Comparative studies of nondestructive evaluation methods have shown that nonlinear ultrasonic techniques are more sensitive than conventional linear methods to changes in material microstructure and the associated small-scale damage. Many of the material degradation processes such as carbonation in concrete, corrosion in metals, etc., begin at the surface. In such cases, ultrasonic Rayleigh surface waves are especially appropriate for detection and characterization of damage since their energy is concentrated in the top layer of the test object. For the civil engineering infrastructure, only a limited number of field applicable nonlinear ultrasonic techniques have been introduced. In this paper a nonlinear ultrasonic measurement technique based on the use of Rayleigh waves is developed and used to characterize carbonation in concrete samples. Wedge transducer is used for the generation and an accelerometer for detection of the fundamental and modulated ultrasonic signal components. The measurements are made by varying the input voltage and along the propagation distance. The slope of the normalized modulated amplitudes is taken as the respective nonlinearity parameter. Concrete samples with two different levels of damage are examined, and the difference of the two fundamental frequencies is used to quantify damage state.

Velocity-coupled combustion instability is a major issue facing lean combustor design in modern gas turbine applications. In this study, we analyze the complex acoustic field excited by a transverse acoustic mode in an annular combustor. This work is motivated by the need to understand the various velocity disturbance mechanisms present in the flame region during a transverse instability event. Recent simulation and experimental studies have shown that much of the flame response during these transverse instabilities may be due to the longitudinal motion induced by the fluctuating pressure field above the nozzles. This transverse to longitudinal coupling has been discussed in previous work, but in this work it is given a robust acoustic treatment via computational methods in order to verify the mechanisms by which these two motions couple. We will provide an in-depth discussion of this coupling mechanism and propose a parameter, Rz, also referred to as the Impedance Ratio, in order to compare the pressure/velocity relationship at the nozzle outlet to quasi one-dimensional theoretical acoustic approximations. A three-dimensional inviscid simulation was developed to simulate transversely propagating acoustic pressure waves, based on an earlier experiment designed to measure these effects. Modifications to this geometry have been made to account for lack of viscosity in the pure acoustic simulation and are discussed. Results from this study show that transverse acoustic pressure excites significant axial motion in and around the nozzle over a large range of frequencies. Furthermore, the development of Rz offers a defined physical parameter through which to reference this important velocity-coupled instability mechanism. Therefore, this study offers an in-depth and quantifiable understanding of the instability mechanism caused by transversely propagating acoustic waves across a combustor inlet, which can be applied to greatly improve annular combustor design in future low-emissions gas turbine engines.

The object of this research was to investigate dispersion in surface phononic crystals (PnCs) for application to a newly developed passive surface acoustic wave (SAW) ozone sensor. Frequency band gaps and slow sound already have been reported for PnC lattice structures. Such engineered structures are often advertised to reduce loss, increase sensitivity, and reduce device size. However, these advances have not yet been realized in the context of surface acoustic wave sensors. In early work, we computed SAW dispersion in patterned surface structures and we confirmed that our finite element computations of SAW dispersion in thin films and in one dimensional surface PnC structures agree with experimental results obtained by laser probe techniques. We analyzed the computations to guide device design in terms of sensitivity and joint spectral operating point. Next we conducted simulations and experiments to determine sensitivity and limit of detection for more conventional dispersive SAW devices and PnC sensors. Finally, we conducted extensive ozone detection trials on passive reflection mode SAW devices, using distinct components of the time dispersed response to compensate for the effect of temperature. The experimental work revealed that the devices may be used for dosimetry applications over periods of several days.

The analysis and development of robust sensing platforms based on solidly-mounted ZnO bulk acoustic wave devices was proposed. The exploitation of acoustic energy trapping was investigated and demonstrated as a method to define active sensing areas on a substrate. In addition, a new "hybrid" acoustic mode experiencing acoustic energy trapping was studied theoretically and experimentally. This mode was used as an explanation of historical inconsistencies in observed thickness-shear mode velocities. Initial theoretical and experimental results suggest that this mode is a coupling of thickness-shear and longitudinal particle displacements and, as such, may offer more mechanical and/or structural information about a sample under test. Device development was taken another step further and multi-mode ZnO resonators operating in the thickness-shear, hybrid, and longitudinal modes were introduced. These devices were characterized with respect to sample viscosity and conductivity and preliminary results show that, with further development, the multi-mode resonators provide significantly more information about a sample than their single-mode counterparts. An alternative to resonator-based platforms was also presented in the form of bulk acoustic delay lines. Initial conceptual and simulation results show that these devices provide a different perspective of typical sensing modalities by using properly designed input pulses, device tuning, and examining overall input and output signal spectra.

