This study developed a reinforced steel rod bending machine for rods with diameters of up to 8 mm and annealed wire cutter for up to 5 kg for replacing manual intervention required to bend rods in reinforced concrete columns. This study aims to reduce the physical effort that could lead to occupational diseases, such as tenosynovitis, bursitis, muscle disorders. Clamp manufacturing possesses great risk for workers, who are exposed to injuries while using different cutting devices, such as grinders and electric saws. They also face potential problems such as muscular fatigue due to the nonergonomic and repetitive work positions. The proposed machine features a mechanical dragging and bending systems and manual shears. Additionally, the proposed machine has been designed theoretically and its effectiveness has been assessed through simulations conducted using the SolidWorks CAD software. A bending machine prototype for producing clamps is developed and its machine productivity is measured. Using this machine, approximately 300 clamps can be bent per hour without possessing any risk to the worker.

Doctor of Philosophy / Department of Civil Engineering / Hayder Rasheed / The analysis of concrete columns using unconfined concrete models is a well established practice. On the other hand, prediction of the actual ultimate capacity of confined concrete columns requires specialized nonlinear analysis. Modern codes and standards are introducing the need to perform extreme event analysis. There has been a number of studies that focused on the analysis and testing of concentric columns or cylinders. This case has the highest confinement utilization since the entire section is under confined compression. On the other hand, the augmentation of compressive strength and ductility due to full axial confinement is not applicable to pure bending and combined bending and axial load cases simply because the area of effective confined concrete in compression is reduced. The higher eccentricity causes smaller confined concrete region in compression yielding smaller increase in strength and ductility of concrete. Accordingly, the ultimate confined strength is gradually reduced from the fully confined value fcc (at zero eccentricity) to the unconfined value f’c (at infinite eccentricity) as a function of the compression area to total area ratio. The higher the eccentricity the smaller the confined concrete compression zone. This paradigm is used to implement adaptive eccentric model utilizing the well known Mander Model and Lam and Teng Model. Generalization of the moment of area approach is utilized based on proportional loading, finite layer procedure and the secant stiffness approach, in an iterative incremental numerical model to achieve equilibrium points of P- and M- response up to failure. This numerical analysis is adaptod to asses the confining effect in circular cross sectional columns confined with FRP and conventional lateral steel together; concrete filled steel tube (CFST) circular columns and rectangular columns confined with conventional lateral steel. This model is validated against experimental data found in literature. The comparison shows good correlation. Finally computer software is developed based on the non-linear numerical analysis. The software is equipped with an elegant graphics interface that assimilates input data, detail drawings, capacity diagrams and demand point mapping in a single sheet. Options for preliminary design, section and reinforcement selection are seamlessly integrated as well. The software generates 2D interaction diagrams for circular columns, 3D failure surface for rectangular columns and allows the user to determine the 2D interaction diagrams for any angle  between the x-axis and the resultant moment. Improvements to KDOT Bridge Design Manual using this software with reference to AASHTO LRFD are made. This study is limited to stub columns.

Doctor of Philosophy / Department of Civil Engineering / Hayder Rasheed / Recent applications in reinforced concrete columns, including strengthening and extreme loading events, necessitate the development of specialized nonlinear analysis methods to predict the confined interaction domain of axial force, shear, and bending moment in square and slightly rectangular concrete columns. Fiber-reinforced polymer (FRP) materials are commonly used in strengthening applications due to their superior properties such as high strength-to-weight ratio, high energy absorption and excellent corrosion resistance. FRP wrapping of concrete columns is done to enhance the ultimate strength due to the confinement effect, which is normally induced by steel ties. The existence of the two confinement systems changes the nature of the problem. Existing research focused on a single confinement system. Also, very limited research on rectangular sections was found in the literature. In this research, a model to estimate the combined behavior of the two systems in rectangular columns is proposed. The calculation of the effective lateral pressure is based on Lam and Teng model and Mander model for FRP wraps and steel ties, respectively. The proposed model introduces load eccentricity as a parameter that affects the compression zone size, and in turn the level of confinement engagement. Full confinement corresponds to zero eccentricity, while unconfined behavior corresponds to infinite eccentricity. The model then generates curves for eccentricities within these boundaries. The numerical approach developed has then been extended to account for shear interaction using the simplified modified compression field theory adopted by AASHTO LRFD Bridge Design Specifications 2014. Comparisons were then performed against experimental data and Response-2000, an analytical analysis tool based on AASHTO 1999 in order to validate the interaction domain generated. Finally, the developed models were implemented in the confined analysis software “KDOT Column Expert” to add FRP confinement effect and shear interaction.

