Polyimides are frequently used as insulating layers in the microelectronics industry. These polymers are tough, have high thermal stability, and have favorable dielectric properties; consequently, polyimides are excellent materials for insulating layers in microelectronic devices. In this research, self-assembled monolayers are investigated for use as an adhesion promoter for metal substrates, and for corrosion protectors of the metal surface. Gold substrates modified by adsorption of 3- and 4-aminothiophenol monolayers, 3- and (4-mercaptophenyl) phthalimide (MPP) monolayers, and by reaction of the 3- and 4-aminothiophenol monolayers with the phthalic anhydride were studied using reflection absorption infrared spectroscopy, contact angle measurement, ellipsometry, and electrochemical measurements. Reactions on the monolayers are used to model the attachment of an insulating polyimide to the substrate. The covalent attachment of the anhydride is confirmed, and the efficiency of the reaction of the aminothiolphenol monolayers is investigated. The reactivity of the aminothiolphenol monolayers is found to depend on the position of the amino-group around the phenyl ring. Impedance spectroscopy is used to investigate the ionic insulating properties of these systems. The 4-mercaptophthalimide monolayer is found to have the highest monolayer resistance to ion transport. This result suggests that it forms the most densely packed monolayer. The monolayer resistance of the surfaces prepared by adsorption of the aminothiolphenol isomers followed by reaction with phthalic anhydride is much lower than the corresponding deposited mercaptophthalimide monolayers. These results suggest that the reaction efficiency is low. Impedance spectroscopy and polarization measurements suggests a higher protection efficiency for 3-mercaptophenylphthalimide. These results will be discussed in the context of the ability of the isomeric mercaptophthalimide monolayers to serve as protectors against substrate corrosion. / Ph. D.

Constructing a detailed understanding of the heterogeneous oxidation of atmospheric organic aerosols, both from a mechanistic and kinetic perspective, will enable researchers to predict the fate and lifetime of atmospheric gases and the particles with which they interact. In an effort to develop a more complete understanding of the interfacial reactions of ozone with vinyl-containing organic thin films, self-assembled monolayers that contain vinyl groups positioned precisely at the gas/surface interface were synthesized as model systems for atmospheric organic aerosols. To isolate the reactions of background gases with ozone or surface products, an ultrahigh vacuum surface analysis instrument was designed and constructed to explore the reactions of ozone with the atmospheric model systems. The surface reactions can be monitored in real-time with reflection absorption infrared spectroscopy (RAIRS) and mass spectrometry. The chemical identity of adsorbates on a surface can also be determined before or after a reaction with X-ray photoelectron spectroscopy (XPS). Disordering of the monolayers concurrent with the disappearance of the vinyl group was observed with RAIRS. New bands within the RAIR spectra were observed and assigned to carbonyl or carboxylic acids bound to the surface. Little oxidation of the sulfur head groups and no significant loss of carbon during the reaction was observed with XPS. A mechanism is proposed that includes the cross linking of the hydrocarbon chains within the monolayer, which impedes further oxidation of the sulfur head group and limits desorption of the chains. By RAIRS, the kinetics of the oxidation of the vinyl groups were tracked and an observed rate constant was determined by monitoring the changes in IR absorbance of the C=C bond. With the aid of the rate constant, an initial reaction probability for the collisions of ozone with vinyl groups positioned precisely at an interface was determined. The reaction probability is approximately three orders of magnitude greater than the reaction probability for an analogous gas-phase reaction, which demonstrates that the gas/surface interface plays an important role in this reaction. The results presented in this thesis should help develop a more detailed understanding of the interfacial reactions of pure ozone at surfaces. / Ph. D.

