Manufacturing of aero engine components requires attention to residual stress and final shape of the product in order to meet high quality product standards.This sets very high demands on involved manufacturing steps to meet design requirements. Simulation of manufacturing processes can therefore be animportant tool to contribute to quality assurance.The focus in this work is on simulation of a manufacturing process chain comprising of sheet metal forming, welding and a stress relief heat treatment.Simulation of sheet metal forming can be used to design a forming tool design that accounts for the material behaviour, e.g. spring back, and avoid problems such as wrinkling, thinning and cracking. Moreover, the simulation can also show how the material is stretched and work hardened. The residual stresses after forming may be of local character or global depending on the shape that is formed. However, the heat affected zone due to welding is located near the weld.The weld also causes large residual stresses with the major component along the weld. It is found that the magnitude of the residual stresses after welding is affected by remaining stresses from the previous sheet metal forming. The final stress relieve treatment will relax these residual stresses caused by e.g. forming and welding. However, this causes additional deformations.The main focus of this study is on how a manufacturing process step affects the subsequent step when manufacturing a component of the nickel-based super alloy 718. The chosen route and geometry is a simplified leading edge of an exhaust case guide vane. The simulations were validated versus experiments. The computed deformations were compared with measurements after each manufacturing step. The overall agreement between experiments and measurement was good. However, not sufficiently accurate considering the required tolerance of the component. It was found from simulations that the residual stresses after each process affects the subsequent step. After a complete manufacturing process chain which ends with a stress relief heat treatment the residual stresses were not negligible. VIII Special experiments were performed for studying the stress relief in order to understand how the stresses evolve through the heat treatment cycle during relaxation. It was found that the stresses were reduced already during the beginning of the heating up sequence due to decreasing Young´s modulus and yield stress with increasing temperature. Relaxation due to creep starts when a certain temperature was reached which gave a permanent stress relief.

No description available.

Electron beam melting (EBM), a metal additive manufacturing (AM) process, has received considerable industrial attention for near net shape manufacture of complex geometries with traditionally difficult-to-machine materials. This has fuelled considerable academic interest in investigating EBM of Alloy 718, a nickel ironbased superalloy possessing an exciting combination of good mechanical behaviour and cost effectiveness. EBM production of Alloy 718 is particularly promising for aerospace and other sectors which value rapid production of components with large scope for design flexibility. The EBM builds are characterized by presence of inevitable defects and, anisotropy within a build is also a concern. Consequently, as-built Alloy 718 has to be subjected to post-build thermal-treatments (post-treatments) to ensure that the parts eventually meet the critical service requirements. Not withstanding the above, limited knowledge is available about optimal post-treatments for EBM-built Alloy 718. Therefore, the main focus of the work presented in this thesis was to systematically investigate the response of EBM-built material to post-treatments, which include hotisostatic pressing (HIPing), solution treatment (ST), and aging. HIPing of EBM-built Alloy 718 led to more than an order of magnitude reduction in defect content, which was reduced from as high as 17% to &lt; 0.2% in samples built with intentionally introduced porosity to investigate limits of defect closure achievable through HIPing. In addition, HIPing also caused complete dissolution of δ and γ" phases present in the as-built condition, with the latter causing dropin hardness of the material. HIPing had no effect on the carbides and inclusions such as TiN, Al2O3 present in the built material. The evolution of microstructure during ST and aging was systematically investigated. Growth of potentially beneficial grain boundary δ phase precipitates was found to cease after a certain duration of ST, with samples subjected to prior-HIPing exhibiting lesser precipitation of the δ phase during ST. While the specimen hardness increased onaging, it was observed to plateau after a duration significantly shorted than the specified ASTM 'standard' aging cycle. Therefore, prima facie there are promising prospects for shortening the overall heat treatment duration. A combination of HIPing, ST, and aging treatments in a single uninterrupted cycle was also explored. Future work involving incorporation of a shortened heat treatment schedule in a combined cycle can have significant industrial implications. / <p>Articles submitted to journals and unpublished manuscripts are not included in this registration</p>

