Semiconducting properties and related defect disorder for well defined TiO2 single crystal were studies. Semiconducting properties have been determined using simultaneous measurements of two independent electrical properties, including electrical conductivity, ??, and thermoelectric power, S, at elevated temperatures (1073-1323 K) in the gas phase of controlled oxygen activity (10-10 Pa &lt p(O2) &lt 75 kPa). Measurements of s and S were conducted (i) in the gas/solid equilibrium and (ii) during equilibration. Oxygen vacancies have been identified as the predominant defects in TiO2 over a wide range of p(O2). Individual conductivity components related to electrons, electron holes and ions, were determined from the obtained ?? data. The effect of p(O2) on these individual components was considered in the form of a diagram. This work led to the discovery of the formation and diffusion of Ti vacancies. However, the obtained diffusion data indicate that, in the temperature ranges commonly used in studies of semiconducting properties (1000-1400K), the Ti vacancies concentration is quenched and may thus be assumed constant. In addition it was shown that Ti vacancies in appreciable concentrations form only during prolonged oxidation. It was determined that the discrepancies in the reported n-p transition point are related to the concentration and spectrum of impurities as well as the concentration of Ti vacancies. It has been shown that the n-p transition point in high-purity TiO2 is determined by the Ti vacancy concentration. A well defined chemical diffusion coefficient, Dchem, was determined using kinetic data obtained during equilibration. A complex relationship between p(O2) and Dchem was observed. These data showed a good agreement between the obtained diffusion data and defect disorder. Examination of the determined equilibration kinetics, led to the discovery of two kinetic regimes, the result of the transport of defects at different mobilities. The determined data are considered well defined due to the following reasons: 1. The studied specimen was of exceptionally high purity and free of grain boundaries (single crystal) 2. The specimen was studied in the gas phase of controlled and well defined oxygen activity which was continuously monitored. 3. Whenever the experimental data were measured in equilibrium, the gas/solid equilibrium has been verified experimentally. 4. A good agreement between the two, self-confirmatory, electrical properties, including ?? and S has been determined simultaneously and independently. The defect disorder model derived in the present work may be used for tailoring controlled semiconducting properties through the selection of annealing conditions involving the temperature and oxygen activity.

Abstract not available

Abstract not available

We conduct a comprehensive and systematic study of the Fermi-Pasta-Ulam (FPU) model using both equilibrium and non-equilibrium molecular dynamics simulations, with the aim being to explain the cause of the anomalous energy-transport behaviour in the model. In the equilibrium scenario, our motivation stems from the lack of a complete understanding of the effects of initial conditions on the energy dissipation among Fourier modes. We also critically reconsider the ????probes' that had been widely used to quantitatively describe the types of energy sharing in a system, and then decide on a preferred choice to be used in our equilibrium study. We establish, from strong numerical evidence, that there exists a critical energy density of approximately 0:1, above which the energy dissipation among the modes becomes independent of initial conditions and system parameters, and that the full equipartition of mode energy is never attained in the FPU model. We report, for the first time, the violation of particle positions in the FPU model at high energies, where the particles are found to pass through one another. In the non-equilibrium scenario, we critically review the Nos???Se-Hoover algorithm thermostatting method largely used by other works, and identify its weaknesses. We also review some other alternative methods and decide on the most appropriate one to be implemented throughout our work. We confirm the divergence of the thermal conductivity of the FPU model as the chain length increases, and that kfpu [symbol] No.41, in agreement with other works. Our study further shows that there exists an upper limit of the anharmonicity in the FPU model, and that any attempt to increase the strength of this anharmonicity will not succeed. We also introduce elastic collisions into the original FPU model and find that the Modified model (FPUC) still exhibits anomalous thermal conductivity. We conclude that a one-dimensional FPU-type model with ????only' nearest-neighbour interaction, regardless of being soft or hard, does not exhibit a finite thermal conductivity as the system size increases, due to the non-chaotic nature of its microscopic dynamics, the origin of which we are unable to account for. Finally, we briefly outline possible research directions.