This dissertation describes the impact of defects on monolayer properties for self-assembled monolayers (SAMs) created by interfacial patterning methods. When forming a two-dimensional interfacial pattern with n-alkanethiols on gold, the desired electrochemical properties are those of a homogeneous, solution adsorbed monolayer. However, even well-ordered SAMs contain a small degree of defects, especially at domain boundaries where two nucleating domains converge. Patterning a surface creates user-defined domain boundaries within the monolayer, potentially having a significant impact on the properties of the interface. This dissertation investigates the effect that user-created domain boundaries have on the properties of a monolayer, as studied by electrochemical impedance spectroscopy. Two patterning methods are investigated for creating user-defined domain boundaries: the soft lithography method of contact printing and site-selective reductive desorption. The electrochemical properties of homogeneous contact printed monolayers are measured and compared to those of monolayers prepared by solution adsorption. The contact printed monolayers are found to have dramatically different impedance behavior from the solution prepared monolayers, consistent with the contact printed monolayers having greater defect density. In addition, these studies show that the overall defect density depends on the concentration of the solutions used for contact printing. In this work, simple patterns are created by contact printing a pattern onto the substrate and then backfilling the remaining gold substrate by solution adsorption. Backfilling with the same alkanethiol used to create the pattern generates a homogeneous monolayer; however, it is found that the contact printed/backfilled monolayer has an impedance intermediate between the homogeneous contact printed and the homogeneous solution adsorbed monolayer. This result suggests that the backfilling process also saturates the pinhole defects associated with the contact printed areas. In addition to exploring defects that arise from contact printing, simple patterns with user-defined defects, created by site-selective reductive desorption (SSRD), were also investigated. Following the backfill step, the impedance behavior of the SSRD produced patterns was similar to that of the impedance of the initial pattern before backfilling. This important result implies that the domain boundaries play the most important role in defining the overall impedance of the patterned interface. / Ph. D.

Hydrogen sulfide (H2S) is a gasotransmitter that is produced endogenously and freely permeates cell membranes. It plays important roles in many physiological pathways, and by regulating these pathways, it provides many therapeutic effects. For example, H2S dilates vascular vessels, promotes angiogenesis, and protects cells from oxidative stress. Due to its therapeutic effects, H2S has been used as a potential treatment for diseases like diabetes, ischemia-reperfusion injuries, lung diseases, ulcers and edemas, among others. To apply H2S for therapeutic applications, two challenges need to be addressed. The first challenge is the H2S donor, which not only provides H2S but must be stable enough to avoid side effects caused by overdose; and the second challenge is the delivery strategies, which transport the H2S to the target sites. A series of S-aroylthiooximes (SATOs), an H2S releasing compound, were synthesized and conjugated to peptide sequences to form H2S-releasing aromatic peptide amphiphile (APA) hydrogels. APAs formed nanofibers, which were stabilized by beta-sheets and aromatic stacking. The self-assembled structures were affected by the substituents on the aromatic rings of SATOs, leading to the formation of twisted nanofibers. After the addition of cysteine, H2S was released from the APAs with half-lives ranging from 13 min to 31 min. The electron-donating groups slowed down the H2S release rate, while the electron-withdrawing groups accelerated the release rate. Therefore, the release rates of H2S were controlled by electronic effects. When self-assembled structures were formed, the H2S release rate was slowed down even more, due to the difficulties in cysteine diffusion into the core of the structures. Antimicrobial effects were also discovered using the H2S releasing APA hydrogels. The H2S-releasing dipeptides S-FE and S-YE formed self-assembled twisted nanoribbons and nanotubes, respectively. The non H2S-releasing control oxime dipeptides C-FE and C-YE were also synthesized. The C-FE formed nanoribbons while the C-YE only showed non-specific aggregates. S-FE and S-YE released H2S with peaking times of about 41 and 39 min. Both the self-assembled structures and the release rates were affected by their packing differences. In vitro and ex vivo experiments with Staphylococcus aureus (Xen29), a commonly found bacterium on burn wounds, showed significant antimicrobial effects. APAs S-FE and C-FE eliminated Xen29 and inhibited the biofilm formation, while S-FE always showed better effects than