Advancing the field of nanotechnology to incorporate the unique properties observed at the nanoscale into functional devices has become a major scientific thrust of the 21st century. New fabrication tools and assembly techniques are required to design and manufacture devices based on one-dimensional nanostructures. Three techniques for manipulating nanomaterials post-synthesis have been developed. Two of them involve direct contact manipulation through the utilization of a physical probe. The third uses optically generated surface acoustic waves to reproducibly control and assemble one-dimensional nanostructures into desired locations. The nature of the third technique is non-contact and limits contamination and defects from being introduced into a device by manipulation. While the effective manipulation of individual nanostructures into device components is important for building functional nanosystems, commercialization is limited by this one-device-at-a-time process. A new approach to nanostructure synthesis was also developed to site-specifically nucleate and grow nanowires between two electrodes. Integrating synthesis directly with prefabricated device architectures leads to the possible mass production of NEMS, MEMS and CMOS systems based upon one-dimensional nanomaterials. The above processes have been pursued to utilize piezoelectric ZnO nanobelts for applications in high frequency electronic filtering as well as biological and chemical sensing. The high quality, single crystal, faceted nature of these materials make them ideal candidates for studying their properties through the designs of a bulk acoustic resonator. The first ever piezoelectric bulk acoustic resonator based on bottom-up synthesized belts will be demonstrated. Initial results are promising and new designs are implemented to scale the device to sub-micron dimensions. Multiple models will be developed to assist with design and testing. Some of models presented will help verify experimental results while others will demonstrate some of the problems plaguing further investigations.

Thesis (M.S.)--Joint Program in Oceanographic Engineering (Massachusetts Institute of Technology, Dept. of Ocean Engineering; and the Woods Hole Oceanographic Institution), 1997. / Includes bibliographical references (p. 65-66). / The Surface Suspended Acoustic Receiver (SSAR) is a free-drifting platform intended for use as a receiver in large scale acoustic tomography experiments. Early prototypes of the SSAR exhibited very poor signal-to-noise ratios in the frequency band of the hydrophones. This thesis details efforts to reduce the hydrophone noise level by combining the analysis of experimental data with the results from numerical models. Experiments were conducted to quantify both the frequency content and magnitude of noise generated on the SSAR. Through a program of sea trials and pond testing, two noise sources were identified. The dominant source of noise in the SSAR is velocity dependent flow noise that results from turbulent pressure fluctuations on the hydrophones. A second noise source results from the acceleration sensitivity of the hydrophones in conjunction with high frequency accelerations present in the hydrophone array cable. These high frequency accelerations also show a velocity dependence. The presence of the acceleration-induced noise leads to correlations between the signals from adjacent hydrophones, thus distorting the typical picture that flow noise should be uncorrelated along an array. The primary methods of eliminating the noise are encapsulating the hydrophone in a flow shield, eliminating the array cable, and slowing the system down by replacing the wave following surface buoy with a spar buoy. Using the experimental results, empirical relationships between hydrophone velocity and expected noise level are formed for both shielded and unshielded hydrophones. The numerical models developed as a part of this effort are then used to predict the velocities for a wide range of possible SSAR configurations. The models can also provide information, such as system tensions, that is useful in evaluating the longevity and survivability of SSARs. Modeled design fixes include subsurface component changes as well as comparing a wave following surface buoy to a spar buoy. / by Jason I. Gobat. / M.S.

No description available.

Surface acoustic wave (SAW) sensors offer a wireless, passive sensor solution for use in numerous environments where wired sensing can be expensive and infeasible. Single carrier frequency SAW sensor embodiments such as delay lines, and resonators have been used in single sensor environments where sensor identification is not a necessity. The orthogonal frequency coded (OFC) SAW sensor tag embodiment developed at UCF uses a spread spectrum approach that allows interrogation in a multi-sensor environment and provides simultaneous sensing and sensor identi- fication. The SAW device is encoded via proper design of multiple Bragg reflectors at differing frequencies. To enable accurate device design, a model to predict reflectivity over a wide range of electrode metallization ratios and metal thicknesses has been developed and implemented in a coupling of modes (COM) model. The high coupling coefficient, reflectivity and temperature coefficient of delay (TCD) of YZ LiNbO3 makes it an ideal substrate material for a temperature sensor, and the reflectivity model has been developed and verified for this substrate. A new concept of pseudo-orthogonal frequency coded (POFC) SAW sensor tags has been investigated, and with proper design, the POFC SAW reduces device insertion loss and fractional bandwidth compared to OFC. OFC and POFC sensor devices have been fabricated at 250 MHz and 915 MHz using fundamental operation, and 500 MHz and 1.6 GHz using second harmonic operation. Measured device results are shown and compared with the COM simulations using the iii enhanced reflectivity model. Additionally, the first OFC devices at 1.05 GHz were fabricated on 128o YX LiNbO3 to explore feasibility of the material for future use in OFC sensor applications. Devices at 915 MHz have been fabricated on YZ LiNbO3 and integrated with an antenna, and have then been used in a transceiver system built by Mnemonics, Inc. to wirelessly sense temperature. The first experimental wireless POFC SAW sensor device results and predictions will be presented.

