compounds as well as the competing reaction of water oxidation limits the catalytic current density. Therefore, we further introduce the concept of redox mediator (RM) to divide conventional water splitting into two separate steps. This allows H2 and O2 to be produced at different times as well as in different spaces and reduces the energy input required to conduct a productive step. This strategy not only prevents H2/O2 mixing but also reduces the voltage input as the redox potential of RM+/0 will be within the HER and OER thermodynamic potentials, hence allowing water splitting to be driven by photovoltaic cells with small photovoltage.