No description available.

No description available.

No description available.

In this thesis, the tonal noise produced by flow over perforated plates at oblique angles of incidence is studied experimentally. A two-dimensional model of a perforated plate is used, where the circular holes of a typical perforated plate are replaced by a series of long rectangular Aluminum slats with an adjustable gap width between them. The slats are 3.175 mm thick and the gap width between them is set to 3.175 mm, 6.35 mm, and 12.7 mm. This simplified model is mounted at the exit of an open-loop wind tunnel and tested at angles of incidence of 0° to 40° and flow velocities of 0 to 30 m/s. An angle of 0° is defined as flow parallel to the plate. The acoustic response is studied using microphone measurements, and flow visualization is done using particle image velocimetry. The effect of the angle of incidence, flow velocity, gap width, and streamwise position are investigated. The flow visualization reveals that tonal noise is produced by the periodic shedding and impingement of vortices at the trailing edge of the gaps. Vortices form in the unstable free shear layer originating at the leading edge of the gap and impinge on the downstream side of the gap. At the downstream corner, these vortices separate into vortex pairs, consisting of one positively rotating and one negatively rotating vortex. These vortices are shed periodically, leading to the production of tonal noise at the shedding frequency. The effect of the angle of incidence is investigated by changing the angle of the plate with respect to the flow. For a given gap width, tones are produced only for a specific range of angles. Depending on the plate geometry, this range of angles is typically around 5° to 30°. Within this range of angles, the free shear layer impinges on the downstream side of the gap. For angles which are too small or too large, the free shear layer misses this downstream side and tones are not produced. For a larger gap width, tones are produced at smaller angles of incidence. Similarly, for a given plate geometry, there is a preferred range of flow velocities at which tonal noise is produced. The velocity at which the free shear layer is the most unstable at the tone frequency produces the strongest vortices and the loudest tones. The optimal velocity is lower for larger gap widths. Finally, it is found that the magnitude of the produced tones increases in the streamwise direction over repeated gaps along the length of the plate. This is due to the local flow conditions changing in the streamwise direction, only reaching the optimal conditions after a certain length of the plate. / Thesis / Master of Applied Science (MASc)

The aerodynamic behavior of wind tunnels with porous, flexible walls formed from tensioned Kevlar has been characterized and new measurement techniques in such wind tunnels explored. The objective is to bring the aerodynamic capabilities of so-called Kevlar-wall test sections in-line with those of traditional solid-wall test sections. The primary facility used for this purpose is the 1.85-m by 1.85-m Stability Wind Tunnel at Virginia Tech, and supporting data is provided by the 2-m by 2-m Low Speed Wind Tunnel at the Japanese Aerospace Exploration Agency, both of which employ Kevlar-wall test sections that can be replaced by solid-wall test sections. The behavior of Kevlar fabric, both aerodynamically and mechanically, is first investigated to provide a foundation for calculations involving wall interference correction and determination of the boundary conditions at the Kevlar wall. Building upon previous advancements in wall interference corrections for Kevlar-wall test sections, panel method codes are then employed to simulate the wind tunnel flow in the presence of porous, flexible Kevlar walls. An existing two-dimensional panel method is refined by examining the dependency of correction performance on key test section modeling assumptions, and a novel three-dimensional method is presented. Validation of the interference corrections, and thus validation of the Kevlar-wall aerodynamic performance, is accomplished by comparing aerodynamic coefficients between back-to-back tests of models carried out in the solid- and Kevlar-wall test sections. Analysis of the test results identified the existence of three new mechanisms by which Kevlar walls cause wall-interference. Additionally, novel measurements of the boundary conditions are made during the Kevlar-wall tests to characterize the flow at the boundary. Specifically, digital image correlation is used to measure the global deformation of the Kevlar walls under wind loading. Such data, when used in conjunction with knowledge of the pre-tension in the Kevlar wall and the material properties of the Kevlar, yields the pressure loading experienced by the wall. The pressure loading problem constitutes an inverse problem, and significant effort is made towards overcoming the ill-posedness of the problem to yield accurate wall pressure distributions, as well as lift measurements from the walls. Taken as a whole, this document offers a comprehensive view of the aerodynamic performance of Kevlar-wall test sections. / Ph. D.