In this study the description and development of intensity-based laser interferometric techniques for the detection and measurement of ultrasonic stress waves and their small displacement amplitudes is presented. The dynamic displacement sensitive interferometers described in the following chapters allow the quantitative point-by-point measurement of both in-plane and out-of-plane components of surface displacement motion. These uniquely developed interferometric sensors are: 1) an optical system design for the detection of the surface acoustic wave (Rayleigh wave). The technique is based on the Fourier analysis of coherent light and diffraction imaging properties of an illuminated grating; 2) the design and construction of a two-beam unequal-path laser interferometer for the measurement of out-of-plane surface displacement of ultrasonic waves; 3) extension of a flexible fiber optic probing device which is optically coupled to the test arm of the above two-beam interferometer. This permits scanning of the test surface which may be at some distance from the main optical system components; 4) the design and construction of a laser speckle interferometer for retro-reflective diffusing surfaces in which the in-plane displacements of the ultrasonic wave are interrogated. The inherent advantages of these newly designed optical configurations in terms of their greater simplicity, feasibility, and sensitivity over the conventional counterparts (classical/speckle laser interferometers) are explained. The function-response limitations of these interferometric sensors on lateral displacement resolution, on upper and lower-bound displacement sensitivity (dynamic range), on high-frequency bandwidth probing capability, on low-frequency environmentally associated noise disturbance, and on specularly reflective or diffusively retro-reflective specimen surface preparation are also mentioned. Finally, in a series of experimental observations, the application of a couple of these acoustic sensors in pulsed-excitation ultrasonic Specifically, the optically testing methods is cited. detected ultrasonic signals revealing the true nature of the various surface displacement modes of vibration are presented. / Ph. D.

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior / No presente trabalho, um algoritmo algébrico sequencial é utilizado para descrever a propagação de ondas acústicas ao longo de uma barra e utilizado na identificação de danos. Esse algoritmo é validado com base nos conficientes de sensibilidade dos ecos correspondentes aos diferentes cenários de danos apresentados. Na formulação do problema de identificação de dano, o campo de impedância generalizada, que minimiza o funcional definido como a distância entre o eco calculado e o eco experimental sintético é procurado. Os tempos de percurso da resposta, obtidos a partir de experimentos numéricos, são utilizados para identificar a posição, intensidade e forma do dano. Para simular dados corrompidos, diferentes níveis de ruído - variando de 30 a 0 dB - são introduzidos. O processo de identificação foi avaliado com os seguintes métodos de otimização: Otimização por Enxame de Partículas (PSO); Luus-Jaakola (LJ); Algoritmo de Colisão de Partículas (PCA); Algoritmos Genéticos (GA) e Recozimento Simulado (SA); e a hibridização desses métodos com o método determinístico de Levenberg-Marquardt. É mostrado que o processo de identificação de dano construído sobre a abordagem de propagação de ondas acústicas foi bem sucedido, mesmo para dados ruidosos altamente corrompidos. Os resultados dos casos testes são apresentados e algumas observações sobre as vantagens dos métodos determinísticos e estocásticos e sua combinação também são relatados. / In the present work, a sequential algorithm is used for describing the acoustic wave propagation along a bar and applied for damage identification purposes. The algorithm is validated based on the sensitivity coefficients of the corresponding echoes to the adressed damage scenarios. In the formulation of the damage identification problem, the generalized impedance field, that minimizes the functional defined as the distance between the calculated echo and the synthetic experimental one is sought. Time history responses, obtained from pulse-echo experiments, are used to identify damage position, severity and shape. In oder to account for noise corrupted data, different levels of signal to noise ratio - varying from 30 to 0 dB - are introduced. In the identification procedure the following optimization methods were applied: Particle Swarm Optimization (PSO); Luus-Jaakola (LJ); Particle Collision Algorithm (PCA); Genetic Algorithms (GA); and Simmulated Annealing (SA): and the hybridization of these methods with the deterministic Levenberg-Marquardt method. It is shown that the damage identification procedure built on the acoustic wave propagation approach was successful, even for highly corrupted noisy data. Test case results are presented and a few comments on the advantages of deterministic and stochastic methods and their combination are also reported.