Masters Research - Master of Philosophy (Engineering) / Thermal conduction properties are of major concern for those metal/ceramic composite materials having applications in semiconductor devices and electronic packaging materials. A higher thermal conductivity to coefficient of thermal expansion ratio is an advantage for such materials employed in electronic devices due to the subjective high thermal loads. It is well known that the shape, size and distribution of the insulating phase have an effect on the overall thermal conductivity properties. But the details are lacking and well deserving of study. Metal/ceramic oxide interfaces are important in the strengthening mechanisms of dispersion strengthened materials. Accordingly, considerable attention has been given to recent investigations of oxygen diffusion characteristics and the bonding mechanisms at such interfaces. Susceptibility to oxidation can be studied by analysing several thicknesses of material. As an example, studying a thin film and a semi-infinite material subjected to a high oxygen partial pressure environment and a vacuum condition would help to determine the oxidation (in-diffusion) and de-oxidation (out-diffusion) processes respectively. Since metal/ceramic internal interfaces play a very important role in controlling the mechanical, thermal and electrical properties, it is timely to consider these diffusion processes for detailed study. In this Thesis, the two areas mentioned above were selected for detailed investigation. The Thesis also addresses the further development of a method for solving complex phenomenological diffusion problems. This method makes use of lattice-based random walks of virtual particles, directed according to the Monte Carlo method (the Lattice Monte Carlo method) which is then used to address various mass and thermal diffusion processes. Chapter 2 is concerned with using this method to determine the thermal conductivity of model composites. In that chapter, the Lattice Monte Carlo method is used to calculate the effective thermal conductivity of several models of a composite, where inclusions are arranged in square planar and cubic arrangements with periodic boundary conditions. Excellent agreement is found of the effective thermal conductivity with the century-old Maxwell-Garnett Equation. Chapter 3 is concerned with a phenomenological representation of oxygen diffusion and segregation in a model composite based on Ag/MgO. The Lattice Monte Carlo method is employed to address mass diffusion in this composite. Square and randomly distributed multiple inclusions were considered as shapes of the MgO inclusion phase. The time-dependence of oxygen concentration depth profiles and contour maps were determined. First, oxygen in-diffusion is considered from a constant surface source solely into the Ag metal matrix: oxygen depth profiles were in excellent agreement with exact results. Next, oxygen in-diffusion/segregation is simulated in the composite by permitting and restricting the mobility of oxygen in different scenarios involving the Ag-MgO interface. The (higher temperature) out-diffusion of oxygen from the composite was also simulated and corresponding results obtained for the oxygen depth profiles. In both cases, very good agreement was found between the results from the Lattice Monte Carlo method and analytical expressions.

Titanium dioxide, TiO2, has potential applications as a photoelectrode for photoelectrochemical generation of hydrogen by splitting water using solar energy and as a photocatalyst for water purification. This study is part of the UNSW research program to process TiO2-based oxide semiconductors as high-performance photoelectrodes and photocatalysts. This study investigates the effect of defect disorder on semiconducting properties of polycrystalline TiO2. This study involved the processing of high-purity polycrystalline TiO2 and determination of its semiconducting properties through measurement of electrical conductivity and thermoelectric power at elevated temperatures (1073-1323K) in controlled oxygen activities [1x10-13 Pa < p(O2) < 75 kPa]. The study included two types of experiments: Determination of electrical properties under conditions of gas/solid equilibrium. The data obtained was used to derive defect disorder and related semiconducting properties Monitoring of electrical properties during equilibration. This data was used to determine the chemical diffusion coefficient. The data obtained under equilibrium conditions indicates that oxygen may be used as a dopant to impose controlled semiconducting properties. In reduced conditions TiO2 is an n-type semiconductor and under oxidizing conditions TiO2 is a p-type semiconductor. The n-type behaviour is associated with oxygen vacancies as the predominant defects and titanium interstitials as the minority defects. The p-type behaviour is closely related to titanium vacancies that are formed during prolonged oxidation. Charge transport at elevated temperature was shown to involve substantial contribution from ions. Analysis of electrical properties enabled determination of several defect-related quantities including the activation enthalpy for oxygen vacancy formation, and the activation energy of the electrical conductivity components related to electrons, holes and ions. The kinetic data obtained during gas/solid equilibration enabled determination of the chemical diffusion coefficient which exhibited a complex dependence on nonstoichiometry. In addition, prolonged oxidation showed that equilibration occurred in two kinetic regimes. One for highly mobile oxygen vacancies and titanium interstitials which quickly reached an ??operational equilibrium?? within hours and another slow kinetic regime for equilibration of titanium vacancies over many thousand hours. The determined chemical diffusion coefficient data may be used to select the processing conditions required to impose uniform concentration of defects within a TiO2.