Alkali silica reaction (ASR) and delayed ettringite formation (DEF) are two causes of concrete deterioration. Both mechanisms cause expansion of concrete and thus extensive cracking. Most previous research on ASR and DEF focused on understanding the material science of the mechanisms. This dissertation adds to the smaller body of knowledge about ASR/DEF’s effect on the structural behavior of reinforced concrete columns. It compares the structural performance of ASR/DEF affected concrete columns to mechanically cracked columns, evaluates the relative performance of four different concrete repair methods for strengthening damaged columns, and describes how to model pre-existing cracks in the finite element program ATENA. Previous research on scaled columns used mechanically cracked concrete as an approximation of ASR/DEF cracking damage. These earlier column tests, by Kapitan, were compared to two columns affected by ASR/DEF. Due to a deficiency in original design of the actual columns modeled, all of these scaled column specimens failed in bearing during testing under biaxial bending. The ASR/DEF affected columns exhibited nearly identical performance (including bearing capacity) as Kapitan’s control specimen. Thus, with over one percent expansion due to ASR/DEF, there was no reduction in bearing capacity for these columns. Based on the bearing failure observed in these scaled column specimens, concrete repairs were designed to increase confinement of the column capital to address the bearing capacity deficiency. A series of bearing specimens was constructed, externally reinforced using four different strengthening schemes, and load tested. From this bearing specimen series, both an external post-tensioned repair and a concrete jacketing repair performed well beyond their designed capacities and are recommended for bearing zone confinement repair of similar ASR/DEF affected concrete columns. Further, this dissertation presents how Kapitan’s scaled column results were modeled using ATENA (a reinforced concrete finite element program). A technique for modeling the mechanical cracking was developed for ATENA. Once calibrated, a parametric study used the model to find that a 0.17-inch wide through-section crack in the scaled columnd (5/8 inches in the field) was the threshold that reduced capacity of the scaled column to the factored design load. / text

The need to satisfy aerospace industry's demand not met by traditional materials motivated researchers and scientists to look for new solutions. The answer was found in developing new material systems by combining together two or more constituents. Composites, also known as fiber reinforced polymers (FRP) consisting of a reinforcing phase (fibers) embedded into a matrix (polymer), offered several advantages with respect to conventional materials. High specific modulus and strength together with other beneficial properties, corrosion resistance and transparency to electrical and magnetic fields above all, made FRP also suitable for use as construction materials in structural engineering. In the early years of the twenty-first century, the publication by the American Concrete Institute (ACI) of design guidelines for the use of FRP as internal reinforcement and for external strengthening of concrete members accelerated their implementation for structural engineering applications. To date, FRP have gained full acceptance as advanced materials for construction and their use is poised to become as routine as the use of conventional structural materials such as masonry, wood, steel, and concrete. However, new concrete columns internally reinforced with FRP bars and FRP confinement for existing prismatic reinforced concrete (RC) columns have currently important unsolved issues, some of which are addressed in this dissertation defense. The dissertation is articulated on three studies. The first study (Study 1) focuses on RC columns internally reinforced with glass FRP (GFRP) bars; the second (Study 2) on RC prismatic columns externally confined by means of FRP laminates using glass and glass/basalt fibers; and the third (Study 3) is a theoretical attempt to interpret and capture the mechanics of the external FRP confinement of square RC columns. Study 1 describes an experimental campaign on full-scale GFRP RC columns under pure axial load undertaken using specimens with a 24 by 24 in. (0.61 by 0.61 m) square cross section. The study was conducted to investigate whether the compressive behavior of longitudinal GFRP bars impacts the column performance, and to understand the contribution of GFRP ties to the confinement of the concrete core, and to prevent instability of the longitudinal reinforcement. The results showed that the GFRP RC specimens behaved similarly to the steel RC counterpart, while the spacing of the ties strongly influenced the failure mode. Study 2 presents a pilot research that includes laboratory testing of full-scale square and rectangular RC columns externally confined with glass and basalt-glass FRP laminates and subjected to pure axial load. Specimens that are representative of full-scale building columns were designed according to a dated ACI 318 code (i.e., prior to 1970) for gravity loads only. The study was conducted to investigate how the external confinement affects ultimate axial strength and deformation of a prismatic RC column. The results showed that the FRP confinement increases concrete axial strength, but it is more effective in enhancing concrete strain capacity. The discussion of the results includes a comparison with the values obtained using existing constitutive models. Study 3 proposes a new theoretical framework to interpret and capture the physics of the FRP confinement of square RC columns subjected to pure compressive loads. The geometrical, physical and mechanical parameters governing the problem are analyzed and discussed. A single-parameter methodology for predicting the axial stress - axial strain curve for FRP-confined square RC columns is described. Fundamentals, basic assumptions and limitations are discussed. A simple design example is also presented.

