"December, 2003" / Includes bibliographical references (p. 311-348) / Accompanying CD-ROM entitled: 'SPM_PhD_Thesis' contains MATLAB_Algorithms (algorithms for T-ray data analysis and display, as described in the Thesis); Appendix D (Example_Raw_Data_Files - examples of raw T-ray data files, used by the MATLAB algorithms in MATLAB_Algorithms); and Thesis_PDF (a copy of the Thesis printed in Adobe's Portable Document Format (PDF)). / System requirements for accompanying CD-ROM: CD-ROM drive ; Adobe Acrobat reader ; Matlab software. / xxxiv, 358 p. : ill. (col.) ; 30 cm. + 1 CD-ROM (col. ill. ; 4 3/4 in.) / Title page, contents and abstract only. The complete thesis in print form is available from the University Library. / Thesis (Ph.D.)--University of Adelaide, School of Electrical and Electronic Engineering, 2004

No description available.

No description available.

The propagation of acoustic plate-mode waves in composite membranes is studied. A computer program has been developed and used to calculate the wave velocity and electromechanical coupling factor in these structures which may consist of any combination of piezoelectric layers with arbitrary orientation and surface metallization. In particular, shear modes (SH) in zinc-oxide and selenium membranes, as well as stiffened-Lamb modes in ZnO membranes and ZnO/Si, ZnO/GaAs composite membranes are studied. / The surface-acoustic-wave propagation in selenium and in selenium layers on tellurium has been extensively studied using an improved computer program. The study shows that surface-wave coupling factors in the range of 0.5 to 1.5% are possible with these structures. The calculated sensitivity of the velocity and coupling factor to errors in material constants shows that an accurate value of the e(,11) constant for selenium is necessary for an accurate estimate of the coupling factor. / A technology for fabricating selenium-tellurium layered structures for SAW propagation has been successfully developed. Measurements on fabricated SAW delay lines were carried out and estimates of the coupling factor and the acoustic attenuation obtained. These measurements, taken together with previously published results, confirm that the published value of e(,11) = 0.32 C/m('2) is too small.

This thesis discusses the design, fabrication, integration and characterization of millimeter wave passive components using polymer-core-conductor surface micromachining technologies. Several antennas, including a W-band broadband micromachined monopole antenna on a lossy glass substrate, and a Ka-band elevated patch antenna, and a V-band micromachined horn antenna, are presented. All antennas have advantages such as a broad operation band and high efficiency. A low-loss broadband coupler and a high-Q cavity for millimeter-wave applications, using surface micromachining technologies is reported using the same technology. Several low-loss all-pole band-pass filters and transmission-zero filters are developed, respectively. Superior simulation and measurement results show that polymer-core-conductor surface micromachining is a powerful technology for the integration of high-performance cavity, coupler and filters. Integration of high performance millimeter-wave transceiver front-end is also presented for the first time. By elevating a cavity-filter-based duplexer and a horn antenna on top of the substrate and using air as the filler, the dielectric loss can be eliminated. A full-duplex transceiver front-end integrated with amplifiers are designed, fabricated, and comprehensively characterized to demonstrate advantages brought by this surface micromachining technology. It is a low loss and substrate-independent solution for millimeter-wave transceiver integration.

"December, 2003" / Includes bibliographical references (p. 311-348) / Accompanying CD-ROM entitled: 'SPM_PhD_Thesis' contains MATLAB_Algorithms (algorithms for T-ray data analysis and display, as described in the Thesis); Appendix D (Example_Raw_Data_Files - examples of raw T-ray data files, used by the MATLAB algorithms in MATLAB_Algorithms); and Thesis_PDF (a copy of the Thesis printed in Adobe's Portable Document Format (PDF)). / System requirements for accompanying CD-ROM: CD-ROM drive ; Adobe Acrobat reader ; Matlab software. / xxxiv, 358 p. : ill. (col.) ; 30 cm. + 1 CD-ROM (col. ill. ; 4 3/4 in.) / Title page, contents and abstract only. The complete thesis in print form is available from the University Library. / Thesis (Ph.D.)--University of Adelaide, School of Electrical and Electronic Engineering, 2004

Thesis (Ph. D.)--Ohio State University, 2007. / Title from first page of PDF file. Includes bibliographical references (p. 102-106).

Thesis (Ph.D.)--University of Adelaide, School of Electrical and Electronic Engineering, 2004. / "December, 2003" Includes bibliographical references (p. 311-348).

Thesis (Ph.D.)--University of Adelaide, School of Electrical and Electronic Engineering, 2005. / Includes bibliographical references (p. 349-379) and index.

Thesis (Ph. D.)--State University of New York at Binghamton, Mechanical Engineering Department, 2006. / Includes bibliographical references.