This study seeks to expand the range of climates and conditions in which free cooling from an economizer can replace air conditioning power consumption in residential applications. To explore this issue, we first discretize a simple building model in space and in time. We then solve the associated energy and mass balances for the estimated hourly heating and cooling loads and humidity conditions with respect to an annual climate profile. We propose a forecast-based algorithm to control the rate of outdoor airflow brought in by an economizer, in response to the upcoming cooling load to be experienced by the interior airspace. The algorithm takes advantage of a range of acceptable temperatures for thermal comfort by precooling the envelope overnight to delay the onset of cooling demand during the day. In order to consider the highest potential benefit from such an algorithm, we bypass the considerable problem of forecast accuracy by basing the inputs on the upcoming cooling load according to an initial simulation of the full year. On the whole, even with the forecast-based control, the results of the study have much in common with previous findings in the literature. Precooling works better to reduce cooling load in cases of higher thermal and moisture mass, but a humid climate severely restricts when free cooling is beneficial. For the example house considered here with the Austin climate and other assumptions, the effect of the proposed forecast-based economizer control was to greatly reduce the indoor air cooling load while greatly increasing the number of annual hours of unacceptably high indoor humidity. When we adjusted the forecast-based algorithm to avoid the excess humidity, the remaining reduction in cooling load was not significant. To investigate further how a forecast-based economizer could reduce cooling load in humid climates, the prinicipal task should be to extend the control algorithm to forecast and manage upcoming indoor humidity levels in the same fashion as was done in this study for indoor air temperature. / text

The building sector alone accounts for almost 40% of the total energy demand and people spend more than 80% of their time indoors. Reducing energy demand in buildings is essential to the achievement of a sustainable built environment. At the same time, it is important to not deteriorate people’s health, well-being and comfort in buildings. Thus, designing healthy and energy-efficient buildings is one of the most challenging tasks. Evaluation of buildings with a broad perspective can give further opportunities for energy savings and improvement of the indoor climate. The aim of this thesis is to understand the functionality, regarding indoor climate and energy performance, of a low-energy building. To achieve this, a multi-dimensional approach is used, which means that the building is investigated from several points of views and with different methods. A systems approach is applied where the definition of the system, its components and the border to its environment, is essential to the understanding of a phenomenon. Measurement of physical variables, simulations, and qualitative interviews are used to characterize the performance of the building. Both energy simulation and computational fluid dynamic simulations are used to analyse the energy performance at the building level as well as the indoor climate at room level. To reveal the environmental impact of the low-energy building studied in this thesis the CO2 emissions and embodied energy have been investigated regarding different surrounding energy systems. The evaluated building is situated at the west coast of Sweden and uses about 50% of energy compared to a comparable ordinary Swedish building. The building is well-insulated and an air-to-air heat exchanger is used to minimise the heat losses through ventilation. The houses are heated mainly by the emissions from the household appliances, occupants, and by solar irradiation. During cold days an integrated electrical heater of 900 W can be used to heat the air that is distributed through the ventilation system. According to measurements and simulations, the ventilation efficiency and thermal environment could be further improved but the occupants are mostly satisfied with the indoor climate. The control of the heating system and the possibility for efficient ventilation during summertime are other important issues. This was found through quantitative measurements, simulations and qualitative interviews. The low-energy building gives rise to lower CO2 emissions than comparable buildings, but another energy carrier, such as district heating or biofuel, could be used to further improve the environmental performance of the building. The total energy demand, including the embodied energy, is lower than for a comparable building. To understand the functionality of a low-energy building both the technical systems and the occupants, who are essential for low-energy buildings, partly as heat sources but mainly as users of the technical systems, should be included in the analysis.