C-FE. These antimicrobial H2S-releasing APA hydrogels provide a new approach to treat burn wound infections, and provide healing benefits due to the therapeutic effects of H2S. / Doctor of Philosophy / Hydrogen sulfide (H₂S) is a signaling gas that produced in our body. It regulates physiological pathways, and can be a potential treatment for diseases like diabetes, ischemia-reperfusion injuries, lung diseases, ulcers and edemas, among others. However, two issues need to be addressed before applying H₂S for disease treatments. The first issue is to choose an H₂S donor, which is stable enough to avoid side effects caused by overdose. The second issue is the delivery methods, which transport the H₂S to target sites. A series of S-aroylthiooximes (SATOs), an H₂S releasing compound, were synthesized and attached to peptide sequences to form H₂S-releasing self-assembled aromatic peptide amphiphile (APA) hydrogels. The APA hydrogels were found to be affected by the substituents on the SATO structures. For example, the H₂S released from APAs had halflives ranged from 13 min to 31 min, which were controlled by the substituents. When hydrogels were formed, the H₂S release was slowed down even more, due to the difficulties in cysteine diffusion into the SATO structures. The antimicrobial effects were also discovered using the H₂S releasing APA hydrogels. Two H₂S-releasing APA hydrogels, S-FE and S-YE, were formed. At the same time, two non H₂S-releasing oxime dipeptides, C-FE and C-YE, were also synthesized as controls. The H₂S-releasing peptides, S-FE and S-YE, released H₂S with peaking times of about 41 and 39 min, while no H₂S was released from C-FE and C-YE. The self-assembled structures and the release rates were affected by their structural differences. In vitro and ex vivo experiments with Staphylococcus aureus (Xen29), a commonly found bacterium on burn wound, showed significant antimicrobial effects. Both H₂S-releasing S-FE and non H₂S-releasing C-FE eliminated Xen29 and inhibited the biofilm formation, indicating the potential use of the designed peptides as antimicrobial treatment for wounds. The S-FE always showed better effects than C-FE, suggesting the benefit of H₂S during the elimination of bacteria. These antimicrobial H₂S-releasing APA hydrogels provide a new approach to treat burn wound infection and provide healing benefits due to the therapeutic effects of H₂S.

Throughout the study of polymer adsorption at the air/water and solid/water interfaces, surface tension measurements and surface plasmon resonance (SPR) spectroscopy have been identified as key methods for the acquisition of structural and thermodynamic information. These techniques were used to determine air/water and cellulose/water interfacial properties of pullulan (P) and pullulan cinnamates (PCs), 2-hydroxypropyltrimethylammonium xylans (HPMAXs), and hydroxypropyl xylans (HPXs). Hydrophobic modification of pullulan with cinnamate groups promoted adsorption onto model surfaces of regenerated cellulose. In order to understand the relative contributions of hydrophilic and hydrophobic interactions towards PC adsorption, PC adsorption onto self-assembled monolayers (SAMs) with different functional groups was also studied. As the degree of cinnamate substitution increased, greater adsorption onto cellulose, methyl-terminated SAMs (SAM-CH3), and hydroxyl-terminated SAMs (SAM-OH) was observed. This study showed that hydrogen bonding alone could not provide a complete explanation for PC adsorption onto cellulose. The adsorption of cationic 2-hydroxypropyltrimethylammonium (HPMA) xylans with different degrees of substitution (DS) onto SAMs and regenerated cellulose was studied by SPR. Surface concentration (Р) exhibited a maximum (Рmax) for HPMAX adsorption onto carboxylic acid-terminated SAMs (SAM-COOH) at an intermediate HPMA DS of 0.10. This observation was indicative of a relatively flat conformation for adsorbed HPMAXs with higher HPMA DS because of higher linear charge densities along the polymer backbone. Рobserved for HPMAX adsorption onto regenerated cellulose and SAM-OH surfaces was relatively low compared to HPMAX adsorption onto SAM-COOH surfaces. Surface tension measurements for aqueous solutions of HPX by the Wilhelmy plate technique showed that surface tension changes ("γ = γwater " γHPX(aq)) increased and critical aggregation concentrations generally decreased with increasing hydroxypropyl (HP) DS. Hence, even though HP substitution was necessary to induce aqueous solubility, excessive hydroxypropylation promoted aggregation in water. SPR studies indicated that HPXs did not adsorb significantly onto regenerated cellulose or SAM-OH surfaces (submonolayer coverage). In contrast, HPX did adsorb (~monolayer coverage) onto SAM-CH3 surfaces. Collectively, these studies showed natural polymers could be chemically modified to produce surface modifying agents with sufficient chemical control, whereby the surface properties of the resulting systems could be explained in terms of chemical structure and intermolecular interactions. / Ph. D.

