Abstract This thesis has been made within the European Industrial Doctorate (EID) project called Mathematics and Materials Science for Steel Production and Manufacturing, abbreviated as MIMESIS, which has five partners: EFD Induction in Norway; SSAB, Outokumpu, and the University of Oulu in Finland; and Weierstrass Institute for Applied Analysis and Stochastics (WIAS) in Germany. The main aim of this work was to develop a steel composition and processing route suitable for making a slurry transportation pipeline with the aid of induction hardening, and to characterize the phase transformations and microstructures involved in the various stages of the processing route. A novel steel chemistry was designed based on metallurgical principles assisted by computational thermodynamics and kinetics. The designed composition is a medium-carbon, low-alloy steel microalloyed with niobium, in wt.% 0.40 C, 0.20 Si, 0.25 Mn, 0.50 Mo, 0.90 Cr, and 0.012 Nb. This was subsequently cast, thermomechanically rolled on a laboratory rolling mill to two bainitic microstructures, and finally subjected to the thermal cycles predicted to be encountered with the internal induction hardening of a typical pipe geometry. The phase transformations and microstructures found at various stages of the simulated production process have been characterized and algorithms developed to enable the optimization of microstructure and hardness through the pipe wall thickness. / Tiivistelmä Tämä väitöskirja on tehty osana Euroopan teollisuustohtori (European Industrial Doctorate, EID) -ohjelmaa projektissa eli Matematiikka ja materiaalitiede teräksen valmistuksessa ja käytössä (Mathematics and Materials Science for Steel Production and Manufacturing, MIMESIS). Ohjelmassa on viisi partneria: EFD Induction Norjasta; SSAB, Outokumpu ja Oulun yliopisto Suomesta; ja Weierstrass Institute for Applied Analysis and Stochastics (WIAS) Saksasta. Työn päätavoitteina oli kehittää teräksen koostumusta ja prosessointireittiä, jotka soveltuvat lietteen kuljetusputken valmistukseen induktiokarkaisun avulla, sekä karakterisoida prosessin eri vaiheiden aikana tapahtuvat faasimuutokset ja mikrorakenteet. Uusi teräskoostumus suunniteltiin metallurgisten periaatteiden pohjalta hyödyntämällä laskennallista termodynamiikkaa ja kinetiikkaa. Suunniteltu teräs on niobilla mikroseostettu, matalaseosteinen ja keskihiilinen, eli painoprosentteina 0,40 C, 0,20 Si, 0,25 Mn, 0,50 Mo, 0,90 Cr ja 0,012 Nb. Teräs valettiin, valssattiin ja jäähdytettiin termomekaanisesti laboratoriovalssaimella kahdeksi bainiittiseksi mikrorakenteeksi ja lopulta altistettiin lämpösykleille, joiden ennustettiin olevan tyypillisiä sisäisesti induktiokarkaistulle teräsputkelle. Simuloidun tuotantoprosessin eri vaiheissa havaitut faasimuutokset ja mikrorakenteet on karakterisoitu. Sen lisäksi on kehitetty algoritmit, jotka mahdollistavat mikrorakenteen ja kovuuden optimoinnin putken seinämän paksuuden läpi.

L’allégement des véhicules est l’un des objectifs prioritaires des constructeurs automobile pour répondre aux directives environnementales d’émission de CO2. Le développement des aciers multiphasés à très haute résistance mécanique est l’une des solutions communément adoptées pour réduire l’épaisseur des tôles dans les véhicules tout en conservant leur capacité à assurer la sécurité des passagers. La présente étude porte sur l’optimisation des paramètres du procédé de production industrielle de l’une des ces familles d’aciers : les aciers Dual Phase microalliés au titane et au niobium de haut grade ; c'est-à-dire possédant une résistance à la rupture supérieure à 800MPa.A partir d’une microstructure initiale bainite + martensite laminée à froid, les différents phénomènes se produisant au cours du recuit, de la chauffe jusqu’à la fin du maintien intercritique, sont caractérisés. L’influence des paramètres du recuit comme la vitesse de chauffe, la température et le temps de maintien est étudiée. Le système d’interactions triple entre la précipitation des éléments de microalliage, la recristallisation et la formation de l’austénite est au cœur du problème. Un scénario des évolutions microstructurales a été établi à partir de la caractérisation des divers phénomènes. La finesse de la microstructure étudiée (sub-micrométrique) a nécessité l’emploi combiné de techniques de caractérisation multi-échelles : MEB, MET, sonde atomique tomographique, nano-SIMS. / Lightening the weight of vehicles is one of the main challenging objectives of the automotive industry to reach the environmental regulation in term of CO2 emissions. The development of multiphase high strength steels is a common solution to reduce the thickness of sheet steel used in vehicles while keeping the same level of passenger’s safety requirements. The present study deals with the optimization of industrial process parameters applied to obtain one of these steels: the high strength microalloyed Dual Phase steels; i.e. with ultimate tensile strength superior to 800MPa.From an initial cold rolled microstructure made of bainite + martensite, the phenomena occurring during the annealing are characterized since the heating up to the end of the intercritical holding. The influence of process parameters as the heating rate, the holding temperature and the holding time are studied. The triple interactions system between the precipitation of microalloying elements, the recrystallization and the austenite formation is the core of the problem. A scenario of microstructural evolutions has been established based on the characterized phenomena. The studied fine microstructure (sub-microns) requires the combination of multiscale characterization techniques: SEM, TEM, atom probe tomography, nano-SIMS.

