Because of the huge bandwidth of Ultra-Wideband (UWB) systems, in-band narrowband interference may hinder receiver performance. In this dissertation, sources of potential narrowband interference that lie within the IEEE 802.15.3a UWB bandwidth are presented, and a solution is proposed. To combat interference in Multi-Band OFDM (MB-OFDM) UWB systems, an analog notch filter is designed to be included in the UWB receive chain. The architecture of the filter is based on feed-forward subtraction of the interference, and includes a Least Means Squared (LMS) tuning scheme to maximize attenuation. The filter uses the Fast Fourier Transform (FFT) result for interference detection and discrete center frequency tuning of the filter. It was fabricated in a 0.18 µm process, and experimental results are provided. This is the first study of potential in-band interference sources for UWB. The proposed filter offers a practical means for ensuring reliable UWB communication in the presense of such interference. The Operational Transconductance Amplifier (OTA) is the predominant building block in the design of the notch filter. In many cases, OTAs must handle input signals with large common mode swings. A new scheme for achieving rail-to-rail input to an OTA is introduced. Constant gm is obtained by using tunable level shifters and a single differential pair. Feedback circuitry controls the level shifters in a manner that fixes the common mode input of the differential pair, resulting in consistent and stable operation for rail-to-rail inputs. As the new technique avoids using complimentary input differential pairs, this method overcomes problems such as Common Mode Rejection Ratio (CMRR) and Gain Bandwidth (GBW) product degradation that exist in many other designs. The circuit was fabricated in a 0.5µm process. The resulting differential pair had a constant transconductance that varied by only ±0.35% for rail-to-rail input common mode levels. The input common mode range extended well past the supply levels of ±1.5V, resulting in only ±1% fluctuation in gm for input common modes from -2V to 2V.

Optical communications is expanding into new applications such as infrared wireless communications; therefore, designing high performance circuits has gained considerable importance. In this dissertation a wide dynamic-range variable-gain transimpedance amplifier (TIA) is introduced. It adopts a regulated cascode (RGC) amplifier and an operational transconductance amplifier (OTA) as the feed forward gain element to control gain and improve the overload of the optical receiver. A fully-differential variable-gain TIA in a 0.35µm CMOS technology is realized. It provides a bit error rate (BER) less than 10-12 for an input current from 6µA-3mA at 3.3V power supply. For the transimpedance gain variation, from 0.1kΩ to 3kΩ, -3dB bandwidth is higher than 1.7GHz for a 0.6pF photodiode capacitance. The power dissipations for the highest and the lowest gains are 8.2mW and 24.9mW respectively. A new technique for designing uniform multistage amplifiers (MA) for high frequency applications is introduced. The proposed method uses the multi-peak bandwidth enhancement technique while it employs identical, simple and inductorless stages. It has several advantages, such as tunability of bandwidth and decreased sensitivity of amplifier stages, to process variations. While all stages of the proposed MA topology are identical, the gain-bandwidth product can be extended several times. Two six-stage amplifiers in a TSMC 0.35µm CMOS process were designed using the proposed topology. Measurements show that the gain can be varied for the first one between 16dB and 44dB within the 0.7-3.2GHz bandwidth and for the second one between 13dB and 44dB within a 1.9-3.7GHz bandwidth with less than 5.2nV/√Hz noise. Although the second amplifier has a higher gain bandwidth product, it consumes more power and occupies a wider area. A technique for capacitance multiplication is utilized to design a tunable loop filter. Current and voltage mode techniques are combined to increase the multiplication factor (M). At a high input dynamic range, M is adjustable and the capacitance multiplier performs linearly at high frequencies. Drain-source voltages of paired transistors are equalized to improve matching in the current mirrors. Measurement of a prototype loop filter IC in a 0.5µm CMOS technology shows 50µA current consumption for M=50. Where 80pF capacitance is employed, the capacitance multiplier realizes an effective capacitance varying from 1.22nF up to 8.5nF.

Thesis (M. Phil.)--Hong Kong University of Science and Technology, 2003. / Includes bibliographical references (leaves 68-72). Also available in electronic version. Access restricted to campus users.