Trailing edge noise control is an important problem associated mainly with wind turbines. As turbulence in the air flows over a wind turbine blade, it impacts the trailing edge and scatters, producing noise. Traditional methods of noise control involve modifying the physical trailing edge, or the scattering efficiency. Recently, inspired by the downy covering of owl feathers, researchers developed treatments that can be applied to the trailing edge to significantly reduce trailing edge noise. It was hypothesized that the noise reduction was due to manipulating the incoming turbulence, rather than the physical trailing edge itself, representing a new method of noise control. However, only acoustic measurements were reported, meaning the associated flow physics were still unknown. This thesis describes a comprehensive wall jet experiment to measure the flow effects near the bio-inspired treatments, termed “finlets” and “rails,” and relate those flow effects to the noise reduction. This was done using far-field microphones, a single hot-wire probe, and surface pressure fluctuation microphones. The far-field noise results showed that each treatment successfully reduced the noise, by up to 7 dB in some cases. The surface pressure measurements showed that the spanwise coherence was slightly reduced when the treatments were applied to the trailing edge. The velocity measurements clearly established the presence of a shear layer near the top of the treatments. As a whole, the dataset led to the shear-sheltering hypothesis: the bio-inspired treatments are effective based on reducing the spanwise pressure correlation and by sheltering the trailing edge from turbulent structures with the shear layer they create. / Master of Science / This thesis describes a project aimed at developing a technology inspired by the silent flight of owls, with the end goal of using this technology to reduce the noise generated by wind turbines. Specifically, the phenomenon known as "trailing edge noise" is the primary source of wind turbine noise, and is the noise source of interest here. It occurs when air turbulence (which can be thought of as unsteady air fluctuations) crashes into the rear (trailing) edge of wind turbine blades, scattering and producing noise. Typically, methods of reducing this noise source involve changing the shape of the trailing edge; this may not always be practical for existing wind turbines. Recently, inspired by the downy covering of owl feathers, researchers developed treatments that can be applied directly to the trailing edge, significantly reducing trailing edge noise. This bio-inspired concept was verified with numerous acoustic measurements. Based on those measurements, researchers hypothesized that the noise reduction was achieved by manipulating the incoming turbulence before it scattered off the trailing edge, rather than by changing the existing wind turbine blade, representing a new method of trailing edge noise control. However, as only acoustic measurements (not flow measurements) were reported, the changes in turbulence could not be examined. With the above motivation in mind, this thesis describes a comprehensive wind tunnel experiment to measure the changes in the aerodynamics and turbulence near the bio-inspired treatments, and relate those changes to the reduction in trailing edge noise. This was done using a hot-wire probe to measure the aerodynamics, as well as microphones to measure the radiated noise and surface pressure fluctuations. As a whole, the experimental results led to the shear-sheltering hypothesis: the bio-inspired treatments are effective based on the creation of a shear layer (a thin region between areas with different air speeds) which shelters the trailing edge from some turbulence, as well as by de-correlating surface pressure fluctuations along the trailing edge.

Simultaneous two-point three-component four-sensor hot-wire velocity measurements taken in three flows of aeroacoustic interest are here analyzed. The analyses provide information on the turbulence structure of the flows as it would be encountered by hypothetical noise producing blades passing through the flows. Two-point measurements taken in the first flow, a lifting wake from a rectangular NACA 0012 half wing, are used to calculate space-time correlation functions and 'pointwise' wave number frequency spectra. Two upwash spectra, calculated for locations in the region of the wake that is roughly homogenous in the spanwise direction, are direct estimates of the full wave number frequency spectra at their locations. As such, they are used to perform aeroacoustic calculations, and the results are compared to results achieved using the von Kármán isotropic spectrum. Amiet's approximation, where the wave number frequency spectra can be represented by the correlation length scales is found to hold reasonably well for the measured spectra. The two-point measurements in the second flow, a vortex/blade-tip interaction, are analyzed to provide information useful to researchers of blade-wake interaction noise produced by helicopter rotors. Space-time correlation functions and wave number frequency spectra are calculated for five cuts through the region of interaction. The correlation functions provide information concerning the turbulence length scales found in the interaction region. The spectra are compared to the von Kármán isotropic spectrum and found to be greatly different. However, the spectra do bear some resemblance to spectra calculated in the spanwise homogenous region of the lifting wake. The two-point measurements taken in the third flow, the wake from a fan cascade, are analyzed to provide information of use to modelers of broadband noise produced through rotor wake/stator interactions. In particular, space-time correlation functions are calculated for a grid of two-point measurements, which allows the estimation of the turbulence structure as seen by a passing stator blade. Space-time correlation functions and wave number frequency spectra are calculated for various stator configurations. The implications of engine operating speed and stator configuration for broadband noise production are discussed. <i> [Vita removed March 2, 2012. GMc]</i> / Master of Science