Les aciers multiphasés à très haute résistance mécanique destinés à l’industrie automobile font l’objet d’importantes activités de recherche et développement dans le contexte de l’allègement des structures. L’obtention de meilleurs compromis entre résistance et ductilité nécessite de comprendre l’influence du couple composition chimique nominale – paramètres du procédé d’élaboration sur la formation des microstructures.La présente étude s’inscrit dans cette démarche de compréhension et porte en particulier sur les mécanismes se produisant lors du recuit des nuances d’aciers Dual Phase de haut grade microalliés au Ti et au Nb, dont la microstructure initiale laminée à froid est composée de bainite et de martensite. Ces mécanismes (précipitation des éléments de microalliage Ti, Nb et Mo, recristallisation de la ferrite et formation de l’austénite) présentent des interactions complexes. Le scénario des évolutions microstructurales lors du recuit est caractérisé à l’aide d’une étude expérimentale s’appuyant sur des techniques d’analyses complémentaires à différentes échelles (DRX in situ, MEB, MET, SAT). L’influence respective des éléments de microalliage Ti, Nb et Mo et des paramètres du recuit sur ce scénario est clarifiée à l’aide d’une caractérisation systématique des évolutions microstructurales couplée à la mise en œuvre d’une démarche de modélisation des mécanismes et de leurs interactions. / To meet the need for weight reductions in the automotive industry, new advanced high-strength steels are being developed. The achievement of a better balance between high strength and high formability requires a deep understanding of both the effect of chemical composition and processing parameters on the formation of microstructures. The present work contributes to such an objective and deals with the mechanisms occurring during annealing of Dual Phase steels microalloyed with Ti and Nb. Microstructural changes during this stage include precipitation of microalloying elements, ferrite recrystallization and austenite formation. These mechanisms are investigated using complementary experimental techniques at different scales such as in situ XRD, SEM, TEM and APT in various Dual Phase steel grades having the same bainite-martensite initial cold-rolled microstructure. Using combined experimental and modeling approaches, the present work clarifies the separate influence of microalloying elements Ti, Nb and Mo and heating rate on the mechanisms occurring during annealing and their interactions.

Duplex stainless steels can be very attractive alternatives to austenitic grades due to their almost double strength at equal pitting corrosion resistance. When welding, the duplex alloys normally require addition of filler metal, while the commodity austenitic grades can often be welded autogenously. Over-alloyed consumables are used to counteract segregation of important alloying elements and to balance the two phases, ferrite and austenite, in the duplex weld metal. This work focuses on the weldability of the recently-developed lean duplex stainless steel LDX 2101® (EN 1.4162, UNS S32101). The pitting corrosion resistance of this grade is better than that of austenitic AISI 304 (EN 1.4307) and can reach the level of AISI 316L (EN 1.4404). The austenite formation is rapid in LDX 2101 compared to older duplex grades. Pitting resistance tests performed show that 1-2.5 mm thick laser and gas tungsten arc (GTA) welded LDX 2101 can have good corrosion properties even when welding autogenously. Additions of filler metal, nitrogen in the shielding gas, nitrogen-based backing gas and use of laser hybrid welding methods, however, increase the austenite formation. The pitting resistance may also be increased by suppressing formation of chromium nitrides in the weld metal and heat affected zone (HAZ). After thorough post-weld cleaning (pickling), pitting primarily occurred 1-3 mm from the fusion line, in the parent metal rather than in the HAZ. Neither the chromium nitride precipitates found in the HAZ, nor the element depletion along the fusion line that was revealed by electron probe microanalysis (EPMA) were found to locally decrease the pitting resistance. The preferential pitting location is suggested to be controlled by the residual weld oxide composition that varies over the surface. The composition and thickness of weld oxide formed on LDX 2101 and 2304 (EN 1.4362, UNS S32304) were determined using X-ray photoelectron spectroscopy (XPS). The heat tint on these lean duplex grades proved to contain significantly more manganese than what has been reported for standard austenitic stainless steels in the AISI 300 series. A new approach to heat tint formation is presented; whereby evaporation of material from the weld metal and subsequent deposition on the already-formed weld oxide are suggested to contribute to weld oxide formation. This is consistent with manganese loss from the weld metal, and nitrogen additions to the GTA shielding gas enhance the evaporation. The segregation of all elements apart from nitrogen is low in autogenously welded LDX 2101. This means that filler wire additions may not be required as for other duplex grades assuming that there is no large nitrogen loss that could cause excessive ferrite contents. As the nitrogen appears to be controlling the austenite formation, it becomes essential to avoid losing nitrogen during welding by choosing nitrogen-containing shielding and backing gas. / QC 20101213