Surfactants, polymers, and their mixtures are widely used in commercial formulations of paints, water-based adhesives, detergents, food, and other products. This thesis describes measurements of the forces acting on colloidal particles in surfactant and polymer solutions. The change in force on addition of surfactants and polymers is usually caused by adsorption to an interface. In this thesis, I also describe the effect of surface charge density, surface crystallinity, surface heterogeneity, and preadsorbed polymer on surfactant adsorption. A new method for the stabilization of colloidal particles is introduced via the synthesis and adsorption of unnatural proteins. Unnatural proteins can be synthesized using the natural "machinery" of a bacterial cell with almost any primary sequence, and provide an environmentally friendly route to colloidal stabilization. As a model system, we study the stabilization of alumina, because alumina has a high Hamaker constant and is therefore difficult to stabilize. An unnatural protein with the sequence, thioredoxin-Pro39Glu10 is used. The Glu10 is anionic (pH > 3) and is designed to adsorb to positively charged alumina (pH<9). The thioredoxin-Pro39 is hydrophilic so it should remain in solution, thereby providing a steric barrier to the approach of two particles in a range of salt and pH conditions. Ellipsometry experiments show that thioredoxin-Pro39Glu10 adsorbs to alumina. Force measurements with the Atomic Force Microscopy (AFM) colloid probe technique show that adsorption of the unnatural protein leads to repulsive forces that decay exponentially with the separation between the surfaces, and are independent of salt concentration. The loss of a salt-dependent force shows that adsorption of the unnatural protein has effectively neutralized the charge on the alumina. Thus, I have shown that an unnatural protein can be used to control the stability of a colloidal system. In general, the same hydrophilic block can probably be added to a variety of anchoring blocks to stabilize different colloidal particles. Electrostatic forces are frequently responsible for the stabilization of colloidal particles. The decay length of these forces is dictated by the electrolyte concentration. The relationship between the decay length and the concentration is well understood for fully dissociated 1:1 electrolytes. Here, I examine the decay-length in solutions where the ions associate strongly. The forces are measured between silica surfaces in aqueous carboxylic acid and surfactant solutions. The decay lengths of the electrostatic double-layer force in both these solutions are well described by the usual expression for decay length when the concentration of ions is obtained from an activity measurement. The effect of the surface properties of the solid substrate on surfactant adsorption is also described in this thesis. The adsorption characteristics of a charged surfactant onto fixed charged surfaces as a function of surface charge density is reported. This is the first time that a method has been introduced for making a series of known fixed charged surfaces. Investigating surfactant adsorption to these surfaces has improved our understanding of the role of charge density in surfactant adsorption and desorption. The desired surface charge density is achieved by the use of gold-thiol self-assembled monolayers (SAMs) of different Ï -groups ("OH and "N+(CH3)3). The mole fraction of "N+(CH3)3 on the mixed SAM dictates the surface charge density. The charge on "N+(CH3)3 is fixed and does not self-regulate. The adsorption of sodium dodecyl sulfate (SDS) to the interface between these model surfaces and aqueous solutions of SDS is investigated. Atomic Force Microscopy (AFM) of the adsorbed surfactant reveals no surface micelles above the critical micelle concentration, cmc, over a wide variety of "N+(CH3)3 densities. This shows that the lateral mobility of ions other than surfactant at the interface is important for the formation of surface micelles of ionic surfactants. Adsorption isotherms of SDS (with no added salt) measured by Surface Plasmon Resonance (SPR) show a plateau region in which the surface excess of SDS is equal to the known fixed surface charge. This demonstrates that the adsorption is electrostatically driven. There is no critical surface charge density at which adsorption rises rapidly. Thus there appears to be no 'hemimicelle concentration'. My work suggests that the formation of hemimicelles depends on the lateral mobility of the surface ions. Desorption experiments starting above the cmc show rapid desorption of SDS into water until the surface excess is equal to the surface charge density. The rapid desorption is followed by a much slower desorption. The elucidation of this fast-slow desorption pattern based on charge density is made possible by the preparation of a set of constant charge surfaces. / Ph. D.