This study developed and applied a field test to evaluate the American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE)/Chartered Institute of Building Services Engineers (CIBSE)/United States Green Building Council (USGBC) Performance Measurement Protocols (PMP) for Commercial Buildings in a case-study office building in central Texas. As the first integrated protocol on building performance measurement, the ASHRAE PMP accomplished its goal of providing the standardized protocols for measuring and comparing the overall performance of a building, including energy, water, thermal comfort, Indoor Air Quality (IAQ), lighting, and acoustics. However, several areas for improvement were identified such as conflicting results from different procedures or benchmarks provided in the ASHRAE PMP; limited guidelines for performing the measurements; lack of detailed modeling techniques, graphical indices, and clear benchmarks; and some practical issues (i.e., high cost requirements and time-intensive procedures). All these observations are listed as the forty issues, including thirteen for energy, five for water, and twenty-two for Indoor Environmental Quality (IEQ). Recommendations were developed for each issue identified. For the selected high-priority issues, twelve new or modified approaches were proposed and then evaluated against the existing procedures in the ASHRAE PMP. Of these twelve new or modified approaches, the following are the most significant developments: a more accurate monthly energy use regression model including occupancy; a monthly water use regression model for a weather-normalized comparison of measured water performance; a method how to use a vertical temperature profile to evaluate room air circulation; a method how to use LCeq – LAeq difference as a low-cost alternative to estimate low frequency noise annoyance; a statistical decomposition method of time-varying distribution of indices; and a real-time wireless IEQ monitoring system for the continuous IEQ measurements. The application of the forty recommendations and the twelve new or modified approaches developed in this study to the ASHRAE PMP is expected to improve the applicability of the ASHRAE PMP, which aligns the overall purpose of this study. Finally, this study developed a new single figure-of-merit rating system based on the ASHRAE PMP procedures. The developed rating system is expected to improve the usability of the protocols.

This Thesis is focused on the study of the problem of condensation on the inner surface of Fullrigaren building’s large single pane window. This has serious consequences as water on the floor, corrosion or mould growth. As the climate in Nordic countries is cold for several months a year, windows are a crucial part in building envelopes. Condensation on a window may be suitably discussed only with respect to the climate considered as cold, moderate and warm climates pose different requirements on the windows, and this is why a characterization of Gävle by its climate is necessary. This Thesis will include the energy analysis of the staircase considered which is required to understand the source of the actual problem. Both heat and moisture transfer will be studied. In this purpose, an IDA model will be built to simulate the conditions throughout the year and hand-made calculations will be done for the average and most critical situations. The results show that condensation will already occur for the monthlyaverage conditions having as an additional problem that if temperature drops below zero it will freeze. Results will also be compared to an initial installation of a 2 pane window reaching as a conclusion that its original installation would had avoided the problems for most of the time. The Thesis will end with several proposals posed to solve the problem by either increasing the temperature or reducing the moisture content of the ambient air, and the selection of the best one. The final aim of the Thesis is to achieve an energy efficient window which should provide good lighting during the day and good thermal comfort both during day and night at minimum demand of paid energy. And for this, the selection of the electrically heated window is proposed.

Advanced Building Energy Data Visualization is a way to detect performance problems in commercialbuildings. By placing sensors in a building that collects data from example, air temperature and electricalpower, then makes it possible to calculate the data in Data Visualization software. This softwaregenerates visual diagrams so the building manager or building operator can see if for example thepower consumption is to high.A first step (before sensors are installed in a building) to see how the energy consumption is in abuilding can be to use a Benchmarking Tool. There is a number of Benchmarking Tools that is availablefor free on the Internet. Each tool have a bit different approach, but they all show how much energyconsumption there is in a building compared to other similar buildings.In this study a new web design for the benchmarking tool CalARCH has been developed. CalARCHis developed at the Berkeley Lab in Berkeley, California, USA. CalARCH uses data collected only frombuildings in California, and is only for comparing buildings in California with other similar buildingsin the state.Five different versions of the web site were made. Then a web survey was done to determine whichversion would be the best for CalARCH. The results showed that Version 5 and Version 3 was the best.Then a new version was made, based on these two versions. This study was made at the LawrenceBerkeley Laboratory.