Sound generation and propagation in circular ducts for frequencies beyond the cut-on frequencies of several higher order acoustic modes is investigated. To achieve this, experimental and numerical set-ups are designed and used to research aeroacoustic interactions between in-duct components and to conceive noise mitigation strategies. Describing in-duct sound for frequencies with a moderate number of propagating modes is important, for example, for improving the noise emission from mid-size ventilation systems. Challenges that are largely unacknowledged in the literature involve efficient test rig design, quantification of limits in the methods, numerical modelling, and development of effective noise mitigation strategies for higher order modes. In this thesis, in-duct sound is mapped on a set of propagating pressure eigenmodes to describe aeroacoustic components as multi-ports with sound scattering (passive properties) and a source strength (active properties). The presented analysis includes genetic algorithms and Monte Carlo Methods for test rig enhancement and evaluation, multi-port network predictions to identify model limitations, and scale resolving (IDDES) and Linearized Navier Stokes computations for numerical multi-port eduction and the silencer design. It is first shown that test rig optimization improves the quality of multi-port data significantly. Subsequently, measurements on orifice plates are used to test the network prediction model. The model works with high accuracy for two components that are sufficiently separated. For small separations, strong coupling effects are observed for the source strength but not for the scattering of sound. The measurements are used for numerical validation, which gives reliable results for coupled and uncoupled systems. The total acoustic power of tandem orifices is predicted with less than 2 dB deviation and the passive properties for most frequencies with less than 5 % difference from the measurement. The numerical (FEM) models are also used to design a completely integrated silencer for spinning modes that is based on micro-perforated plates and gives broadband attenuation of 3-6 dB per duct diameter silencer length. The multi-port method is a powerful tool when describing aerodynamically decoupled in-duct components in the low- to mid-frequency range. Due to a robust passive network prediction, multi-port methods are particular interesting for the design of silencer stages. Furthermore, the demonstrated applicability to numerical data opens novel application areas. / <p>QC 20170522</p> / IdealVent

Cette thèse vise à étudier le couplage entre méthodes de Galerkine discontinue (DG) et méthodes de différences finies (DF) en maillages hybrides non structuré / cartésien, en vue d'applications en aéroacoustique numérique. L'idée d'une telle approche consiste à pouvoir tirer profit localement des avantages respectifs de ces méthodes, soit, en d'autres termes, à pouvoir prendre en compte la présence de géométries complexes par une méthode DG en maillage non structuré, et les zones qui en sont suffisamment éloignées par une méthode DF en maillage cartésien, moins coûteuse. Plus précisément, il s'agit de concevoir un algorithme d'hybridation de ces deux types de schémas pour l'approximation des équations d'Euler linéarisées, puis d'évaluer avec attention le comportement numérique des solutions qui en sont issues. De par le fait qu'aucun résultat théorique ne semble actuellement atteignable dans un cas général, cette étude est principalement fondée sur une démarche d'expérimentation numérique. Par ailleurs, l'intérêt d'une telle hybridation est illustré par son application à un calcul de propagation acoustique dans un cas réaliste / This thesis aims at studying coupling techniques between Discontinuous Galerkin (DG) and finite difference (FD) schemes in a non-structured / Cartesian hybrid-mesh context,in the framework of Aeroacoustics computations. The idea behind such an approach is the possibility to locally take advantage of the qualities of each method. In other words, the goal is to be able to deal with complex geometries using a DG scheme on a non-structured mesh in their neighborhood, while solving the rest of the domain using a FD scheme on a cartesian grid, in order to alleviate the needs in computational resources. More precisely, this work aims at designing an hybridization algorithm between these two types of numerical schemes, in the framework of the approximation of the solutions of the Linearized Euler Equations. Then, the numerical behaviour of hybrid solutions is cautiously evaluated. Due to the fact that no theoretical result seems achievable at the present time, this study is mainly based on numerical experiments. What's more, the interest of such an hybridization is illustrated by its application to an acoustic propagation computation in a realistic case