Slender structures are elegant aesthetically. The insufficiency in knowledge of the real resistance to buckling of very slender reinforced concrete columns leads to an exaggeration of the sizes of the columns. _The examples of concrete compression members cited and constructed in Industry on a global basis suggest that very slender columns have inherent safety both from the point of view of the ultimate strength and stability. The strengths of columns given. by the British codes would seem to be exceeded by many of the long slender reinforced concrete columns and struts which have been used Internationally. Both the theoretical and the experimental short term investigations have been carried out to establish the behaviour of hinged, very slender reinforced concrete columns at various stages'of axial loading. Forty three very slender reinforced concrete columns of two different square cross sections with two sizes of longitudinal reinforcements with lateral ties were cast. Slenderness rates, L A, were varied from 30 to 79. Special factors were obtained to relate the actual modulus of elasticity of concrete in columns at buckling failure to a knowledge of the initial modulus of elasticity of concrete in control cylinder specimens. Both theoretical and experimental graphs of load against moment, made dimensionless for critical sections of columns have been obtained. Dimensionless load-moment interaction diagrams using material failure as the criterion have been superimposed on these graphs to show considerable inherent material strength of the tested columns near buckling collapse failures. A theory using the fundamental approach has, been developed to predict the deflected shape and moments along the, heights of the columns at various stages of loading. The proposed theory predicts with good correlations the experimental deflections and moments of any loading stages of the columns. The theory has been used to obtain the required variables, to arrive at the initial predicted design loads of the investigated columns. Good correlations of the moments derived from observed strains have also been obtained. The developed theory predicts satisfactorily the buckling collapse loads of the columns. Although the theory has been derived for axially I loaded very slender reinforced concrete-columns, it seems to accept satisfactorily eccentricities of up to about 10 mm. This was confirmed after extensive comparisons of the theoretical buckling collapse loads with the applicable tests of other authors. Creep In the columns investigated was discovered to be one of the major factors for serious consideration. This was conclusively revealed from the observations on the last two very long term creep tests on columns. The actual safe sustained loads for these very slender columns of slenderness ratios, L/H, between 40 and 79 seem to be between 33% and 19% of the short term buckling collapse loads. The reduced modulus approach to predict the safe long term sustained loads seems to give reasonable values for L/H ratios of 40 and 50. The recommendations given for the proposed design of very slender reinforced concrete columns seem to be adequate and simple to use in practice. They are further simplified by the derivation of two equations for the reduction factors, R, for the slenderness ratios between 36 and 40 and between 40 and 79 respectively. The investigation has proved that very slender reinforced concrete columns are very dangerous structural members, as they tend to have violent buckling failures. Nevertheless, It must be prudent not to design against disaster at any cost. This Investigation seemed to have enhanced considerably knowledge of the design of very slender reinforced concrete columns.

The American Society of Civil Engineers (ASCE) Standard 41-06 Supplement No.1 (2007) assists engineers in modeling and evaluating the non-linear behavior of structures till collapse. Different levels of conservatism were used throughout the standard to produce modeling parameters for different structural elements, which leads to inconsistencies at the system level. Task to update current ASCE 41-06 provisions pertaining to RC structures is now handled by ACI (American Concrete Institute) committee 369 entitled “Seismic Repair and Rehabilitation”. This study is a part of ACI 369 committee’s effort. Existing provisions for non-linear analysis are re-assessed in this study for both rectangular and circular reinforced concrete columns. A database of 490 column tests was compiled for this project. Median rather than conservative estimates of non-linear modeling parameters were produced to achieve “best” estimates of structural behavior. Proposed modeling parameters show improved fit with experimental data over existing parameters. Data necessary for selection of acceptance criteria are provided. / text