In the quest for improving building energy efficiency raising the level of performance of the building enclosure has become critical. As the thermal performance of the building enclosure improves so does the overall energy efficiency of the building. One key component in determining the energy performance of the building enclosure is windows. Windows have an integral role in determining the energy performance of a building by allowing light and heat from the sun to enter into a space. Energy efficient buildings take advantage of this free solar energy to help offset heating energy consumption and electric lighting loads. However, windows are traditionally the least insulating component of the modern building assembly. With excessive use, larger window areas can lead to greater occupant discomfort and energy consumption from greater night-time heat loss, higher peak and total cooling energy demand from unwanted solar gains, and discomfort glare. As a result, windows must be carefully designed to not only minimize heat loss, but also effectively control solar gains to maintain both a thermally and visually comfortable environment for the appropriate climate region and orientation. In this thesis, a complete analysis of window assemblies for commercial office buildings is presented. The analysis is divided into three sections: the Insulated Glazing Unit (IGU), the Curtain Wall Section (frames), and the overall energy performance of a typical office building. The first section investigates the performance characteristics of typical and high performance IGUs, specifically its insulating value (Ucg), its solar heat gain properties (Solar Heat Gain Coefficient, SHGC), and its visual transmittance (VT) through one-dimensional heat transfer and solar-optical modeling. Mechanisms of heat transfer across IGUs were investigated giving insight into the parameters that had the most significant effect on improving each performance characteristic. With a through understanding of IGU performance, attainable performance limits for each of property were generated from combining of different glazing materials, fill gases, and coatings. Through the right combination of materials IGU performance can be significantly altered. The U-value performance of IGUs ranges from 2.68 W/m2K (R-2.1) for a double-glazed, clear, air filled IGU to 0.27 W/m2K (R-21) for a quint-glazed, low-E, xenon filled high performance IGU. The second part of the thesis looks at the thermal performance of curtain wall sections that hold the IGU through two-dimensional heat transfer modeling. Similar to the IGUs, heat transfer mechanisms were studied to by substituting different materials to determine which components are crucial to thermal performance. From this analysis improvements were made to typical curtain wall design that significantly reduces the overall heat transfer within the frame section, producing a high performance curtain wall section. With simple modifications, a high performance curtain wall section can reduce its U-value by as much as 81% over a typical curtain wall section, going from 13.39 W/m2K to 2.57 W/m2K. Thus significantly reducing the U-value of curtain wall systems, particularly for smaller windows. The final part of the thesis examines the impact of typical and high performance windows on the energy performance of perimeter offices of a high-rise commercial building located in Southern Ontario. An hourly simulation model was set up to evaluate both the annual and peak energy consumption of a typical perimeter office space. The office faced the four cardinal directions of north, east, south, and west to evaluate the effect of orientation. The model also included continuous dimming lighting controls to make use of the available daylight. The effect of exterior shading on perimeter space energy performance was also investigated with both dynamic and static exterior shading devices. The results of the simulations revealed that window properties have very little influence on the energy performance of a high internal heat gain office, that is typical of older offices with less energy efficient office equipment and lighting and a higher occupant density. Conversely, window properties, particularly the insulating value of the window, has a greater effect on the energy performance of a mid to low internal heat gain office that is typical of most modern day commercial buildings. The results show windows with lower U-values yet higher SHGC are preferred over windows of similar U-values but with lower SHGC. The results also indicate that both static and dynamic shading have very little effect on energy performance of mid to low internal heat gain offices. From this analysis optimal window areas in the form of window-to-wall ratios (WWR) are presented for each orientation for mid to low internal heat gain offices. The optimal WWR for south-facing facades are between 0.50 to 0.66, and 0.30 to 0.50 for east-, west-, and north-facing facades, while for high internal heat gain perimeter spaces window areas should be kept to a minimum.

In the aspects of global sustainability, buildings are known to be one of the largest energy consumers. Though sustainable building construction through technological advances is helping in achieving environment friendly buildings, a considerable amount of energy is also being consumed by existing buildings. While many factors at all different stages of building life are responsible for this, the building material is one of the most important considerations. Glass being the most sensitive building material can lead to high energy consumption in the building if used in an improper way. This study takes this factor into account, and tries to investigate the potential of energy savings in buildings through the simple and basic considerations in design. An energy analysis model of an existing academic building in College Station, Texas was developed using Design Builder computer simulation software. This model was then analyzed for the total amount of energy consumption in the base case. The existing building model was then modified by replacing the glass used for external fenestrations. Latest building codes and standards for the site location, glass properties, and parametric simulation results were taken into consideration. Again the model was simulated for annual energy consumption and the results are noted. This formed the first option for the retrofitting scenario. A hypothetical redesign scenario was also established in which the revision of building orientation was taken into consideration. The building was re-oriented to suit the weather conditions and recommendations by Advanced Energy Design Guidelines (30 percent energy savings over ASHRAE Standard 90.1-1999). The building was then simulated for annual energy consumption. A comparative analysis was performed between the three cases and the study concluded by showing 23 percent savings in the annual fuel consumption, 23.35 percent reduction in CO2 emission of the building and 25 percent reduction in annual solar heat gain under Modified case 1. Modified case 2, however, did not show any further savings due to the form of the building (almost square). However, modified case 1 settings emitted 31.8 percent more CO2 over the Energy Star office building in Texas. This methodology sets up a set of guidelines which can be followed while investigating a building for minimum annual energy consumption.