This research focused on a comprehensive microstructural and mechanical property characterisation study of the Ni-Fe-Cr alloys 718 and 945X. The aim of the project was to better understand the relationship between performance and microstructure of existing (Alloy 718) and newly developed (Alloy 945X) high strength nickel alloys focusing on downhole applications. The main difference between the two alloys is that alloy 945X has lower Nb content than alloy 718, which may minimise the tendency to form delta when combined with correct processing. Previous studies have related the hydrogen embrittlement in alloy 718 with the collection of hydrogen by delta phase. Microstructural characterisation of the new alloy 945X after long term isothermal exposure up to 120 hours in the temperature range 650◦C to 900◦C was conducted with scanning electron microscopy (SEM), to generate a time-temperature-transformation (TTT) diagram. The TTT diagram was used as a road map for designing two isothermal heat treatments of alloy 945X on tensile specimens. Then, the effect of hydrogen charging on the tensile properties and microstructure of the 'as-received' and these two variant heat treatments was investigated. Fractographic analysis showed that, in the presence of hydrogen, intergranular fracture occurred for all the heat treatments, regardless the presence of delta phase at grain boundaries. There was no simple correlation between the volume fraction of delta-phase and susceptibility to hydrogen assisted embrittlement. Rather, it was demonstrated that the morphology and distribution of delta-phase along grain boundaries plays a key role and the other precipitate phases also have an influence through their effect on the ease of strain localisation. This study also examined the hydrogen embrittlement sensitivity of nickel alloy 718 given four different heat treatments to obtain various microstructural states. Each heat treatment leads to differences in the precipitate morphologies of γ', γ'' and delta phases. Material characterisation and fractography of the examined heat treatments were performed using a high resolution FEG-SEM. Three specimens of each condition were pre- charged with hydrogen and tensile properties were compared with those of non-charged specimens. It was observed that hydrogen embrittlement was associated with intergranular and transgranular microcrack formation, leading to an intergranular brittle fracture. delta phase may assist the intergranular crack propagation, and this was shown to be particularly true when this phase is coarse enough to produce crack initia- tion, but this is not the only factor determining embrittlement. Other microstructural features play a role, as does the strength of the material. Finally, the evolution of delta-(Ni3Nb) phase in alloy 718 from the early stages of precipitation, with a particular focus on identifying the grain boundary characteristics that favour precipitation of grain boundary delta phase was investigated. Results showed that delta phase was firstly formed on Σ3 boundaries after 5 hours at the examined temperature (800◦C). Increasing ageing time at 800◦C was observed to lead to an increase in size and precipitation of phases γ'-γ''-delta, an increase in fraction of the special CSL boundaries and an evolution in the morphology of twins and the growth of grains.

Additive manufacturing (AM) is the name given to the technology of building 3D parts by adding layer-by-layer of materials, including metals, plastics, concrete, etc. Of the different types of AM techniques, electron beam melting (EBM), as a powder bed fusion technology, has been used in this study. EBM is used to build parts by melting metallic powders by using a highly intense electron beam as the energy source. Compared to a conventional process, EBM offers enhanced efficiency for the production of customized and specific parts in aerospace, space, and medical fields. In addition, the EBM process is used to produce complex parts for which other technologies would be either expensive or difficult to apply. This thesis has been divided into three sections, starting from a wider window and proceeding to a smaller one. The first section reveals how the position-related parameters (distance between samples, height from build plate, and sample location on build plate) can affect the microstructural characteristics. It has been found that the gap between the samples and the height from the build plate can have significant effects on the defect content and niobium-rich phase fraction. In the second section, through a deeper investigation, the behavior of Alloy 718 during the EBM process as a function of different geometry-related parameters is examined by building single tracks adjacent to each other (track-by-track) andsingle-wall samples (single tracks on top of each other). In this section, the main focus is to understand the effect of successive thermal cycling on microstructural evolution. In the final section, the correlations between the main machine-related parameters (scanning speed, beam current, and focus offset) and the geometrical (melt pool width, track height, re-melted depth, and contact angle) and microstructural (grain structure, niobium-rich phase fraction, and primary dendrite arm spacing) characteristics of a single track of Alloy 718 have been investigated. It has been found that the most influential machine-related parameters are scanning speed and beam current, which have significant effects on the geometry and the microstructure of the single-melted tracks.

The aerospace industry is constantly striving to becoming more economical and environmentally friendly. One of many efforts to achieve this is the Lightcam project which in this case is evaluating the use of additive manufacturing in the form of electron beam melting in conjunction with the nickel-based superalloy, Alloy 718. This combination is not fully explored and examined. For this purpose, a demonstrator vane was produced and it was subsequently evaluated in this thesis. The evaluation was performed in as-built condition and was divided in non-destructive testing, evaluation of these methods and metallographic review to confirm the results, and potentially revealing more properties. The non-destructive testing was performed using conventional radiography and computed tomography. Both methods struggled to deliver complete and reliable results, for varying reasons. Radiography could deliver results of the whole vane, but these were impossible to evaluate due to the rough surface created by the electron beam melting process. The computed tomography on the other hand was not affected by the rough surface and produced usable, though not complete, results of the vane. The reason for the computed tomography’s inability to deliver complete results was the material, varying thickness and complex geometry of the vane. As a complement and to verify the results from the non-destructive testing, a metallographic examination was conducted. These tests were conducted with the aim of answering the following three questions:  What non-destructive testing methods are suitable to evaluate Alloy 718 components manufactured with electron beam melting? - Neither radiography nor computed tomography are suitable as a sole evaluation method, for various reasons. All surface dependent methods were deemed unsuitable without testing due to the rough surface. What types of defects and in what quantity can they be found in the produced vane? - Defects found are: Porosity and lack of fusion, both found as internal and partially external and in varying sizes. Where are the defects located? - Pores are mainly found in the center of sections modeled to a 3mm thickness. Lack of fusion was found between build layers in all thicknesses. Apart from these results, hardness was found to vary depending on build height, increasing from the bottom towards the top. Microstructure was also found to vary with the build height, but always consisting of either equiaxed or columnar grains. / Lightcam

No description available.