The aim of this project is to design a microstrip phase array antenna in ADS (Advance Design System) Momentum. The resonant frequency of which is 10 GHz. Two circular patches with a radius of 5.83 mm each are used in designing the array antenna. RT-DURROID 5880 is used as a substrate for this microstrip patch array design. These circular patches are excited using coaxial probe feed and transmission lines of particular lengths and widths. These transmission lines perfectly match the impedance of the circular patches. Various parameters, for example the S-parameters, two dimensional and three dimensional radiation patterns, excitation models, gain, directivity and efficiency of the designed antenna are obtained from ADS Momentum.

Yes / Recent studies and research have centred on new solutions in different elements and stages to the increasing energy and data rate demands for the fifth generation and beyond (B5G). Based on a new-efficient digital beamforming approach for 5G wireless communication networks, this work offers a compact-size circular patch antenna operating at 60 GHz and covering a 4 GHz spectrum bandwidth. Massive Multiple Input Multiple Output (M–MIMO) and beamforming technology build and simulate an active multiple beams antenna system. Thirty-two linear and sixty-four planar antenna array configurations are modelled and constructed to work as base stations for 5G mobile communication networks. Furthermore, a new beamforming approach called Projection Noise Correlation Matrix (PNCM) is presented to compute and optimise the fed weights of the array elements. The key idea of the PNCM method is to sample a portion of the measured noise correlation matrix uniformly in order to provide the best representation of the entire measured matrix. The sampled data will then be utilised to build a projected matrix using the pseudoinverse approach in order to determine the best fit solution for a system and prevent any potential singularities caused by the matrix inversion process. The PNCM is a low-complexity method since it avoids eigenvalue decomposition and computing the entire matrix inversion procedure and does not require including signal and interference correlation matrices in the weight optimisation process. The suggested approach is compared to three standard beamforming methods based on an intensive Monte Carlo simulation to demonstrate its advantage. The experiment results reveal that the proposed method delivers the best Signal to Interference Ratio (SIR) augmentation among the compared beamformers

This master’s thesis describes the design, implementation and testing of an active antenna intended for use with global navigation satellite systems. The active antenna is composed of two major parts, a dual-band circular patch antenna and a dual-band low-noise amplifier. To streamline the design process, a modular solution was adopted. This enabled the functionality of every part in the signal path to be verified before the final active antenna was designed. A practical method to develop dual-band stacked circular patch antennas, along with a systematic way to tune the resonant frequencies and impedance of the antenna, is also presented. Testing of the antenna in realistic scenarios shows that the active antenna performs as expected and predicted by simulations. / <p>Examensarbetet är utfört vid Institutionen för teknik och naturvetenskap (ITN) vid Tekniska fakulteten, Linköpings universitet</p>

In this study we tried to design a microstrip antenna, to get a suitable radiation pattern for a LEO satellite. Our aim is to get a radiation pattern that has a maximum power which is not in the broadside direction to the antenna surface / instead broadside radiation has a relatively lower power density. Maximum power radiation is desired to be at about 30 &ndash / 50 degrees angle beyond the normal to the antenna surface. We desire circularly polarized radiation. We used two concentric antennas / one is a circular patch at the center and the other is an annular ring which is used at the outer region. By using Ansoft Ensemble 8.0 software, we design an antenna which has a resonance frequency at 8.2 GHz. Using the result of the program we design the real antenna. The measurement results are compared with the simulation results.

Made available in DSpace on 2014-12-17T14:55:07Z (GMT). No. of bitstreams: 1 ClarissaLN.pdf: 3152047 bytes, checksum: a2e14bfa9e4c314444ebb4284dc7608b (MD5) Previous issue date: 2008-10-21 / Coordena??o de Aperfei?oamento de Pessoal de N?vel Superior / This work presents a theoretical and experimental investigation about the properties of microstrip antennas for ultra-wideband systems. Configurations of elliptic monopoles with different eccentricities and circular monopoles are considered. Two prototypes for each antenna configuration were built, one with the typical microstrip configuration and the other is similar to the first, except for a small aperture in the ground plane. Therefore, this work proposes to modify the configuration of the ground plane of the monopoles designed adding a rectangular stub, in order to optimize and improve the performance of such structures. The obtained results show that the introduction of that rectangular aperture in the ground plane allows an improvement of the frequency response for the considered antenna propotypes. It is observed a good agreement between the measured and simulated results. Finally, some proposals for future works are presented / Este trabalho apresenta uma investiga??o te?rica e experimental sobre as propriedades de antenas de microfita para sistemas de banda ultra larga. S?o consideradas configura??es de monopolos el?pticos com excentricidades diferentes, e monopolos circulares. Foram constru?dos dois prot?tipos para cada configura??o de antena, um com a configura??o t?pica de microfita e outro similar ao primeiro, mas com uma pequena abertura no plano de terra. Assim, este trabalho objetiva modificar a configura??o do plano de terra dos monopolos projetados atrav?s da inser??o de um recorte retangular, para fins de otimiza??o e melhoria nos desempenhos das estruturas. Os resultados obtidos mostram que a introdu??o dessa abertura retangular no plano de terra permite melhorar a resposta em freq??ncia das antenas consideradas. Observa-se uma boa concord?ncia entre os resultados medidos e simulados. Algumas propostas para a realiza??o de trabalhos futuros s?o apresentadas

No description available.