Being located in subtropical area, the weather in Taiwan is hot and humid which imposing huge cooling load on buildings. Conventionally, central air-conditioning plants were designed using refrigerant compressors to make chilled water, and then pumped through the zone pumps to meet the cooling load, providing air-conditioning by Fan Coil Unit (FCU) or Air-Handling Units (AHU) by ductwork. To meet the varying cooling demand, two important systems were developed for energy savings, namely, the Variable Water Volume (VWV) system, and the Variable Air Volume (VAV) system, which has been widely adapted in Taiwan area. The working principle is mainly devoted to adjusting the volume of the chilled water and/or air volume delivered through inverter-driven pimps and fans to achieve energy saving. On the other hand, recently in Japan, an important energy-saving air-conditioning system has been developed which directly varying the refrigerant flow rate to meet the varying cooling demand by inverter-driven compressors, named VRV system. Comparative to the conventional air-conditioning system, the heat exchange mechanism of the VRV system has been effectively enhanced by direct exchange of the refrigerant and the cool air, which is in effect a combination of the VWV and VAV system. It provided huge energy saving potential for the application on buildings with moderate cooling loads, such as 100 USRT or so. It is the goal of this research project, to evaluate the performance of the VRV system in Taiwan¡¦s hot and humid climate, by performing full-scale experimental investigation so that energy savings effect can be validated quantitatively. Since VRV system is fairly new in Taiwan, the validation of the system performance under local weather condition is of particular importance. It is anticipated that through the changing of the operation conditions, such as different outdoor conditions, various partial load conditions, and different scheduling of the VRV system, the power consumption of the VRV vs. conventional system can be compared precisely and quantitatively. These experimental data will, in turn, provides valuable reference to the establishment of the building energy consumption index in Taiwan, which outwits the direct adoption of the foreign data such as from Japan, in achieving a much reliable database.

The aim of this study was to investigate the thermal performance of residential units in the Middle East Technical University (METU) Campus, Ankara. The study was conducted on the unoccupied residential units to eliminate the occupant interventions. There were only three unoccupied residential units in the study period, hence sample was considered as randomly selected. Case study units were triplex row houses and all physical characteristics were identical apart from their orientations. The thermal performance of these three residential units was assessed by compiling data on temperature and relative humidity from a number of their rooms on certain days in January and February. The study was conducted in winter months, because heating loads are more significant than cooling loads for energy consumption in Ankara / the measurement period was determined according to the coldest days of the year. In this context, the temperature and humidity charts were evaluated and one of the units was simulated using the software tool Ecotect v.5.20. The simulation temperature charts demonstrate similar behavior and trends as the measured temperature / although, it was approximately 4 0C lower than the measured temperature. The possible reason for such a difference may be the precision of the material properties. Six different calibrations were tested by changing the thermal properties of the envelope materials to obtain comparable results with the measured temperature readings. Based on the calibrated model, it was found that an increase in the U-value of the envelope materials did not have a significant effect on the simulated temperature charts.

This dissertation provides one methodology to determine potential energy savings of buildings with limited information. This methodology is based upon the simplified energy analysis procedure of HVAC systems and the control of the comfort conditions. Numerically, the algorithm is a tailored exhaustive search over all the independent variables that are commonly controlled for a specific type of HVAC system. The potential energy savings methodology has been applied in several buildings that have been retrofitted and/or commissioned previously. Results from the determined savings for the Zachry building at Texas A&M after being commissioned show a close agreement to the calculated potential energy savings (about 85%). Differences are mainly attributed to the use of simplified models. Due to the restriction of limited information about the building characteristics and operational control, the potential energy savings method requires the determination of parameters that characterize its thermal performance. Thus, a calibrated building is needed. A general procedure has been developed to carry out automated calibration of building energy use simulations. The methodology has been tested successfully on building simulations based on the simplified energy analysis procedure. The automated calibration is the minimization of the RMSE of the energy use over daily conditions. The minimization procedure is fulfilled with a non-canonical optimization algorithm, the Simulated Annealing, which mimics the Statistical Thermodynamic performance of the annealing process. That is to say, starting at a specified temperature the algorithm searches variable-space states that are steadier, while heuristically, by the Boltzmann distribution, the local minima is avoided. The process is repeated at a new lower temperature that is determined by a specific schedule until the global minimum is found. This methodology was applied to the most common air-handler units producing excellent results for ideal cases or for samples modified with a 1% white noise.