The purpose of this thesis is to make a broadband antireflection coating configuration known as a quarter-wave stack consisting of one layer of titania and of one layer of silica nanoparticles. We utilize much that is already known about silica nanoparticle deposition. The first objective of this thesis is deposition and characterization of titania nanoparticle films deposited on glass microscope slides by a technique known as Ionic Self-Assembled Multilayers or ISAM deposition. This technique takes advantage of the electrostatic attraction between oppositely charged materials and ideally results in a uniform nanoparticle film whose thickness and optical properties can be tightly controlled. Deposition of a quarter-wave stack based on ISAM deposition of silica and titania nanoparticles is significantly simpler and less expensive than alternative deposition methods. Initial attempts to deposit titania films were unsuccessful because of excess diffuse scattering due to inhomogeneities in the film. In order to reduce diffuse scattering, two approaches were considered. The first approach was to improve the deposition process itself by experimenting with different values of deposition parameters such as solution pH and solution molarity. The other approach focused on removing the large nanoparticle aggregates from the colloidal solutions of titania nanoparticles that were suspected to be responsible for rough film surfaces resulting in diffuse scattering. This approach was successful. In addition, evidence suggested that surface roughness contributed more to diffuse scattering than the bulk of the films. After minimizing diffuse scattering from titania nanoparticle films, we used known results from research on silica nanoparticle films to deposit quarter-wave stacks consisting of one layer of titania nanoparticles with high refractive index and one layer of silica nanoparticles with low refractive index. This contrast in refractive indices is a desirable characteristic of quarter-wave stacks. The thicknesses and refractive indices of the two layers in the quarter-wave stacks were measured by ellipsometry and compared to the nominal thicknesses of these layers. Finally, the reflectance was derived from a model of the quarter-wave stack and was compared to the measured reflectance. It was found that construction of a quarter-wave stack by ISAM is possible but that it will be necessary to acquire data from more experiments. / Ph. D.

In today's market, companies are faced with pressure to increase variety in product offerings. While increasing variety can help increase market share and sales growth, the costs of doing so can be significant. Ultimately, variety causes complexity in products and processes to soar, which negatively impacts product development, quality, production scheduling, efficiency and more. Product variety is just one common cause of product complexity, a topic that several researchers have tackled with several sources of product complexity now identified. However, even with such progress, product complexity continues to be a theoretical concept, making it difficult for companies to fully implement advances and fully manage product complexity. More and more companies are relying on product family design to handle product variety. Broadly, a product family can be defined as a group of products sharing common elements. The advantages for companies using product family strategies can be significant: they enable efficient derivation of product variants, reduce inventory and handling costs, as well as setup and retooling time. The design challenge however, is to select the product platform to generate a variety of products with minimum deviation from individual requirements. Accordingly, the structure of product families makes designing and evaluating them a challenging process. In order to fully embrace the relationships between variety, product complexity, and product families an understanding of product complexity causes and impacts is essential. This research begins by introducing four main dimensions of product complexity within the context of a generalized definition. Product complexity indicators suitable in product design, development and production are derived. By establishing measurements for the identified indicators and using clustering techniques, a complexity evaluation approach for product family designs is also developed in this research. The evaluation approach is also applied on a component basis, to identify Critical Components that are main sources and contributors of complexity within product families. By standardizing identified Critical Components, product complexity levels and associated costs can be managed. A case application of three product families from a tire manufacturing company is used to verify that this research approach is suitable for evaluating and managing product complexity in product families. / Ph. D.