The thesis report presents the designs of compact planar ultra-wideband (UWB) antennas for wireless devices applications. Three main designs of UWB antennas are studied, namely, single UWB antennas, UWB multiple-input-multiple-out(MIMO)antennas, and transparent UWB antennas on the screens of mobile phones. For single UWB antennas, the designs of two compact planar monopole antennas with compact sizes of 26×28 mm2and 30×39.3mm2are presented. The UWB operations of the antennas are achieved using a ground slot under the feed line, offsetting the feed line and the radiator from the middle of the ground plane and smoothly transforming the feed line. Simulation and measurement show that the two antennas can achieve an ultra-wide bandwidth with approximately omnidirectional patterns. A deep notch-band in5.1-5.85 GHz is created in one of the UWB antennas by employing two pairs of meander lines (MLs), one pair being close to the feed line and the other pair along the upper edge of the ground plane. At the notch frequency, the simulated efficiency is only 4%. Three compact UWB-MIMO antennas with very compact sizes of 26×40 〖mm〗^2, 21×38 〖mm〗^2, and 22×36 〖mm〗^2 are designed. Each of them is designed using two UWB antenna elements perpendicularly or symmetrically placed. Different techniques such as using ground stubs besides the radiators, cutting inclined slots on the ground, and adding a T-shaped protruding from ground are proposed to lower mutual coupling between the two antenna elements. One of the antennas is designed to generate a notched band in 5.15-5.85 GHz using two ground strips. Simulation and measurement results show that these antennas can cover the entire UWB of 3.1-10.6GHz with mutual coupling of less than -15 dB, and envelope correlation coefficient of less than 0.1. An UWB antenna is designed using a transparent conductive film for applications on mobile phone screens. The effects of a finger touching the screen are studied. Results show that, with the radiator on the bottom side of the screen and a thin film with a thickness of 0.05 mm on the top side to separate the finger and the antenna, the effects of the finger can be minimized. In measurement of monopole antennas with small ground planes, due to the feeding cable used, there are always discrepancies between the simulated and measured results in radiation patterns, efficiencies, and gains at lower frequencies. To verify that the discrepancies in the results of these studies are indeed due to the feeding cable used in measurement, the models of the feeding cables are developed and used for simulation. Results show that, by using the cable model, the simulated and measured results in radiation patterns, efficiencies, and gains agree very well. / published_or_final_version / Electrical and Electronic Engineering / Doctoral / Doctor of Philosophy

Not available / text

published_or_final_version / abstract / toc / Electrical and Electronic Engineering / Master / Master of Philosophy

In recent years, ultra-wideband (UWB) communications has gained tremendous popularity in both research community and industry. The large bandwidth of UWB systems raises new wireless channel effects and consequently unique advantages as well as challenges to be dealt with, compared to conventional wireless systems. One of these advantages is the ability to resolve dense multipath components and use Rake combining at the receiver in order to significantly reduce the negative effects of fading. However, implementing a Rake receiver with a sufficiently large number of fingers to make use of this advantage is an evident challenge for most UWB devices with limited signal processing capabilities. A possible approach to overcome this problem is to move computational complexity from the receiver to the more powerful transmitter, which is the main focus of the present work. In this thesis, we propose two novel pre-equalization schemes for multiple- input single-output (MISO) direct-sequence ultra-wideband (DS-UWB) systems with pre-Rake combining and symbol-by-symbol detection. The first pre-equalization filter (PEF) scheme employs one PEF per transmit antenna, whereas in the second, simplified PEF (S-PEF) scheme all transmit antennas share the same PEF. For both schemes the optimum finite impulse response (FIR) and infinite impulse response (IIR) PEFs are calculated based on the minimum mean squared error (MMSE) criterion. We show that in contrast to previously proposed schemes for DS-UWB, both our proposed PEF schemes efficiently exploit the channel shortening properties of the pre-Rake filter. In particular, our proposed PEF schemes operate at the symbol level. We also show that under certain conditions the S-PEF scheme achieves the same performance as the more complex PEF scheme. Finally, we demonstrate that a single-input multiple-output (SIMO) DS-UWB system with post-Rake combining and MMSE post-equalization is the dual system to the considered MISO DS–UWB system with pre-Rake combining and MMSE pre-equalization. This uplink-downlink duality can be exploited for efficient calculation of the PEFs and for complexity reduction. Our simulation results show that the proposed PEF schemes achieve significant performance gains over pre-Rake combining without equalization even if only short PEFs are employed, and this is the case even for long UWB channel impulse responses.

Ray tracing based on geometric optics can be utilized for generating propagation models for arbitrary and complex environments. These methods can be employed to determine important wireless channel characteristics such as path gain and the channel impulse response which in turn can be used to deduce channel capacity. In this thesis, a fully vectorial 3-D ray-tracer is developed. The simulator is applied to study novel wireless systems such as ultra-wideband pulse propagation in complex railway tunnels and MIMO systems employing closely spaced low mutual coupling meta-material antennas. The computational complexity of the ray-tracing algorithm is reduced using optimizations and via the development of a novel hybrid method that combines the efficiency and accuracy of waveguide models with the flexibility of a ray-tracer. The resulting simulator is validated against measured results and demonstrated to show good agreement. Convergence of the solution using the ray-tracing method is also discussed.

Ray tracing based on geometric optics can be utilized for generating propagation models for arbitrary and complex environments. These methods can be employed to determine important wireless channel characteristics such as path gain and the channel impulse response which in turn can be used to deduce channel capacity. In this thesis, a fully vectorial 3-D ray-tracer is developed. The simulator is applied to study novel wireless systems such as ultra-wideband pulse propagation in complex railway tunnels and MIMO systems employing closely spaced low mutual coupling meta-material antennas. The computational complexity of the ray-tracing algorithm is reduced using optimizations and via the development of a novel hybrid method that combines the efficiency and accuracy of waveguide models with the flexibility of a ray-tracer. The resulting simulator is validated against measured results and demonstrated to show good agreement. Convergence of the solution using the ray-tracing method is also discussed.

No description available.