Fiber reinforced polymer (FRP) composites have been increasingly used inconcrete construction. This research focused on the behavior of concrete columnsreinforced with FRP bars, or prestressed with FRP tendons. The methodology was basedthe ultimate strength approach where stress and strain compatibility conditions andmaterial constitutive laws were applied.Axial strength-moment (P-M) interaction relations of reinforced or prestressedconcrete columns with FRP, a linearly-elastic material, were examined. The analyticalresults identified the possibility of premature compression and/or brittle-tension failureoccurring in FRP reinforced and prestressed concrete columns where sudden andexplosive type failures were expected. These failures were related to the rupture of FRPrebars or tendons in compression and/or in tension prior to concrete reaching its ultimatestrain and strength. The study also concluded that brittle-tension failure was more likelyto occur due to the low ultimate tensile strain of FRP bars or tendons as compared to steel.In addition, the failures were more prevalent when long term effects such as creep andshrinkage of concrete, and creep rupture of FRP were considered. Barring FRP failure,concrete columns reinforced with FRP, in some instances, gained significant momentresistance. As expected the strength interaction of slender steel or FRP reinforcedconcrete columns were dependent more on column length rather than material differencesbetween steel and FRP.Current ACI minimum reinforcement ratio for steel (pmin) reinforced concretecolumns may not be adequate for use in FRP reinforced concrete columns. Design aidswere developed in this study to determine the minimum reinforcement ratio (pf,min)required for rectangular reinforced concrete columns by averting brittle-tension failure toa failure controlled by concrete crushing which in nature was a less catastrophic and moregradual type failure. The proposed method using pf,min enabled the analysis of FRPreinforced concrete columns to be carried out in a manner similar to steel reinforcedconcrete columns since similar provisions in ACI 318 were consistently used indeveloping these aids. The design aids produced accurate estimates of pf,min. Whencreep and shrinkage effects of concrete were considered, conservative pf,min values wereobtained in order to preserve an adequate margin of safety due to their unpredictability.

A total of 47 lightweight aggregate concrete columns were constructed from four different types of lightweight aggregate and provided with different quantities of transverse reinforcement. The specimens were tested under a monotonically increasing level of compressive axial load. The rate of load application was varied from pseudo-static to the rate of dynamic loading expected during a major seismic excitation. The results from the experimental testing of the column members were used to derive a theoretical stress-strain model to predict the behaviour of lightweight aggregate concrete members under imposed loads. The stress-strain model was derived to predict the response of both lightweight aggregate and conventional weight concretes with compressive strengths up to and including 100 MPa. The model was calibrate against the experimental results obtained in this study and previously tested lightweight aggregate and conventional weight concrete columns. A series of pseudo-cyclic moment-curvature analyse were undertaking using the derived stress-strain model, to predict the behaviour of the lightweight aggregate concrete members when subjected to axial load and flexure. The results were compared to the confinement requirements in the potential plastic hinge regions of column elements required by the New Zealand Concrete Structures Standard, NZS3101: 1995. It was determined that the confinement requirements of NZS3101: 1995 were could be used to accurately determine the required quantity of transverse reinforcement for lightweight aggregate concrete members with a concrete density greater than 1700 kg/m3. A total of four lightweight aggregate concrete beam column subassemblies were constructed and tested under reversed cyclic lateral loading. The results from the specimen indicate that cyclic behaviour of the lightweight aggregate concrete was similar to conventional weight concrete. However the bond capacity between the longitudinal reinforcement and the surrounding concrete was weaker than previously tested conventional weight concrete members.

Appropriate transverse confinement can significantly improve strength, ductility and energy dissipation capacity of reinforced concrete columns, therefore enhancing their seismic resistance. This study is conducted to evaluate the seismic behaviour of concrete columns transversely confined by steel spirals, ties or fiber reinforced polymer (FRP) wrapping. In the experimental program of this study, fifteen circular concrete columns of 356 mm (14 in.) diameter and 1473 mm (58 in.) length were tested under lateral cyclic displacement excursions while simultaneously subjected to constant axial load thus simulating earthquake loads. Eight columns were solely confined by various amounts of steel spirals, while seven other columns containing only minimal steel spirals were retrofitted by external FRP wrapping. Test results revealed that the increased transverse confinement can improve the energy dissipation capacity, ductility, deformability and flexural strength of concrete columns. The required transverse confinement should also be enhanced with the increase of axial load level to satisfy certain seismic design criterion. A computation program was developed to conduct monotonic pushover analysis for confined concrete columns, which can predict the envelope curves of moment vs. curvature and shear vs. deflection hysteresis loops with reasonable accuracy for columns subjected to simulated seismic loading. Based on extensive numerical analysis, expressions were developed for the relationships between the amount of transverse confinement and different ductility parameters, as well as the strength enhancement of confined columns. Finally, design procedures to determine the amount of transverse confinement were developed for concrete columns to achieve a certain ductility target. The enhancement of flexural strength of columns due to transverse confinement was also evaluated.