Detailed understanding of the kinetics and mechanisms of heterogeneous reactions between gas-phase nitrate radicals, a key nighttime atmospheric oxidant, and organic particles will enable scientists to predict the fate and lifetime of the particles in the atmosphere. In an effort to acquire knowledge of interfacial reactions of nitrate radical with organics, model surfaces are created by the spontaneous adsorption of methyl-/vinyl-/hydroxyl-terminated alkanethiols on to a polycrystalline gold substrate. The self-assembled monolayers provide a well-defined surface with the desired functional group (-CH3, H2C=CH-, or HO-) positioned precisely at the gas-surface interface. The experimental approach employs in situ reflection-absorption infrared spectroscopy (RAIRS) to monitor bond rupture and formation while a well-characterized flux of NO3 impinges on the organic surface. Overall, the reaction kinetics and mechanisms were found to depend on the terminal functional group of the SAM and incident energy of the nitrate radical (NO3). For reactions of the H2C=CH-SAM with NO3, the surface reaction kinetics obtained from RAIRS reveals that the consumption rate of the terminal vinyl groups is nearly identical to the formation rate of a surface-bound nitrate species and implies that the mechanism is one of direct addition to the vinyl group rather than hydrogen abstraction. Upon nitrate radical collisions with the surface, the initial reaction probability for consumption of carbon-carbon double bonds was determined to be (2.3 ± 0.5) -- 10-3. Studies of reactions of HO-SAM with the effusive source of NO3 suggest that the reaction between NO3 and the HO-SAM is initiated by hydrogen abstraction at the terminal - 'CH2OH groups with the initial reaction probability of (6 ± 1)-- 10-3. An Arrhenius plot was obtained to measure the activation energy of the H abstraction from the HO-SAM. Further, for reactions of the HO-SAM with the high incident energy of NO3 molecules created by molecular beam, the reaction probability for H abstraction at the hydroxyl terminus was determined to be ~0.4. The significant increase in the reaction probability was attributed to the promotion in the ability of NO3 abstracting hydrogen atom at the methylene groups along hydrocarbon chains. The reaction rates of NO3 with the model organic surfaces that have been investigated are orders of magnitude greater than the rate of ozone reactions on the same surfaces which suggests that oxidation of surface-bound organics by nighttime nitrate radicals may play an important role in atmospheric chemistry despite their relative low concentration. X-ray photoelectron spectroscopy (XPS) data suggests that oxidation of the model organic surfaces by NO3 leads to the production of organic nitrates, which are stable for a period time. In addition, the effect of background gases on reactions of NO3 with model organic surfaces needs further investigations at atmospheric pressures. The results presented in this thesis should help researchers to predict the fate and environmental impacts of organic particulates with which nitrate radicals interact. / Ph. D.

This thesis presents the characterization of the optical and mechanical properties of silica nanoparticle films fabricated by ionic self-assembly, also known as layer-by-layer (LbL) deposition. Utilizing electrostatic attraction of oppositely-charged materials permits uniform and rapid growth of the constituents onto planar and curved surfaces. In this work, silica nanoparticles are adsorbed onto glass and polycarbonate substrates, as well as micron-scale glass fibers, with the purpose of improving the optical quality of the respective media. Several methods are presented to improve the adhesion and cohesion of silica nanoparticle films on glass substrates. In the first method, the substrate and nanoparticle surfaces are coated with materials containing sulfonate end groups. Next, a photo-reactive polycation known as diazo-resin (DAR) is used in ISAM deposition with the modified silica nanoparticles. Subsequent exposure to UV converts the ionic bonds between the DAR and sulfonate groups into covalent ones. The second method to improve the mechanical strength is to heat the ISAM silica nanoparticle film at a high enough temperature (500 °C) to remove the polymer and partially fuse the nanoparticles. This technique is known as calcination and is shown to significantly improve the mechanical robustness of the film without compromising the optical properties. The final method involves the deposition of precursor and capping polymer layers around bulk silica nanoparticle films with both bilayer and quadlayer designs. The addition of these polymer layers improves the surface contact between adjacent nanoparticles but reduces the film porosity and consequently the optical transparency. Currently the calcination technique is the only one that significantly improves the film adhesion and cohesion, but suggestions are offered to potentially improve the performance of films made by the other two methods. An alternative way to functionalize polycarbonate substrates for silica nanoparticle ISAM deposition is also presented. The molecular structure of polycarbonate at the surface can be modified by exposing it to deep UV (λ = 185, 254 nm). By doing so, the surface becomes populated with carboxylate species, and thus permits ISAM deposition of poly(allylamine hydrochloride) (PAH) and silica nanoparticles. A variety of spectroscopic methods show that the molecular structure is changed by this procedure, and SEM shows that UV treatment improves the uniformity of ISAM films on polycarbonate. Finally, PAH/silica nanoparticle ISAM films are deposited onto glass fibers. The fibers are used for mechanical reinforcement of polymer composite optical media. The role of the nanoparticle film on the fibers is to reduce light scattering at the interfaces of materials with different thermo-optic coefficients, in other words, transmittance losses associated with changes in temperature. Fiber bundles coated with silica nanoparticles suffer from unacceptable levels of aggregation, and hence do not currently improve the transmittance over the temperature spectrum. Some evidence is presented, however, to suggest that the transparency can be improved if fiber aggregation during ISAM deposition can be avoided. / Ph. D.