There is a need in the dairy industry for instrumentation capable of providing on-line information about the moisture content of cheese during manufacture. Present measurement techniques are usually performed off-line and can be susceptible to human error. It is demonstrated that microwave-based moisture sensing techniques offer a number of potential advantages over conventional methods due to the strong interaction of microwaves with water. The permittivity of cream cheese curd and low-fat cheddar cheese curd has been measured over a range of frequencies and moisture contents in order to establish the relationship between these variables. A vector reflection coefficient measurement engine based on a six-port reflectometer has been built and tested. A suitable sensing head has been fabricated from a short length of microstrip transmission line. Two sensor characterisation models have been developed and compared with measured data. A novel algorithm has been developed to resolve the ambiguity inherent in many permittivity measurement techniques. It has been discovered that surface waves can propagate on a grounded dielectric slab covered by a material with a higher dielectric constant, provided the loss factor of the covering medium is greater than zero. It has also been found that the dominant mode of microstrip can radiate when the line is covered by a high-permittivity material, although this can be suppressed if the covering material is sufficiently lossy. There are three principal conclusions to draw from the investigation in this thesis. Firstly, changes in the moisture content of cheese curd during manufacture produce measurable variations in permittivity. Secondly, these changes can be measured accurately and cheaply using off-the-shelf microwave hardware. Finally, considerable attention must be paid to the characterisation of the sensing head if the instrument is to achieve its full potential. Promising results have been obtained in this area, however certain issues pertaining to the propagation of multiple dominant modes and higher order modes have not been fully resolved and would repay further theoretical analysis.

Polymer composites formed from layered fillers with high surface volume ratio show enhanced reinforcement. Graphite oxide is a high modulus material that can be separated into thin layers with high surface area. The aim of this study is to prepare polymer layered graphite oxide composites using functionalised polyolefin to enhance compatibility with various forms of layered graphite oxide in varying concentration. Functionalised polyolefins reinforced with layered graphite oxides and expanded graphite oxides were prepared using solution blending and melt blending methods. Three different mixing methods with varying shear intensity were employed to prepare polymer layered graphite oxide composites. The crystalline structure, thermal and mechanical properties of the prepared polymer layered graphite oxide composites was studied. Oxidised graphite prepared from the Staudenmaier method and its exfoliated form were dispersed in poly(ethylene-co-methyl acrylate-co-acrylic acid) (EMAA) via solution blending to prepare EMAA layered composites. The thermal stability was determined using thermogravimetric analysis. The EMAA layered composites showed higher thermal stability in comparison with pure EMAA. The mechanical properties of these EMAA layered composites were determined through dynamic mechanical analysis. Shear modulus, yield stress and storage modulus of EMAA in the presence of graphite oxide fillers decreased. A solution blending method was used to prepare poly(propylene-grafted-maleic anhydride) layered expanded graphite oxide composites (PPMA-EGO). Two types of PPMA-EGO were prepared using different mixing methods - low and high shear were employed. The effects of preparative mixing methods on the PPMA-EGO properties were investigated. The mechanical properties of PPMA-EGO obtained from dynamic mechanical analysis indicated that EGO had a reinforcing effect on the elastic behaviour of PPMA-EGO. This is due to strong interfacial adhesion between PPMA and EGO as a result of hydrogen bonding. The elastic behaviour of PPMA-EGO was affected by the surface area of graphite flakes. Low sheared PPMA-EGO elastic behaviour was found to be higher compared with that of high sheared PPMA-EGO. A melt blending method was used to prepare PPMA-EGO with varying EGO concentration. The interconnected network structure of EGO in the PPMA-EGO was not observed as shown by its scanning electron microscopy images. Thermogravimetric analysis of PPMA-EGO indicates increased decomposition temperature of the PPMA matrix. Dynamic mechanical analysis showed enhanced storage modulus of PPMA-EGO. The maximum elastic modulus of PPMA-EGO was observed at 3 %wt of EGO. The electrical conductivity of PPMA-EGO was measured only for EGO concentrations above 2 %wt. The EGO concentration was found to be the most critical factor in the enhancement of the electrical conductivity of PPMA-EGO. Wide angle X-ray diffraction analysis of all polymer layered graphite oxide composites revealed no change in interlayer spacing of graphite layers, indicating the absence of EMAA intercalation in the graphite layers. The crystallisation temperature and crystallinity of all polymer layered graphite oxide composites were determined using differential scanning calorimetry. The results indicated that graphite oxide and expanded graphite oxides acted as nucleating agents in inducing the crystallisation of functionalised polyolefin in the layered composites. However, the degree of crystallinity of functionalised polyolefin decreased in the layered composites.

