<p>Microengineering has developed a broad range of production techniques to reduce size, increase throughput, and reduce cost of electrical and mechanical devices. The miniaturisation has also entailed entirely new opportunities.</p><p>In this work, a piezoresistive silicon sensor measuring mechanical deformation has been designed and fabricated with the help of microengineering. Due to the large variety of used processes, this device can serve as a survey of techniques in this field. Four basic process categories are recognised: additive, subtractive, modifying, and joining methods.</p><p>The last category, joining methods, has previously been the least investigated, especially when it comes to compatibility with the other categories. The adaptability of wet chemical etching to established silicon wafer bonding technique has been investigated. Further, phenomena related to oxygen plasma pre-treatment for direct bonding has been investigated by blister bond adhesion tests, X-ray photoelectron spectroscopy, and atomic force microscopy.</p><p>Wafer bonding has been adapted to monocrystalline quartz. For wet chemical pre-treatment, characteristics specific for quartz raise obstacles. Problems with limited allowable annealing temperature, low permeability of water released in the bond at annealing, and electrostatic bonding of particles to the quartz surface, have been studied and overcome. The influence of internal bond interfaces on resonators has been investigated.</p><p>Chemical polishing of quartz by ammonium bifluoride has been experimentally investigated at high temperatures and concentrations. Chemometrical methods were used to search for optimum conditions giving the lowest surface roughness. These extreme conditions showed no extra advantages.</p><p>Adhesion quantification methods for wafer bonding have been comprehensively reviewed, and augmentations have been suggested. The improved techniques’ usefulness for three areas of use has been forecasted: general understanding, bonding scheme optimisation, and quality control. It was shown that the quality of measurements of all commonly used methods could be dramatically improved by small means.</p>

Microengineering has developed a broad range of production techniques to reduce size, increase throughput, and reduce cost of electrical and mechanical devices. The miniaturisation has also entailed entirely new opportunities. In this work, a piezoresistive silicon sensor measuring mechanical deformation has been designed and fabricated with the help of microengineering. Due to the large variety of used processes, this device can serve as a survey of techniques in this field. Four basic process categories are recognised: additive, subtractive, modifying, and joining methods. The last category, joining methods, has previously been the least investigated, especially when it comes to compatibility with the other categories. The adaptability of wet chemical etching to established silicon wafer bonding technique has been investigated. Further, phenomena related to oxygen plasma pre-treatment for direct bonding has been investigated by blister bond adhesion tests, X-ray photoelectron spectroscopy, and atomic force microscopy. Wafer bonding has been adapted to monocrystalline quartz. For wet chemical pre-treatment, characteristics specific for quartz raise obstacles. Problems with limited allowable annealing temperature, low permeability of water released in the bond at annealing, and electrostatic bonding of particles to the quartz surface, have been studied and overcome. The influence of internal bond interfaces on resonators has been investigated. Chemical polishing of quartz by ammonium bifluoride has been experimentally investigated at high temperatures and concentrations. Chemometrical methods were used to search for optimum conditions giving the lowest surface roughness. These extreme conditions showed no extra advantages. Adhesion quantification methods for wafer bonding have been comprehensively reviewed, and augmentations have been suggested. The improved techniques’ usefulness for three areas of use has been forecasted: general understanding, bonding scheme optimisation, and quality control. It was shown that the quality of measurements of all commonly used methods could be dramatically improved by small means.

<p>Bonding techniques intended for assembling space microsystems are studied in this work. One of the largest problems in bonding pre-processed semiconductor wafers are the severe process restrictions imposed by material compatibility issues. Plasma processes have shown to be good for sensitive materials integration why the influence of different plasma parameters on the bondability of wafers is particularly studied. Conventional wet chemical and field-assisted methods are also examined. The resulting bond quality is assessed in terms of mechanical strength, homogeneity, and yield.</p><p>The effect of spaceflight environment on the reliability of wafer bonds is also investigated. Both high and low temperature annealed bonds are found to be very robust. Effects observed are that low temperature bonds are reinforced by thermal cycling in vacuum and that high temperature bonds degrade slightly by low dose γ irradiation.</p><p>Adhesion quantification is important for all bonding. Development of accurate quantification methods is considered necessary since most methods at hand are limited. This work includes the development of the blister test method. Former test structures are improved to be more practical to work with and to yield low experimental scatter. A physical stress model for the improved structure is suggested with which successful predictions of fracture for different test specimen configurations are made. The blister test method is used throughout this work to assess the strength of wafer bonds. The physics background and modelling of other common test methods are also thoroughly analysed. The methods’ practical capabilities and limitations are commented; origin and mitigation of measurement errors are discussed. It is shown that all methods can be significantly improved by small means.</p><p>Weibull statistics is introduced as a tool to characterise wafer bonds. This method is suitable to use in brittle materials design as the inherent variability in strength can be properly accounted for.</p>

Bonding techniques intended for assembling space microsystems are studied in this work. One of the largest problems in bonding pre-processed semiconductor wafers are the severe process restrictions imposed by material compatibility issues. Plasma processes have shown to be good for sensitive materials integration why the influence of different plasma parameters on the bondability of wafers is particularly studied. Conventional wet chemical and field-assisted methods are also examined. The resulting bond quality is assessed in terms of mechanical strength, homogeneity, and yield. The effect of spaceflight environment on the reliability of wafer bonds is also investigated. Both high and low temperature annealed bonds are found to be very robust. Effects observed are that low temperature bonds are reinforced by thermal cycling in vacuum and that high temperature bonds degrade slightly by low dose γ irradiation. Adhesion quantification is important for all bonding. Development of accurate quantification methods is considered necessary since most methods at hand are limited. This work includes the development of the blister test method. Former test structures are improved to be more practical to work with and to yield low experimental scatter. A physical stress model for the improved structure is suggested with which successful predictions of fracture for different test specimen configurations are made. The blister test method is used throughout this work to assess the strength of wafer bonds. The physics background and modelling of other common test methods are also thoroughly analysed. The methods’ practical capabilities and limitations are commented; origin and mitigation of measurement errors are discussed. It is shown that all methods can be significantly improved by small means. Weibull statistics is introduced as a tool to characterise wafer bonds. This method is suitable to use in brittle materials design as the inherent variability in strength can be properly accounted for.