<p>Duplex stainless steels are a very attractive alternative to austenitic grades due to their higher strength and good corrosion performance. The austenitic grades can often be welded autogenously, while the duplex grades normally require addition of filler metal. This is to counteract segregation of important alloying elements and to give sufficient austenite formation to prevent precipitation of chromium nitrides that could have a negative effect on impact toughness and pitting resistance. The corrosion performance of the recently-developed lean duplex stainless steel LDX 2101 is higher than that of 304 and can reach the level of 316. This thesis summarises pitting resistance tests performed on laser and gas tungsten arc (GTA) welded LDX 2101. It is shown here that this material can be autogenously welded, but additions of filler metal, nitrogen in the shielding gas and use of hybrid methods increases the austenite formation and the pitting resistance by further suppressing formation of chromium nitride precipitates in the weld metal. If the weld metal austenite formation is sufficient, the chromium nitride precipitates in the heat-affected zone (HAZ) could cause local pitting, however, this was not seen in this work. Instead, pitting occurred 1–3 mm from the fusion line, in the parent metal rather than in the high temperature HAZ (HTHAZ). This is suggested here to be controlled by the heat tint, and the effect of residual weld oxides on the pitting resistance is studied. The composition and the thickness of weld oxide formed on LDX 2101 and 2304 were determined using X-ray photoelectron spectroscopy (XPS). The heat tint on these lean duplex grades proved to contain significantly more manganese than what has been reported for standard austenitic stainless steels in the 300 series. A new approach on heat tint formation is consequently presented. Evaporation of material from the weld metal and subsequent deposition on the weld oxide are suggested to contribute to weld oxide formation. This is supported by element loss in LDX 2101 weld metal, and nitrogen additions to the GTA shielding gas further increase the evaporation.</p><p> </p>

Duplex stainless steels are a very attractive alternative to austenitic grades due to their higher strength and good corrosion performance. The austenitic grades can often be welded autogenously, while the duplex grades normally require addition of filler metal. This is to counteract segregation of important alloying elements and to give sufficient austenite formation to prevent precipitation of chromium nitrides that could have a negative effect on impact toughness and pitting resistance. The corrosion performance of the recently-developed lean duplex stainless steel LDX 2101 is higher than that of 304 and can reach the level of 316. This thesis summarises pitting resistance tests performed on laser and gas tungsten arc (GTA) welded LDX 2101. It is shown here that this material can be autogenously welded, but additions of filler metal, nitrogen in the shielding gas and use of hybrid methods increases the austenite formation and the pitting resistance by further suppressing formation of chromium nitride precipitates in the weld metal. If the weld metal austenite formation is sufficient, the chromium nitride precipitates in the heat-affected zone (HAZ) could cause local pitting, however, this was not seen in this work. Instead, pitting occurred 1–3 mm from the fusion line, in the parent metal rather than in the high temperature HAZ (HTHAZ). This is suggested here to be controlled by the heat tint, and the effect of residual weld oxides on the pitting resistance is studied. The composition and the thickness of weld oxide formed on LDX 2101 and 2304 were determined using X-ray photoelectron spectroscopy (XPS). The heat tint on these lean duplex grades proved to contain significantly more manganese than what has been reported for standard austenitic stainless steels in the 300 series. A new approach on heat tint formation is consequently presented. Evaporation of material from the weld metal and subsequent deposition on the weld oxide are suggested to contribute to weld oxide formation. This is supported by element loss in LDX 2101 weld metal, and nitrogen additions to the GTA shielding gas further increase the evaporation. / QC 20101126