<p>The magnitude of an electric field possible to apply in a capillary separation system is limited, because a high electric field causes a too high current through the capillary. Application of the electric field <i>in-line</i> will give an increased conductivity in the column, further increasing the risk of too high currents. The conductivity changes were found to result from an overall increase in ionic strength within the electric field. The increase in ionic strength is caused by the increase in mobile phase ions with electrophoretic velocity against the flow, together with OH^- or H₃O⁺ ions (depending on polarity) formed at the inlet electrode. Further it was found that the use of a pressurized reservoir or splitting of the flow at the inlet electrode could significantly limit the conductivity changes and thereby the maximum applicable electric field strengths could be increased.</p>

<p>The thesis describes an investigation into the interaction between the conducting polymer and cellulosic materials, and the preparation of electroconductive paper. The adsorption behavior of the conducting polymer onto cellulosic materials was characterized. Poly(3,4-ethylenedioxythiophene) doped with poly(4-styrene sulfonate) (PEDOT:PSS) was used as conducting polymer because of its attractive properties in terms of conductivity, water solubility, and environmental stability. The model substrate used for adsorption was microcrystalline cellulose (MCC). Various pH levels and salt concentrations were explored to completely understand the adsorption behavior of PEDOT:PSS. The variation in surface charge characteristics when the pH and salt concentration were changed was monitored by polyelectrolyte titration and zeta potential measurement. The adsorption isotherm showed a broad molecular distribution of the conducting polymer and considerable interaction between the polymer and MCC. As the pH of the solution was increased, the adsorbed amount decreased. With varying salt concentrations, the adsorption passed through a maximum. The extent of deposition of PEDOT:PSS on the surface of cellulosic fibers was investigated using X-ray Photoelectron Spectroscopy (XPS) with a commercial base paper as substrate. XPS analysis of dip-coated paper samples showed PEDOT enrichment on the surface. The degree of washing the dip-coated paper with acidic water did not significantly affect the PEDOT enrichment on the surface.</p><p> </p><p>A base paper was coated with PEDOT:PSS blends to produce electroconductive papers. The bulk conductivities (σ_dc) of the coated papers were measured using a four-probe technique and impedance spectroscopy. One-side and two-side coating gave comparable conductivity levels. Various organic solvents added to the PEDOT:PSS dispersion at different concentrations showed various effects on the bulk conductivity of the coated paper. Blends containing sorbitol and isopropanol did not enhance the bulk conductivity of the coated paper, and at high concentrations these organic solvents lowered the conductivity. Paper samples coated with a PEDOT:PSS blend containing N-methylpyrrolidinone (NMP) and dimethyl sulfoxide (DMSO) exhibited a higher conductivity than when coated with pure PEDOT:PSS, due to conformational changes and their plasticizing effect. The effect of calendering was investigated and only the sample subjected to 174 kN/m line load after coating showed significant conductivity enhancement. The addition of TiO₂ pigment lowered the bulk conductivity of the paper. Contact angle measurements were made to monitor the effect of coating the paper with PEDOT:PSS blends on the hydrophilicity of the paper samples. The amount of PEDOT:PSS deposited in the fiber network was determined using total sulfur analysis. Thus, this study makes use of conventional paper surface treatment as method for achieving bulk conductivity of paper in the semi-conductor range without significantly decreasing the paper strength.</p> / Printed Polymer Electronics