Le développement de systèmes de propulsion alternatifs aux turboréacteurs actuels constitue un axe de recherche important dans le contexte aéronautique. L’open-rotor, moteur à hélices contrarotatives, constitue une piste sérieuse car il permet à la fois de réduire fortement la consommation de carburant et les émissions de gaz. Toutefois, les émissions sonores restent un défi pour ce type d’architecture, notamment du fait de l’absence de carénage. La compréhension des sources acoustiques et leur prévision est nécessaire afin de pouvoir, par la suite, réduire le bruit de ces moteurs. Les écoulements d’un doublet d’hélices contrarotatives sont complexes, en particulier pour l’hélice aval qui constitue l’axe d’étude de la thèse. Le travail présenté est dédié à une étude numérique, expérimentale et analytique et intervient dans le cadre de la chaire industrielle ADOPSYS entre Safran Aircraft Engines et l’Ecole Centrale de Lyon. L’objectif de ce travail est double. Il s’agit d’une part de réaliser une campagne expérimentale afin d’observer et de mieux comprendre le comportement de l’écoulement et de l’acoustique d’une pale en flèche, notamment en réponse à la présence d’un tourbillon de bord d’attaque. Un second objectif de la thèse était de constituer une base de données afin de comparer les prévisions obtenues avec un modèle analytique. Une méthode de calcul semi-analytique de la réponse aéroacoustique d’une pale aval en réponse à une excitation provenant de l’amont et prenant en compte les effets de charge et de géométrie a été développée. Une étude numérique d’un doublet d’hélices contrarotatives a servi de base à la définition de la géométrie de pale utilisée pendant l’étude. Celle-ci a été définie de façon à observer un tourbillon de bord d’attaque pour certains angles d’incidence. La maquette a ensuite été placée dans une soufflerie anéchoïque de l’Ecole Centrale de Lyon afin de réaliser une étude paramétrique. Des visualisations par enduit visqueux et des mesures de pression pariétale permettent de rendre compte de la présence du tourbillon de bord d’attaque à certains angles d’incidence. L’étude des spectres en champ lointain permet de distinguer un comportement en trois régimes, associés aux trois comportements du tourbillon de bord d’attaque. Des mesures de localisation de sources permettent de corroborer ces observations. Des prévisions analytiques du bruit émis par la pale et se basant sur le modèle d’Amiet ont également été réalisées. Dans un premier temps, les effets de la flèche sont pris en compte dans le modèle et celui-ci est alors appliqué à la pale de l’étude. Une meilleure adéquation des résultats est alors trouvée quand les effets de flèche sont pris en compte, en particulier dans les directions perpendiculaires à la pale. Le modèle est ensuite étendu afin de prendre en compte les effets de la jonction en pied de pale. Cette partie est exploratoire et le développement reste à approfondir. Un complément à l’expérience a consisté en l’étude de l’impact de sillages défilants sur la pale. Un système de barreaux rotatifs permet de générer des sillages périodiques représentatifs d’une interaction de sillages rotor-rotor. Les mesures réalisées montrent le comportement quasi-stationnaire du tourbillon. / The development of alternative propeller systems to turbojets is a main issue for research in the current context of aeronautical transport. Counter rotating open rotors are a candidate solution because they allow reduction of fuel consumption and gas emission. However, noise emissions are still a challenge for these types of configuration, in particular because they cannot benefit from the nacelle and the liners currently used in turbojet. The understanding of acoustic sources and their prediction is necessary in order to be able to reduce noise emission in the near future. Flows in an open-rotor are complex, in particular for the downstream propeller which is the subject of this approach.This work based on a numerical, experimental and analytical study and takes part in the ADOPSYS chair between Safran Aircraft Engines and l’Ecole Centrale de Lyon. This PhD has two main goals. The first one is to complete an experimental study in order to elucidate the behavior of the flow on a swept airfoil and the resulting acoustics, with a possibly developing leading-edge vortex. The measurements will be a data base for further comparison with analytical prediction. The second objective of the PhD consists in developing a semi-analytical modeling of the noise emitted by an airfoil in response to an incoming perturbation, taking into account the loading and geometry effects. A numerical study of a full counter-rotating system was used as a basis for designing the investigated airfoil. The latter was designed so that a leading-edge vortex could be formed on the surface for some angles of attack. The mock-up was then tested in an anechoic wind tunnel of Ecole Centrale de Lyon for various sets of parameters. Flow visualization and wall-pressure measurements indicated the presence of the leading-edge vortex for some angles of attack. The far-field measurements indicated three acoustic regimes, which can be associated with three behaviors of the leading-edge vortex. Source localization measurements corroborate these observations. Analytical predictions of the noise emitted by the airfoil and based on Amiet’s model were also performed. Firstly, the sweep angle is taken into account in the model. Secondly it is applied to the studied airfoil. A better match of the results is found when the sweep is considered, in particular in the perpendicular directions. The model in then extended in order to include the wall-junction. This part is exploratory and should be further developed. Finally, a complementary experimental investigation of the impingement of periodic wakes on the airfoil has been performed, using a system made of rotating bars, mimics true wake interactions. The measurements suggest that the leading-edge vortex has a quasi-steady behavior.